BugLink: https://bugs.launchpad.net/bugs/826081
The original reporter needs 'Headphone Jack Sense' enabled to have
audible audio, so add his PCI SSID to the whitelist.
Reported-and-tested-by: Muhammad Khurram Khan
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CONFIG_RELOCATABLE code tries to align the unpack destination to
the value of 'kernel_alignment' in the setup_hdr. If that's 0, it
tries to unpack to address 0, which in fact causes the gunzip code
to call 'error("Out of memory while allocating output buffer")'.
The bootloader (ie. the lguest Launcher in this case) should be doing
setting this field; the normal bzImage is 16M, we can use the same.
Reported-by: Stefanos Geraggelos <sgerag@cslab.ece.ntua.gr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Commit db64fe0225 ("mm: rewrite vmap layer") introduced code that does
address calculations under the assumption that VMAP_BLOCK_SIZE is a
power of two. However, this might not be true if CONFIG_NR_CPUS is not
set to a power of two.
Wrong vmap_block index/offset values could lead to memory corruption.
However, this has never been observed in practice (or never been
diagnosed correctly); what caught this was the BUG_ON in vb_alloc() that
checks for inconsistent vmap_block indices.
To fix this, ensure that VMAP_BLOCK_SIZE always is a power of two.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=31572
Reported-by: Pavel Kysilka <goldenfish@linuxsoft.cz>
Reported-by: Matias A. Fonzo <selk@dragora.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: 2.6.28+ <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The snd_usb_caiaq driver currently assumes that output urbs are serviced
in time and doesn't track when and whether they are given back by the
USB core. That usually works fine, but due to temporary limitations of
the XHCI stack, we faced that urbs were submitted more than once with
this approach.
As it's no good practice to fire and forget urbs anyway, this patch
introduces a proper bit mask to track which requests have been submitted
and given back.
That alone however doesn't make the driver work in case the host
controller is broken and doesn't give back urbs at all, and the output
stream will stop once all pre-allocated output urbs are consumed. But
it does prevent crashes of the controller stack in such cases.
See http://bugzilla.kernel.org/show_bug.cgi?id=40702 for more details.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Matej Laitl <matej@laitl.cz>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Function genpd_queue_power_off_work() is not defined for
CONFIG_PM_RUNTIME, so pm_genpd_poweroff_unused() causes a build
error to happen in that case. Fix the problem by making
pm_genpd_poweroff_unused() depend on CONFIG_PM_RUNTIME too.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove the name of Sergey Kostyliov as maintainer of befs.
In the MAINTAINERS file, befs is orphaned.
Signed-off-by: Marcos Souza <marcos.mage@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
General cleanups to kernel-parameters.txt:
- add missing $ARCH that are being used/referenced
- alphabetize the parameter restrictions list
- spell "IA-64" as listed in arch/ia64/Kconfig instead of "IA64"
- remove trailing whitespace
- use hyphen in 32-bit etc.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Usually kernel parameters are documented in kernel-parameters.txt
but user_debug is only documented in the Kconfig. Document the
option and point to the Kconfig help text for more info.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dropping LSD (Linux Source Driver) since it hasn't been available
for a long time.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts. This makes SDIO work.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk.
(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Bug discovered by Jan Kara:
Finally, commit 1449032be1 returned back
the old IO submission code but apparently it forgot to return the old
handling of uninitialized buffers so we unconditionnaly call
block_write_full_page() without specifying end_io function. So AFAICS
we never convert unwritten extents to written in some cases. For
example when I mount the fs as: mount -t ext4 -o
nomblk_io_submit,dioread_nolock /dev/ubdb /mnt and do
int fd = open(argv[1], O_RDWR | O_CREAT | O_TRUNC, 0600);
char buf[1024];
memset(buf, 'a', sizeof(buf));
fallocate(fd, 0, 0, 16384);
write(fd, buf, sizeof(buf));
I get a file full of zeros (after remounting the filesystem so that
pagecache is dropped) instead of seeing the first KB contain 'a's.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
EXT4_IO_END_UNWRITTEN flag set and the increase of i_aiodio_unwritten
should be done simultaneously since ext4_end_io_nolock always clear
the flag and decrease the counter in the same time.
