pHyp can change cache nodes for suspend/resume operation. Currently the
device tree is updated by drmgr in userspace after all non boot CPUs are
enabled. Hence, we do not modify the cache list based on the latest cache
nodes. Also we do not remove cache entries for the primary CPU.
This patch removes the cache list for the boot CPU, updates the device tree
before enabling nonboot CPUs and adds cache list for the boot cpu.
This patch also has the side effect that older versions of drmgr will
perform a second device tree update from userspace. While this is a
redundant waste of a couple cycles it is harmless since firmware returns the
same data for the subsequent update-nodes/properties rtas calls.
Signed-off-by: Haren Myneni <hbabu@us.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Detect and recover from machine check when inside opal on a special
scom load instructions. On specific SCOM read via MMIO we may get a machine
check exception with SRR0 pointing inside opal. To recover from MC
in this scenario, get a recovery instruction address and return to it from
MC.
OPAL will export the machine check recoverable ranges through
device tree node mcheck-recoverable-ranges under ibm,opal:
# hexdump /proc/device-tree/ibm,opal/mcheck-recoverable-ranges
0000000 0000 0000 3000 2804 0000 000c 0000 0000
0000010 3000 2814 0000 0000 3000 27f0 0000 000c
0000020 0000 0000 3000 2814 xxxx xxxx xxxx xxxx
0000030 llll llll yyyy yyyy yyyy yyyy
...
...
#
where:
xxxx xxxx xxxx xxxx = Starting instruction address
llll llll = Length of the address range.
yyyy yyyy yyyy yyyy = recovery address
Each recoverable address range entry is (start address, len,
recovery address), 2 cells each for start and recovery address, 1 cell for
len, totalling 5 cells per entry. During kernel boot time, build up the
recovery table with the list of recovery ranges from device-tree node which
will be used during machine check exception to recover from MMIO SCOM UE.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch reverts my previous "fix", and replace it with the correct
fix from Russell.
And as Russell pointed out -- dma_set_mask_and_coherent() (and the other
dma_set_mask() functions) are really supposed to be used by drivers
only.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 64bit relocation code places a few symbols in the text segment.
These symbols are only 4 byte aligned where they need to be 8 byte
aligned. Add an explicit alignment.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we fork/clone we currently don't copy any of the TM state to the new
thread. This results in a TM bad thing (program check) when the new process is
switched in as the kernel does a tmrechkpt with TEXASR FS not set. Also, since
R1 is from userspace, we trigger the bad kernel stack pointer detection. So we
end up with something like this:
Bad kernel stack pointer 0 at c0000000000404fc
cpu 0x2: Vector: 700 (Program Check) at [c00000003ffefd40]
pc: c0000000000404fc: restore_gprs+0xc0/0x148
lr: 0000000000000000
sp: 0
msr: 9000000100201030
current = 0xc000001dd1417c30
paca = 0xc00000000fe00800 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/2
WARNING: exception is not recoverable, can't continue
The below fixes this by flushing the TM state before we copy the task_struct to
the clone. To do this we go through the tmreclaim patch, which removes the
checkpointed registers from the CPU and transitions the CPU out of TM suspend
mode. Hence we need to call tmrechkpt after to restore the checkpointed state
and the TM mode for the current task.
To make this fail from userspace is simply:
tbegin
li r0, 2
sc
<boom>
Kudos to Adhemerval Zanella Neto for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: Adhemerval Zanella Neto <azanella@br.ibm.com>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new ELFv2 little-endian ABI increases the stack redzone -- the
area below the stack pointer that can be used for storing data --
from 288 bytes to 512 bytes. This means that we need to allow more
space on the user stack when delivering a signal to a 64-bit process.
To make the code a bit clearer, we define new USER_REDZONE_SIZE and
KERNEL_REDZONE_SIZE symbols in ptrace.h. For now, we leave the
kernel redzone size at 288 bytes, since increasing it to 512 bytes
would increase the size of interrupt stack frames correspondingly.
Gcc currently only makes use of 288 bytes of redzone even when
compiling for the new little-endian ABI, and the kernel cannot
currently be compiled with the new ABI anyway.
In the future, hopefully gcc will provide an option to control the
amount of redzone used, and then we could reduce it even more.
This also changes the code in arch_compat_alloc_user_space() to
preserve the expanded redzone. It is not clear why this function would
ever be used on a 64-bit process, though.
Signed-off-by: Paul Mackerras <paulus@samba.org>
CC: <stable@vger.kernel.org> [v3.13]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The branch target should be the func addr, not the addr of func_descr_t.
