Commit Graph

172 Commits

Author SHA1 Message Date
Mike Christie 913e5bf435 [SCSI] libiscsi, iser, tcp: remove recv_lock
The recv lock was defined so the iscsi layer could block
the recv path from processing IO during recovery. It
turns out iser just set a lock to that pointer which was pointless.

We now disconnect the transport connection before doing recovery
so we do not need the recv lock. For iscsi_tcp we still stop
the recv path incase older tools are being used.

This patch also has iscsi_itt_to_ctask user grab the session lock
and has the caller access the task with the lock or get a ref
to it in case the target is broken and sends a tmf success response
then sends data or a response for the command that was supposed to
be affected bty the tmf.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:22 -05:00
Mike Christie 88dfd340b9 [SCSI] iscsi class: Add session initiatorname and ifacename sysfs attrs.
This adds two new attrs used for creating initiator ports and
binding sessions to hardware.

The session level initiatorname:

Since bnx2i does a scsi_host per host device, we need to add the
iface initiator port settings on the session, so we can create
multiple initiator ports (each with different inames) per device/scsi_host.

The current iname reflects that qla4xxx can have one iname per hba, and we are
allocating a host per session for software. The iname on the host will
remain so we can export and set the hba level qla4xxx setting.

The ifacename attr:

To bind a session to a some peice of hardware in userspace we maintain
some mappings, but during boot or iscsid restart (iscsid contains the user
space part of the driver) we need to be able to figure out which of those
host mappings abstractions maps to certain sessions. This patch adds
a ifacename attr, which userspace can set to id the host side of the
endpoint across pivot_roots and iscsid restarts.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:21 -05:00
Mike Christie 06520edea0 [SCSI] iscsi_tcp: hook iscsi_tcp into iscsi_endpoint code
iscsi_tcp creates its ep in userspace using sockets because
it is virtual, so we just check if we are sent a ep and fail
if we are.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:21 -05:00
Mike Christie 7970634b81 [SCSI] iscsi class: user device_for_each_child instead of duplicating session list
Currently we duplicate the list of sessions, because we were using the
test for if a session was on the host list to indicate if the session
was bound or unbound. We can instead use the target_id and fix up
the class so that drivers like bnx2i do not have to manage the target id
space.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:20 -05:00
Mike Christie 135a8ad4e0 [SCSI] iscsi_tcp: handle iscsi_cmd_task rename
This converts iscsi_tcp to use the iscsi_task name.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:20 -05:00
Mike Christie fbc514b4e2 [SCSI] iscsi_tcp: convert iscsi_tcp to support merged tasks
Convert iscsi_tcp to support merged tasks.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:19 -05:00
Mike Christie 0af967f5d4 [SCSI] libiscsi, iscsi_tcp, iser: add session cmds array accessor
Currently to get a ctask from the session cmd array, you have to
know to use the itt modifier. To make this easier on LLDs and
so in the future we can easilly kill the session array and use
the host shared map instead, this patch adds a nice wrapper
to strip the itt into a session->cmds index and return a ctask.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:18 -05:00
Mike Christie 5d91e209fb [SCSI] iscsi: remove session/conn_data_size from iscsi_transport
This removes the session and conn data_size fields from the iscsi_transport.
Just pass in the value like with host allocation. This patch also makes
it so the LLD iscsi_conn data is allocated with the iscsi_cls_conn.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:16 -05:00
Mike Christie a4804cd6eb [SCSI] iscsi: add iscsi host helpers
This finishes the host/session unbinding, by adding some helpers
to add and remove hosts and the session they manage.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:16 -05:00
Mike Christie 756135215e [SCSI] iscsi: remove session and host binding in libiscsi
bnx2i allocates a host per netdevice but will use libiscsi,
so this unbinds the session from the host in that code.

This will also be useful for the iser parent device dma settings
fixes.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:16 -05:00
Mike Christie d3826721b1 [SCSI] iscsi class, iscsi drivers: remove unused iscsi_transport attrs
max_cmd_len and max_conn are not really used. max_cmd_len is
always 16 and can be set by the LLD. max_conn is always one
since we do not support MCS.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:15 -05:00
Mike Christie 40753caa36 [SCSI] iscsi class, iscsi_tcp/iser: add host arg to session creation
iscsi offload (bnx2i and qla4xx) allocate a scsi host per hba,
so the session creation path needs a shost/host_no argument.
Software iscsi/iser will follow the same behabior as before
where it allcoates a host per session, but in the future iser
will probably look more like bnx2i where the host's parent is
the hardware (rnic for iser and for bnx2i it is the nic), because
it does not use a socket layer like how iscsi_tcp does.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-12 08:22:15 -05:00
Boaz Harrosh 94795b61e8 [SCSI] iscsi: bidi support for iscsi_tcp
access the right scsi_in() and/or scsi_out() side of things.
also for resid

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Reviewed-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-18 11:53:24 -05:00
Mike Christie 322d739da8 [SCSI] iscsi: fix up iscsi printk prefix
Some iscsi class messages have the dev_printk prefix and some libiscsi
and iscsi_tcp messages have "iscsi" or the module name as a prefix which
is normally pretty useless when trying to figure out which session
or connection the message is attached to. This patch adds iscsi lib
and class dev_printks so all messages have a common prefix that
can be used to figure out which object printed it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-07 18:02:37 -06:00
James Bottomley d3f46f39b7 [SCSI] remove use_sg_chaining
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.

Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-30 13:14:02 -06:00
Mike Christie df93ffcd74 [SCSI] iscsi_tcp: fix setting of r2t
If we negotiate for X r2ts we have to use only X r2ts. We cannot
round up (we could send less though). It is ok to fail if it
is not something the driver can handle, so this patch just does
that.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:52 -06:00
Mike Christie 4545a88fc1 [SCSI] iscsi_tcp: hold lock during data rsp processing
iscsi_data_rsp needs to hold the sesison lock when it calls
iscsi_update_cmdsn.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:50 -06:00
Mike Christie 66bbe0ce11 [SCSI] iscsi_tcp: enable sg chaining
The previous patches converted iscsi_tcp to support sg chaining.
This patch sets the proper flags and sets sg_table size to
4096. This allows fs io to be capped at max_sectors, but passthrough
IO to be limited by some other part of the kernel.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:48 -06:00
Mike Christie 7a53dc52a5 [SCSI] iscsi_tcp: drop session when itt does not match any command
A target should never send us a itt that does not match a running
task. If it does we do not really know what is coming down after the header,
unless we evaluate the hdr and do some guessing sometimes. However,
even if we know what is coming we probably do not have buffers for it or we
cannot respond (if it is a r2t for example), so just drop the session.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:45 -06:00
Olaf Kirch 03766a1d4e [SCSI] iscsi_tcp: stop leaking r2t_info's when the incoming R2T is bad
iscsi_r2t_rsp checks the incoming R2T for sanity, and if it
thinks it's fishy, it will drop it silently. In this case, we
leaked an r2t_info object. If we do this often enough, we run
into a BUG_ON some time later.

Removed r2t wrappers and update patch by Mike Christie

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:43 -06:00
Olaf Kirch a8ac6311cc [SCSI] iscsi: convert xmit path to iscsi chunks
Convert xmit to iscsi chunks.

from michaelc@cs.wisc.edu:

Bug fixes, more digest integration, sg chaining conversion and other
sg wrapper changes, coding style sync up, and removal of io fields,
like pdu_sent, that are not needed.

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:42 -06:00
Mike Christie f6d5180c78 [SCSI] libiscsi: fix nop handling
During root boot and shutdown the target could send us nops.
At this time iscsid cannot be running, so the target will drop
the session and the boot or shutdown will hang.

To handle this and allow us to better control when to check the network
this patch moves the nop handling to the kernel.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:35 -06:00
Mike Christie b3a7ea8d50 [SCSI] libiscsi: do not block session during logout
There is not need to block the session during logout. Since
we are going to fail the commands that were blocked just fail them
immediately instead.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:28 -06:00
Olaf Kirch 6320377fd9 [SCSI] libiscsi, iscsi_tcp: iscsi pool cleanup
iscsi_pool_init simplified

iscsi_pool_init currently has a lot of duplicate kfree() calls it does
when some allocation fails. This patch simplifies the code a little by
using iscsi_pool_free to tear down the pool in case of an error.

iscsi_pool_init also returns a copy of the item array to the caller.
Not all callers use this array, so we make it optional.

Instead of allocating a second array and return that, allocate just one
array, of twice the size.

Update users of iscsi_pool_{init,free}

This patch drops the (now useless) second argument to
iscsi_pool_free, and updates all callers.

It also removes the ctask->r2ts array, which was never
used anyway. Since the items argument to iscsi_pool_init
is now optional, we can pass NULL instead.

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:27 -06:00
Boaz Harrosh 004d6530f8 [SCSI] iscsi_tcp, libiscsi: initial AHS Support
at libiscsi generic code
  - currently code assumes a storage space of pdu header is allocated
    at llds ctask and is pointed to by iscsi_cmd_task->hdr. Here I add
    a hdr_max field pertaining to that storage, and an hdr_len that
    accumulates the current use of the pdu-header.

  - Add an iscsi_next_hdr() inline which returns the next free space
    to write new Header at. Also iscsi_next_hdr() is used to retrieve
    the address at which to write the header-digest.

  - Add iscsi_add_hdr(length). What the user do is calls iscsi_next_hdr()
    for address of the new header, than calls iscsi_add_hdr(length) with
    the size of the new header. iscsi_add_hdr() will check if space is
    available and update to the new size. length must be padded according
    to standard.

  - Add 2 padding inline helpers thanks to Olaf. Current patch does not
    use them but Following patches will.
    Also moved definition of ISCSI_PAD_LEN to iscsi_proto.h which had
    PAD_WORD_LEN that was never used anywhere.

  - Let iscsi_prep_scsi_cmd_pdu() signal an Error return since now  it is
    possible that it will fail.

