We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Binding and unbinding the switch driver which creates the DSA slave
network devices for which we set-up inspection would lead to
undesireable effects since we were not clearing the port/queue mapping
to the SYSTEMPORT TX queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a bitmap speeds up the finding of the first available queue
to which we could start establishing the mapping for, but we still have
to loop over all slave network devices to set them up. Simplify the
logic to have a single loop, and use the fact that a correctly
configured ring has inspect set to true. This will make things simpler
to unwind during device unregistration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the system suspend states that we support wipe out entirely the
HW contents. If we had a Wake-on-LAN filter programmed prior to going
into suspend, but we did not actually wake-up from Wake-on-LAN and
instead used a deeper suspend state, make sure we restore the CID number
that we need to match against.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A timing hazard exists when the network interface is stopped that
allows a watchdog timeout to be processed by a separate core in
parallel. This creates the potential for the timeout handler to
wake the queues while the driver is shutting down, or access
registers after their clocks have been removed.
The more common case is that the watchdog timeout will produce a
warning message which doesn't lead to a crash. The chances of this
are greatly increased by the fact that bcm_sysport_netif_stop stops
the transmit queues which can easily precipitate a watchdog time-
out because of stale trans_start data in the queues.
This commit corrects the behavior by ensuring that the watchdog
timeout is disabled before enterring bcm_sysport_netif_stop. There
are currently only two users of the bcm_sysport_netif_stop function:
close and suspend.
The close case already handles the issue by exiting the RUNNING
state before invoking the driver close service.
The suspend case now performs the netif_device_detach to exit the
PRESENT state before the call to bcm_sysport_netif_stop rather than
after it.
These behaviors prevent any future scheduling of the driver timeout
service during the window. The netif_tx_stop_all_queues function
in bcm_sysport_netif_stop is replaced with netif_tx_disable to ensure
synchronization with any transmit or timeout threads that may
already be executing on other cores.
For symmetry, the netif_device_attach call upon resume is moved to
after the call to bcm_sysport_netif_start. Since it wakes the transmit
queues it is not necessary to invoke netif_tx_start_all_queues from
bcm_sysport_netif_start so it is moved into the driver open service.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The AON_PM_L2 is normally used to trigger and identify the source of a
wake-up event. Since the RX_SYS clock is no longer turned off, we also
have an interrupt being sent to the SYSTEMPORT INTRL_2_0 controller, and
that interrupt remains active up until the magic packet detector is
disabled which happens much later during the driver resumption.
The race happens if we have a CPU that is entering the SYSTEMPORT
INTRL2_0 handler during resume, and another CPU has managed to clear the
wake-up interrupt during bcm_sysport_resume_from_wol(). In that case, we
have the first CPU stuck in the interrupt handler with an interrupt
cause that has been cleared under its feet, and so we keep returning
IRQ_NONE and we never make any progress.
This was not a problem before because we would always turn off the
RX_SYS clock during WoL, so the SYSTEMPORT INTRL2_0 would also be turned
off as well, thus not latching the interrupt.
The fix is to make sure we do not enable either the MPD or
BRCM_TAG_MATCH interrupts since those are redundant with what the
AON_PM_L2 interrupt controller already processes and they would cause
such a race to occur.
Fixes: bb9051a2b2 ("net: systemport: Add support for WAKE_FILTER")
Fixes: 83e82f4c70 ("net: systemport: add Wake-on-LAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When inserting the TSB, keep track of how many times we had to do it and
if there was a failure in doing so, this helps profile the driver for
possibly incorrect headroom settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During bcm_sysport_insert_tsb() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can turn on the RX/TX checksum offloads by default and make sure that
those are properly reflected back to e.g: stacked devices such as VLAN
or DSA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver resume and open, the HW may have lost its context/state,
utilize bcm_sysport_set_features() to make sure we do restore the
correct set of features that were previously configured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally enabling TX and RX checksum offloads,
refactor bcm_sysport_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure that
features are correctly programmed during network device registration.
Since we can now be called during register_netdev() with clocks gated,
we need to temporarily turn them on/off in order to have a successful
register programming.
We also move the CRC forward setting read into
bcm_sysport_set_features() since priv->crc_fwd matters while turning on
RX checksum offload, that way we are guaranteed they are in sync in case
we ever add support for NETIF_F_RXFCS at some point in the future.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining caller of this function is inside of an #ifdef
after another caller got removed. This causes a harmless warning
in some configurations:
drivers/net/ethernet/broadcom/bcmsysport.c:1068:13: error: 'bcm_sysport_resume_from_wol' defined but not used [-Werror=unused-function]
Removing the #ifdef around the PM functions simplifies the code
and avoids the problem but letting the compiler drop the unused
functions silently.