So using ppc_function_entry() to generate the right target addr.
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In copy_oldmem_page, the current check using max_pfn and min_low_pfn to
decide if the page is backed or not, is not valid when the memory layout is
not continuous.
This happens when running as a QEMU/KVM guest, where RTAS is mapped higher
in the memory. In that case max_pfn points to the end of RTAS, and a hole
between the end of the kdump kernel and RTAS is not backed by PTEs. As a
consequence, the kdump kernel is crashing in copy_oldmem_page when accessing
in a direct way the pages in that hole.
This fix relies on the memblock's service memblock_is_region_memory to
check if the read page is part or not of the directly accessible memory.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We possiblly detect EEH errors during reboot, particularly in kexec
path, but it's impossible for device drivers and EEH core to handle
or recover them properly.
The patch registers one reboot notifier for EEH and disable EEH
subsystem during reboot. That means the EEH errors is going to be
cleared by hardware reset or second kernel during early stage of
PCI probe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch cleans up variable eeh_subsystem_enabled so that we needn't
refer the variable directly from external. Instead, we will use
function eeh_enabled() and eeh_set_enable() to operate the variable.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing a lot of hits in the VDSO that are not resolved by perf.
A while(1) gettimeofday() loop shows the issue:
27.64% [vdso] [.] 0x000000000000060c
22.57% [vdso] [.] 0x0000000000000628
16.88% [vdso] [.] 0x0000000000000610
12.39% [vdso] [.] __kernel_gettimeofday
6.09% [vdso] [.] 0x00000000000005f8
3.58% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
2.94% [vdso] [.] __kernel_datapage_offset
2.90% test [.] main
We are using a stripped VDSO image which means only symbols with
relocation info can be resolved. There isn't a lot of point to
stripping the VDSO, the debug info is only about 1kB:
4680 arch/powerpc/kernel/vdso64/vdso64.so
5815 arch/powerpc/kernel/vdso64/vdso64.so.dbg
By using the unstripped image, we can resolve all the symbols in the
VDSO and the perf profile data looks much better:
76.53% [vdso] [.] __do_get_tspec
12.20% [vdso] [.] __kernel_gettimeofday
5.05% [vdso] [.] __get_datapage
3.20% test [.] main
2.92% test [.] 00000037.plt_call.gettimeofday@@GLIBC_2.18
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Guenter Roeck has got the following call trace on a p2020 board:
Kernel stack overflow in process eb3e5a00, r1=eb79df90
CPU: 0 PID: 2838 Comm: ssh Not tainted 3.13.0-rc8-juniper-00146-g19eca00 #4
task: eb3e5a00 ti: c0616000 task.ti: ef440000
NIP: c003a420 LR: c003a410 CTR: c0017518
REGS: eb79dee0 TRAP: 0901 Not tainted (3.13.0-rc8-juniper-00146-g19eca00)
MSR: 00029000 <CE,EE,ME> CR: 24008444 XER: 00000000
GPR00: c003a410 eb79df90 eb3e5a00 00000000 eb05d900 00000001 65d87646 00000000
GPR08: 00000000 020b8000 00000000 00000000 44008442
NIP [c003a420] __do_softirq+0x94/0x1ec
LR [c003a410] __do_softirq+0x84/0x1ec
Call Trace:
[eb79df90] [c003a410] __do_softirq+0x84/0x1ec (unreliable)
[eb79dfe0] [c003a970] irq_exit+0xbc/0xc8
[eb79dff0] [c000cc1c] call_do_irq+0x24/0x3c
[ef441f20] [c00046a8] do_IRQ+0x8c/0xf8
[ef441f40] [c000e7f4] ret_from_except+0x0/0x18
--- Exception: 501 at 0xfcda524
LR = 0x10024900
Instruction dump:
7c781b78 3b40000a 3a73b040 543c0024 3a800000 3b3913a0 7ef5bb78 48201bf9
5463103a 7d3b182e 7e89b92e 7c008146 <3ba00000> 7e7e9b78 48000014 57fff87f
Kernel panic - not syncing: kernel stack overflow
CPU: 0 PID: 2838 Comm: ssh Not tainted 3.13.0-rc8-juniper-00146-g19eca00 #4
Call Trace:
The reason is that we have used the wrong register to calculate the
ksp_limit in commit cbc9565ee8 (powerpc: Remove ksp_limit on ppc64).
Just fix it.
As suggested by Benjamin Herrenschmidt, also add the C prototype of the
function in the comment in order to avoid such kind of errors in the
future.