  - I was tired of yet again writing a "this is a digest" comment next to
    sizeof(__u32) so I defined a new ISCSI_DIGEST_SIZE. Now I don't need
    any comments. Changed all places that used sizeof(__u32) or "4" in
    connection to a digest.

  iscsi_tcp specific code
  - At struct iscsi_tcp_cmd_task allocate maximum space allowed in
    standard for all headers following the iscsi_cmd header. and mark
    it so in iscsi_tcp_session_create()
  - At iscsi_send_cmd_hdr() retrieve the correct headers size and
    write header digest at iscsi_next_hdr().

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:23 -06:00
Boaz Harrosh 7207fea452 [SCSI] iscsi: Prettify resid handling and some extra checks
- Check to see that OVERFLOW is not negative indicating
    a bug.
  - Unify handling of UNDERFLOW and OVERFLOW to the same
    code.
  - Also handle BIDI_OVERFLOW.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:22 -06:00
Olaf Kirch da32dd681f [SCSI] iscsi_tcp: rewrite recv path
Rewrite recv path. Fixes:
- data digest processing and error handling.
- ahs support.

Some fixups by Mike Christie

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:20 -06:00
Mike Christie 843c0a8a76 [SCSI] libiscsi, iscsi_tcp: add device support
This patch adds logical unit reset support. This should work for ib_iser,
but I have not finished testing that driver so it is not hooked in yet.

This patch also temporarily reverts the iscsi_tcp r2t write out patch.
That code is completely rewritten in this patchset.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:19 -06:00
Tony Battersby 505f76b306 [SCSI] iscsi_tcp: fix potential lockup with write commands
There is a race condition in iscsi_tcp.c that may cause it to forget
that it received a R2T from the target.  This race may cause a data-out
command (such as a write) to lock up.  The race occurs here:

static int
iscsi_send_unsol_pdu(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask)
{
	struct iscsi_tcp_cmd_task *tcp_ctask = ctask->dd_data;
	int rc;

	if (tcp_ctask->xmstate & XMSTATE_UNS_HDR) {
		BUG_ON(!ctask->unsol_count);
		tcp_ctask->xmstate &= ~XMSTATE_UNS_HDR; <---- RACE
		...

static int
iscsi_r2t_rsp(struct iscsi_conn *conn, struct iscsi_cmd_task *ctask)
{
	...
	tcp_ctask->xmstate |= XMSTATE_SOL_HDR_INIT; <---- RACE
	...

While iscsi_xmitworker() (called from scsi_queue_work()) is preparing to
send unsolicited data, iscsi_tcp_data_recv() (called from
tcp_read_sock()) interrupts it upon receipt of a R2T from the target.
Both contexts do read-modify-write of tcp_ctask->xmstate.  Usually, gcc
on x86 will make &= and |= atomic on UP (not guaranteed of course), but
in this case iscsi_send_unsol_pdu() reads the value of xmstate before
clearing the bit, which causes gcc to read xmstate into a CPU register,
test it, clear the bit, and then store it back to memory.  If the recv
interrupt happens during this sequence, then the XMSTATE_SOL_HDR_INIT
bit set by the recv interrupt will be lost, and the R2T will be
forgotten.

The patch below (against 2.6.24-rc1) converts accesses of xmstate to use
set_bit, clear_bit, and test_bit instead of |= and &=.  I have tested
this patch and verified that it fixes the problem.  Another possible
approach would be to hold a lock during most of the rx/tx setup and
post-processing, and drop the lock only for the actual rx/tx.

Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2007-11-14 14:51:58 -06:00
Herbert Xu 68e3f5dd4d [CRYPTO] users: Fix up scatterlist conversion errors
This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion.  It also adds a few conversions that were
missing altogether.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-27 00:52:07 -07:00
Jens Axboe 642f149031 SG: Change sg_set_page() to take length and offset argument
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.

Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-24 11:20:47 +02:00
Jens Axboe 45711f1af6 [SG] Update drivers to use sg helpers
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-22 21:19:53 +02:00
Mike Christie b6d44fe958 [SCSI] iscsi_tcp: Turn off bounce buffers
It was found by LSI that on setups with large amounts of memory
we were bouncing buffers when we did not need to. If the iscsi tcp
code touches the data buffer (or a helper does),
it will kmap the buffer. iscsi_tcp also does not interact with hardware,
so it does not have any hw dma restrictions. This patch sets the bounce
buffer settings for our device queue so buffers should not be bounced
because of a driver limit.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-27 09:12:54 -04:00
Mike Christie 7974392c0b [SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
This prevents the iscsi modules from being unloaded while
there are active mounts from an iscsi target.

Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-27 09:11:45 -04:00
Al Viro a9204879b4 Fix buggered kmalloc() call argument order
Wrong order of arguments

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20 08:24:49 -07:00
FUJITA Tomonori 1c13899154 [SCSI] iscsi_tcp: convert to use the data buffer accessors
- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

TODO: use scsi_for_each_sg().

