We are about to add an entry flush. The rfi (exit) flush test measures
the number of L1D flushes over a syscall with the RFI flush enabled and
disabled. But if the entry flush is also enabled, the effect of enabling
and disabling the RFI flush is masked.
If there is a debugfs entry for the entry flush, disable it during the RFI
flush and restore it later.
Reported-by: Spoorthy S <spoorts2@in.ibm.com>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_PCI=n leads to a compile warning like:
sound/pci/hda/patch_ca0132.c:8214:10: warning: no case matching constant switch condition '0'
due to the missed handling of QUIRK_NONE in ca0132_mmio_init().
Fix it.
Fixes: bf2aa9ccc8 ("ALSA: hda/ca0132 - Cleanup ca0132_mmio_init function.")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201119120404.16833-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Joerg is recovering from an injury, so temporarily add myself to the
IOMMU MAINTAINERS entry so that I'm more likely to get CC'd on patches
while I help to look after the tree for him.
Suggested-by: Joerg Roedel <joro@8bytes.org>
Link: https://lore.kernel.org/r/20201117100953.GR22888@8bytes.org
Signed-off-by: Will Deacon <will@kernel.org>
Fix the compile error below (CONFIG_PCI_ATS not set):
drivers/iommu/intel/dmar.c: In function ‘vf_inherit_msi_domain’:
drivers/iommu/intel/dmar.c:338:59: error: ‘struct pci_dev’ has no member named ‘physfn’; did you mean ‘is_physfn’?
338 | dev_set_msi_domain(&pdev->dev, dev_get_msi_domain(&pdev->physfn->dev));
| ^~~~~~
| is_physfn
Fixes: ff828729be ("iommu/vt-d: Cure VF irqdomain hickup")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/linux-iommu/CAMuHMdXA7wfJovmfSH2nbAhN0cPyCiFHodTvg4a8Hm9rx5Dj-w@mail.gmail.com/
Link: https://lore.kernel.org/r/20201119055119.2862701-1-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
- Cure the fallout from the MSI irqdomain overhaul which missed that the
Intel IOMMU does not register virtual function devices and therefore
never reaches the point where the MSI interrupt domain is assigned. This
makes the VF devices use the non-remapped MSI domain which is trapped by
the IOMMU/remap unit.
- Remove an extra space in the SGI_UV architecture type procfs output for
UV5.
- Remove a unused function which was missed when removing the UV BAU TLB
shootdown handler.
-----BEGIN PGP SIGNATURE-----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=X/P+
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into for-next/iommu/fixes
Pull in x86 fixes from Thomas, as they include a change to the Intel DMAR
code on which we depend:
* tag 'x86-urgent-2020-11-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
iommu/vt-d: Cure VF irqdomain hickup
x86/platform/uv: Fix copied UV5 output archtype
x86/platform/uv: Drop last traces of uv_flush_tlb_others
This patch is a preliminary fix that will conflict with subsequent work merged
through arm-soc.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX7TgqQAKCRDj7w1vZxhR
xSyOAQDMT7xST/1bfkftNIoXgyF0El6aFU3IdMs57saTWk5A5AEAtWjAHkjADj1p
sg7gAHY+hYVullCSr92wsX+67APFFA4=
=U7c/
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCX7YsHwAKCRDj7w1vZxhR
xaFCAQCmRKxe0yIFn9VjcCn1hgK6d9tqQXquRTntwswidFnDjQEApLSdKkeTARrU
+D90lDMJ+UoWoKBGpF9LFxdL+SFvSQ8=
=Cod1
-----END PGP SIGNATURE-----
Merge tag 'drm/sun4i-dma-fix-pull-request' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mripard/linux into drm-misc-fixes
Fix for drm/sun4i shared with arm-soc
This patch is a preliminary fix that will conflict with subsequent work merged
through arm-soc.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
# gpg: Signature made Wed 18 Nov 2020 09:51:53 AM CET
# gpg: using EDDSA key 5C1337A45ECA9AEB89060E9EE3EF0D6F671851C5
# gpg: Good signature from "Maxime Ripard <maxime.ripard@anandra.org>" [unknown]
# gpg: aka "Maxime Ripard <mripard@kernel.org>" [unknown]
# gpg: aka "Maxime Ripard (Work Address) <maxime.ripard@bootlin.com>" [unknown]
# gpg: aka "Maxime Ripard (Work Address) <maxime@bootlin.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: BE56 75C3 7E81 8C8B 5764 241C 254B CFC5 6BF6 CE8D
# Subkey fingerprint: 5C13 37A4 5ECA 9AEB 8906 0E9E E3EF 0D6F 6718 51C5
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118090455.sznrgpduuytlc22k@gilmour.lan
Since we allocate some breadcrumbs for the virtual engine, and the
virtual engine has a custom destructor, we also need to free the
breadcrumbs after use.