Cc: stable@vger.kernel.org # 3.12
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the support for to create a direct iommu "bypass"
window on IODA2 bridges (such as Power8) allowing to bypass iommu
page translation completely for 64-bit DMA capable devices, thus
significantly improving DMA performances.
Additionally, this adds a hook to the struct iommu_table so that
the IOMMU API / VFIO can disable the bypass when external ownership
is requested, since in that case, the device will be used by an
environment such as userspace or a KVM guest which must not be
allowed to bypass translations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We expose a number of OF properties in the kexec and crash dump code
and these need to be big endian.
Cc: stable@vger.kernel.org # v3.13
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We would allocate one specific exception stack for each kind of
non-base exceptions for every CPU. For ppc32 the CPU hard ID is
used as the subscript to get the specific exception stack for
one CPU. But for an UP kernel, there is only one element in the
each kind of exception stack array. We would get stuck if the
CPU hard ID is not equal to '0'. So in this case we should use the
subscript '0' no matter what the CPU hard ID is.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Relocation's code is not working in little endian mode because the r_info
field, which is a 64 bits value, should be read from the right offset.
The current code is optimized to read the r_info field as a 32 bits value
starting at the middle of the double word (offset 12). When running in LE
mode, the read value is not correct since only the MSB is read.
This patch removes this optimization which consist to deal with a 32 bits
value instead of a 64 bits one. This way it works in big and little endian
mode.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit f5c57710dd ("powerpc/eeh: Use
partial hotplug for EEH unaware drivers") introduces eeh_rmv_device,
which may grab a reference to a driver, but not release it.
That prevents a driver from being removed after it has gone through EEH
recovery.
This patch drops the reference if it was taken.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
two s390 guest features that need some handling in the host,
and all the PPC changes. The PPC changes include support for
little-endian guests and enablement for new POWER8 features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=yd0Z
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"Second batch of KVM updates. Some minor x86 fixes, two s390 guest
features that need some handling in the host, and all the PPC changes.
The PPC changes include support for little-endian guests and
enablement for new POWER8 features"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (45 commits)
x86, kvm: correctly access the KVM_CPUID_FEATURES leaf at 0x40000101
x86, kvm: cache the base of the KVM cpuid leaves
kvm: x86: move KVM_CAP_HYPERV_TIME outside #ifdef
KVM: PPC: Book3S PR: Cope with doorbell interrupts
KVM: PPC: Book3S HV: Add software abort codes for transactional memory
KVM: PPC: Book3S HV: Add new state for transactional memory
powerpc/Kconfig: Make TM select VSX and VMX
KVM: PPC: Book3S HV: Basic little-endian guest support
KVM: PPC: Book3S HV: Add support for DABRX register on POWER7
KVM: PPC: Book3S HV: Prepare for host using hypervisor doorbells
KVM: PPC: Book3S HV: Handle new LPCR bits on POWER8
KVM: PPC: Book3S HV: Handle guest using doorbells for IPIs
KVM: PPC: Book3S HV: Consolidate code that checks reason for wake from nap
KVM: PPC: Book3S HV: Implement architecture compatibility modes for POWER8
KVM: PPC: Book3S HV: Add handler for HV facility unavailable
KVM: PPC: Book3S HV: Flush the correct number of TLB sets on POWER8
KVM: PPC: Book3S HV: Context-switch new POWER8 SPRs
KVM: PPC: Book3S HV: Align physical and virtual CPU thread numbers
KVM: PPC: Book3S HV: Don't set DABR on POWER8
kvm/ppc: IRQ disabling cleanup
...
The code in remove_cache_dir() is supposed to remove the "cache"
subdirectory from the sysfs directory for a CPU when that CPU is
being offlined. It tries to do this by calling kobject_put() on
the kobject for the subdirectory. However, the subdirectory only
gets removed once the last reference goes away, and the reference
being put here may well not be the last reference. That means
that the "cache" subdirectory may still exist when the offlining
operation has finished. If the same CPU subsequently gets onlined,
the code tries to add a new "cache" subdirectory. If the old
subdirectory has not yet been removed, we get a WARN_ON in the
sysfs code, with stack trace, and an error message printed on the
console. Further, we ultimately end up with an online cpu with no
"cache" subdirectory.
This fixes it by doing an explicit kobject_del() at the point where
we want the subdirectory to go away. kobject_del() removes the sysfs
directory even though the object still exists in memory. The object
will get freed at some point in the future. A subsequent onlining
operation can create a new sysfs directory, even if the old object
still exists in memory, without causing any problems.
