This change does not change any outward behavior; it merely chops down
some large if-conditions with embedded assignments into something a
little more maintainable for others (I of course never had a problem
with this...).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pvrusb2 driver has a concept of "routing scheme" which defines
which physical inputs should be connected based on application's
choice of logical input. The correct "routing scheme" depends on the
specific device since different devices might wire up their muxes
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change default frequency to be US Broadcast channel 3 - with the
transition to d igital the previous value has now become useless.
This change is PURELY to help with my testing (I need to set some kind
of default so it might as well be some thing usable).
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 module's VBI initialization logic uses the current video
standard as part of its internal algorithm. This therefore means that
we probably need to make sure that the correct video standard has been
set before initializing VBI. (Normally we would not care about VBI,
but as described in an earlier changeset, VBI must be initialized
correctly on the cx25840 in order for the chip's hardware scaler to
operate correctly.)
It's kind of messy to force the video standard to be set before
initializing VBI (mainly because we can't know what the app really
wants that early in the initialization process). So this patch does
the next best thing: VBI is re-initialized after any point where the
video standard has been set.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cx25840 module requires that its VBI initialization entry point be
called in order for hardware-scaled video capture to work properly -
even if we don't care about VBI. Making this behavior even more
subtle is that if the capture resolution is set to 720x480 - which is
the default that the pvrusb2 driver sets up - then the cx25840
bypasses the hardware scaler. Therefore this problem does not
manifest itself until some other resolution, e.g. 640x480, is tried.
MythTV typically defaults to 640x480 or 480x480, which means that
things break whenever the driver is used with MythTV.
This all has been known for a while (since at least Nov 2006), but
recent changes in the pvrusb2 driver (specifically in regards to
sub-device support) caused this to break again. VBI initialization
must happen *after* the chip's firmware is loaded, not before. With
this fix, 24xxx devices work correctly again.
A related fix that is part of this changeset is that now we
re-initialize VBI any time after we issue a reset to the cx25840
driver. Issuing a chip reset erases the state that the VBI setup
previously did. Until the HVR-1950 came along this subtlety went
unnoticed, because the pvrusb2 driver previously never issued such a
reset. But with the HVR-1950 we have to do that reset in order to
correctly transition from digital back to analog mode - and since the
HVR-1950 always starts in digital mode (required for the DVB side to
initialize correctly) then this device has never had a chance to work
correctly in analog mode! Analog capture on the HVR-1950 has been
broken this *ENTIRE* time. I had missed it until now because I've
usually been testing at the default 720x480 resolution which does not
require scaling... What fun. By re-initializing VBI after a cx25840
chip reset, correct behavior is restored.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Ensure we specify I/F's for all bandwidths
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the ir-kbd-i2c driver has been converted to a new-style i2c
driver, we can instantiate the ir_video I2C device by default. The
pvr2_disable_ir_video is kept to disable the IR receiver, either
because the user doesn't use it, or for debugging purpose.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
... else DVB-T tuning will not work.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c core used to maintain a list of client for each adapter. This
is a duplication of what the driver core already does, so this list
will be removed as part of a future cleanup. Anyone using this list
must stop doing so.
For pvrusb2, I propose the following change, which should lead to an
equally informative output. The only difference is that i2c clients
which are not a v4l2 subdev won't show up, but I guess this case is
not supposed to happen anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kick up the pvrusb2 version number advertised through the v4l
interface. This value really has almost no meaning because I don't
make a serious attempt to version the driver in this manner (otherwise
this one line becomes a nasty hotspot of changes and merge
conflicts). The value that is here is really a historical thing.
