the check of the return code is missing, user space does not get notified
about the error condition:
omapdss OVERLAY error: overlay 2 horizontally not inside the display area (403 + 800 >= 800)
omapdss APPLY error: failed to apply settings: illegal configuration.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for DRA7xx DPI output.
DRA7xx has three DPI outputs, each of which gets its input from a DISPC
channel. However, DRA72x has only one video PLL, and DRA74x has two
video PLLs. In both cases the video PLLs need to be shared between
multiple outputs. The driver doesn't handle this at the moment.
Also, DRA7xx requires configuring CONTROL module bits to route the clock
from the PLL to the used DISPC channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for DRA7xx to the HDMI driver.
The HDMI block on DRA7xx is the same as on OMAP5, except we need to
enable and disable the HDMI PLL via the CONTROL module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.
This patch adds support to write the polarities to control module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRA7xx SoCs have one (DRA72x) or two (DRA74x) video PLLs. They are
basically the same as DSI PLLs on OMAPs, but without the rest of the DSI
hardware. The video PLLs also require some configuration via the CONTROL
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add functions which configure the control module register
CTRL_CORE_DSS_PLL_CONTROL found in DRA7xx SoCs. This register configures
whether the PLL registers are accessed internally by DSS, or externally
using OCP2SCP interface. They also configure muxes which route the PLL
output to a particular LCD overlay manager within DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A race issue has been observed with the encoder-tpd12s015 driver, which
leads to errors when trying to read EDID. This has only now been
observed, as OMAP4 and OMAP5 boards used SoC's GPIOs for LS_OE GPIO. On
dra7-evm boards, the LS_OE is behind a i2c controlled GPIO expander,
which increases the time to set the LS_OE.
This patch simplifies the handling of the LS_OE gpio in the driver by
removing the interrupt handling totally. The only time we actually need
to enable LS_OE is when we are reading the EDID, and thus we can just
set and clear the LS_OE gpio inside the read_edid() function.
This also has the additional benefit of very slightly decreasing the
power consumption.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP5 HW supports directing DIGIT channel to DPI output, but the
driver doesn't support that. However, we have marked that configuration
as possible in the dss features, so in certain cases the driver tries to
use that configuration, leading to broken display.
Fix the problem by allowing DIGIT channel to go only to HDMI output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In some cases we need global identifiers for the DSS PLLs, for example
when configuring clock muxing on DRA7. For this purpose let's add a
'enum dss_pll_id'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The sys_copyarea() function performs the same operation as
cfb_copyarea() but using normal memory access instead of I/O
accessors. Since the introduction of sys_copyarea(), there
have been two fixes to cfb_copyarea():
- 00a9d699 ("framebuffer: fix cfb_copyarea")
- 5b789da8 ("framebuffer: fix screen corruption when copying")
This patch incorporates the fixes into sys_copyarea() as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The frame buffer core can be a module, which means any fb drivers
should be able to build as modules too. This turns mmpfb into
a tristate option to allow that and fix a possible randconfig
build error.
drivers/built-in.o: In function `modes_setup':
:(.text+0x11b34): undefined reference to `fb_videomode_to_modelist'
:(.text+0x11b5c): undefined reference to `fb_videomode_to_var'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Device driver should not directly select subsystems. In this case
we get build warnings like
warning: (ARCH_REQUIRE_GPIOLIB && PINCTRL_AT91 && PINCTRL_NOMADIK && MFD_TC6393XB && FB_VIA) selects GPIOLIB which has unmet direct dependencies (ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB)
which we can avoid using the normal 'depends on' statement.
Also, this patch makes it possible for DRM drivers to have a dependency
on GPIOLIB without getting circular Kconfig dependencies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes ssd1307fb_ssd1306_init() function to return
proper error codes in case of failures.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
As per the suggestion of Thierry Reding rename
HDMI_AUDIO_CODING_TYPE_EXT_STREAM to HDMI_AUDIO_CODING_TYPE_EXT_CT to
be consistent with the CEA-861 spec.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When receiving video it is very useful to be able to unpack the InfoFrames.
Logging is useful as well, both for transmitters and receivers.
Especially when implementing the VIDIOC_LOG_STATUS ioctl (supported by many
V4L2 drivers) for a receiver it is important to be able to easily log what
the InfoFrame contains. This greatly simplifies debugging.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
CVT v1.1 spec says: "the vertical front porch shall in all cases be
fixed to 3 lines". The code in fbcvt.c instead sets the _back_ porch to
3 (plus margin).
After swapping cvt.v_front_porch and cvt.v_back_porch the resulting
timings were in line with CVT timings in VESA DMT spec.
The bug seems to be more than 9 years old, but I presume it has not been
noticed as usually the video timings come from the EDID or from the
timing tables in fbdev, and probably swapped values for vfp and vbp work
fine for most of the displays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: David Ung <davidu@nvidia.com>
Cc: Antonino A. Daplas <adaplas@gmail.com>
var->yoffset is of the type __u32, hence the comparison will always
be false.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use NULL instead of 0 for the last entry of dmt_modes struct.
Supresses "sparse: Using plain integer as NULL pointer" warning.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
IRQ_TYPE_PRIO is no longer used by the Atari platform interrupt code
since commit 734085651c ("[PATCH] m68k: convert atari irq code")
in v2.6.18-rc1, so drop it.
Note that its value has been reused for a different purpose
(IRQ_TYPE_EDGE_FALLING) since commit 6a6de9ef58 ("[PATCH] genirq:
core") in v2.6.18-rc1.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fbmon may generate mode timings that are out of spec of the monitor.
eg DELL U2410 has a max clock 170mhz but advertises a resolutions of
1920x1200@60 in its Standard Timings using 2byte code of D1 00.
When this is looked up in the DMT table it gives it a 193mhz clock.
Although the DELL monitor supports 1920x1200@60, it can only run with
reduced timings at 154mhz or DMT id 0x44 which has no STD 2byte code.
This patch checks to see if the mode can be supported by the monitor
by comparing against monspecs.dclkmax.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the VESA Display Monitor Timing (DMT) table.
During parsing of Standard Timings, it compare the 2 byte STD code
with DMT to see what the VESA mode should be. If there is no entry
in the vesa_modes table or no match found, it fallsback to the
GTF timings.