Fixes: b3786b2937 ("drm/i915/gt: Distinguish the virtual breadcrumbs from the irq breadcrumbs")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201118133839.1783-1-chris@chris-wilson.co.uk
(cherry picked from commit 45e50f48b7)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
EDID can declare the maximum supported bpc up to 16,
and apparently there are displays that do so. Currently
we assume 12 bpc is tha max. Fix the assumption and
toss in a MISSING_CASE() for any other value we don't
expect to see.
This fixes modesets with a display with EDID max bpc > 12.
Previously any modeset would just silently fail on platforms
that didn't otherwise limit this via the max_bpc property.
In particular we don't add the max_bpc property to HDMI
ports on gmch platforms, and thus we would see the raw
max_bpc coming from the EDID.
I suppose we could already adjust this to also allow 16bpc,
but seeing as no current platform supports that there is
little point.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2632
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110210447.27454-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 2ca5a7b85b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAl+1QxwTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqVKjB/wO4VxhYVsszeJTTqO2KmQA/v0EkPUq
+bUlA8Zew1D9x7YkRT9bf3vt7UxGCIMG4hqIRIt9ktK6gc6HIvqvTSIEDZXTs6N5
dFtY7+YEezSpDYo5Z9tzsBrMTH7JGGqRPjlHuKJkPoTWJ5UYqGQcrsXqZvOVD2t8
hKNtV0loaTrAv1d68I5IP+Yk/OCFeIHdg/WBArJ1BxXgsPhN1kpb3Zr8wj1yVIVu
7je9sJ5FheNEPtR+rJOKbRlJl+s2Qn3tubnz0rsbJzbThsBS3tTmY27XKQ7yWvRX
BdmuQgm9dfx/glHvZDRCnUKvlWka+CopLT8RTkK3B3o2E04aIZuSdPAl
=PDPZ
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.10-20201118' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-18
Jimmy Assarsson provides two patches for the kvaser_pciefd and kvaser_usb
drivers, where the can_bittiming_const are fixed.
The next patch is by me and fixes an erroneous flexcan_transceiver_enable()
during bus-off recovery in the flexcan driver.
Jarkko Nikula's patch for the m_can driver fixes the IRQ handler to only
process the interrupts if the device is not suspended.
* tag 'linux-can-fixes-for-5.10-20201118' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: process interrupt only when not runtime suspended
can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery
can: kvaser_usb: kvaser_usb_hydra: Fix KCAN bittiming limits
can: kvaser_pciefd: Fix KCAN bittiming limits
====================
Link: https://lore.kernel.org/r/20201118160414.2731659-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded6043 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl+0KZ4ACgkQSD+KveBX
+j5DDAgAip1LGfOUq7RISh1OWQ9zLl2KT/mmbdSioObGgjKunU4lMGZAPrLB0bpe
RH1RodslY+1bepcz7VQ/QxbL0EU605SZn08xLZIQAYYXT0Sar+hhg7h7vhD0iSA1
dwDF/XLQYHf8snc3x/tu6/zp9BzfzRfuiieYAbC1ri97Iz9uoYO+QcRI7OyqgXWf
LmK9/s6WzgaC0DKg8XXEQGp7F1MbZfJph6tThZnF62NY9Rrkut6AEah85p1QaqF7
9WLjqOtJwo893fzbN+WCXJTYo2UX9oU18nUSvSoYid2LEofiwY3PcT8R0gKSPZto
cVcjm1oGsotbonBnPlR2eMZq8LdPDQ==
=MKi5
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-11-17
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: fix error return code in mlx5e_tc_nic_init()
net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled
net/mlx5: Disable QoS when min_rates on all VFs are zero
net/mlx5: Clear bw_share upon VF disable
net/mlx5: Add handling of port type in rule deletion
net/mlx5e: Fix check if netdev is bond slave
net/mlx5e: Fix IPsec packet drop by mlx5e_tc_update_skb
net/mlx5e: Set IPsec WAs only in IP's non checksum partial case.