We don't increase i_aiodio_unwritten when setting
EXT4_IO_END_UNWRITTEN so it will go nagative and causes some process
to wait forever.
Part of the patch came from Eric in his e-mail, but it doesn't fix the
problem met by Michael actually.
http://marc.info/?l=linux-ext4&m=131316851417460&w=2
Reported-and-Tested-by: Michael Tokarev<mjt@tls.msk.ru>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Flush inode's i_completed_io_list before calling ext4_io_wait to
prevent the following deadlock scenario: A page fault happens while
some process is writing inode A. During page fault,
shrink_icache_memory is called that in turn evicts another inode
B. Inode B has some pending io_end work so it calls ext4_ioend_wait()
that waits for inode B's i_ioend_count to become zero. However, inode
B's ioend work was queued behind some of inode A's ioend work on the
same cpu's ext4-dio-unwritten workqueue. As the ext4-dio-unwritten
thread on that cpu is processing inode A's ioend work, it tries to
grab inode A's i_mutex lock. Since the i_mutex lock of inode A is
still hold before the page fault happened, we enter a deadlock.
Also moves ext4_flush_completed_IO and ext4_ioend_wait from
ext4_destroy_inode() to ext4_evict_inode(). During inode deleteion,
ext4_evict_inode() is called before ext4_destroy_inode() and in
ext4_evict_inode(), we may call ext4_truncate() without holding
i_mutex lock. As a result, there is a race between flush_completed_IO
that is called from ext4_ext_truncate() and ext4_end_io_work, which
may cause corruption on an io_end structure. This change moves
ext4_flush_completed_IO and ext4_ioend_wait from ext4_destroy_inode()
to ext4_evict_inode() to resolve the race between ext4_truncate() and
ext4_end_io_work during inode deletion.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
ext4_should_writeback_data() had an incorrect sequence of
tests to determine if it should return 0 or 1: in
particular, even in no-journal mode, 0 was being returned
for a non-regular-file inode.
This meant that, in non-journal mode, we would use
ext4_journalled_aops for directories, symlinks, and other
non-regular files. However, calling journalled aop
callbacks when there is no valid handle, can cause problems.
This would cause a kernel crash with Jan Kara's commit
2d859db3e4 ("ext4: fix data corruption in inodes with
journalled data"), because we now dereference 'handle' in
ext4_journalled_write_end().
I also added BUG_ONs to check for a valid handle in the
obviously journal-only aops callbacks.
I tested this running xfstests with a scratch device in
these modes:
- no-journal
- data=ordered
- data=writeback
- data=journal
All work fine; the data=journal run has many failures and a
crash in xfstests 074, but this is no different from a
vanilla kernel.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Some older Panasonic made camcorders (Panasonic AG-EZ30 and NV-DX110,
Grundig Scenos DLC 2000) reject requests with ack_busy_X if a request is
sent immediately after they sent a response to a prior transaction.
This causes firewire-core to fail probing of the camcorder with "giving
up on config rom for node id ...". Consequently, programs like kino or
dvgrab are unaware of the presence of a camcorder.
Such transaction failures happen also with the ieee1394 driver stack
(of the 2.4...2.6 kernel series until 2.6.36 inclusive) but with a lower
likelihood, such that kino or dvgrab are generally able to use these
camcorders via the older driver stack. The cause for firewire-ohci's or
firewire-core's worse behavior is not yet known. Gap count optimization
in firewire-core is not the cause. Perhaps the slightly higher latency
of transaction completion in the older stack plays a role. (ieee1394:
AR-resp DMA context tasklet -> packet completion ktread -> user process;
firewire-core: tasklet -> user process.)
This change introduces retries and delays after ack_busy_X into
firewire-core's Config ROM reader, such that at least firewire-core's
probing and /dev/fw* creation are successful. This still leaves the
problem that userland processes are facing transaction failures.
gscanbus's built-in retry routines deal with them successfully, but
neither kino's nor dvgrab's do ever succeed.
But at least DV capture with "dvgrab -noavc -card 0" works now. Live
video preview in kino works too, but not actual capture.
One way to prevent Configuration ROM reading failures in application
programs is to modify libraw1394 to synthesize read responses by means
of firewire-core's Configuration ROM cache. This would only leave
CMP and FCP transaction failures as a potential problem source for
applications.