Signed-off-by: David Ung <davidu@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch sets the default height if its not found in DT.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch drops the unused function ssd1307fb_write_data().
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
commit 765d5b9c2b ("fbdev: fbcon: select
VT_HW_CONSOLE_BINDING") made FRAMEBUFFER_CONSOLE always select
VT_HW_CONSOLE_BINDING, but forgot to remove
select VT_HW_CONSOLE_BINDING if FRAMEBUFFER_CONSOLE
from the individual drivers' sections that already did this before.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
static code analysis from cppcheck reports:
[drivers/video/fbdev/broadsheetfb.c:673]:
(error) Memory leak: sector_buffer
sector_buffer is not being kfree'd on each call to
broadsheet_spiflash_rewrite_sector(), so free it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
PA-RISC already handled the dummy console screen size selection in
Kconfig, so generalize this to other platforms.
ARM keeps on using screen_info, which is filled in by
platform-specific code, or from ATAGS.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
continue is not needed at the end of a for loop, also removed the
braces which were no longer required.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
vga_in8() was storing the return value in tmp, but that return value
was never used again. so it should be safe to remove those variables.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
the check for info is not required as we are checking it immediately
after gxfb_init_fbinfo() and lxfb_init_fbinfo() and returnig -ENOMEM
if it is NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Assigning ddata->invert_polarity to itself is not very useful; the
context suggests that the right-hand side should have been
pdata->invert_polarity.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
of_platform_device_create is only defined when CONFIG_OF_ADDRESS is set,
which is normally always the case when CONFIG_OF is defined, except on Sparc,
so explicitly check for CONFIG_OF_ADDRESS rather then for CONFIG_OF.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When allocate framebuffer memory using dma_alloc_coherent(),
we'd better use dma_addr_t instead of phys_addr_t. Because the
address we got in fact is DMA or bus address for the platform.
This patch also fixes below build warning:
drivers/video/fbdev/ocfb.c:335:2:
warning: passing argument 3 of ‘dma_alloc_attrs’
from incompatible pointer type [enabled by default]
Signed-off-by: Qiang Chen <qiang2.chen@sonymobile.com>
Acked-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
opa362 is amplifier for video and can be connected to the tvout pads
of the OMAP3. It has one gpio control for enable/disable of the output
(high impedance).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
the check for info is not required as we are checking it immediately
after gx1fb_init_fbinfo() and returnig -ENOMEM if it is NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can mark the DMI system id table as __initconst by using a helper
variable that'll tell us if we need to unregister the reboot notifier in
atyfb_exit() instead of matching the DMI system id again.
This frees up ~680 bytes of runtime memory, the DMI table occupies.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
After the commit ef691ff48b (OMAPDSS: DT: Get source endpoint by
matching reg-id) we look for the SDI output using the port number.
However, the SDI driver doesn't set the port number, which causes the
SDI display to not initialize.
Fix this by setting the SDI port number to 1. We use a hardcoded value,
as SDI was used only on OMAP3 and it's always port number 1 there.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
fb_deferred_io_fsync() returns the value of schedule_delayed_work() as
an error code, but schedule_delayed_work() does not return an error. It
returns true/false depending on whether the work was already queued.
Fix this by ignoring the return value of schedule_delayed_work().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
If the probe of an fb driver has been deferred due to missing
dependencies, and the probe is later ran when a module is loaded, the
fbdev framework will try to find a logo to use.
However, the logos are __initdata, and have already been freed. This
causes sometimes page faults, if the logo memory is not mapped,
sometimes other random crashes as the logo data is invalid, and
sometimes nothing, if the fbdev decides to reject the logo (e.g. the
random value depicting the logo's height is too big).
This patch adds a late_initcall function to mark the logos as freed. In
reality the logos are freed later, and fbdev probe may be ran between
this late_initcall and the freeing of the logos. In that case we will
miss drawing the logo, even if it would be possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: stable@vger.kernel.org
The regulator_disable() doesn't accept NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI hardware parameters structs for OMAP4 and OMAP5 contained two
initializers for 'clkdco_max'. The first one was a remnant with wrong
value.
Remove the extra initializer entries.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.
Make these changes in 2 files under drivers/video/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Pull ARM updates from Russell King:
"The major updates included in this update are:
- Clang compatible stack pointer accesses by Behan Webster.
- SA11x0 updates from Dmitry Eremin-Solenikov.
- kgdb handling of breakpoints with read-only text/modules
- Support for Privileged-no-execute feature on ARMv7 to prevent
userspace code execution by the kernel.
- AMBA primecell bus handling of irq-safe runtime PM
- Unwinding support for memset/memzero/memmove/memcpy functions
- VFP fixes for Krait CPUs and improvements in detecting the VFP
architecture
- A number of code cleanups (using pr_*, removing or reducing the
severity of a couple of kernel messages, splitting ftrace asm code
out to a separate file, etc.)
- Add machine name to stack dump output"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (62 commits)
ARM: 8247/2: pcmcia: sa1100: make use of device clock
ARM: 8246/2: pcmcia: sa1111: provide device clock
ARM: 8245/1: pcmcia: soc-common: enable/disable socket clocks
ARM: 8244/1: fbdev: sa1100fb: make use of device clock
ARM: 8243/1: sa1100: add a clock alias for sa1111 pcmcia device
ARM: 8242/1: sa1100: add cpu clock
ARM: 8221/1: PJ4: allow building in Thumb-2 mode
ARM: 8234/1: sa1100: reorder IRQ handling code
ARM: 8233/1: sa1100: switch to hwirq usage
ARM: 8232/1: sa1100: merge GPIO multiplexer IRQ to "normal" irq domain
ARM: 8231/1: sa1100: introduce irqdomains support
ARM: 8230/1: sa1100: shift IRQs by one
ARM: 8229/1: sa1100: replace irq numbers with names in irq driver
ARM: 8228/1: sa1100: drop entry-macro.S
ARM: 8227/1: sa1100: switch to MULTI_IRQ_HANDLER
ARM: 8241/1: Update processor_modes for hyp and monitor mode
ARM: 8240/1: MCPM: document mcpm_sync_init()
ARM: 8239/1: Introduce {set,clear}_pte_bit
ARM: 8238/1: mm: Refine set_memory_* functions
ARM: 8237/1: fix flush_pfn_alias
...