net/mlx5e: Fix refcount leak on kTLS RX resync
====================
Link: https://lore.kernel.org/r/20201117195702.386113-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The `skb' is mapped for DMA in ns_send() but does not unmap DMA in case
push_scqe() fails to submit the `skb'. The memory of the `skb' is
released so only the DMA mapping is leaking.
Unmap the DMA mapping in case push_scqe() failed.
Fixes: 864a3ff635 ("atm: [nicstar] remove virt_to_bus() and support 64-bit platforms")
Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ethernet driver may allocate skb (and skb->data) via napi_alloc_skb().
This ends up to page_frag_alloc() to allocate skb->data from
page_frag_cache->va.
During the memory pressure, page_frag_cache->va may be allocated as
pfmemalloc page. As a result, the skb->pfmemalloc is always true as
skb->data is from page_frag_cache->va. The skb will be dropped if the
sock (receiver) does not have SOCK_MEMALLOC. This is expected behaviour
under memory pressure.
However, once kernel is not under memory pressure any longer (suppose large
amount of memory pages are just reclaimed), the page_frag_alloc() may still
re-use the prior pfmemalloc page_frag_cache->va to allocate skb->data. As a
result, the skb->pfmemalloc is always true unless page_frag_cache->va is
re-allocated, even if the kernel is not under memory pressure any longer.
Here is how kernel runs into issue.
1. The kernel is under memory pressure and allocation of
PAGE_FRAG_CACHE_MAX_ORDER in __page_frag_cache_refill() will fail. Instead,
the pfmemalloc page is allocated for page_frag_cache->va.
2: All skb->data from page_frag_cache->va (pfmemalloc) will have
skb->pfmemalloc=true. The skb will always be dropped by sock without
SOCK_MEMALLOC. This is an expected behaviour.
3. Suppose a large amount of pages are reclaimed and kernel is not under
memory pressure any longer. We expect skb->pfmemalloc drop will not happen.
4. Unfortunately, page_frag_alloc() does not proactively re-allocate
page_frag_alloc->va and will always re-use the prior pfmemalloc page. The
skb->pfmemalloc is always true even kernel is not under memory pressure any
longer.
Fix this by freeing and re-allocating the page instead of recycling it.
References: https://lore.kernel.org/lkml/20201103193239.1807-1-dongli.zhang@oracle.com/
References: https://lore.kernel.org/linux-mm/20201105042140.5253-1-willy@infradead.org/
Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Cc: Bert Barbe <bert.barbe@oracle.com>
Cc: Rama Nichanamatlu <rama.nichanamatlu@oracle.com>
Cc: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Cc: Manjunath Patil <manjunath.b.patil@oracle.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: SRINIVAS <srinivas.eeda@oracle.com>
Fixes: 79930f5892 ("net: do not deplete pfmemalloc reserve")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20201115201029.11903-1-dongli.zhang@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We recently improved our display atomic commit and tail sequence to
avoid some issues related to concurrency. One of the major changes
consisted of moving the interrupt disable and the stream release from
our atomic commit to our atomic tail (commit 6d90a208cf
("drm/amd/display: Move disable interrupt into commit tail")) .
However, the new code introduced inside our commit tail function was
inserted right after the function
drm_atomic_helper_update_legacy_modeset_state(), which has routines for
updating internal data structs related to timestamps. As a result, in
certain conditions, the display module can reach a situation where we
update our constants and, after that, clean it. This situation generates
the following warning:
amdgpu 0000:03:00.0: drm_WARN_ON_ONCE(drm_drv_uses_atomic_modeset(dev))
WARNING: CPU: 6 PID: 1269 at drivers/gpu/drm/drm_vblank.c:722
drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x32b/0x340 [drm]
...