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-17 16:01:55 -05:00
Mike Christie d8196ed218 [SCSI] iscsi class, iscsi_tcp, iser, qla4xxx: add netdevname sysfs attr
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:38:04 -04:00
Mike Christie 2223696192 [SCSI] iscsi class, qla4xxx, iscsi_tcp: export local address
This patch exports the local address for the session. For
qla4xxx this is the ip of the hba's port. For software
this is the src addr of the socket.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:37:19 -04:00
Mike Christie 4e7aba73f9 [SCSI] iscsi_tcp: fix fd leak
This patch should fix the file descriptor leak problem. A quick look
through the kernel shows that users of sockfd_lookup use sockfd_put to
release their handle. We were using sock_release which from the comments
and code look like it does not release the get() on the file from the
lookup.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:36:46 -04:00
Mike Christie d1d81c01f4 [SCSI] iscsi_tcp: remove DMA alignment restriction
Add a slave_configure function to iSCSI TCP to remove any DMA
alignment restriction.  This permits the use of direct IO from
arbitrary addresses.

Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:35:36 -04:00
Mike Christie dbdb016d92 [SCSI] iscsi_tcp: fix handling of data buffer padding
If we got the padding, data and header in different skbs,
we were not handling the padding correctly because we attributed it
to the data's skb. This resulted in the initiator reading from
pad bytes + skb offset instead of the correct offset.

If you could not connect with the open solaris target, this
will fix the lock up problem you were hitting.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:35:10 -04:00
Mike Christie 1548271ece [SCSI] libiscsi: make can_queue configurable
This patch allows us to set can_queue and cmds_per_lun from userspace
when we create the session/host. From there we can set it on a per
target basis. The patch fully converts iscsi_tcp, but only hooks
up ib_iser for cmd_per_lun since it currently has a lots of preallocations
based on can_queue.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:46 -04:00
Mike Christie 77a23c21aa [SCSI] libiscsi: fix iscsi cmdsn allocation
The cmdsn allocation and pdu transmit code can race, and we can end
up sending a pdu with cmdsn 10 before a pdu with 5. The target will
then fail the connection/session. This patch fixes the problem by
delaying the cmdsn allocation until we are about to send the pdu.

This also removes the xmitmutex. We were using the connection xmitmutex
during error handling to handle races with mtask and ctask cleanup and
completion. For ctasks we now have nice refcounting and for the mtask,
if we hit the case where the mtask timesout and it is floating
around somewhere in the driver, we end up dropping the session.
And to handle session level cleanup, we use the xmit suspend bit
along with scsi_flush_queue and the session lock to make sure
that the xmit thread is not possibly transmitting a task while
we are trying to kill it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:34:14 -04:00
Mike Christie 218432c680 [SCSI] iscsi tcp: fix iscsi xmit state machine
If iscsi_tcp partially sends a header, it would recalculate the
header size and readd the size of the digest (if header digests
are used).This would cause us to send sizeof(digest) extra bytes
when we sent the rest of the header.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:59:26 -04:00
Mike Christie b2c6416736 [SCSI] iscsi class, iscsi_tcp, ib_iser: add sysfs chap file
The attached patches add sysfs files for the chap settings
to the iscsi transport class, iscsi_tcp and ib_iser. This is
needed for software iscsi because there are times when iscsid
can die and it will need to reread the values it was using.
And it is needed by qla4xxx for basic management opertaions.
This patch does not hook in qla4xxx yet, because I am not sure
the mbx command to use.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:58 -04:00
Mike Christie 857ae0bdb7 [SCSI] iscsi: Some fixes in preparation for bidirectional support - total_length
- Remove shadow of request length from struct iscsi_cmd_task.
- change all users to use scsi_cmnd->request_bufflen directly

(With bidi we will use scsi-ml API to retrieve in/out length)

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:58:22 -04:00
Mike Christie d473cc7f15 [SCSI] iscsi: Some fixes in preparation for bidirectional support - exp_datasn
This patch fixes handling of expected datasn/r2tsn as received from
target. It is done according to: T10 rfc3720 section 3.2.2.3. Data Sequencing.

. unify expected datasn/r2tsn into one counter
. calculate than check expected datasn/r2tsn. On error print a message
  and fail the request. (TODO use iscsi retransmits)
. remove the FIXME   ;)
. avoid zero length memset

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:57:17 -04:00
Mike Christie 8ad5781ae9 [SCSI] iscsi class, qla4xxx, iscsi_tcp, ib_iser: export/set initiator name
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.

For hw iscsi, it is nice to see what the card is using.

This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:56:40 -04:00
Mike Christie 0801c242a3 [SCSI] libiscsi, iscsi_tcp, ib_iser : add sw iscsi host get/set params helpers
iscsid and udev need to key off the hw address being
used so add some helpers for iser and iscsi tcp.