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
smt-snooze-delay was designed to disable NAP state or delay the entry
to the NAP state prior to adoption of cpuidle framework. This
is per-cpu variable. With the coming of CPUIDLE framework,
states can be disabled on per-cpu basis using the cpuidle/enable
sysfs entry.
Also, with the coming of cpuidle driver each state's target residency
is per-driver unlike earlier which was per-device. Therefore,
the per-cpu sysfs smt-snooze-delay which decides the target residency
of the idle state on a particular cpu causes more confusion to the user
as we cannot have different smt-snooze-delay (target residency)
values for each cpu.
In the current code, smt-snooze-delay functionality is completely broken.
It makes sense to remove smt-snooze-delay from idle driver with the
coming of cpuidle framework.
However, sysfs files are retained as ppc64_util currently
utilises it. Once we fix ppc64_util, propose to clean
up the kernel code.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit d31626f70b ("powerpc: Don't corrupt transactional state when
using FP/VMX in kernel") introduced a bug where the uc_link and uc_regs
fields of the ucontext_t that is created to hold the transactional
values of the registers in a 32-bit signal frame didn't get set
correctly. The reason is that we now clear the MSR_TS bits in the MSR
in save_tm_user_regs(), before the code that sets uc_link and uc_regs.
To fix this, we move the setting of uc_link and uc_regs into the same
if statement that selects whether to call save_tm_user_regs() or
save_user_regs().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes a logic error that caused a failure to update the hw breakpoint
registers when not using the hw-breakpoint interface.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
Add new state for transactional memory (TM) to kvm_vcpu_arch. Also add
asm-offset bits that are going to be required.
This also moves the existing TFHAR, TFIAR and TEXASR SPRs into a
CONFIG_PPC_TRANSACTIONAL_MEM section. This requires some code changes to
ensure we still compile with CONFIG_PPC_TRANSACTIONAL_MEM=N. Much of the added
the added #ifdefs are removed in a later patch when the bulk of the TM code is
added.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix merge conflict]
Signed-off-by: Alexander Graf <agraf@suse.de>
We create a guest MSR from scratch when delivering exceptions in
a few places. Instead of extracting LPCR[ILE] and inserting it
into MSR_LE each time, we simply create a new variable intr_msr which
contains the entire MSR to use. For a little-endian guest, userspace
needs to set the ILE (interrupt little-endian) bit in the LPCR for
each vcpu (or at least one vcpu in each virtual core).
[paulus@samba.org - removed H_SET_MODE implementation from original
version of the patch, and made kvmppc_set_lpcr update vcpu->arch.intr_msr.]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The DABRX (DABR extension) register on POWER7 processors provides finer
control over which accesses cause a data breakpoint interrupt. It
contains 3 bits which indicate whether to enable accesses in user,
kernel and hypervisor modes respectively to cause data breakpoint
interrupts, plus one bit that enables both real mode and virtual mode
accesses to cause interrupts. Currently, KVM sets DABRX to allow
both kernel and user accesses to cause interrupts while in the guest.
This adds support for the guest to specify other values for DABRX.
PAPR defines a H_SET_XDABR hcall to allow the guest to set both DABR
and DABRX with one call. This adds a real-mode implementation of
H_SET_XDABR, which shares most of its code with the existing H_SET_DABR
implementation. To support this, we add a per-vcpu field to store the
DABRX value plus code to get and set it via the ONE_REG interface.
For Linux guests to use this new hcall, userspace needs to add
"hcall-xdabr" to the set of strings in the /chosen/hypertas-functions
property in the device tree. If userspace does this and then migrates
the guest to a host where the kernel doesn't include this patch, then
userspace will need to implement H_SET_XDABR by writing the specified
DABR value to the DABR using the ONE_REG interface. In that case, the
old kernel will set DABRX to DABRX_USER | DABRX_KERNEL. That should
still work correctly, at least for Linux guests, since Linux guests
cope with getting data breakpoint interrupts in modes that weren't
requested by just ignoring the interrupt, and Linux guests never set
DABRX_BTI.
The other thing this does is to make H_SET_DABR and H_SET_XDABR work
on POWER8, which has the DAWR and DAWRX instead of DABR/X. Guests that
know about POWER8 should use H_SET_MODE rather than H_SET_[X]DABR, but
guests running in POWER7 compatibility mode will still use H_SET_[X]DABR.
For them, this adds the logic to convert DABR/X values into DAWR/X values
on POWER8.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds fields to the struct kvm_vcpu_arch to store the new
guest-accessible SPRs on POWER8, adds code to the get/set_one_reg
functions to allow userspace to access this state, and adds code to
the guest entry and exit to context-switch these SPRs between host
and guest.
Note that DPDES (Directed Privileged Doorbell Exception State) is
shared between threads on a core; hence we store it in struct
kvmppc_vcore and have the master thread save and restore it.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
On a threaded processor such as POWER7, we group VCPUs into virtual
cores and arrange that the VCPUs in a virtual core run on the same
physical core. Currently we don't enforce any correspondence between
virtual thread numbers within a virtual core and physical thread
numbers. Physical threads are allocated starting at 0 on a first-come
first-served basis to runnable virtual threads (VCPUs).
POWER8 implements a new "msgsndp" instruction which guest kernels can
use to interrupt other threads in the same core or sub-core. Since
the instruction takes the destination physical thread ID as a parameter,
it becomes necessary to align the physical thread IDs with the virtual
thread IDs, that is, to make sure virtual thread N within a virtual
core always runs on physical thread N.
This means that it's possible that thread 0, which is where we call
__kvmppc_vcore_entry, may end up running some other vcpu than the
one whose task called kvmppc_run_core(), or it may end up running
no vcpu at all, if for example thread 0 of the virtual core is
currently executing in userspace. However, we do need thread 0
to be responsible for switching the MMU -- a previous version of
this patch that had other threads switching the MMU was found to
be responsible for occasional memory corruption and machine check
interrupts in the guest on POWER7 machines.
To accommodate this, we no longer pass the vcpu pointer to
__kvmppc_vcore_entry, but instead let the assembly code load it from
the PACA. Since the assembly code will need to know the kvm pointer
and the thread ID for threads which don't have a vcpu, we move the
thread ID into the PACA and we add a kvm pointer to the virtual core
structure.
In the case where thread 0 has no vcpu to run, it still calls into
kvmppc_hv_entry in order to do the MMU switch, and then naps until
either its vcpu is ready to run in the guest, or some other thread
needs to exit the guest. In the latter case, thread 0 jumps to the
code that switches the MMU back to the host. This control flow means
that now we switch the MMU before loading any guest vcpu state.
Similarly, on guest exit we now save all the guest vcpu state before
switching the MMU back to the host. This has required substantial
code movement, making the diff rather large.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add Intel RAPL energy counter support (Stephane Eranian)
- Clean up uprobes (Oleg Nesterov)
- Optimize ring-buffer writes (Peter Zijlstra)
Tooling side changes, user visible:
- 'perf diff':
- Add column colouring improvements (Ramkumar Ramachandra)
- 'perf kvm':
- Add guest related improvements, including allowing to specify a
directory with guest specific /proc information (Dongsheng Yang)
- Add shell completion support (Ramkumar Ramachandra)
- Add '-v' option (Dongsheng Yang)
- Support --guestmount (Dongsheng Yang)
- 'perf probe':
- Support showing source code, asking for variables to be collected
at probe time and other 'perf probe' operations that use DWARF
information.
This supports only binaries with debugging information at this
time, detached debuginfo (aka debuginfo packages) support should
come in later patches (Masami Hiramatsu)
- 'perf record':
- Rename --no-delay option to --no-buffering, better reflecting its
purpose and freeing up '--delay' to take the place of
'--initial-delay', so that 'record' and 'stat' are consistent
(Arnaldo Carvalho de Melo)
- Default the -t/--thread option to no inheritance (Adrian Hunter)
- Make per-cpu mmaps the default (Adrian Hunter)
- 'perf report':
- Improve callchain processing performance (Frederic Weisbecker)
- Retain bfd reference to lookup source line numbers, greatly
optimizing, among other use cases, 'perf report -s srcline'
(Adrian Hunter)
- Improve callchain processing performance even more (Namhyung Kim)
- Add a perf.data file header window in the 'perf report' TUI,
associated with the 'i' hotkey, providing a counterpart to the
--header option in the stdio UI (Namhyung Kim)
- 'perf script':
- Add an option in 'perf script' to print the source line number
(Adrian Hunter)
- Add --header/--header-only options to 'script' and 'report', the
default is not tho show the header info, but as this has been the
default for some time, leave a single line explaining how to
obtain that information (Jiri Olsa)
- Add options to show comm, fork, exit and mmap PERF_RECORD_ events
(Namhyung Kim)
- Print callchains and symbols if they exist (David Ahern)
- 'perf timechart'
- Add backtrace support to CPU info
- Print pid along the name
- Add support for CPU topology
- Add new option --highlight'ing threads, be it by name or, if a
numeric value is provided, that run more than given duration
(Stanislav Fomichev)
- 'perf top':
- Make 'perf top -g' refer to callchains, for consistency with
other tools (David Ahern)
- 'perf trace':
- Handle old kernels where the "raw_syscalls" tracepoints were
called plain "syscalls" (David Ahern)
- Remove thread summary coloring, by Pekka Enberg.