RIP:
0010:drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x32b/0x340
[drm]
...
Call Trace:
? dc_stream_get_vblank_counter+0x57/0x60 [amdgpu]
drm_crtc_vblank_helper_get_vblank_timestamp+0x1c/0x20 [drm]
drm_get_last_vbltimestamp+0xad/0xc0 [drm]
drm_reset_vblank_timestamp+0x63/0xd0 [drm]
drm_crtc_vblank_on+0x85/0x150 [drm]
amdgpu_dm_atomic_commit_tail+0xaf1/0x2330 [amdgpu]
commit_tail+0x99/0x130 [drm_kms_helper]
drm_atomic_helper_commit+0x123/0x150 [drm_kms_helper]
amdgpu_dm_atomic_commit+0x11/0x20 [amdgpu]
drm_atomic_commit+0x4a/0x50 [drm]
drm_atomic_helper_set_config+0x7c/0xc0 [drm_kms_helper]
drm_mode_setcrtc+0x20b/0x7e0 [drm]
? tomoyo_path_number_perm+0x6f/0x200
? drm_mode_getcrtc+0x190/0x190 [drm]
drm_ioctl_kernel+0xae/0xf0 [drm]
drm_ioctl+0x245/0x400 [drm]
? drm_mode_getcrtc+0x190/0x190 [drm]
amdgpu_drm_ioctl+0x4e/0x80 [amdgpu]
__x64_sys_ioctl+0x91/0xc0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xa9
...
For fixing this issue we rely upon a refactor introduced on
drm_atomic_helper_update_legacy_modeset_state ("Remove the timestamping
constant update from drm_atomic_helper_update_legacy_modeset_state()")
which decouples constant values update from
drm_atomic_helper_update_legacy_modeset_state to a new helper.
Basically, this commit uses this new helper and place it right after our
release module to avoid a situation where our CRTC struct gets wrong
values.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1373
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1349
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=R7xS
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.10-2' of git://linux-nfs.org/~bfields/linux
Pull nfsd fix from Bruce Fields:
"Just one quick fix for a tracing oops"
* tag 'nfsd-5.10-2' of git://linux-nfs.org/~bfields/linux:
SUNRPC: Fix oops in the rpc_xdr_buf event class
This Kunit update for Linux 5.10-rc5 consists of several fixes Kunit
documentation, tool, compile time fixes not pollute source directory,
and fix to remove tools/testing/kunit/.gitattributes file.
-----BEGIN PGP SIGNATURE-----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=mGWU
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-kunit-fixes-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kunit fixes from Shuah Khan:
"Several fixes to Kunit documentation and tools, and to not pollute
the source directory.
Also remove the incorrect kunit .gitattributes file"
* tag 'linux-kselftest-kunit-fixes-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: fix display of failed expectations for strings
kunit: tool: fix extra trailing \n in raw + parsed test output
kunit: tool: print out stderr from make (like build warnings)
KUnit: Docs: usage: wording fixes
KUnit: Docs: style: fix some Kconfig example issues
KUnit: Docs: fix a wording typo
kunit: Do not pollute source directory with generated files (test.log)
kunit: Do not pollute source directory with generated files (.kunitconfig)
kunit: tool: fix pre-existing python type annotation errors
kunit: Fix kunit.py parse subcommand (use null build_dir)
kunit: tool: unmark test_data as binary blobs
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
mlxsw: Couple of fixes
Patch #1 fixes firmware flashing when CONFIG_MLXSW_CORE=y and
CONFIG_MLXFW=m.
Patch #2 prevents EMAD transactions from needlessly failing when the
system is under heavy load by using exponential backoff.
Please consider patch #2 for stable.
====================
Link: https://lore.kernel.org/r/20201117173352.288491-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver sends Ethernet Management Datagram (EMAD) packets to the
device for configuration purposes and waits for up to 200ms for a reply.
A request is retried up to 5 times.
When the system is under heavy load, replies are not always processed in
time and EMAD transactions fail.