Reported-and-tested-by: Thomas Seilund <tps@netmaster.dk>
Reported-and-tested-by: René Fritz <rene@colorcube.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device
USB: Serial: Add device ID for Sierra Wireless MC8305
USB: Serial: Added device ID for Qualcomm Modem in Sagemcom's HiLo3G
usb/host/pci-quirks.c: correct annotation of `ehci_dmi_nohandoff_table'
USB: option driver: add PID for Vodafone-Huawei K4511
USB: option driver: add PID for Vodafone-Huawei K4510
USB: option driver: add PID for Vodafone-Huawei K3771
USB: option driver: add PID for Vodafone-Huawei K3770
usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too
usb/isp1760: Added missing call to usb_hcd_check_unlink_urb() during unlink
USB: EHCI: Fix test mode sequence
USB: ftdi_sio: fix minor typo in get_ftdi_divisor
USB: at91_udc: include linux/prefetch.h explicitly
USB: usb-storage: unusual_devs entry for ARM V2M motherboard.
usb/ehci-mxc: add missing inclusion of mach/hardware.h
USB: assign instead of equal in usbtmc.c
usb: renesas_usbhs: fixup usbhsg_for_each_uep 1st pos
usb: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: gadget: net2272 - Correct includes
usb: musb: fix oops on musb_gadget_pullup
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
zcache: Fix build error when sysfs is not defined
zcache: Use div_u64 for 64-bit division
staging:rts_pstor: fix thread synchronization flow
drivers:staging:solo6x10:add the missed slab.h
staging: zcache: include module.h for MODULE_LICENSE
drivers/staging/hv/blkvsc_drv.c: eliminate NULL pointer dereference
Staging: Add clk API note to nvec/TODO
drivers/staging/ath6kl/miscdrv/ar3kps/ar3kpsparser.c: adjust array index
staging: more missing slab.h inclusions
drivers/staging/solo6x10/p2m.c needs slab.h
drivers/staging/solo6x10/core.c needs slab.h
drivers/staging/dt3155v4l/dt3155v4l.c needs slab.h
drivers/staging/speakup/devsynth.c: fix "buffer size is not provably correct" error
Staging: iio: add some unlocks to raw_read() functions
staging: ft1000_proc needs asm/io.h for inw/outw on sparc
staging: rtl8192u: declare MODULE_FIRMWARE
gma500: Fix clashes with DRM updates
staging: zcache: module is GPL
staging: fix zcache building
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-tip:
x86-64: Rework vsyscall emulation and add vsyscall= parameter
x86-64: Wire up getcpu syscall
x86: Remove unnecessary compile flag tweaks for vsyscall code
x86-64: Add vsyscall:emulate_vsyscall trace event
x86-64: Add user_64bit_mode paravirt op
x86-64, xen: Enable the vvar mapping
x86-64: Work around gold bug 13023
x86-64: Move the "user" vsyscall segment out of the data segment.
x86-64: Pad vDSO to a page boundary
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: replace xfs_buf_geterror() with bp->b_error
xfs: Check the return value of xfs_buf_read() for NULL
"xfs: fix error handling for synchronous writes" revisited
xfs: set cursor in xfs_ail_splice() even when AIL was empty
xfs: Remove the macro XFS_BUFTARG_NAME
xfs: Remove the macro XFS_BUF_TARGET
xfs: Remove the macro XFS_BUF_SET_TARGET
Replace the macro XFS_BUF_ISPINNED with helper xfs_buf_ispinned
xfs: Remove the macro XFS_BUF_SET_PTR
xfs: Remove the macro XFS_BUF_PTR
xfs: Remove macro XFS_BUF_SET_START
xfs: Remove macro XFS_BUF_HOLD
xfs: Remove macro XFS_BUF_BUSY and family
xfs: Remove the macro XFS_BUF_ERROR and family
xfs: Remove the macro XFS_BUF_BFLAGS
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
Since we just checked bp for NULL, it is ok to replace
xfs_buf_geterror() with bp->b_error in these places.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Check the return value of xfs_buf_read() for NULL and return ENOMEM
if it is NULL. This is necessary in a few spots to avoid subsequent
code blindly dereferencing the null buffer pointer.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>