Also convert them

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:55:23 -04:00
Mike Christie 0f238418b6 [SCSI] iscsi_tcp: print useful error message when iscsi crc23c allocation fails
People do not read the README and seem to like to
unselect the crc32c module even though iscsi_tcp selects
it for them. This patch spits a error that tells the user
that they really do need the module. Hopefully, we will
get fewer people asking about this now.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:30:11 -05:00
Mike Christie 8231f0eddb [SCSI] iscsi_tcp: increase max_sectors
For a while now, the block layer has seperated max sectors
and max hw sectors. Software iscsi has no limit so this patch
increases max hw sectors, so we can support large pass through
commands.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:28:49 -05:00
Mike Christie bf32ed33e9 [SCSI] iscsi: rename DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-03-11 11:26:50 -05:00
Al Viro b437735645 [PATCH] iscsi endianness annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-09 09:14:07 -08:00
FUJITA Tomonori 94cb3f822b [SCSI] iscsi: simplify IPv6 and IPv4 address printing
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-06 09:01:38 -06:00
Akinobu Mita 59c17ec169 [SCSI] iscsi: fix crypto_alloc_hash() error check
The return value of crypto_alloc_hash() should be checked by
IS_ERR().

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-06 08:59:52 -06:00
Arne Redlich c959e1c2a4 [SCSI] iscsi: fix 2.6.19 data digest calculation bug
The transition from crypto_digest_*() to  the crypto_hash_*() family
introduced a bug into the data digest calculation: crypto_hash_update() is
called with the number of S/G elements instead of the S/G lists data size.

Signed-off-by: Arne Redlich <arne.redlich@xiranet.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-06 08:59:23 -06:00
Mike Christie db37c505e5 [SCSI] iscsi_tcp: fix xmittask oops
XMSTATE_SOL_HDR could be set when the xmit thread tests it, but there may
not be anything on the r2tqueue yet. Move the XMSTATE_SOL_HDR set
before the addition to the queue to make sure that when we pull something
off it it is valid. This does not add locks around the xmstate test or make
that a atmoic_t because this is a fast path and if it is set when we test it
we can handle it there without the overhead. Later on we check the xmitqueue
for all requests with the session lock so we will not miss it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-10 09:41:48 +09:00
Pete Wyckoff 534284a09b [SCSI] iscsi: always release crypto
Unconditionally free crypto state, as it is always allocated during
TCP connection creation.  Without this, crypto structures leak and
crc32c module refcounts grow as connections are created and
destroyed.

Signed-off-by: Pete Wyckoff <pw@osc.edu>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-10 09:41:40 +09:00
James Bottomley c9802cd957 Merge mulgrave-w:git/scsi-misc-2.6
Conflicts:

	drivers/scsi/iscsi_tcp.c
	drivers/scsi/iscsi_tcp.h

Pretty horrible merge between crypto hash consolidation
and crypto_digest_...->crypto_hash_... conversion

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-23 15:33:43 -05:00
Herbert Xu dc64ddf491 [SCSI] iscsi: Use crypto_hash interface instead of crypto_digest
This patch converts ISCSI to use the new crypto_hash interface instead
of crypto_digest.  It's a fairly straightforward substitution.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2006-09-21 11:46:20 +10:00
Mike Christie ca5186842a [SCSI] iscsi_tcp: fix partial digest recv
When a digest is spread across two network buffers, we currently
ignore this and try to check the digest with the partial buffer.
Or course this fails. This patch has use iscsi_tcp_copy to
copy the whole digest before testing it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:32 -05:00
Mike Christie d5390f5f78 [SCSI] iscsi_tcp: update header size during relogin
When we relogin to a target, we have not yet negotiated digests
so we must reset the hdr_size var.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:25 -05:00
Mike Christie 753e7d3866 [SCSI] iscsi_tcp: fix header resend
This patch built over the last ones fixes a bug in the partial header
resend code, where we add on another 4 bytes to the send length on the resend.
We want just the header plus digest.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:21 -05:00
Mike Christie dd8c0d9586 [SCSI] scsi_tcp: rm data rx and tx tfms
We currently allocated seperate tfms for data and header digests. There
is no reason for this since we can never calculate a rx header and
digest at the same time. Same for sends. So this patch removes the data
tfms and has the send and recv sides use the rx_tfm or tx_tfm.

I also made the connection creation code preallocate the tfms because I
thought I hit a bug where I changed the digests settings during a
relogin but could not allocate the tfm and then we just failed.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:18 -05:00
Mike Christie 62f383003c [SCSI] iscsi_tcp: fix padding, data digests, and IO at weird offsets
iscsi_tcp calculates padding by using the expected transfer length. This
has the problem where if we have immediate data = no and initial R2T =
yes, and the transfer length ended up needing padding then we send:

1. header
2. padding which should have gone after data
3. data

Besides this bug, we also assume the target will always ask for nice
transfer lengths and the first burst length will always be a nice value.
As far as I can tell form the RFC this is not a requirement. It would be
silly to do this, but if someone did it we will end doing bad things.

Finally the last bug in that bit of code is in our handling of the
recalculation of data digests when we do not send a whole iscsi_buf in
one try. The bug here is that we call crypto_digest_final on a
iscsi_sendpage error, then when we send the rest of the iscsi_buf, we
doiscsi_data_digest_init and this causes the previous data digest to be
lost.