Make the process more robust to such delays by using exponential
backoff. First wait for up to 200ms, then retransmit and wait for up to
400ms and so on.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Reported-by: Denis Yulevich <denisyu@nvidia.com>
Tested-by: Denis Yulevich <denisyu@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit cited below moved firmware flashing functionality from
mlxsw_spectrum to mlxsw_core, but did not adjust the Kconfig
dependencies. This makes it possible to have mlxsw_core as built-in and
mlxfw as a module. The mlxfw code is therefore not reachable from
mlxsw_core and firmware flashing fails:
# devlink dev flash pci/0000:01:00.0 file mellanox/mlxsw_spectrum-13.2008.1310.mfa2
devlink answers: Operation not supported
Fix by having mlxsw_core select mlxfw.
Fixes: b79cb787ac ("mlxsw: Move fw flashing code into core.c")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Vadim Pasternak <vadimp@nvidia.com>
Tested-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA network devices rely on having their DSA management interface up and
running otherwise their ndo_open() will return -ENETDOWN. Without doing
this it would not be possible to use DSA devices as netconsole when
configured on the command line. These devices also do not utilize the
upper/lower linking so the check about the netpoll device having upper
is not going to be a problem.
The solution adopted here is identical to the one done for
net/ipv4/ipconfig.c with 728c02089a ("net: ipv4: handle DSA enabled
master network devices"), with the network namespace scope being
restricted to that of the process configuring netpoll.
Fixes: 04ff53f96a ("net: dsa: Add netconsole support")
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201117035236.22658-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: a6a5325239 ("atl1e: Atheros L1E Gigabit Ethernet driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581875-36281-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 43250ddd75 ("atl1c: Atheros L1C Gigabit Ethernet driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581721-36028-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605581105-35295-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LTE module MR400 embedded in TL-MR6400 v4 requires DTR to be set.
Signed-off-by: Filip Moc <dev@moc6.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20201117173631.GA550981@moc6.cz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
At the start of driver initialization, we do not know what bias
setting the bootloader has configured the system for and we only know
for certain the very first time we do a transition.
However, since the initial value of the comparison index is -EINVAL,
this negative value results in an array out of bound access on the
very first transition.
Since we don't know what the setting is, we just set the bias
configuration as there is nothing to compare against. This prevents
the array out of bound access.
NOTE: Even though we could use a more relaxed check of "< 0" the only
valid values(ignoring cosmic ray induced bitflips) are -EINVAL, 0+.
Fixes: 40b1936efe ("regulator: Introduce TI Adaptive Body Bias(ABB) on-chip LDO driver")
Link: https://lore.kernel.org/linux-mm/CA+G9fYuk4imvhyCN7D7T6PMDH6oNp6HDCRiTUKMQ6QXXjBa4ag@mail.gmail.com/
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20201118145009.10492-1-nm@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In kabylake_set_bias_level(), enabling mclk may fail if the clock has
already been enabled by the firmware. Attempts to disable that clock
later will fail with a warning backtrace.
mclk already disabled
WARNING: CPU: 2 PID: 108 at drivers/clk/clk.c:952 clk_core_disable+0x1b6/0x1cf
...
Call Trace:
clk_disable+0x2d/0x3a
kabylake_set_bias_level+0x72/0xfd [snd_soc_kbl_rt5663_rt5514_max98927]
snd_soc_card_set_bias_level+0x2b/0x6f
snd_soc_dapm_set_bias_level+0xe1/0x209
dapm_pre_sequence_async+0x63/0x96
async_run_entry_fn+0x3d/0xd1
process_one_work+0x2a9/0x526
...
Only disable the clock if it has been enabled.
Fixes: 15747a8020 ("ASoC: eve: implement set_bias_level function for rt5514")
Cc: Brent Lu <brent.lu@intel.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201111205434.207610-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
In xfs_initialize_perag(), if kmem_zalloc(), xfs_buf_hash_init(), or
radix_tree_preload() failed, the returned value 'error' is not set
accordingly.
Reported-as-fixing: 8b26c5825e ("xfs: handle ENOMEM correctly during initialisation of perag structures")
Fixes: 9b24717979 ("xfs: cache unlinked pointers in an rhashtable")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The aim of the inode btree record iterator function is to call a
callback on every record in the btree. To avoid having to tear down and
recreate the inode btree cursor around every callback, it caches a
certain number of records in a memory buffer. After each batch of
callback invocations, we have to perform a btree lookup to find the
next record after where we left off.