* support for mx6sl and mx6sx
* OMAP HDMI audio rewrite to make it finally work
* OMAP video PLL work to prepare for new DRA7xx SoCs
* simplefb DT related improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAZB
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- support for mx6sl and mx6sx
- OMAP HDMI audio rewrite to make it finally work
- OMAP video PLL work to prepare for new DRA7xx SoCs
- simplefb DT related improvements
* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
video: smscufx: Deletion of unnecessary checks before the function call "vfree"
video: udlfb: Deletion of unnecessary checks before the function call "vfree"
video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
video: fbdev: arkfb: suppress build warning
video: fbdev: s3fb: suppress build warning
video: fbdev: vt8623fb: suppress build warning
OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
OMAPDSS: Remove all references to obsolete HDMI audio callbacks
ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
...
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0PNI
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
Pull x86 mm tree changes from Ingo Molnar:
"The biggest change is full PAT support from Jürgen Gross:
The x86 architecture offers via the PAT (Page Attribute Table) a
way to specify different caching modes in page table entries. The
PAT MSR contains 8 entries each specifying one of 6 possible cache
modes. A pte references one of those entries via 3 bits:
_PAGE_PAT, _PAGE_PWT and _PAGE_PCD.
The Linux kernel currently supports only 4 different cache modes.
The PAT MSR is set up in a way that the setting of _PAGE_PAT in a
pte doesn't matter: the top 4 entries in the PAT MSR are the same
as the 4 lower entries.
This results in the kernel not supporting e.g. write-through mode.
Especially this cache mode would speed up drivers of video cards
which now have to use uncached accesses.
OTOH some old processors (Pentium) don't support PAT correctly and
the Xen hypervisor has been using a different PAT MSR configuration
for some time now and can't change that as this setting is part of
the ABI.
This patch set abstracts the cache mode from the pte and introduces
tables to translate between cache mode and pte bits (the default
cache mode "write back" is hard-wired to PAT entry 0). The tables
are statically initialized with values being compatible to old
processors and current usage. As soon as the PAT MSR is changed
(or - in case of Xen - is read at boot time) the tables are changed
accordingly. Requests of mappings with special cache modes are
always possible now, in case they are not supported there will be a
fallback to a compatible but slower mode.
Summing it up, this patch set adds the following features:
- capability to support WT and WP cache modes on processors with
full PAT support
- processors with no or uncorrect PAT support are still working as
today, even if WT or WP cache mode are selected by drivers for
some pages
- reduction of Xen special handling regarding cache mode
Another change is a boot speedup on ridiculously large RAM systems,
plus other smaller fixes"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86: mm: Move PAT only functions to mm/pat.c
xen: Support Xen pv-domains using PAT
x86: Enable PAT to use cache mode translation tables
x86: Respect PAT bit when copying pte values between large and normal pages
x86: Support PAT bit in pagetable dump for lower levels
x86: Clean up pgtable_types.h
x86: Use new cache mode type in memtype related functions
x86: Use new cache mode type in mm/ioremap.c
x86: Use new cache mode type in setting page attributes
x86: Remove looking for setting of _PAGE_PAT_LARGE in pageattr.c
x86: Use new cache mode type in track_pfn_remap() and track_pfn_insert()
x86: Use new cache mode type in mm/iomap_32.c
x86: Use new cache mode type in asm/pgtable.h
x86: Use new cache mode type in arch/x86/mm/init_64.c
x86: Use new cache mode type in arch/x86/pci
x86: Use new cache mode type in drivers/video/fbdev/vermilion
x86: Use new cache mode type in drivers/video/fbdev/gbefb.c
x86: Use new cache mode type in include/asm/fb.h
x86: Make page cache mode a real type
x86: mm: Use 2GB memory block size on large-memory x86-64 systems
...
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
This patch adds a supply regulator to the lp855x platform data to facilitate
powering on/off the 3V rail attached to the controller.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch refactors the dt parsing code to avoid setting platform_data,
instead just setting lp->pdata directly. This facilitates easier
probe deferral since the current scheme would require us to clear out
dev->platform_data before deferring.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use per-device clock (instead of calling cpufreq_get(0), which can
return 0 if no cpu frequency driver is selected) to program timings.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The platform_device_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The framebuffer_release() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mmp_unregister_path() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The backlight_device_unregister() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The i2c_put_adapter() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The pci_dev_put() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vfree() function performs also input parameter validation. Thus the test
around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The uvesafb_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes following build warning:
drivers/video/fbdev/arkfb.c: In function ‘ark_pci_probe’:
drivers/video/fbdev/arkfb.c:1019:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
par->state.vgabase = (void __iomem *) vga_res.start;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes following build warning:
drivers/video/fbdev/s3fb.c: In function ‘s3_pci_probe’:
drivers/video/fbdev/s3fb.c:1185:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
par->state.vgabase = (void __iomem *) vga_res.start;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this patch fixes following build warning:
drivers/video/fbdev/vt8623fb.c: In function ‘vt8623_pci_probe’:
drivers/video/fbdev/vt8623fb.c:734:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
par->state.vgabase = (void __iomem *) vga_res.start;
^
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The bit field for IEC958_AES2_CON_SOURCE is bits 3-0 in
HDMI_CORE_FC_AUDSCHNLS2, not imaginary bits 3-4 (reverse order).
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove __exit qualifier from hdmi_uninit_output() because it is used
also in omapdss_hdmihw_probe().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Enabling idle mode during audio playback causes the glitches on OMAP5
HDMI. The TRM also suggests to use no-idle for HDMI audio playback.