However Hans Verkuil thought it might be a good idea to bump up the
number anyway right now since the driver's mechanism for communicating
with the v4l core has pretty much completely changed. Sending out a
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sets the disable_autoload_ir_video module option to being set,
which disables any attempt by the driver to autoload IR support. This
changes preserves previous behavior, for now. This change can be set
back concurrent with other changes that finally update i2c-kbd-i2c to
use the new i2c binding model.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-kbd-i2c module is about to be updated to match the new style
i2c binding model. These pvrusb2 changes maintain compatibility with
that change. Note that this does not actually break anything even
without the expected ir-kbd-i2c changes yet because previously the
pvrusb2 didn't autoload ir-kbd-i2c anyway.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change defines all possible "IR schemes" related to the pvrusb2
driver, on a per-device basis. That information is then set according
to the hardware in use. The idea here is to make possible a more
intelligent future decision on which, if any, IR receiver driver might
be loaded during initialization.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Wireless USB endpoint state has a sequence number and a current
window and not just a single toggle bit. So allow HCDs to provide a
endpoint_reset method and call this or clear the software toggles as
required (after a clear halt, set configuration etc.).
usb_settoggle() and friends are then HCD internal and are moved into
core/hcd.h and all device drivers call usb_reset_endpoint() instead.
If the device endpoint state has been reset (with a clear halt) but
the host endpoint state has not then subsequent data transfers will
not complete. The device will only work again after it is reset or
disconnected.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The client_register and client_unregister methods are optional so
there is no point in defining stub ones. Especially when these methods
are likely to be removed soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is no longer needed to use a struct pointer as argument, since v4l2_subdev
doesn't require that ioctl-like approach anymore. Instead just pass the input,
output and config (new!) arguments directly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The functions v4l2_i2c_new_subdev and v4l2_i2c_new_probed_subdev relied on
i2c_get_adapdata to return the v4l2_device. However, this is not always
possible on embedded platforms. So modify the API to pass the v4l2_device
pointer explicitly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s_std didn't belong in the tuner ops. Stricly speaking it should be part of
the video ops, but it is used by audio and tuner devices as well, so it is
more efficient to make it part of the core ops.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The init callback was used in several places to load firmware. Make a separate
load_fw callback for that. This makes the code a lot more understandable.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Any time a struct (especially one not defined by this driver) is
allocated, we MUST zero its underlying storage. This makes our usage
of the struct predictable and robust against future changes where
fields might be added that we don't know about. Failing to do this
with tuner_setup left the config field uninitialized which then caused
trouble with the tuner type used for HVR-1950 devices.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Forgot to include the tda9887 component when moving to v4l2-subdev. I
got fooled because its name is "tuner", the same as the tuner module.
Silly me.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove ancient IVTV_IOC_G_CODEC and IVTV_IOC_S_CODEC ioctl functions
from the pvrusb2 driver. These are very very old, were non-standard,
and were only present to keep MythTV happy (their implementation did
nothing except to report success). That was long ago; no recent
versions of MythTV should require this anymore.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change removes the old i2c module controlling layer from the
pvrusb2 driver. This is code that first had appeared in the driver
back in December 2005. It's history. Now we use v4l2-subdev. Please
note also that with this change, the driver will no longer be usable
in kernels older that 2.6.22.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2-subdev infrastructure requires that an initialization call
must be issued to all attached sub-devices before normal operation can
start. This change satisfies that requirement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a pvrusb2 driver instance first initializes, we need to be sure
to send out a complete state update for everything to all attached
modules. The old i2c layer did this by keeping a separate mask of
"stale" bits for each attached module - and setting that mask to all
stale when that module attaches. But the new sub-device adaptation
I've implemented here no longer has per-module stale bits. So instead
there's now a global "force dirty" bit that is set upon instance
initialization, before the sub-devices are attached. After the first
update, this bit is cleared, allowing for normal update-on-dirty
behavior. In this manner, we ensure that all sub-devices have been
properly synchronized at initialization.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner sub-device isn't going to work very well unless we tell it
the correct tuner type to use...
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sub-device update mechanism relies on various "dirty" bits in the
driver in order to know what pieces of state need to be propagated out
to the various sub-devices. But that won't work if the dirty bits are
cleared before the update gets a chance to run. This change ensures
that the update takes place before the dirty bits are cleared.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A sub-device won't successfully attach to our I2C adapter if its class
isn't set to zero. Right the class is still set to
I2C_CLASS_TV_ANALOG in order to allow the old mechanism to still
work. This change temporarily sets the class to zero during the
interval when the sub-device attaches. This code will get removed
when the old i2c layer is finally removed from the driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely