This prevents efx->link_advertising from being blatted during
a reset.
The phy_short_reach sysfs node is now destroyed later in the
port shutdown process, so check for STATE_RUNNING after
acquiring the rtnl_lock (just like in set_phy_flash_cfg).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function efx_iterate_state contains the code
memcpy(&payload->msg, payload_msg, sizeof(payload_msg));
This is the only use of payload_msg. The type of payload_msg is
changed from a pointer to an array, so that the result of sizeof really is
the length of the string.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been mostly rewritten since Michael Brown's initial
work, so swap the order of the authors.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This integrates support for the SFC9000 family of 10G Ethernet
controllers and LAN-on-motherboard chips, starting with the SFL9021
'Siena' and SFC9020 'Bethpage'.
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the SFC9000 family of 10G Ethernet controllers
and LAN-on-motherboard chips, starting with the SFL9021 'Siena' and
SFC9020 'Bethpage'.
The SFC9000 family is based on the SFC4000 'Falcon' architecture, but
with some significant changes:
- Two ports are associated with two independent PCI functions
(except SFC9010)
- Integrated 10GBASE-T PHY(s) (SFL9021/9022)
- MAC, PHY and board peripherals are managed by firmware
- Driver does not require board-specific code
- Firmware supports wake-on-LAN and lights-out management through NC-SI
- IPv6 checksum offload and RSS
- Filtering by MAC address and VLAN (not included in this code)
- PCI SR-IOV (not included in this code)
Credit for this code is largely due to my colleagues at Solarflare:
Guido Barzini
Steve Hodgson
Kieran Mansley
Matthew Slattery
Neil Turton
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new NICs flash is managed by firmware and we will use high-level
operations on partitions rather than direct SPI commands. Add support
for multiple MTD partitions per flash device and remove the direct
link between MTD and SPI devices. Maintain a list of MTD partitions
in struct efx_nic.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs have firmware managing the PHY, and we will discover the PHY
capabilities at run-time. Replace the static data with probe() and
test_name() operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New NICs and PHYs support a wider variety of loopback modes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_probe_nic_variant() does a lot less than it used to, and a
lot less than it claims to. Fold the remainder into its caller.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor efx_reset_down() and efx_reset_up() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-LAN is a stub for Falcon, but will be implemented fully for
new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the efx_nic_type::monitor operation or event handling as
appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor PHY, MAC and NIC configuration operations so that the
existing link configuration can be re-pushed with:
efx->phy_op->reconfigure(efx);
efx->mac_op->reconfigure(efx);
and a new configuration with:
efx->nic_op->reconfigure_port(efx);
(plus locking and error-checking).
We have not held the link settings in software (aside from flow
control), and have relied on asking the hardware what they are. This
is a problem because in some cases the hardware may no longer be in a
state to tell us. In particular, if an entire multi-port board is
reset through one port, the driver bindings to other ports have no
chance to save settings before recovering.
We only actually need to keep track of the autonegotiation settings,
so add an ethtool advertising mask to struct efx_nic, initialise it
in PHY init and update it as necessary.
Remove now-unneeded uses of efx_phy_op::{get,set}_settings() and
struct ethtool_cmd.
Much of this was done by Steve Hodgson <shodgson@solarflare.com>.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation for adding differing implementations for new NICs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause frame generation is gated by both RX_XOFF_MAC_EN and an enable
bit in each MAC. RX_XOFF_MAC_EN bit always reads back as 0 so we need
to set it correctly every time we modify RX_CFG_REG. Simplify this by
always setting it to 1 and only changing the enable bits in the MACs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register only needs to be written after reset, not each time we
enable interrupts.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'likely' hint to test of rx_checksum_enabled.
Don't count IP fragments; the IP stack can do that.
Do count non-matching multicast packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "bug9141 workaround" of setting TX_FLUSH_MIN_LEN_EN should really
be considered as a normal bit of configuration rather than a
workaround.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strap bits are only important on Falcon A and all production
boards using it have fixed-speed 10G PHYs.
Replace dummy MAC operations with default MAC operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We never use MDIO in atomic context, so we don't need to spin.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading standard registers on the QT2025C before its firmware has
booted may cause the boot process to fail. Therefore, follow the
recommended reset sequence before reading its id registers. Either
order works for the QT2022C2, so don't differentiate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Falcon can generate events for LASI interrupts from the PHY, but in
practice we have never implemented this in reference designs. Instead
we have polled, inserted the appropriate events, and then handled the
events later. This is a waste of time and code.
Instead, make PHY poll functions update the link state synchronously
and report whether it changed. We can still make use of the LASI
registers as a shortcut on the SFT9001.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Currently we can set multicast hash immediately (in atomic context)
but must delay setting MAC promiscuity. There is not that much
point in deferring one but not the other, and setting the multicast
hash on Siena will involve a firmware request. So process them
both in efx_mac_work().
Also, set the broadcast bit in the multicast hash in
efx_set_multicast_list(), since this is required for both Falcon and
Siena.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Only the XMAC on Falcon needs help from the driver to poll and reset
the MAC-PHY link (XAUI); GMII is a simple parallel bus and on later
NICs firmware takes care of the XAUI link. Also, an XMAC interrupt
currently schedules a work item which simply clears a flag
(efx_nic::mac_up) to be checked by the regular monitor (or the next
link reconfiguration, if that is sooner).
Rename the flag to xmac_poll_required, changing its sense. Remove the
needless indirection and just set the flag immediately. Call
falcon_xmac_poll() directly where required.
Add a new generic operation mac_op::check_fault to check the link
outside of regular monitoring, as required during self-tests.
(Note that this leaves us with an unused work item, but we will
immediately have another use for it.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
Currently we initiate MAC stats DMA and busy-wait for completion when
stats are requested. We can improve on this with a periodic timer to
initiate and poll for stats, and opportunistically poll when stats are
requested.
Since efx_nic::stats_disable_count and efx_stats_{disable,enable}()
are Falcon-specific, rename them and move them accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although efx_init_port() is only called at probe time and so cannot
race with port reconfiguration, most of the functions it calls can
expect to be called with the MAC lock held.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid overrunning the hardware limit of 4 concurrent RX queue flushes.
Expand the queue flush state to support this. Make similar changes to
TX flushing to keep the code symmetric.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put all static information in struct falcon_board_type and replace it
with a pointer in struct falcon_board. Simplify probing aocordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although all the defined fields in these registers are within 32 bits,
they are architecturally defined as 128-bit like most other Falcon
registers. In particular, we must use efx_reado() to ensure proper
locking when reading MD_STAT_REG.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These were accidentally undersized by a factor of 2, which limited
performance.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define name tables for these enumerations in a similar way as for
loopback. Move the loopback name table together with them.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All files that include ethtool.h, rx.h or tx.h are also including
efx.h, and there is no good reason to separate out the few
declarations they contain. Therefore fold them into efx.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At some point these casts were used to remove const qualification, but
they are now unneeded.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation for moving Falcon-specific state required by other
Falcon-specific code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename struct efx_board to struct falcon_board.
Introduce and use inline function to look up board info from struct
efx_nic, in preparation for moving it.
Move board init and fini calls into NIC probe and remove functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_board::init_leds was introduced as a second stage of
initialisation because of the inter-dependency between the board and
PHY. We want to move board initialisation into NIC probing, which is
too early to use MDIO, so SFN4111T initialisation also needs to be
split.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only some PHYs have firmware support for a LED blink mode, so we
currently blink the others in a timer function. Since all PHYs have
simple on and off modes, we don't gain anything by using multiple
blink implementations. Also, since we have a process context there
is no need to use a timer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the need to use a label and goto, and makes the two
branches mirror each other more closely.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function no longer has any common cleanup code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish the job by removing the structure member.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers need to be able to prevent access to an I2C bus segment
for a specific period of time. Add an interface for them to do so
without twiddling with i2c-core internals.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Now that we can tell whether GRO is being applied, this heuristic is
effective once more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When GRO is successfully merging received packets, we should allocate
raw page buffers rather than skbs that will be discarded by GRO.