- Honour -m option in 'trace', the tool was offering the option to
set the mmap size, but wasn't using it when doing the actual mmap
on the events file descriptors (Jiri Olsa)
- generic:
- Backport libtraceevent plugin support (trace-cmd repository, with
plugins for jbd2, hrtimer, kmem, kvm, mac80211, sched_switch,
function, xen, scsi, cfg80211 (Jiri Olsa)
- Print session information only if --stdio is given (Namhyung Kim)
Tooling side changes, developer visible (plumbing):
- Improve 'perf probe' exit path, release resources (Masami
Hiramatsu)
- Improve libtraceevent plugins exit path, allowing the registering
of an unregister handler to be called at exit time (Namhyung Kim)
- Add an alias to the build test makefile (make -C tools/perf
build-test) (Namhyung Kim)
- Get rid of die() and friends (good riddance!) in libtraceevent
(Namhyung Kim)
- Fix cross build problems related to pkgconfig and CROSS_COMPILE not
being propagated to the feature tests, leading to features being
tested in the host and then being enabled on the target (Mark
Rutland)
- Improve forked workload error reporting by sending the errno in the
signal data queueing integer field, using sigqueue and by doing the
signal setup in the evlist methods, removing open coded equivalents
in various tools (Arnaldo Carvalho de Melo)
- Do more auto exit cleanup chores in the 'evlist' destructor, so
that the tools don't have to all do that sequence (Arnaldo Carvalho
de Melo)
- Pack 'struct perf_session_env' and 'struct trace' (Arnaldo Carvalho
de Melo)
- Add test for building detached source tarballs (Arnaldo Carvalho de
Melo)
- Move some header files (tools/perf/ to tools/include/ to make them
available to other tools/ dwelling codebases (Namhyung Kim)
- Move logic to warn about kptr_restrict'ed kernels to separate
function in 'report' (Arnaldo Carvalho de Melo)
- Move hist browser selection code to separate function (Arnaldo
Carvalho de Melo)
- Move histogram entries collapsing to separate function (Arnaldo
Carvalho de Melo)
- Introduce evlist__for_each() & friends (Arnaldo Carvalho de Melo)
- Automate setup of FEATURE_CHECK_(C|LD)FLAGS-all variables (Jiri
Olsa)
- Move arch setup into seprate Makefile (Jiri Olsa)
- Make libtraceevent install target quieter (Jiri Olsa)
- Make tests/make output more compact (Jiri Olsa)
- Ignore generated files in feature-checks (Chunwei Chen)
- Introduce pevent_filter_strerror() in libtraceevent, similar in
purpose to libc's strerror() function (Namhyung Kim)
- Use perf_data_file methods to write output file in 'record' and
'inject' (Jiri Olsa)
- Use pr_*() functions where applicable in 'report' (Namhyumg Kim)
- Add 'machine' 'addr_location' struct to have full picture (machine,
thread, map, symbol, addr) for a (partially) resolved address,
reducing function signatures (Arnaldo Carvalho de Melo)
- Reduce code duplication in the histogram entry creation/insertion
(Arnaldo Carvalho de Melo)
- Auto allocate annotation histogram data structures (Arnaldo
Carvalho de Melo)
- No need to test against NULL before calling free, also set freed
memory in struct pointers to NULL, to help fixing use after free
bugs (Arnaldo Carvalho de Melo)
- Rename some struct DSO binary_type related members and methods, to
clarify its purpose and need for differentiation (symtab_type, ie
one is about the files .text, CFI, etc, i.e. its binary contents,
and the other is about where the symbol table came from (Arnaldo
Carvalho de Melo)
- Convert to new topic libraries, starting with an API one (sysfs,
debugfs, etc), renaming liblk in the process (Borislav Petkov)
- Get rid of some more panic() like error handling in libtraceevent.