This patch sets HDMI idle mode to no-idle for the duration of the
playback, and restores it back to original value afterwards.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In new model these callbacks are obsolete since the ASoC component
drivers are integrated into the HDMI drivers and no callbacks are
needed anymore.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes the OMAP5 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Removes the OMAP4 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Make hdmi_mode_has_audio() more user friedly by taking hdmi_config as
parameter.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The booleans are not used anymore. Just select SND_OMAP_SOC_HDMI_AUDIO
to enable OMAP HDMI audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adds display_enabled flag and audio_abort_cb callback to struct hdmi.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This is used to store omap-hdmi-audio pdev for unregistering it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Unify the private anonymous struct in hdmi4.c and hdmi5.c, name it as
struct omap_hdmi, and make it public in hdmi.h.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The audio dma port is found in the hdmi_wp physical address space.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It does not waste too many bytes to compile all audio related core
functions always in with HDMI support. It should help readability and
in keeping the audio code in working shape. Leave the options just for
disabling and enabling the functionality in hdmi[45].c.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The OMAP5 HDMI audio implementation needs HDMI_AUDIO_LAYOUT_6CH in
hdmi_core_audio_layout enum. I found the correct value from ti-linux
3.8 tree.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi_wp_audio_config_format() expects sample_order of struct
hdmi_audio_format to be initialized. The only allowed value is
HDMI_AUDIO_SAMPLE_LEFT_FIRST.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Only OMAP4 DSS has non reserved bits above 6th bit in HDMI_WP_AUDIO_CFG.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Both CONFIG_OF and CONFIG_COMMON_CLK must be defined to be able to use of
clocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
A word was corrected in the description for a parameter of
the mmp_unregister_path() function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Two mistyped words were corrected in the description for
the mmp_unregister_path() function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove Kconfig options used nowhere.
The removal of CONFIG_ARCH_AT91SAM9261 option allowed to spot this oddness.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch fixes duplicated include dma-mapping.h in
drivers/video/fbdev/amba-clcd.c
Signed-off-by: Qiang Chen <qiang2.chen@sonymobile.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
One of the reasons for having the simplefb nodes in /chosen, and doing
explicit enumeration of the nodes there, is too allow enumerating them sooner,
so that we get a console earlier on.
Doing this earlier then fs_initcall is not useful, since the fb only turns
into a console when fbcon intializes, which is a fs_initcall too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Various fb drivers register themselves before module_init so as to have a
console as early as possible, this is of little use if fbcon does not
initialize early too.
Fbcon cannot initialize earlier then fs_initcall, because then the creation
of /sys/class/graphics/fbcon will fail.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Update simplefb to support the new preferred location for simplefb dt nodes
under /chosen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This claims and enables clocks listed in the simple framebuffer dt node.
This is needed so that the display engine, in case the required clocks
are known by the kernel code and are described in the dt, will remain
properly enabled.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Change clks from list to dynamic array]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the usual kernel style of goto error_foo to free resources on probe
error. This is a preparation patch for adding clocks support.
While at it also update ioremap_wc error return from ENODEV to ENOMEM.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a proper struct describing simplefb private data, with the palette in there,
instead of directly storing the palette in the fb_info->par pointer.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Stephen Warren <swarren@nvidia.com>
[hdegoede@redhat.com: drop unnecessary void * cast]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the DSS has the common DSS PLL, we no longer use the DSI PLL
feature flags from dss_features.c.
Remove all the unused feature flags.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that we have the common DSS PLL support, change HDMI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.
The function to program the PLL settings can be removed from hdmi_pll.c,
as the common PLL API contains the same functionality.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
hdmi_pll_enable powers off the PLL as the first thing it does. Right
after that, it enables the PLL powers.
The initial power-off is pointless, so let's remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we have one function, hdmi_pll_enable, which enables the
PLL and writes the PLL configuration to registers.
To make the HDMI PLL ahere to the DSS PLL API, split the hdmi_pll_enable
into two parts: hdmi_pll_enable which enables the PLL HW, and
hdmi_pll_set_config which writes the config.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL code needs the pointer to the WP block so that it can manage
its power. Currently this is passed as a function parameter to
hdmi_pll_enable and hdmi_pll_disable. To make the PLL function adhere to
the DSS PLL API, we need to remove the WP parameter.
This patch stores the WP pointer to hdmi_pll_data in hdmi_pll_init, so
that it's available when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SYSRESET bits in HDMI PLL do not reset the PLL itself, but only
affect the power used for the PLL.
Afaik there is no reason to use the SYSRESET bits, and we don't use it
in the other PLLs, so let's remove the HDMI PLL reset to make the PLL
code simpler and similar to other PLLs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The code calculating HDMI PLL parameters has always been very confusing.
Now that we are implementing a common PLL library for the DSS, it's
important that the PLL code is understandable.
This patch rewrites the calculation code, and removes a few hacks that
were used there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't support interlace modes properly on OMAP5+ HDMI, so we need to
reject interlace timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Only OMAP5+ has REFSEL field, but at the moment it's set also on OMAP4.
Fix this by adding a "has_refsel" field, and setting the REFSEL based on
that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that we have the common DSS PLL support, change DSI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.
The functions to calculate and program the PLL settings can be removed
from dsi.c, as the common PLL API contains the same functionality.
We also need to create struct dss_pll_hw entries for PLL hardware
features for different OMAP platforms, instead of using the
dss_features.c as the old code does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP DSS currently contains two different PLLs: DSI PLL (Type A PLL) and
HDMI PLL (Type B PLL). When DRA7 support is added, we will also support
Video PLLs (Type A).
The driver currently handles all PLLs totally separately. This patch
adds common DSS PLL code, which
a) lets us have common code for the PLLs
b) lets the users of the PLLs use a common API, instead of DSI API or
HDMI API.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When DPI uses the DSI PLL for pixel clock, the DPI code will call
dsi_runtime_get/put to keep the DSI block enabled. A much simpler way to
handle this is to do dsi_runtime_get/put in DSI's dsi_pll_init() and
dsi_pll_uninit(), thus removing the need for DSI to call the runtime PM
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HSDIV outputs of DSI PLL (and also other PLLs) all have the same
bit width for the divider value.
Simplify the code by merging HSDIV divider widths into one width.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are creating a common DSS PLL code, so having fixed DSI specific
hsdiv fields in the clock information is not ok.
This patch changes the hsdiv fields to arrays, so that we can use all
the 4 possible hsdiv outputs (DSI only usees 2), and we have generic way
to access the hsdivs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are creating a common DSS PLL code, so rename 'clkin4ddr' field,
which is DSI specific name, to 'clkdco' which is a generic name.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that dsi_clock_info only contains information about the PLL, we can
just copy the whole struct when storing the clock information, instead
of copying individual fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have pll_locked field in struct dsi_data, but it doesn't have any
meaningful use anymore, and can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct dsi_clock_info contains clkin field, which is the rate of the
PLL's input clock. This field is not needed, as it can be easily
retrieved by using the clk_get_rate().
This patch removes the clkin field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
struct dsi_clock_info represents the clocks handled by the DSI, mostly
PLL related clocks. In an effort to create common PLL code, we need to
remove all the non-PLL items from dsi_clock_info.
This patch removes LP clock related fields from dsi_clock_info, and
creates a new struct dsi_lp_clock_info for holding clock info for the LP
clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSS PLL has support to power on the PLL's highspeed clock output
and HSDIV output separately. In practice both need to powered on, as in
most OMAP's that's the only working configuration. We already do that in
dsi_pll_init(), by overriding the passed arguments so that both are
always powered.
Simplify the code by removing the support for choosing which outputs to
power on.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
With the previous patch "OMAPDSS: DSI: wait for hsdiv clocks when
enabling PLL", dsi_wait_pll_hsdiv_dispc_active and
dsi_wait_pll_hsdiv_dsi_active are no longer needed, so they and the
callers can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At the moment we have two functions to wait for the HSDIV clocks to get
active, dsi_wait_pll_hsdiv_dispc_active and
dsi_wait_pll_hsdiv_dsi_active. Instead of such inconvenient functions,
let's just make sure that the hsdiv clocks are active after the pll has
been enabled.
This patch adds code to dsi_pll_set_clock_div() to wait until HSDIV
clocks are active.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a 'port' parameter in dpi_select_source. The param tells the port
number of the DPI instance that we want to configure. We use this number
to select the overlay manager for that DPI instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Register DPI outputs, and assign the port_num to them as specified by the
'reg' property in the DPI ports in DT.
To support multiple DPI instances, dpi_get_channel needs to take the DPI
instance's port number to get the corresponding channel. Make it take this
argument. We just pass 0 in the non-DT path, since we don't support multiple
instances in the non-DT case.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In omapdss_of_find_source_for_first_ep, we retrieve a source endpoint's DT node,
and then see what omapdss output has the matching device_node pointer in
omap_dss_find_output_by_node.
For all DPI and SDI outputs, the device_node pointer is set as the parent's DSS
device_node pointer. If the source is one of these outputs, the above method
won't work.
To get the correct output for ports within DSS(and in other cases in the future,
where multiple ports might be under one device), we require additional
information which is exclusive to the output port.
We create a new field in omap_dss_device called 'port_num', this provides port
number of the output port corresponding to this device. When searching for the
source endpoint in DT, we extract the 'reg' property from the port corresponding
to the endpoint source. From the list of registered outputs, we pick out that
output which has both dev->of_node and port_num matching with the device_node
pointer and 'reg' of the source endpoint node from DT.
For encoder blocks(the ones which have both an input and output port), we need
to set the port_num as the 'reg' property for the output port as defined in the
DT bindings. We set port_num to 1 in the tfp410 and tpd12s015 encoder drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The init/uninit port functions are used to set up the DPI and SDI outputs under
the dss platform device. A 'reg' property is used to determine the port number
of the output. This tells us whether the port is DPI or SDI for OMAP34xx DSS
revision. For other DSS revisions, we only have DPI outputs under the dss
platform device.
For multiple DPI output instances(introduced in DRA7xx DSS), we will use the
the port number to specify which DPI output instance is being inited.
The current functions work fine if there is only one DPI output instance in
DSS. For multiple DPI instances, it would get complicated to figure out whether
port number was used to specify whether the output is SDI, or another DPI
instance.
We create a list of port types supported for each DSS rev, with the index of the
port in the list specifying the port number of the output for that DSS revision.
This allows us to have a more generic way to init/uninit ports within DSS, and
also support multiple DPI ports.
We make the uninit_port functions iterative since we will have multiple DPI
ports to uninit in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI and SDI ports are backed by only one parent DSS device. We don't have a
corresponding platform_device for ports under DSS. In order to support multiple
instances of DPI, we need to pass the driver data pointer through the DPI port's
private data ('data' member in device_node struct).
dpi_init_output/dpi_uninit_output are untouched and only used for non-DT case,
these are called when the DPI platform device probed/removed. These funcs will
be removed when non-DT mode is removed.
dpi_init_output_port/dpi_uninit_output_port are created and used for the DT
path, called when DSS inits/uninits it's ports. These new functions retrieve
the dpi_data pointer from 'port->data', and not from the platform device's
data(pdev->dev) like in the non-DT path.
We add some code in dss_uninit_ports() to pass a pointer to the DPI port in
dpi_uninit_port().
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Allocate driver data(dpi_data) for each DPI instance. It's allocated in
omap_dpi_probe() when DT isn't used, and in dpi_init_port() when DT is used.
The dpi_data struct instance is no longer global. In the case of DPI ops, it's
retrieved from dpi_get_data_from_dssdev(). 'dssdev' passed by the connected
encoder/panel driver is a pointer to the 'output' member in dpi_data, and thus
can be used to get the DPI instance's driver data. In the case of probe/ini_port
functions, it's set as DPI/DSS device's private data embedded in the
platform_device struct.
Having dpi_data as private data of the platform device will not work for
multiple DPI instances in the DT case. This is because there is no corresponding
platform_device for DPI or SDI, they exist only as ports under the parent DSS
platform_device in the DT case. The DPI port's private data('data' member in
device_node struct) will later be used to store dpi_data.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI related data is currently a static global struct parameter. It is accessed
directly by functions in the driver.
This method won't work if we want the driver to support multiple DPI instances.
Create struct dpi_data, and pass its pointer to functions which need to use it.
We still have a static instance defined for dpi_data, which is accessed by top
level DPI ops. This will be removed when the driver dynamically allocates
dpi_data for each DPI instance.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If PWM device is requested by means of legacy API pwm_request(), its
resources are not freed on module unbind, which may cause an oops on
access, e.g. by reading /sys/kernel/debug/pwm.
Reported-by: Dmitry Eremin-Solenikov <dmitry_eremin@mentor.com>
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If no framebuffers found, sm501fb_probe() breaks off initialization,
deallocates sm501fb_info, but returns zero. As a result, use after free
can happen in sm501fb_remove().
The patch adds -ENODEV as a return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
mx6sl and mx6sx share the same LCD controller as mx23 and mx28.
Add support for it.
The basic difference is the number of clocks that are required:
- mx23/mx28: only one clock
- mx6sl: two clocks
- mx6sx: three clocks
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Without that fix connector-analog-tv driver isn't probed when compiled
as module.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
PLL_SELFREQDCO bitfield is from bit 3 to 1, but the driver writes bits
from 4 to 1. The bit 4 is 'reserved', so this probably should not cause
any issues, but it's better to fix it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Preload register is dumped twice for video overlays and mflag register
is not dumped for GFX.
Fix the register dump.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI PLL's REGSD field is only set by the driver if the PLL's output
clock is over 1GHz. This is clearly an error, as REGSD should be set
always.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The PLL settings are committed by setting GO bit, which is then cleared
by the HW when the settings have been taken into use.
The current PLL code handles this wrong: instead of waiting for the bit
to be cleared, it waits for the bit to be set. Usually, the bit is
always set, as the CPU has just set it before. However, if the CPU takes
enough time between setting the GO bit and checking it, the HW may
already have cleared the bit and this leads to timeout error.
Fix the wait to check the bit properly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb disables all the overlays when freeing resources, but it should
also remove those overlays from overlay managers.
Not doing so causes a crash if omapfb is unbound and bound, or omapfb
module is removed and loaded, while keeping omapdss around.
Fix this by calling unset_manager() for all overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When omapfb is shutting down, it will disable all the overlays. However,
instead of actually disabling all the overlays, it disables only all the
overlays that are currently attached to framebuffers.
On OMAP4+, this leaves the fourth overlay left enabled.
Fix the loop so that we actually go through all the overlays.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We should wait for any pending updates when an overlay manager is
about to be disabled, because the updates will never be finished if the
manager is disabled too early.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we leave __exit annotation, driver can't be unbound
through sysfs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss drivers cannot handle devices being unbound while the devices
are part of a connected display pipeline. Module refcounts are used to
prevent unloading the modules, but one can still manually unbind the
devices via sysfs, causing crash.
Set suppress_bind_attrs to disable the bind/unbind support via sysfs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
without MODULE_ALIAS(), omapfb won't get loaded
automatically.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove unnecessary mach/cpu.h header to be able to converge to a multiplatform
kernel.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Resolve shadow warnings that appear in W=2 builds by renaming
the "state" global to "vgastate".
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since strsep is used to tokenize the options string, after each option
match the code should use "continue" to get the next token from strsep.
This patch applies this pattern consistently.
Previously, for "scrollback:" and "map:" the parse code would return
(unconditionally: strsep ensures *options != ','), causing any
following option to be ignored, while for "vc:" the parse code would
go on to parse further options within the same token, which could lead
to invalid input being accepted.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
* new 6x10 font
* various small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f13d
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- new 6x10 font
- various small fixes and cleanups
* tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (30 commits)
fonts: Add 6x10 font
videomode: provide dummy inline functions for !CONFIG_OF
video/atmel_lcdfb: Introduce regulator support
fbdev: sh_mobile_hdmi: Re-init regs before irq re-enable on resume
framebuffer: fix screen corruption when copying
framebuffer: fix border color
arm, fbdev, omap2, LLVMLinux: Remove nested function from omapfb
arm, fbdev, omap2, LLVMLinux: Remove nested function from omap2 dss
video: fbdev: valkyriefb.c: use container_of to resolve fb_info_valkyrie from fb_info
video: fbdev: pxafb.c: use container_of to resolve pxafb_info/layer from fb_info
video: fbdev: cyber2000fb.c: use container_of to resolve cfb_info from fb_info
video: fbdev: controlfb.c: use container_of to resolve fb_info_control from fb_info
video: fbdev: sa1100fb.c: use container_of to resolve sa1100fb_info from fb_info
video: fbdev: stifb.c: use container_of to resolve stifb_info from fb_info
video: fbdev: sis: sis_main.c: Cleaning up missing null-terminate in conjunction with strncpy
video: valkyriefb: Fix unused variable warning in set_valkyrie_clock()
video: fbdev: use %*ph specifier to dump small buffers
video: mx3fb: always enable BACKLIGHT_LCD_SUPPORT
video: fbdev: au1200fb: delete double assignment
video: fbdev: sis: delete double assignment
...
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull drm updates from Dave Airlie:
"This is the main git pull for the drm,
I pretty much froze major pulls at -rc5/6 time, and haven't had much
fallout, so will probably continue doing that.
Lots of changes all over, big internal header cleanup to make it clear
drm features are legacy things and what are things that modern KMS
drivers should be using. Also big move to use the new generic fences
in all the TTM drivers.
core:
atomic prep work,
vblank rework changes, allows immediate vblank disables
major header reworking and cleanups to better delinate legacy
interfaces from what KMS drivers should be using.
cursor planes locking fixes
ttm:
move to generic fences (affects all TTM drivers)
ppc64 caching fixes
radeon:
userptr support,
uvd for old asics,
reset rework for fence changes
better buffer placement changes,
dpm feature enablement
hdmi audio support fixes
intel:
Cherryview work,
180 degree rotation,
skylake prep work,
execlist command submission
full ppgtt prep work
cursor improvements
edid caching,
vdd handling improvements
nouveau:
fence reworking
kepler memory clock work
gt21x clock work
fan control improvements
hdmi infoframe fixes
DP audio
ast:
ppc64 fixes
caching fix
rcar:
rcar-du DT support
ipuv3:
prep work for capture support
msm:
LVDS support for mdp4, new panel, gpu refactoring
exynos:
exynos3250 SoC support, drop bad mmap interface,
mipi dsi changes, and component match support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (640 commits)
drm/mst: rework payload table allocation to conform better.
drm/ast: Fix HW cursor image
drm/radeon/kv: add uvd/vce info to dpm debugfs output
drm/radeon/ci: add uvd/vce info to dpm debugfs output
drm/radeon: export reservation_object from dmabuf to ttm
drm/radeon: cope with foreign fences inside the reservation object
drm/radeon: cope with foreign fences inside display
drm/core: use helper to check driver features
drm/radeon/cik: write gfx ucode version to ucode addr reg
drm/radeon/si: print full CS when we hit a packet 0
drm/radeon: remove unecessary includes
drm/radeon/combios: declare legacy_connector_convert as static
drm/radeon/atombios: declare connector convert tables as static
drm/radeon: drop btc_get_max_clock_from_voltage_dependency_table
drm/radeon/dpm: drop clk/voltage dependency filters for BTC
drm/radeon/dpm: drop clk/voltage dependency filters for CI
drm/radeon/dpm: drop clk/voltage dependency filters for SI
drm/radeon/dpm: drop clk/voltage dependency filters for NI
drm/radeon: disable audio when we disable hdmi (v2)
drm/radeon: split audio enable between eg and r600 (v2)
...
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
- Checkpatch fixes
- Removal of unused code in generic_bl
- Removal of superfluous .owner attribute
New drivers/supported devices
- None
(Re-)moved drivers
- None
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWUv
-----END PGP SIGNATURE-----
Merge tag 'backlight-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight driver updates from Lee Jones:
"Changes to existing drivers:
- Checkpatch fixes
- Removal of unused code in generic_bl
- Removal of superfluous .owner attribute
No new or removed drivers/supported devices"
* tag 'backlight-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: omap1: add blank line after declarations
backlight: jornada720: Remove 'else' after a return
backlight: jornada720: Remove 'else' after a return
backlight: wm831x_bl: Add blank line after declarations
backlight: tdo24m: Add blank line after declarations
backlight: s6e63m0: Remove 'else' after a return
backlight: pcf50633: Add blank line after declarations
backlight: lp855x: Add blank line after declarations
backlight: lms501kf03: Remove 'else' after a return
backlight: lm3639: Remove unnecessary return statements
backlight: ld9040: Remove 'else' after a return
backlight: ili922x: Remove 'else' after a return
backlight: cr_bllcd: Add blank line after declarations
backlight: corgi_lcd: Add blank line after declarations
backlight: ams369fg06: Remove 'else' after a return
backlight: adp8870: Add blank line after declarations
backlight: adp8860: Add blank line after declarations
backlight: adp5520: Add blank line after declarations
backlight: generic_bl: Remove unused function
backlight: Remove .owner field for drivers using module_platform_driver
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
This adds regulator support to enable/disable the LCD voltage, using
'lcd-supply' as regulator name.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When the PM domain containing the HDMI hardware block is powered down,
the HDMI register values (incl. interrupt polarity settings) are lost.
During resume, after powering up the PM domain, interrupts are
re-enabled, and an interrupt storm happens due to incorrect interrupt
polarity settings:
irq 163: nobody cared (try booting with the "irqpoll" option)
...
Disabling IRQ #163
To fix this, re-initialize the interrupt polarity settings, and the
htop1 register block (if present), during resume.
As the .suspend_noirq() and .resume_noirq() callbacks are not called
when using the generic PM domain, the normal .resume() callback is used,
and the device interrupt needs to be disabled/enabled manually.
This fixes resume from s2ram with power down of the A4MP PM domain on
r8a7740/Armadillo.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function bitcpy_rev has a bug that may result in screen corruption.
The bug happens under these conditions:
* the end of the destination area of a copy operation is aligned on a long
word boundary
* the end of the source area is not aligned on a long word boundary
* we are copying more than one long word
In this case, the variable shift is non-zero and the variable first is
zero. The statements FB_WRITEL(comp(d0, FB_READL(dst), first), dst) reads
the last long word of the destination and writes it back unchanged
(because first is zero). Correctly, we should write the variable d0 to the
last word of the destination in this case.
This patch fixes the bug by introducing and extra test if first is zero.
The patch also removes the references to fb_memmove in the code that is
commented out because fb_memmove was removed from framebuffer subsystem.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The framebuffer code uses the current background color to fill the border
when switching consoles, however, this results in inconsistent behavior.
For example:
- start Midnigh Commander
- the border is black
- switch to another console and switch back
- the border is cyan
- type something into the command line in mc
- the border is cyan
- switch to another console and switch back
- the border is black
- press F9 to go to menu
- the border is black
- switch to another console and switch back
- the border is dark blue
When switching to a console with Midnight Commander, the border is random
color that was left selected by the slang subsystem.
This patch fixes this inconsistency by always using black as the
background color when switching consoles.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace the use of nested functions where a normal function will suffice.
Nested functions are not liked by upstream kernel developers in general. Their
use breaks the use of clang as a compiler, and doesn't make the code any
better.
This code now works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
The DT-based panel capabilities selection was picking up
a subset of available modes based on hardware configuration.
This was wrong, as the capabilities describe available
memory models and adapt the display controller to them
that the RGB output is wired up correctly (as in: R and
B components are not swapped).
This patch fixes it by removing the unnecessary limitation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of dereference each byte let's use %*ph specifier in the printk()
calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 7edaa761ee ("video: mx3fb: Add backlight control support")
changed the mx3fb driver so it always selects the BACKLIGHT_CLASS_DEVICE
symbol, but that is hidden behind BACKLIGHT_LCD_SUPPORT in Kconfig, so
we get a Kconfig warning for multi_v5_defconfig, which doesn't have that:
Warning: (DRM_RADEON && DRM_NOUVEAU && DRM_I915 && DRM_GMA500 &&
DRM_SHMOBILE && DRM_TILCDC && FB_BACKLIGHT && FB_MX3 && USB_APPLEDISPLAY
&& FB_OLPC_DCON && ASUS_LAPTOP && SONY_LAPTOP && THINKPAD_ACPI &&
EEEPC_LAPTOP && ACPI_CMPC && SAMSUNG_Q10) selects BACKLIGHT_CLASS_DEVICE
which has unmet direct dependencies (HAS_IOMEM && BACKLIGHT_LCD_SUPPORT)
This makes sure we always enable both symbols together for mx3fb, like
we do for the other drivers that can't be built without backlight
support. Note that a better solution would be to ensure the driver can
work with or without backlight support.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: void function return statements are not generally useful
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: else is not generally useful after a break or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixed the following checkpatch warning.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
genericbl_limit_intensity() is exported, but it is never
called anywhere else.
Fix the following sparse warning:
drivers/video/backlight/generic_bl.c:59:6:
warning: symbol 'genericbl_limit_intensity' was not declared.
Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver or platform_driver_register api,
as this is overriden in __platform_driver_register.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Delete successive assignments to the same location. The second assignment
is changed to update a different field, as done in other nearby code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Delete successive assignments to the same location.