However, if the keys of the inode btree are corrupt, the lookup might
put us in the wrong part of the inode btree, causing the walk function
to loop forever. Therefore, we add extra cursor tracking to make sure
that we never go backwards neither when performing the lookup nor when
jumping to the next inobt record. This also fixes an off by one error
where upon resume the lookup should have been for the inode /after/ the
point at which we stopped.
Found by fuzzing xfs/460 with keys[2].startino = ones causing bulkstat
and quotacheck to hang.
Fixes: a211432c27 ("xfs: create simplified inode walk function")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Currently, commit e9e2eae89d dropped a (int) decoration from
XFS_LITINO(mp), and since sizeof() expression is also involved,
the result of XFS_LITINO(mp) is simply as the size_t type
(commonly unsigned long).
Considering the expression in xfs_attr_shortform_bytesfit():
offset = (XFS_LITINO(mp) - bytes) >> 3;
let "bytes" be (int)340, and
"XFS_LITINO(mp)" be (unsigned long)336.
on 64-bit platform, the expression is
offset = ((unsigned long)336 - (int)340) >> 3 =
(int)(0xfffffffffffffffcUL >> 3) = -1
but on 32-bit platform, the expression is
offset = ((unsigned long)336 - (int)340) >> 3 =
(int)(0xfffffffcUL >> 3) = 0x1fffffff
instead.
so offset becomes a large positive number on 32-bit platform, and
cause xfs_attr_shortform_bytesfit() returns maxforkoff rather than 0.
Therefore, one result is
"ASSERT(new_size <= XFS_IFORK_SIZE(ip, whichfork));"
assertion failure in xfs_idata_realloc(), which was also the root
cause of the original bugreport from Dennis, see:
https://bugzilla.redhat.com/show_bug.cgi?id=1894177
And it can also be manually triggered with the following commands:
$ touch a;
$ setfattr -n user.0 -v "`seq 0 80`" a;
$ setfattr -n user.1 -v "`seq 0 80`" a
on 32-bit platform.
Fix the case in xfs_attr_shortform_bytesfit() by bailing out
"XFS_LITINO(mp) < bytes" in advance suggested by Eric and a misleading
comment together with this bugfix suggested by Darrick. It seems the
other users of XFS_LITINO(mp) are not impacted.
Fixes: e9e2eae89d ("xfs: only check the superblock version for dinode size calculation")
Cc: <stable@vger.kernel.org> # 5.7+
Reported-and-tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Gao Xiang <hsiangkao@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Teach the directory scrubber to check all the bestfree entries,
including the null ones. We want to be able to detect the case where
the entry is null but there actually /is/ a directory data block.
Found by fuzzing lbests[0] = ones in xfs/391.
Fixes: df481968f3 ("xfs: scrub directory freespace")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
We always know the correct state of the rmap record flags (attr, bmbt,
unwritten) so check them by direct comparison.
Fixes: d852657ccf ("xfs: cross-reference reverse-mapping btree")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The comment and logic in xchk_btree_check_minrecs for dealing with
inode-rooted btrees isn't quite correct. While the direct children of
the inode root are allowed to have fewer records than what would
normally be allowed for a regular ondisk btree block, this is only true
if there is only one child block and the number of records don't fit in
the inode root.
Fixes: 08a3a692ef ("xfs: btree scrub should check minrecs")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Patch 541656d3a5 ("gfs2: freeze should work on read-only mounts") changed
the check for glock state in function freeze_go_sync() from "gl->gl_state
== LM_ST_SHARED" to "gl->gl_req == LM_ST_EXCLUSIVE". That's wrong and it
regressed gfs2's freeze/thaw mechanism because it caused only the freezing
node (which requests the glock in EX) to queue freeze work.
All nodes go through this go_sync code path during the freeze to drop their
SHared hold on the freeze glock, allowing the freezing node to acquire it
in EXclusive mode. But all the nodes must freeze access to the file system
locally, so they ALL must queue freeze work. The freeze_work calls
freeze_func, which makes a request to reacquire the freeze glock in SH,
effectively blocking until the thaw from the EX holder. Once thawed, the
freezing node drops its EX hold on the freeze glock, then the (blocked)
freeze_func reacquires the freeze glock in SH again (on all nodes, including
the freezer) so all nodes go back to a thawed state.