Fixes: 9e85e22713 ("net: systemport: Do not re-configure upon WoL interrupt")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT MAC allows up to 8 filters to be programmed to wake-up
from LAN. Verify that we have up to 8 filters and program them to the
appropriate RXCHK entries to be matched (along with their masks).
We need to update the entry and exit to Wake-on-LAN mode to keep the
RXCHK engine running to match during suspend, but this is otherwise
fairly similar to Magic Packet detection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper function to turn on/off MPD, this will be used to avoid
duplicating code as we are going to add additional types of wake-up
types.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already properly resume from Wake-on-LAN whether such a condition
occured or not, no need to process the WoL interrupt for functional
changes since that could race with other settings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT Lite reversed the logic compared to SYSTEMPORT, the
GIB_FCS_STRIP bit is set when the Ethernet FCS is stripped, and that bit
is not set by default. Fix the logic such that we properly check whether
that bit is set or not and we don't forward an extra 4 bytes to the
network stack.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most of these calls we can just pass NULL through to the fallback
function as the sb_dev. The only cases where we cannot are the cases where
we might be dealing with either an upper device or a driver that would
have configured things to support an sb_dev itself.
The only driver that has any significant change in this patch set should be
ixgbe as we can drop the redundant functionality that existed in both the
ndo_select_queue function and the fallback function that was passed through
to us.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes it so that instead of passing a void pointer as the
accel_priv we instead pass a net_device pointer as sb_dev. Making this
change allows us to pass the subordinate device through to the fallback
function eventually so that we can keep the actual code in the
ndo_select_queue call as focused on possible on the exception cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Trivial fix to spelling mistake in netdev_warn warning message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding the DSA notifier, we will be sending DSA notifications with
info->master that is going to point to a particular net_device instance.
Our logic in bcm_sysport_map_queues() correctly disambiguates net_device
instances that are not covered by our own driver, but it will not make
sure that info->master points to a particular driver instance that we
are interested in. In a system where e.g: two or more SYSTEMPORT
instances are registered, this would lead in programming two or more
times the queue mapping, completely messing with the logic which does
the queue/port allocation and tracking.
Fix this by looking at the notifier_block pointer which is unique per
instance and allows us to go back to our driver private structure, and
in turn to the backing net_device instance.
Fixes: d156576362 ("net: systemport: Establish lower/upper queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for introducing adaptive TX to net DIM.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->protocol is a __be16 which we would be calling htons() against,
while this is not wrong per-se as it correctly results in swapping the
value on LE hosts, this still upsets sparse. Adopt a similar pattern to
what other drivers do and just assign ip_ver to skb->protocol, and then
use htons() against the different constants such that the compiler can
resolve the values at build time.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per
interrupt until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had
previously determined instead of the user requested parameters
Fixes: b6e0e87542 ("net: systemport: Implement adaptive interrupt coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive TX coalescing is not currently giving us any advantages and
ends up making the CPU spin more frequently until TX completion. Deny
and disable adaptive TX coalescing for now and rely on static
configuration, we can always add it back later.
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for adaptive RX and TX interrupt coalescing using
net_dim. We have each of our TX ring and our single RX ring implement a
bcm_sysport_net_dim structure which holds an interrupt counter, number
of packets, bytes, and a container for a net_dim instance.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.
This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:
- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
point where we run out of free descriptors, so we stop the transmit
queue at the end of bcm_sysport_xmit()
- because of our locking, we have the transmit process disable
interrupts which means we can be blocking the TX reclamation process
- when TX reclamation finally runs, we will be computing the difference
between ring->c_index (last consumed index by SW) and what the HW
reports through its register
- this register is masked with (ring->size - 1) = 0xff, which will lead
to stripping the upper bits of the index (register is 16-bits wide)
- we will be computing last_tx_cn as 0, which means there is no work to
be done, and we never wake-up the transmit queue, leaving it
permanently disabled
A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Short packet padding added to the driver is only necessary when using
Broadcom tags, but since this is now taken care of net/dsa/tag_brcm.c,
we are guaranteed being given correctly padded packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a documentation mistake, the IPG length was set to 0x12 while it
should have been 12 (decimal). This would affect short packet (64B
typically) performance since the IPG was bigger than necessary.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hesoteric board configurations where port 0 is not available would still
make SYSTEMPORT inspect the switch port 0, queue 0, which, not being
enabled, would cause transmit timeouts over time. Just ignore those
unconfigured rings instead.
