As a temporary measure, the code to implement PIO transfers was
duplicated in zorro_esp and mac_esp. Now that it has stabilized move the
common code into the core driver but don't build it unless needed.
This replaces the inline assembler with more portable writesb() calls.
Optimizing the m68k writesb() implementation is a separate patch.
[mkp: applied by hand]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a target disconnects during a PIO data transfer the command may fail
when the target reconnects:
scsi host1: DMA length is zero!
scsi host1: cur adr[04380000] len[00000000]
The scsi bus is then reset. This happens because the residual reached
zero before the transfer was completed.
The usual residual calculation relies on the Transfer Count registers.
That works for DMA transfers but not for PIO transfers. Fix the problem
by storing the PIO transfer residual and using that to correctly
calculate bytes_sent.
Fixes: 6fe07aaffb ("[SCSI] m68k: new mac_esp scsi driver")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Except for the mac_esp driver, which uses PIO or pseudo DMA, all drivers
share the same dma mapping calls. Move the dma mapping into the core
code using the scsi_dma_map / scsi_dma_unmap helpers, with a special
identify mapping variant triggered off a new ESP_FLAG_NO_DMA_MAP flag
for mac_esp.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can simplify use esp->dev now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
esp->dev is a void pointer that points either to a struct device, or a
struct platform_device. As we can easily get from the device to the
platform_device if needed change it to always point to a struct device
and properly type the pointer to avoid errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When in MESSAGE IN phase, the ESP device does not automatically
acknowledge each byte that is transferred by PIO. The mac_esp driver
neglects to explicitly ack them, which causes a timeout during messages
larger than one byte (e.g. tag bytes during reconnect). Fix this with an
ESP_CMD_MOK command after each byte.
The MESSAGE IN phase is also different in that each byte transferred
raises ESP_INTR_FDONE. So don't exit the transfer loop for this interrupt,
for this phase.
That resolves the "Reconnect IRQ2 timeout" error on those Macs which use
PIO transfers instead of PDMA. This patch also improves on the weak tests
for unexpected interrupts and phase changes during PIO transfers.
Tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 02507a80b3 ("[PATCH] [SCSI] mac_esp: fix PIO mode, take 2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid the following warning from "make C=1":
CHECK drivers/scsi/mac_esp.c
drivers/scsi/mac_esp.c:357:30: warning: incorrect type in initializer (different address spaces)
drivers/scsi/mac_esp.c:357:30: expected unsigned char [usertype] *fifo
drivers/scsi/mac_esp.c:357:30: got void [noderef] <asn:2>*
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit da244654c6 ("[SCSI] mac_esp: fix for quadras with two esp
chips") added mac_scsi_esp_intr() to handle the IRQ lines from a pair of
on-board ESP chips (a normal shared IRQ did not work).
Proper mutual exclusion was missing from that patch. This patch fixes
race conditions between comparison and assignment of esp_chips[]
pointers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
My email address may be found in the git commit logs and in MAINTAINERS.
Remove duplicate addresses so they won't have to be kept up-to-date.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename the "Mac ESP" irq as "ESP" to be consistent with all the other Mac
drivers and ESP drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
mac_irq_pending() has only one caller (mac_esp.c). Nothing tests for Baboon, PSC or OSS pending interrupts. Until that need arises, let's keep it simple and remove all the unused abstraction. Replace it with a routine to check for SCSI DRQ.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Mutual exclusion is redundant here because all the paths in the call graph
leading to esp_driver_ops.send_dma_cmd() happen under spin_lock_irqsave/
spin_lock_irqrestore. Remove it.
Tested on a Mac Quadra 660av and a Mac LC 630.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Move platform device code from the driver to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The mac_esp PIO algorithm no longer works in 2.6.31 and crashes my Centris
660av. So here's a better one.
Also, force async with esp_set_offset() rather than esp_slave_configure().
One of the SCSI drives I tested still doesn't like the PIO mode and fails
with "esp: esp0: Reconnect IRQ2 timeout" (the same drive works fine in
PDMA mode).
This failure happens when esp_reconnect_with_tag() tries to read in two
tag bytes but the chip only provides one (0x20). I don't know what causes
this. I decided not to waste any more time trying to fix it because the
best solution is to rip out the PIO mode altogether and use the DMA
engine.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On the Quadra 900 and 950 there are two ESP chips sharing one IRQ. Because
the shared IRQ is edge-triggered, we must make sure that an IRQ transition
from one chip doesn't go unnoticed when the shared IRQ is already active
due to the other. This patch prevents interrupts getting lost so that both
SCSI busses may be used simultaneously.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix asm constraints and arguments so as not to transfer an odd byte when
there may be more words to transfer. The bug would probably also cause
exceptions sometimes by transferring one too many bytes.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
... and we have few enough places using the latter to make it
simpler to do search and replace...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the mac_esp driver with a new one based on the esp_scsi core.
For esp_scsi: add support for sync transfers for the PIO mode, add a new
esp_driver_ops method to get the maximum dma transfer size (like the old
NCR53C9x driver), and some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
These drivers depend on the deprecated NCR53C9X core and need to be converted
to the esp_scsi core.
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Linux/m68k <linux-m68k@vger.kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is a set of changes that converts the PMAZ-A support to the driver model.
The use of the driver model required switching to the hotplug SCSI
initialization model, which in turn required a change to the core NCR53C9x
driver. I decided not to break all the frontend drivers and introduced an
additional parameter for esp_allocate() to select between the old and the new
model. I hope this is OK, but I would be fine with converting NCR53C9x to the
new model unconditionally as long as I do not have to fix all the other
frontends (OK, perhaps I could do some of them ;-) ).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Finn Thain