This patch changes the check back to gl_state == LM_ST_SHARED like it was
prior to 541656d3a5.
Fixes: 541656d3a5 ("gfs2: freeze should work on read-only mounts")
Cc: stable@vger.kernel.org # v5.8+
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead03 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Don't recycle a refnode until we're done with all requests of nodes
ejected before.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
An active ref_node always can be found in ctx->files_data, it's much
safer to get it this way instead of poking into files_data->ref_list.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
"intel_iommu=off" command line is used to disable iommu but iommu is force
enabled in a tboot system for security reason.
However for better performance on high speed network device, a new option
"intel_iommu=tboot_noforce" is introduced to disable the force on.
By default kernel should panic if iommu init fail in tboot for security
reason, but it's unnecessory if we use "intel_iommu=tboot_noforce,off".
Fix the code setting force_on and move intel_iommu_tboot_noforce
from tboot code to intel iommu code.
Fixes: 7304e8f28b ("iommu/vt-d: Correctly disable Intel IOMMU force on")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Tested-by: Lukasz Hawrylko <lukasz.hawrylko@linux.intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201110071908.3133-1-zhenzhong.duan@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
The error codes were not set on some of these error paths.
Also the error handling was more confusing than it needed to be so I
cleaned it up and shuffled it around a bit.
Fixes: d2fb0a0438 ("dmaengine: break out channel registration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201113101631.GE168908@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sysrq-t ends up invoking show_opcodes() for each task which tries to access
the user space code of other processes, which is obviously bogus.
It either manages to dump where the foreign task's regs->ip points to in a
valid mapping of the current task or triggers a pagefault and prints "Code:
Bad RIP value.". Both is just wrong.
Add a safeguard in copy_code() and check whether the @regs pointer matches
currents pt_regs. If not, do not even try to access it.
While at it, add commentary why using copy_from_user_nmi() is safe in
copy_code() even if the function name suggests otherwise.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Tested-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20201117202753.667274723@linutronix.de
Commit e0d072782c ("dma-mapping: introduce DMA range map, supplanting
dma_pfn_offset") introduced a regression in our code since the second
backed to probe will now get -EINVAL back from dma_direct_set_offset and
will prevent the entire DRM device from probing.
Ignore -EINVAL as a temporary measure to get it back working, before
removing that call entirely.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Checking for ifdef CONFIG_x fails if CONFIG_x=m.
Use IS_ENABLED instead, which is true for both built-ins and modules.
Otherwise, a
> ip -4 route add 1.2.3.4/32 via inet6 fe80::2 dev eth1
fails with the message "Error: IPv6 support not enabled in kernel." if
CONFIG_IPV6 is `m`.
In the spirit of b8127113d0.
Fixes: d15662682d ("ipv4: Allow ipv6 gateway with ipv4 routes")
Cc: Kim Phillips <kim.phillips@arm.com>
Signed-off-by: Florian Klink <flokli@flokli.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201115224509.2020651-1-flokli@flokli.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code refactoring of ILT configuration was not complete, the old
unused variables were used for the SRC block. That could lead to the memory
corruption by HW when rx filters are configured.
This patch completes that refactoring.
Fixes: 8a52bbab39 (qed: Debug feature: ilt and mdump)
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Link: https://lore.kernel.org/r/20201116132944.2055-1-dbogdanov@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
nlmsg_cancel() needs to be called in the error path of
inet_req_diag_fill to cancel the message.
Fixes: d545caca82 ("net: inet: diag: expose the socket mark to privileged processes.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Link: https://lore.kernel.org/r/20201116082018.16496-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add missing define of ALIGN_DOWN to make the test build and run. In
addition, __sg_alloc_table_from_pages now support unaligned maximum
segment, so adapt the test result accordingly.
Fixes: 07da1223ec ("lib/scatterlist: Add support in dynamic allocation of SG table from pages")
Link: https://lore.kernel.org/r/20201115120623.139113-1-leon@kernel.org
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Russell Currey