Otherwise, we should allocate skbs.
GRO also benefits from higher interrupt moderation, so increase the
score for mergeable RX packets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO. The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have never checked the efx_nic::rx_checksum_enabled flag everywhere
we should, and since the switch to GRO we don't check it anywhere.
It's simplest to check it in the one place where we initialise the
per-packet checksummed flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs,
covering both more and less than XFP. Rename its functions and
constants to reflect reality and to reduce namespace pollution when
sfc is a built-in driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only multi-speed PHY driver using this is 10Xpress, and it does
not support non-autoneg operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_fc_resolve() is specific to MDIO and is not used by any other
function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTD partition is named based on the netdev name, which is set to
'eth%d' before registration. Also, the MTD partition will currently
be left registered if netdev registration fails.
Fix both these problems by moving the MTD probe after netdev
registration. Hold the RTNL to serialise this with the netdev
notifier that calls efx_mtd_rename().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cleanup functions will never be called if the MMIO region could
not be mapped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC and PHY probing are bound up together, as evidenced by the
initialisation of efx_nic::loopback_modes. Remove the current
arbitrary separation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the implementation a lot.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes efx_pci_remove_main() more obviously the inverse of
efx_pci_probe_main(), and matches our out-of-tree driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the duplicated logic in efx_enqueue_skb() and
efx_tx_queue_insert() with an inline function, efx_max_tx_len().
Remove the failed attempt at abstracting hardware-specifics and put
all the magic numbers in efx_max_tx_len().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move size and mask definitions into efx.h; calculate page orders in falcon.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While we're at it, use type suffixes of 'd', 'q' and 'o', consistent
with register type names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena is still based on the Falcon hardware architecture and will
share many of these definitions, so replace falcon_hwdefs.h with
regs.h.
The new definitions have been generated according to a naming
convention which incorporates the type and revision information.
Update the code accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since there are now separate blocks of code to set the thresholds for
each NIC type, it is no longer useful to include them in the NIC type
description.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros are not extensible to more than two NIC types without
repetition of register definitions, and they are only used to deal
with a few fields in RX_CFG_REG and global events which moved between
Falcon rev A1 and B0.
Therefore:
- Move RX_CFG_REG initialisation into its own function which tests the
NIC revision just once
- Explicitly test the NIC revision when checking the RX_RECOVERY flag in
global events
- Merge definitions of RX_XOFF_MAC_EN flag, which did not move
- Remove the macro definitions
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Siena will require entirely different board code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 27fbc7d 'mdio: Expose pause frame advertising flags to ethtool'
and c634263 'sfc: 10Xpress: Initialise pause advertising flags'
added to our reported advertising flags.
efx_mdio_set_settings() requires that all advertising flags are
also present in the supported flags, so make sure that is true.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio module now handles reconfiguration of pause advertising
through ethtool, but not initialisation. Add the necessary
initialisation to tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove open-coded zalloc_cpumask_var() and zalloc_cpumask_var_node().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a couple of cases collapse some extra code like:
int retval = NETDEV_TX_OK;
...
return retval;
into
return NETDEV_TX_OK;
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reconfiguring the port requires us to flush all DMA queues. In
repeated testing we have found that RX flushes would sometimes fail
because the RX DMA engine was not properly isolated from the MACs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received frames must be re-clocked by the local XGXS to the 156.25 MHz
(DDR) clock of the XGMII. If the remote clock is slightly faster this
can reduce a minimum IPG of 64 bit-times (1 cycle) to 32 bit-times
(half a cycle). If the XMAC detects that a frame has reached the
maximum RX frame length in the same cycle that it receives one of
these reduced IPGs, it may miss the IPG, causing two valid frames to
be treated as a single invalid frame (over-length with bad CRC).
We work around this by increasing the maximum RX frame length so that
peers with matched MTU will not provoke this bug.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At probe time, falcon_reset_hw() performs a hard reset of the PHY
along with Falcon. There is no need to perform a soft reset later,
and any access to standard MDIO registers before the PHY firmware has
booted can interrupt the boot process, making the port unusable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_reset_xaui() waits for XGXS reset to complete, but the XAUI
serdes reset may take longer. It needs to check both reset active
bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must call netif_carrier_off() after the device is registered, not
before, to set the operational state and user-space IFF_RUNNING flag
correctly.
Since we don't want observers to see an intermediate state, open-code
register_netdev() and add efx_update_name() and netif_carrier_off()
into the locked region.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commits 9d21493b4b
and 08baf56108
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.
Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO/LRO can be controlled through ethtool so this is unnecessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change error message when alloc_cpumask_var fails.
Repairs "cpumask: convert drivers/net/sfc".
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the newly-added generic MDIO clause 45 support and remove
redundant definitions.
Add an 'efx_' prefix to the remaining driver-specific MDIO functions
and remove arguments which are redundant with efx->mdio.prtad.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that copying a 16-byte area at ~800k times a second
can be really expensive :) This patch redesigns the frags GRO
interface to avoid copying that area twice.
The two disciples of the frags interface have been converted.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
falcon_sim_phy_event() used EFX_OWORD_FIELD, which operates on
bitfields in 128-bit values, on an event, which is a 64-bit value.
This should be harmless - these macros always use little-endian
ordering, so it would read and write back the following 8 bytes
unchanged - but it is obviously wrong.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfc could call netif_napi_add() multiple times for the same
napi_struct, corrupting the list of napi_structs for the associated
device and leading to a busy-loop on device removal. Move the call to
netif_napi_add() and add a call to netif_napi_del() in the obvious
places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither the lm90 driver nor the lm87 driver do support interrupts, so
there is no point in specifying one when declaring the devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we use a shared legacy IRQ then our interrupt handler may be called
as soon as it is registered even though IRQs are disabled on the NIC.
Now that the legacy interrupt handler also checks for event delivery,
it may decide to schedule polling in this case. Ensure that the NAPI
context is valid but disabled at this point.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculate a score for each 1000 IRQs:
- TX completions are worth 1 point
- RX completions are worth 4 if merged using LRO or 2 otherwise
Reduce moderation if the score is less than 10000, down to a minimum
of 5 us. Increase moderation if the score is more than 20000, up to
the specified maximum.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug this function works around only applies to the first set of
page-mapped registers; other pages can be written without locking.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases, reading the legacy interrupt status register can
acknowledge an event queue whose attention flag has not yet been set
in the register. Until we service this event queue it will not
generate any more interrupts. Therefore, as a secondary check, poll
the next slot in each active event queue whose flag is not set.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet parser used in the TX data path for locating checksum
fields can lose synchronisation with the TX queue manager when
handling packets that look like IPv4 but are too short (17-32 bytes).
Work around this by padding to 33 bytes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the error count a per-NIC variable.
Reset this the count after an hour if it has not reached the critical value.
Set the critical value back to 5.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flushing queues we disable normal interrupt and event handling and
poll event queue 0 looking for flush completions. Unfortunately the
flush event polling loop fails to move past any other type of event.
This problem has not been observed in production hardware but appears to
be a possibility.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_del_adapter() leaves dangling pointers in the structure. If we
retry the NIC probe and pass the structure to i2c_add_adapter() again
it will lead to an oops unless we clear it first.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If MAC switching fails, stop the port properly.
If PHY reinitialisation fails, clear the port_initialized flag.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinitialise LEDs after overriding them for identification.