In the second case, = is converted to |=, which looks appropriate based on
the values involved.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move to managed verion of kzalloc. Also checks return for failure case
which was missing.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stephen Boyd <sboyd@codeaurora.org>
CC: Jingoo Han <jg1.han@samsung.com>
CC: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This adds a remove function to platform driver structure so that
resources are released when driver is unloaded.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stephen Boyd <sboyd@codeaurora.org>
CC: Jingoo Han <jg1.han@samsung.com>
CC: Rob Clark <robdclark@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 16052827d9 ("dmaengine/dma_slave:
introduce inline wrappers") changed the code to use the new API, but forgot
to update a comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-fbdev@vger.kernel.org
--
v2:
- New
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use c99 initializers for structures.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use c99 initializers for structures.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use c99 initializers for structures.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Of_node_put supports NULL as its argument, so the initial test is not
necessary. Furthermore, native_mode cannot be NULL at this point.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When looking at this driver for a client, I noticed the code that
configures the HSYNC pulse clobbers the display width in the same
register. It only preserves the MS part of the width in bit 3 and zeros
the LS part of the width in bits 9 to 4. This doesn't matter during
initialization as the width is configured afterwards, but subsequent use
of the FBIPUT_HSYNC ioctl would clobber the width.
Preserve bits 9 to 0 of LCD_RASTER_TIMING_0_REG when configuring the
horizontal sync.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display_timings_release() function frees "disp" and we free it
again on the next line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the device-tree specifies a max-memory-bandwidth property then the
CLCD driver uses that to calculate the bits-per-pixel supported,
however, this calculation is faulty for two reasons.
1. It doesn't ensure that the result is a sane value, i.e. a power of 2
and <= 32 as the rest of the code assumes.
2. It uses the displayed resolution and calculates the average bandwidth
across the whole frame. It should instead calculate the peak
bandwidth based on the pixel clock.
This patch fixes both the above.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix build failure caused as follows:
The function chipsfb_pci_init() references
the function __init chips_hw_init().
This is often because chipsfb_pci_init lacks a __init
annotation or the annotation of chips_hw_init is wrong.
make: *** [drivers] Error 2
by removing the __init annotation from chips_hw_init(). The other thing that
could have been done was annotating chipsfb_pci_init(). But that cannot be done
since chipsfb_pci_init() is called from non __init functions.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
So small drm stuff all over for 3.18. Biggest one is the cmdline parsing
from Chris with a few fixes from me to make it work for stupid kernel
configs.
Plus the atomic prep series.
Tested for more than a week in -nightly and Ville/Imre indeed discovered
some fun which is now fixed (and i915 vblank patches postponed since the
fixups need this branch plus drm-intel-next merged together).
* tag 'topic/core-stuff-2014-08-15' of git://anongit.freedesktop.org/drm-intel:
drm: Use the type of the array element when reallocating
drm: Don't return 0 for a value used as a denominator
drm: Docbook fixes
drm/irq: Implement a generic vblank_wait function
drm: Add a plane->reset hook
drm: trylock modest locking for fbdev panics
drm: Move ->old_fb from crtc to plane
drm: Handle legacy per-crtc locking with full acquire ctx
drm: Move modeset_lock_all helpers to drm_modeset_lock.[hc]
drm: Add drm_plane/connector_index
drm: idiot-proof vblank
drm: Warn when leaking flip events on close
drm: Perform cmdline mode parsing during connector initialisation
video/fbdev: Always built-in video= cmdline parsing
drm: Don't grab an fb reference for the idr
commit 257462dbf3 ("pwm-backlight: switch to gpiod interface")
introduced a regression leading to acquiring a bogus GPIO-0 when
configured from DT without an 'enable-gpios' property.
The driver will happily accept the 0 initialized 'enable_gpio' member
of the struct platform_pwm_backlight_data as valid gpio number, and
request this GPIO as enable pin. In case of multiple driver instances,
the second will fail to register with the error message:
pwm-backlight backlight1.23: failed to request GPIO#0: -16
Fix this by setting enable_gpio in the pdata struct to -EINVAL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* Much better HDMI infoframe support for OMAP
* Cirrus Logic CLPS711X framebuffer driver
* DT support for PL11x CLCD driver
* Various small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gXX+
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
After v3.16-rc1, devices populated with of_platform_populate() should be
depopulated using of_platform_depopulate(). Failure to do so prevents
the devices from being populated again (e.g. when loading a module).
This patch fixes the problem for the OMAP DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
In drm/i915 we want to get at the video= cmdline modes even when we
don't have fbdev support enabled, so that users can always override
the kernel's initial mode selection.
But that gives us a direct depency upon the parsing code in the fbdev
subsystem. Since it's so little code just extract these 2 functions
and always build them in.
Whiel at it fix the checkpatch fail in this code.
v2: Also move fb_mode_option. Spotted by the kbuild.
v3: Review from Geert:
- Keep the old copyright notice from fb_mem.c, although I have no
idea what exactly applies.
- Only compile this when needed.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
--
I prefer if we can merge this through drm-next since we'll use it
there in follow-up patches.
-Daniel
We don't want random users to be able to spam the logs, and commit
37549e94c7 (sysfs: disallow
world-writable files.) finally makes this a build error.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently the VSC has no chance to notify the VSP of the dirty rectangle on VM
panic because the notification work is done in a workqueue, and in panic() the
kernel typically ends up in an infinite loop, and a typical kernel config has
CONFIG_PREEMPT_VOLUNTARY=y and CONFIG_PREEMPT is not set, so a context switch
can't happen in panic() and the workqueue won't have a chance to run. As a
result, the VM Connection window can't refresh until it's closed and we
re-connect to the VM.
We can register a handler on panic_notifier_list: the handler can notify
the VSC and switch the framebuffer driver to a "synchronous mode", meaning
the VSC flushes any future framebuffer change to the VSP immediately.
v2: removed the MS-TFS line in the commit message
v3: remove some 'unlikely' markings
v4: avoid global variables as Tomi Valkeinen suggested
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch fixes the following error when !CONFIG_OF:
drivers/video/fbdev/amba-clcd.c:800:54: warning: ‘struct amba_dev’ declared inside parameter list [enabled by default]
static struct clcd_board *clcdfb_of_get_board(struct amba_dev *dev)
^
and adds a missing Kconfig select causing this
when CONFIG_OF && !CONFIG_FB_MODE_HELPERS:
drivers/video/fbdev/amba-clcd.c:567: undefined reference to `fb_videomode_from_videomode'
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Peter Meerwald