And to make matters worse, some of these bugs are replicated over and
over and over again for immediate data, solicited data and unsolicited
data. So the attached patch made over the iscsi git tree (see
kernel.org/git for details) which I updated today to include the patches
I said I merged, consolidates the sending of data, padding and digests
and calculation of data digests and fixes the above bugs.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:14 -05:00
Mike Christie 98a9416af0 [SCSI] attempt to complete r2t with data len greater than max burst
A couple targets like string bean and MDS, send r2ts with
a data len greater than the max burst we agreed to. We
were being strict in our enforcing of the iscsi rfc in that
code path, but there is no driver limitation that prevents
us from fullfilling the request. To allow those targets
to work we will ignore the max_burst length and send as
much data as the target asks for assuming it has consciously
decided to override its max burst length.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:11 -05:00
Mike Christie ffd0436ed2 [SCSI] libiscsi, iscsi_tcp, iscsi_iser: check that burst lengths are valid.
iSCSI RFC states that the first burst length must be smaller than the
max burst length. We currently assume targets will be good, but that may
not be the case, so this patch adds a check.

This patch also moves the unsol data out offset to the lib so the LLDs
do not have to track it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-09-02 13:37:04 -05:00
Mike Christie f4246b33c7 [SCSI] iscsi bugfixes: update and move version number
The version info is useful for iscsi tcp, iser and qla4xxx so move to
transport class.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:50:18 -05:00
Mike Christie 40527afea1 [SCSI] iscsi bugfixes: pass errors from complete_pdu to caller
Must pass ISCSI_ERR values from the recv path and propogate them
upwards.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:49:50 -05:00
Mike Christie c8dc1e523b [SCSI] iscsi bugfixes: reduce memory allocations
We currently try to allocate a max_recv_data_segment_length
which can be very large (default is 64K), and common uses
are up to 1MB. It is very very difficult to allocte this
much contiguous memory and it turns out we never even use it.
We really only need a couple of pages, so this patch has us
allocates just what we know what we need today.

Later if vendors start adding vendor specific data and
we need to handle large buffers we can do this, but for
the last 4 years we have not seen anyone do this or request
it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:49:34 -05:00
Mike Christie 1c83469d36 [SCSI] iscsi bugfixes: fix oops when iser is flushing io
When we enter recovery and flush the running commands
we cannot freee the connection before flushing the commands.
Some commands may have a reference to the connection
that needs to be released before. iscsi_stop was forcing
the term and suspend too early and was causing a oops
in iser, so this patch removes those callbacks all together
and allows the LLD to handle that detail.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:48:32 -05:00
Mike Christie 275fd7d129 [SCSI] iscsi bugfixes: handle data rsp errors
if iscsi_data_rsp fails we must bail out. Since the pdu values like
data length are invalid we cannot continue to process the data since
it could over run buffers.

This fixes a bug with cisco 5428s where that target is sending
too much data.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:48:01 -05:00
Mike Christie b6c395ed03 [SCSI] iscsi bugfixes: fix r2t handling
The iscsi tcp code can pluck multiple rt2s from the tasks's r2tqueue
in the xmit code. This can result in the task being queued on the xmit queue
but gettting completed at the same time.

This patch fixes the above bug by making the fifo a list so
we always remove the entry on the list del.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:47:40 -05:00
Mike Christie d82967c706 [SCSI] iscsi bugfixes: send correct error values to userspace
In the xmit patch we are sending a -EXXX value to iscsi_conn_failure
which is causing userspace to get confused.

We should be sending a ISCSI_ERR_* value that userspace understands.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-07-28 11:47:23 -05:00
Mike Christie 5c75b7fcf0 [SCSI] iscsi: convert iscsi_tcp to new set/get param fns
Convert iscsi_tcp to new lib functions.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-29 11:07:54 -04:00
Mike Christie f70e9c5f91 [SCSI] iscsi: update version to 1.0-595
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-05 19:13:16 -04:00
Mike Christie 3219e52941 [SCSI] iscsi: fix writepsace race
We can race and misset the suspend bit if iscsi_write_space is
called then iscsi_send returns with a failure indicating
there is no space.

To handle this this patch returns a error upwards allowing xmitworker
to decide if we need to try and transmit again. For the no
write space case xmitworker will not retry, and instead
let iscsi_write_space queue it back up if needed (this relies
on the work queue code to properly requeue us if needed).

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-05 19:12:25 -04:00
Mike Christie 67a611149b [SCSI] iscsi: don't switch states when just cleaning up
If recovery failed or we are in recovery only overwrite the state
if we are going to terminate the session or if we logged back in.

STOP_CONN_SUSPEND and conn_cnt are not used. We only support
a single connection session ATM, so cleanup that code while
we are working around it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-06-05 19:10:45 -04:00
Mike Christie e0ecae8da2 [SCSI] iscsi: update version
update version

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-20 09:36:38 -05:00
Mike Christie ffbfe92533 [SCSI] iscsi: kill dtask mempools
Discovered by steven@hayter.me.uk and patch by michaelc@cs.wisc.edu

The dtask mempool is reserving 261120 items per session! Since we are now
sending headers with sendmsg there is no reason for the mempool and that
was causing us to us carzy amounts of mem. We can preallicate a header in
the r2t and task struct and reuse them

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-20 09:35:20 -05:00
Mike Christie 6e458cc943 [SCSI] iscsi: dont use sendpage for iscsi headers
From Zhen and ported by Mike:

Don't use sendpage for the headers. sendpage for the pdu headers
does not seem to have a performance impact, makes life harder
for mutiple data pdus to be in flight and still trips up some
network cards when it is from slab mem.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-20 09:34:21 -05:00
Mike Christie 665b44aee3 [SCSI] iscsi: dequeue all buffers from queue
debugged by wrwhitehead@novell.com
patch and analysis by fujita.tomonori@lab.ntt.co.jp

Only tcp_read_sock and recv_actor (iscsi_tcp_data_recv for us) see
desc.count. It is is used just for permitting tcp_read_sock to read
the portion of data in the socket.

When iscsi_tcp_data_recv sees a partial header, it sets
desc.count. However, it is possible that the next skb (containing the
rest of the header) still does not come. So I'm not sure that this
scheme is completely correct.

Ideally, we should use the exact length of the data in the socket for
desc.count. However, it is not so simple (see SIOCINQ in
tcp_ioctl). So I think that iscsi_tcp_data_recv can just stop playing
with desc.count and tell tcp_read_sock to read the all skbs. As
proposed already, if iscsi_tcp_data_ready sets desc.count to
non-zero, tcp_read_sock does that.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-10 10:13:44 -05:00
Mike Christie 8d2860b3c3 [SCSI] iscsi: increment expstatsn during login
debugged by Ming and Rohan:

The problem Ming and Rohan debugged was that during a normal session
login, open-iscsi is not incrementing the exp_statsn counter. It was
stuck at zero. From the RFC, it looks like if the login response PDU has
a successful status then we should be incrementing that value. Also from
the RFC, it looks like if when we drop a connection then reconnect, we
should be using the exp_statsn from the old connection in the next
relogin attempt.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-10 10:13:21 -05:00
Or Gerlitz be2df72e7e [SCSI] iscsi: align printks
align printk output

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-10 10:12:52 -05:00
Or Gerlitz 264faaaa12 [SCSI] iscsi: add transport end point callbacks
add transport end point callbacks so iscsi drivers that cannot connect
from userspace, like iscsi tcp, using sockets do not have to
implement their own socket infrastructure.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-05-10 10:11:38 -05:00
Mike Christie 5bb0b55a32 [SCSI] iscsi: convert iscsi tcp to libiscsi
This just converts iscsi_tcp to the lib

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-04-14 15:19:42 -05:00
Mike Christie 30a6c65236 [SCSI] iscsi: fix up iscsi eh
The current iscsi_tcp eh is not nicely setup for dm-multipath
and performs some extra task management functions when they
are not needed.

The attached patch:

- Fixes the TMF issues. If a session is rebuilt
then we do not send aborts.

- Fixes the problem where if the host reset fired, we would
return SUCCESS even though we had not really done anything
yet. This ends up causing problem with scsi_error.c's TUR.

- If someone has turned on the userspace nop daemon code to try
and detect network problems before the scsi command timeout
we can now drop and clean up the session before the scsi command
timesout and fires the eh speeding up the time it takes for a
command to go from one patch to another. For network problems
we fail the command with DID_BUS_BUSY so if failfast is set
scsi_decide_disposition fails the command up to dm for it to
try on another path.

- And we had to add some basic iscsi session block code. Previously
if we were trying to repair a session we would retrun a MLQUEUE code
in the queuecommand. This worked but it was not the most efficient
or pretty thing to do since it would take a while to relogin
to the target. For iscsi_tcp/open-iscsi a lot of the iscsi error handler
is in userspace the block code is pretty bare. We will be
adding to that for qla4xxx.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-04-14 14:05:09 -05:00
Mike Christie fd7255f51a [SCSI] iscsi: add sysfs attrs for uspace sync up
For iscsi boot when going from initramfs to the real root we
need to stop the userpsace iscsi daemon. To later restart it
iscsid needs to be able to rebuild itself and part of that
process is matching a session running the kernel with the
iscsid representation. To do this the attached patch
adds several required iscsi values. If the LLD does not provide
them becuase, login is done in userspace, then the transport
class and userspace set ths up for the LLD.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-04-14 14:03:41 -05:00
Mike Christie b5c7a12dc2 [SCSI] iscsi: rm kernel iscsi handles usage for session and connection
from hare@suse.de and michaelc@cs.wisc.edu

hw iscsi like qla4xxx does not allocate a host per session and
for userspace it is difficult to restart iscsid using the
"iscsi handles" for the session and connection, so this
patch just has the class or userspace allocate the id for
the session and connection.

Note: this breaks userspace and requires users to upgrade to the newest
open-iscsi tools. Sorry about his but open-iscsi is still too new to
say we have a stable user-kernel api and we were not good nough
designers to know that other hw iscsi drivers and iscsid itself would
need such changes. Actually we sorta did but at the time we did not
have the HW available to us so we could only guess.