(Namhyung Kim)
- Get rid of panic() like calls in libtraceevent (Namyung Kim)
- Start carving out symbol parsing routines (perf, just moving
routines to topic files in tools/lib/symbol/, tools that want to
use it need to integrate it directly, ie no
tools/lib/symbol/Makefile is provided (Arnaldo Carvalho de Melo)
- Assorted refactoring patches, moving code around and adding utility
evlist methods that will be used in the IPT patchset (Adrian
Hunter)
- Assorted mmap_pages handling fixes (Adrian Hunter)
- Several man pages typo fixes (Dongsheng Yang)
- Get rid of several die() calls in libtraceevent (Namhyung Kim)
- Use basename() in a more robust way, to avoid problems related to
different system library implementations for that function
(Stephane Eranian)
- Remove open coded management of short_name_allocated member (Adrian
Hunter)
- Several cleanups in the "dso" methods, constifying some parameters
and renaming some fields to clarify its purpose (Arnaldo Carvalho
de Melo)
- Add per-feature check flags, fixing libunwind related build
problems on some architectures (Jean Pihet)
- Do not disable source line lookup just because of one failure.
(Adrian Hunter)
- Several 'perf kvm' man page corrections (Dongsheng Yang)
- Correct the message in feature-libnuma checking, swowing the right
devel package names for various distros (Dongsheng Yang)
- Polish 'readn()' function and introduce its counterpart,
'writen()' (Jiri Olsa)
- Start moving timechart state from global variables to a 'perf_tool'
derived 'timechart' struct (Arnaldo Carvalho de Melo)
... and lots of fixes and improvements I forgot to list"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (282 commits)
perf tools: Remove unnecessary callchain cursor state restore on unmatch
perf callchain: Spare double comparison of callchain first entry
perf tools: Do proper comm override error handling
perf symbols: Export elf_section_by_name and reuse
perf probe: Release all dynamically allocated parameters
perf probe: Release allocated probe_trace_event if failed
perf tools: Add 'build-test' make target
tools lib traceevent: Unregister handler when xen plugin is unloaded
tools lib traceevent: Unregister handler when scsi plugin is unloaded
tools lib traceevent: Unregister handler when jbd2 plugin is is unloaded
tools lib traceevent: Unregister handler when cfg80211 plugin is unloaded
tools lib traceevent: Unregister handler when mac80211 plugin is unloaded
tools lib traceevent: Unregister handler when sched_switch plugin is unloaded
tools lib traceevent: Unregister handler when kvm plugin is unloaded
tools lib traceevent: Unregister handler when kmem plugin is unloaded
tools lib traceevent: Unregister handler when hrtimer plugin is unloaded
tools lib traceevent: Unregister handler when function plugin is unloaded
tools lib traceevent: Add pevent_unregister_print_function()
tools lib traceevent: Add pevent_unregister_event_handler()
tools lib traceevent: fix pointer-integer size mismatch
...
Pull core debug changes from Ingo Molnar:
"Currently there are two methods to set the panic_timeout: via
'panic=X' boot commandline option, or via /proc/sys/kernel/panic.
This tree adds a third panic_timeout configuration method:
configuration via Kconfig, via CONFIG_PANIC_TIMEOUT=X - useful to
distros that generally want their kernel defaults to come with the
.config.
CONFIG_PANIC_TIMEOUT defaults to 0, which was the previous default
value of panic_timeout.
Doing that unearthed a few arch trickeries regarding arch-special
panic_timeout values and related complications - hopefully all
resolved to the satisfaction of everyone"
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
powerpc: Clean up panic_timeout usage
MIPS: Remove panic_timeout settings
panic: Make panic_timeout configurable
Race conditions are theoretically possible between the PCI device addition
and removal in the PPC64 PCI error recovery driver and the generic PCI bus
rescan and device removal that can be triggered via sysfs.
To avoid those race conditions make PPC64 PCI error recovery driver use
global PCI rescan-remove locking around PCI device addition and removal.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For one PCI error relevant OPAL event, we possibly have multiple
EEH errors for that. For example, multiple frozen PEs detected on
different PHBs. Unfortunately, we didn't cover the case. The patch
enumarates the return value from eeh_ops::next_error() and change
eeh_handle_special_event() and eeh_ops::next_error() to handle all
existing EEH errors.
As Ben pointed out, we needn't list_for_each_entry_safe() since we
are not deleting any PHB from the hose_list and the EEH serialized
lock should be held while purging EEH events. The patch covers those
suggestions as well.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, if a process starts a transaction and then takes an
exception because the FPU, VMX or VSX unit is unavailable to it,
we end up corrupting any FP/VMX/VSX state that was valid before
the interrupt. For example, if the process starts a transaction
with the FPU available to it but VMX unavailable, and then does
a VMX instruction inside the transaction, the FP state gets
corrupted.