Rename set_fault_led method to set_id_led since we always use it for
NIC identification and not faults.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new PHY supporting SFP+ modules, used in the SFN4112F
reference design. It is similar to the QT2022C2 and shares much of
its support code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuffle bits of the OUI into the conventional written order.
Replace PHY id component macros with functions.
Zero-pad PHY id components in log messages.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SFN4111T initialisation, check whether the PHY boot status
indicates a bad firmware checksum. If so, prepare to reflash rather
than continuing with normal initialisation.
Remove redundant PHY boot status check from tenxpress_phy_init().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 27dd2caca4 changed
mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and
to combine their values into an unsigned 32-bit mask. This made the
following test for a negative (failure) value useless. Fix it to
check whether either read failed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Include the header file. If CONFIG_SFC_MTD is not defined
then the functions 'efx_mtd_remove' and 'efx_mtd_rename' are defined
'static inline' with an empty function body in the header file, but
the the whole file mtd.c is not built in this case.
Fix this sparse warnings:
drivers/net/sfc/mtd.c:204:6: warning: symbol 'efx_mtd_remove' was not declared. Should it be static?
drivers/net/sfc/mtd.c:221:6: warning: symbol 'efx_mtd_rename' was not declared. Should it be static?
drivers/net/sfc/mtd.c:230:5: warning: symbol 'efx_mtd_probe' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: Move variable declaration as close to their usage as possible.
Fix this sparse warning:
drivers/net/sfc/tenxpress.c:589:22: warning: symbol 'link_ok' shadows an earlier one
drivers/net/sfc/tenxpress.c:575:30: originally declared here
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/sfc/falcon.c: In function ‘falcon_alloc_special_buffer’:
drivers/net/sfc/falcon.c:340: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 10 has type ‘phys_addr_t’
drivers/net/sfc/falcon.c: In function ‘falcon_free_special_buffer’:
drivers/net/sfc/falcon.c:355: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 10 has type ‘phys_addr_t’
drivers/net/sfc/falcon.c: In function ‘falcon_probe_port’:
drivers/net/sfc/falcon.c:2346: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 7 has type ‘phys_addr_t’
drivers/net/sfc/falcon.c: In function ‘falcon_probe_nic’:
drivers/net/sfc/falcon.c:2924: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 7 has type ‘phys_addr_t’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset. This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is not specific to rev A.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the loopback mode, there may be no pertinent link state
bits. In this case we test the PHYXS RX fault bit instead. Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, set pause advertising bits properly.
A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before. This ensures that the value is
correct after an online reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.
Update comments to explain exactly what we're doing.
Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750). We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors. This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware. Therefore remove it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes sfc invoke the GRO hooks instead of LRO. As
GRO has a compatible external interface to LRO this is a very
straightforward replacement.
Everything should appear identical to the user except that the
offload is now controlled by the GRO ethtool option instead of
LRO. I've kept the lro module parameter as is since that's for
compatibility only.
I have eliminated efx_rx_mk_skb as the GRO layer can take care
of all packets regardless of whether GRO is enabled or not.
So the only case where we don't call GRO is if the packet checksum
is absent. This is to keep the behaviour changes of the patch to
a minimum.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: reduce stack usage, use new cpumask API.
Remove a cpumask from the stack. Ben Hutchings indicated that printing
a warning and returning 1 was acceptable for the corner case where allocation
fails.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: linux-net-drivers@solarflare.com
Impact: reduce stack usage, use new cpumask API.
This actually uses topology_core_cpumask() and
topology_thread_cpumask(), removing the only users of
topology_core_siblings() and topology_thread_siblings()
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: linux-net-drivers@solarflare.com
Only the SFX7101 requires software power control. This was
incorrectly being applied to the SFT9001 rev A as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_disable_device() disables many features, like MSI-X, which we
never reenable in efx_reset(). Further, calls to pci_enable_device()
and pci_disable_device() must be matched since the nesting count was
introduced, so switch to using pci_clear_master() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we removed the network device argument from several
NAPI interfaces in 908a7a16b8
("net: Remove unused netdev arg from some NAPI interfaces.")
several drivers now started getting unused variable warnings.
This fixes those up.
Signed-off-by: David S. Miller <davem@davemloft.net>
When AN is enabled and the link is down the speed/duplex control bits
will not be meaningful. Use the advertising bits instead, and mask
them with the LPA bits if and only if AN is complete (as before).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should reduce user confusion and may also aid recovery (ioctls
will still be available).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFT9001 firmware implements cable diagnostics; run those and
include their results in a self-test. In case of a cable fault, do
not fail the self-test as a whole; only faults in the NIC should cause
that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in ethtool test flags to determine which tests to run.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently efx_mtd_rename() can race with the probe() and remove()
functions.
Move probe() before device registration and remove() after
unregistration. Move initialisation/update of all names based on the
netdev name into a new function and call it under the RTNL immediately
after registration.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the mtd field is not initialised early enough.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
efx_pci_probe_main() can return success despite a reset being scheduled.
Catch this and retry or abort probe depending on the reset type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the PHY type names are overly generic. Change them to include
the model numbers of the PHYs they represent.
Correct the model number reference at the top of xfp_phy.c.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool must contend with the MTD driver for the SPI bus lock, which
may carry out long operations such as flash erase. Allow it to be
interrupted while waiting.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our ethtool self-test result names each begin with a component name. For
some results this is "port0", which is not very meaningful. Change that
to "rx" or "phy" as appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support code for the SFN4111T 100/1000/10GBASE-T reference design,
based in part on the existing code for the SFE4001.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add type codes for the new PHY and rename the SFX7101 type code.
Add definition of clause 22 extension MMD.
Adapt the 10Xpress SFX7101 code to support the SFT9001 as well.
Clean up register definitions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Steve Hodgson <shodgson@solarflare.com>
MAC, PHY and board events may be separately enabled and signalled.
Our current arrangement of chaining the polling functions can result
in events being missed. Change them to be more independent.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for auto-negotiation of speed, duplex and flow
control.
When using 10Xpress, auto-negotiate flow control. While we're
at it, clean up the code to warn when partner is not 10GBASE-T
capable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has a separate MAC for use at sub-10G speeds. Introduce
an efx_mac_operations structure with implementations for the two MACs.
Switch between the MACs as necessary.
PHY settings are independent of the MAC, so add get_settings() and
set_settings() to efx_phy_operations. Also add macs field to indicate
which MACs the PHY is connected to.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We often want to set or clear a flag in an MDIO register, but avoid
writing if no change is required since this can have side-effects.
Encapsulate this in a function, mdio_clause45_set_flag().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kluge for development boards with unspecified board type.
Remove assumption of contiguous board type code assignments.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine DEVS0 and DEVS1 registers into a 32-bit mask instead of
reading just DEVS0.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace efx_nic::link_options bitfield with link_speed (speed in
Mbit/s) and link_fd (full duplex flag).
Remove broken auto-negotiation functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loopback self-test checks that IP packets with incorrect checksums
are not altered when sent on a queue with checksum generation off.
These should not contribute to RX error statistics.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "channel" to "chan".
Shorten PHY loopback names.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate IRQs with the name format <device>[-<type>]-<number> so that
future versions of irqbalanced understand what we're doing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a bidirectional forwarding test, we find that the best performance
is achieved by sending the TX completion interrupts from one NIC to a
CPU which shares an L2 cache with RX completion interrupts from the
other NIC. To facilitate this, add an option (through a module
parameter) to create separate channels for RX and TX completion with
separate IRQs when MSI-X is available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed for recovery in case a PHY firmware upgrade is aborted.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFC4000 has strap pins indicating the presence of SPI flash and/or
EEPROM. These pins are also used for GPIO, and in some cases they may
be read wrongly at reset. However, on production boards it must boot
from one or the other device, so we can assume the boot device is
present and read the board config from there.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make falcon_spi_wait() ignore the write timer - it is only relevant to
write commands, it only works for the device that contains VPD, and it
might not be initialised properly at all.