Luckily, the only tools hooking into the class are the open-iscsi ones
or other tools like iscsitart hook into the open-iscsi engine from
userspace or prgroams like anaconda call our tools so they are not affected.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-04-14 14:02:43 -05:00
Matthew Dobson 93d2341c75 [PATCH] mempool: use mempool_create_slab_pool()
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.

Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-26 08:57:00 -08:00
Christoph Lameter ac2b898ca6 [PATCH] slab: Remove SLAB_NO_REAP option
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure.  However, that is not what happens.  The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap().  Cache_reap()
is run every few seconds independently of memory pressure.

Could we remove the whole thing?  Its only used by three slabs anyways and
I cannot find a reason for having this option.

There is an additional problem with SLAB_NO_REAP.  If set then the recovery
of objects from alien caches is switched off.  Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk.  (Strangely __cache_shrink does not
check for SLAB_NO_REAP)

Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-22 07:53:59 -08:00
Mike Christie b36ae07cb7 [SCSI] iscsi update: fix mgmt pool err path release
>From ogerlitz@voltaire.com:

mgmtpool shoild be frees in immdata_alloc_fail label.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-04 16:19:53 -06:00
Mike Christie 351f739e68 [SCSI] iscsi update: set correct state at creation time
>From erezz@voltaire.com:

We are still in ISCSI_STATE_FREE state at create time. The addition
of the first connection puts us in ISCSI_STATE_LOGGED_IN.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-04 16:19:31 -06:00
Mike Christie 1fd459e367 [SCSI] iscsi update: rm conn lock
>From erezz@voltaire.com:

rm conn->lock since it is not used anymore. The dataqueue is protected
by the session lock and xmitmutex.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-04 16:19:08 -06:00
Mike Christie 7b7232f3fb [SCSI] iscsi update: cleanup iscsi class interface
From:
michaelc@cs.wisc.edu
fujita.tomonori@lab.ntt.co.jp
da-x@monatomic.org

and err path fixup from:
ogerlitz@voltaire.com

This patch cleans up that interface by having the lld and class
pass a iscsi_cls_session or iscsi_cls_conn between each other when
the function is used by HW and SW iscsi llds. This way the lld
does not have to remember if it has to send a handle or pointer
and a handle or pointer to connection, session or host.

This also has the class verify the session handle that gets passed from
userspace instead of using the pointer passed into the kernel directly.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-02-04 16:17:03 -06:00
Arjan van de Ven 858119e159 [PATCH] Unlinline a bunch of other functions
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb

Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-01-14 18:27:06 -08:00
Mike Christie a1e80c20e1 [SCSI] iscsi: use pageslab
From: FUJITA Tomonori <tomof@acm.org> and zhenyu.z.wang@intel.com:

We cannot handle filesystems like XFS becuase of the pages they
are sending us. We had thought page_count could be used to
work around this, but the correct test is for PageSlab.

The proper solution is to figure out what type of pages
filesystems can use so we do not have to add tests like
this or handle it in the block layer for all network block drivers
but the issue still has not been resolved on fs-devel
so we are sending this patch as a temporary fix.

This is last patch just in case it is Nakd with the explanation
that we need to push the correct fix through fs-devel, mm
or the block layer. The rest of the patchset can live without
the patch, but the driver will not work with filesystems like
XFS.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:22 -06:00
Mike Christie 55e3299d9e [SCSI] iscsi: fix 4k stack iscsi setups
When we run the xmit code from queuecomand the stack trace
gets too deep. The patch runs the xmit code from the scsi_host
work queue. This fixes 4k stack and xfs support and should
fix the st and sg stack usage bugs.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:21 -06:00
Mike Christie 7b8631b53b [SCSI] iscsi: seperate iscsi interface from setup functions
This is the second version of the patch to address Christoph's comments.
Instead of doing the lib, I just kept everything in scsi_trnapsort_iscsi.c
like the FC and SPI class. This was becuase the driver model and sysfs
class is tied to the session and connection setup so separating did not
buy very much at this time.

The reason for this patch was becuase HW iscsi LLDs like qla4xxx cannot
use the iscsi class becuase the scsi_host was tied to the interface and
class code. This patch just seperates the session from scsi host so
that LLDs that allocate the host per some resource like pci device
can still use the class.

This is also fixes a couple refcount bugs that can be triggered
when users have a sysfs file open, close the session, then
read or write to the file.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:20 -06:00
Mike Christie 7cae5159dd [SCSI] iscsi: add high mem support
From Mike Christie <michaelc@cs.wisc.edu> and FUJITA Tomonori <tomof@acm.org>:

We cannot use page_address becuase some pages could be highmem.
Instead, we can use sock_no_sendpage which does kmap for us.

Signed-off-by: Alex Aizman <itn780@yahoo.com>
Signed-off-by: Dmitry Yusupov <dmitry_yus@yahoo.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-01-14 10:55:18 -06:00