Fixes: 84ff33eeb23d ("net: systemport: Establish DSA network device queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the master network device that is signaled through the DSA
notifier is actually going to be ourself, otherwise, we could just be
de-referencing garbage from other drivers.
Fixes: 84ff33eeb23d ("net: systemport: Establish DSA network device queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because SYSTEMPORT is a (semi) normal network device, the stack may attempt to
queue packets on it oustide of the DSA slave transmit path. When that happens,
the DSA layer has not had a chance to tag packets with the appropriate per-port
and per-queue information, and if that happens and we don't have a port 0 queue
0 available (e.g: on boards where this does not exist), we will hit a NULL
pointer de-reference in bcm_sysport_select_queue().
Guard against such cases by testing for the TX ring validity.
Fixes: 84ff33eeb23d ("net: systemport: Establish DSA network device queue mapping")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have established the queue mapping between the switch port
egress queues and the SYSTEMPORT egress queues, we can turn on Advanced
Congestion Buffering (ACB) at the SYSTEMPORT level. This enables the
Ethernet MAC controller to get out of band flow control information
directly from the switch port and queue that it monitors such that its
internal TDMA can be appropriately backpressured.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Establish a queue mapping between the DSA slave network device queues
created that correspond to switch port queues, and the transmit queue
that SYSTEMPORT manages.
We need to configure the SYSTEMPORT transmit queue with the switch port number
and switch port queue number in order for the switch and SYSTEMPORT hardware to
utilize the out of band congestion notification. This hardware mechanism works
by looking at the switch port egress queue and determines whether there is
enough buffers for this queue, with that class of service for a successful
transmission and if not, backpressures the SYSTEMPORT queue that is being used.
For this to work, we implement a notifier which looks at the
DSA_PORT_REGISTER event. When DSA network devices are registered, the
framework calls the DSA notifiers when that happens, extracts the number
of queues for these devices and their associated port number, remembers
that in the driver private structure and linearly maps those queues to
TX rings/queues that we manage.
This scheme works because DSA slave network deviecs always transmit
through SYSTEMPORT so when DSA slave network devices are
destroyed/brought down, the corresponding SYSTEMPORT queues are no
longer used. Also, by design of the DSA framework, the master network
device (SYSTEMPORT) is registered first.
For faster lookups we use an array of up to DSA_MAX_PORTS * number of
queues per port, and then map pointers to bcm_sysport_tx_ring such that
our ndo_select_queue() implementation can just index into that array to
locate the corresponding ring index.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several problems with commit 10377ba767 ("net: systemport:
Support 64bit statistics", first one got fixed in 7095c97345 ("net:
systemport: Fix 64-bit stats deadlock").
The second problem is that this specific code updates the
stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we
are returning to ethtool -S. If we are not running a tool that involves
calling ndo_get_stats64(), then we won't get updated ethtool stats.
The solution to this is to update the stats from both call sites,
factoring that into a specific function, While at it, don't just check
the sizeof() but also the type of the statistics in order to use the
64-bit stats seqlock.
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can enter a deadlock situation because there is no sufficient protection
when ndo_get_stats64() runs in process context to guard against RX or TX NAPI
contexts running in softirq, this can lead to the following lockdep splat and
actual deadlock was experienced as well with an iperf session in the background
and a while loop doing ifconfig + ethtool.
[ 5.780350] ================================
[ 5.784679] WARNING: inconsistent lock state
[ 5.789011] 4.13.0-rc7-02179-g32fae27c725d #70 Not tainted
[ 5.794561] --------------------------------
[ 5.798890] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 5.804971] swapper/0/0 [HC0[0]:SC1[1]:HE0:SE0] takes:
[ 5.810175] (&syncp->seq#2){+.?...}, at: [<c0768a28>] bcm_sysport_tx_reclaim+0x30/0x54
[ 5.818327] {SOFTIRQ-ON-W} state was registered at:
[ 5.823278] bcm_sysport_get_stats64+0x17c/0x258
[ 5.828053] dev_get_stats+0x38/0xac
[ 5.831776] rtnl_fill_stats+0x30/0x118
[ 5.835761] rtnl_fill_ifinfo+0x538/0xe24
[ 5.839921] rtmsg_ifinfo_build_skb+0x6c/0xd8
[ 5.844430] rtmsg_ifinfo_event.part.5+0x14/0x44
[ 5.849201] rtmsg_ifinfo+0x20/0x28
[ 5.852837] register_netdevice+0x628/0x6b8
[ 5.857171] register_netdev+0x14/0x24
[ 5.861051] bcm_sysport_probe+0x30c/0x438
[ 5.865280] platform_drv_probe+0x50/0xb0
[ 5.869418] driver_probe_device+0x2e8/0x450
[ 5.873817] __driver_attach+0x104/0x120
[ 5.877871] bus_for_each_dev+0x7c/0xc0
[ 5.881834] bus_add_driver+0x1b0/0x270
[ 5.885797] driver_register+0x78/0xf4
[ 5.889675] do_one_initcall+0x54/0x190
[ 5.893646] kernel_init_freeable+0x144/0x1d0
[ 5.898135] kernel_init+0x8/0x110
[ 5.901665] ret_from_fork+0x14/0x2c
[ 5.905363] irq event stamp: 24263
[ 5.908804] hardirqs last enabled at (24262): [<c08eecf0>] net_rx_action+0xc4/0x4e4
[ 5.916624] hardirqs last disabled at (24263): [<c0a7da00>] _raw_spin_lock_irqsave+0x1c/0x98
[ 5.925143] softirqs last enabled at (24258): [<c022a7fc>] irq_enter+0x84/0x98
[ 5.932524] softirqs last disabled at (24259): [<c022a918>] irq_exit+0x108/0x16c
[ 5.939985]
[ 5.939985] other info that might help us debug this:
[ 5.946576] Possible unsafe locking scenario:
[ 5.946576]
[ 5.952556] CPU0
[ 5.955031] ----
[ 5.957506] lock(&syncp->seq#2);
[ 5.960955] <Interrupt>
[ 5.963604] lock(&syncp->seq#2);
[ 5.967227]
[ 5.967227] *** DEADLOCK ***
[ 5.967227]
[ 5.973222] 1 lock held by swapper/0/0:
[ 5.977092] #0: (&(&ring->lock)->rlock){..-...}, at: [<c0768a18>] bcm_sysport_tx_reclaim+0x20/0x54
So just remove the u64_stats_update_begin()/end() pair in ndo_get_stats64()
since it does not appear to be useful for anything. No inconsistency was
observed with either ifconfig or ethtool, global TX counts equal the sum of
per-queue TX counts on a 32-bit architecture.
Fixes: 10377ba767 ("net: systemport: Support 64bit statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to how we configure the RSB (Receive Status Block) we also
need to set the TSB (Transmit Status Block) based on the host endian.
This was missing from the commit indicated below.
Fixes: 389a06bc53 ("net: systemport: Set correct RSB endian bits based on host")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSB_SWAP0 needs to match the host CPU endian, and it needs to be set
for LE and clear for BE. RSB_SWAP1 must always be cleared for SYSTEMPORT
Lite.
With these settings, we have the Receive Status Block always match the
host endian and we do not need to perform any conversion. Since there is
not necessarily a CONFIG_CPU_LITTLE_ENDIAN option defined, we test for
!CONFIG_CPU_BIG_ENDIAN which is guaranteed to be set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case bcm_sysport_init_tx_ring() is not able to allocate ring->cbs, we
would return with an error, and call bcm_sysport_fini_tx_ring() and it
would see that ring->cbs is NULL and do nothing. This would leak the
coherent DMA descriptor area, so we need to free it on error before
returning.
Reported-by: Eric Dumazet <edumazet@gmail.com>
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize dev_consume_skb_any(cb->skb) in bcm_sysport_free_cb() which is
used when a TX packet is completed, as well as when the RX ring is
cleaned on shutdown. None of these two cases are packet drops, so be
drop monitor friendly.
Suggested-by: Eric Dumazet <edumazet@gmail.com>
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainline had UFO fixes, but UFO is removed in net-next so we
take the HEAD hunks.
Minor context conflict in bcmsysport statistics bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Broadcom Systemport device in 32bit Platform, ifconfig can
only report up to 4G tx,rx status, which will be wrapped to 0 when the
number of incoming or outgoing packets exceeds 4G, only taking
around 2 hours in busy network environment (such as streaming).
Therefore, it makes hard for network diagnostic tool to get reliable
statistical result, so the patch is used to add 64bit support for
Broadcom Systemport device in 32bit Platform.
This patch provides 64bit statistics capability on both ethtool and ifconfig.
Signed-off-by: Jianming.qiao <kiki-good@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luis Chamberlain