Rename falcon_spi_fast_wait() to falcon_spi_wait_write(), reflecting
its use, and make it wait up to 10 ms (not 1 ms) since buffered writes
to EEPROM may take this long to complete.
Make both wait functions sleep instead of busy-waiting.
Replace wait for command completion at top of falcon_spi_cmd() with a
single poll; no command should be running when the function starts.
Correct some comments.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each reset is serialised by the rtnl_lock anyway, so there's no win
per-NIC.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A value of 0 means indefinite repetition (until interrupted).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was only ever needed for an FPGA version of Falcon.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set dummy monitor method for unrecognised boards.
Clean up board resources if efx_pci_probe_main() fails after board has
been initialised.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert driver to new net_device_ops. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap found that SFC_MTD was selected when sfc was built-in and
the MTD core was a module. Don't allow that combination.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the network device ops get_stats call to be immutable, the handling
of the default internal network device stats block has to be changed. Add a new
helper function which replaces the old use of internal_get_stats.
Note: change return code to make it clear that the caller should not
go changing the returned statistics.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The TX watchdog should trigger a reset, but a temperature/power alarm
should not as this is unlikely to solve the problem.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash. Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.
Add a comment on the partitioning.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
FALCON_SPI_MAX_LEN has type size_t while other SPI lengths have type
unsigned int. This results in warnings from min() on 64-bit
architectures where they are different. Add a cast to make it match.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For some buffers we use a starting offset of either NET_IP_ALIGN or 0
depending on whether we believe the architecture supports efficient
access to unaligned words. There is now a config macro specifying
whether this is the case, so check that rather than checking for
specific architectures.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This should avoid an interrupt storm, which has been observed in the
field with one faulty board.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This prevents speculative reading of the statistics before the
completion flag.
From: Neil Turton <nturton@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
mdio_clause45_links_ok() correctly checks efx_phy_mode_disabled(), so
tenxpress_link_ok() doesn't need to.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Increase the potential retry count for RX flushes from 5 to 100.
Stop polling the RX_DESC_PTR_TBL to infer that a flush might have
happened. Instead absolutely rely on the flush events, unless bug 7803
applies (Falcon rev A only).
To keep things quick, request flushes for every TX and RX queue up
front, and match up the events to requests.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On some boards 10Xpress feeds a 156 MHz clock to the Falcon XMAC. MAC
statistics DMA can fail while this clock is stopped during a PHY reset.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There was a bug in XAUI synchronisation in early 10Xpress firmware
versions. This is fixed in released firmware and we do not need to
work around it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Match pci_request_region() with pci_release_region(), not
release_mem_region().
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When !port_enabled, defer the write to reconfigure_mac_wrapper.
Whilst here, simplify the logic now that efx_start_port() always calls
efx_reconfigure_port().
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally a kludge to fix broken locking, which has since
been fixed properly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Include PMA/PMD in loopback self-tests as intended.
Add NVRAM checksum validation and include it in self-tests.
Add register self-tests.
Run PHY self-tests where available.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This will support register self-tests.
From: Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Move more code from efx_reset() into efx_reset_down() and efx_reset_up().
Stop propagating MAC/PHY setting failures from efx_reset_down() and
efx_reset_up() as these should not be fatal.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some functions return an error code which is always 0. Change their
return types to void and simplify their callers accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Update comment on the dummy operation implementations.
Line up the board operation initialisers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows updating PHY firmware for one interface without removing
all other interfaces handled by the driver.
Replace tx_disabled flags and 10Xpress status enumeration with flags in
enum efx_phy_mode.
Prevent an interface from being brought up while in PHY flash mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>