Loading up the desired state generally involves doing a reclaim
and a recheckpoint. To avoid corrupting already-valid state, we have
to be careful not to reload that state from the thread_struct
between the reclaim and the recheckpoint (since the thread_struct
values are stale by now), and we have to reload that state from
the transact_fp/vr arrays after the recheckpoint to get back the
current transactional values saved there by the reclaim.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, when we have a process using the transactional memory
facilities on POWER8 (that is, the processor is in transactional
or suspended state), and the process enters the kernel and the
kernel then uses the floating-point or vector (VMX/Altivec) facility,
we end up corrupting the user-visible FP/VMX/VSX state. This
happens, for example, if a page fault causes a copy-on-write
operation, because the copy_page function will use VMX to do the
copy on POWER8. The test program below demonstrates the bug.
The bug happens because when FP/VMX state for a transactional process
is stored in the thread_struct, we store the checkpointed state in
.fp_state/.vr_state and the transactional (current) state in
.transact_fp/.transact_vr. However, when the kernel wants to use
FP/VMX, it calls enable_kernel_fp() or enable_kernel_altivec(),
which saves the current state in .fp_state/.vr_state. Furthermore,
when we return to the user process we return with FP/VMX/VSX
disabled. The next time the process uses FP/VMX/VSX, we don't know
which set of state (the current register values, .fp_state/.vr_state,
or .transact_fp/.transact_vr) we should be using, since we have no
way to tell if we are still in the same transaction, and if not,
whether the previous transaction succeeded or failed.
Thus it is necessary to strictly adhere to the rule that if FP has
been enabled at any point in a transaction, we must keep FP enabled
for the user process with the current transactional state in the
FP registers, until we detect that it is no longer in a transaction.
Similarly for VMX; once enabled it must stay enabled until the
process is no longer transactional.
In order to keep this rule, we add a new thread_info flag which we
test when returning from the kernel to userspace, called TIF_RESTORE_TM.
This flag indicates that there is FP/VMX/VSX state to be restored
before entering userspace, and when it is set the .tm_orig_msr field
in the thread_struct indicates what state needs to be restored.
The restoration is done by restore_tm_state(). The TIF_RESTORE_TM
bit is set by new giveup_fpu/altivec_maybe_transactional helpers,
which are called from enable_kernel_fp/altivec, giveup_vsx, and
flush_fp/altivec_to_thread instead of giveup_fpu/altivec.
The other thing to be done is to get the transactional FP/VMX/VSX
state from .fp_state/.vr_state when doing reclaim, if that state
has been saved there by giveup_fpu/altivec_maybe_transactional.
Having done this, we set the FP/VMX bit in the thread's MSR after
reclaim to indicate that that part of the state is now valid
(having been reclaimed from the processor's checkpointed state).
Finally, in the signal handling code, we move the clearing of the
transactional state bits in the thread's MSR a bit earlier, before
calling flush_fp_to_thread(), so that we don't unnecessarily set
the TIF_RESTORE_TM bit.
This is the test program:
/* Michael Neuling 4/12/2013
*
* See if the altivec state is leaked out of an aborted transaction due to
* kernel vmx copy loops.
*
* gcc -m64 htm_vmxcopy.c -o htm_vmxcopy
*
*/
/* We don't use all of these, but for reference: */
int main(int argc, char *argv[])
{
long double vecin = 1.3;
long double vecout;
unsigned long pgsize = getpagesize();
int i;
int fd;
int size = pgsize*16;
char tmpfile[] = "/tmp/page_faultXXXXXX";
char buf[pgsize];
char *a;
uint64_t aborted = 0;
fd = mkstemp(tmpfile);
assert(fd >= 0);
memset(buf, 0, pgsize);
for (i = 0; i < size; i += pgsize)
assert(write(fd, buf, pgsize) == pgsize);
unlink(tmpfile);
a = mmap(NULL, size, PROT_READ|PROT_WRITE, MAP_PRIVATE, fd, 0);
assert(a != MAP_FAILED);
asm __volatile__(
"lxvd2x 40,0,%[vecinptr] ; " // set 40 to initial value
TBEGIN
"beq 3f ;"
TSUSPEND
"xxlxor 40,40,40 ; " // set 40 to 0
"std 5, 0(%[map]) ;" // cause kernel vmx copy page
TABORT
TRESUME
TEND
"li %[res], 0 ;"
"b 5f ;"
"3: ;" // Abort handler
"li %[res], 1 ;"
"5: ;"
"stxvd2x 40,0,%[vecoutptr] ; "
: [res]"=r"(aborted)
: [vecinptr]"r"(&vecin),
[vecoutptr]"r"(&vecout),
[map]"r"(a)
: "memory", "r0", "r3", "r4", "r5", "r6", "r7");
if (aborted && (vecin != vecout)){
printf("FAILED: vector state leaked on abort %f != %f\n",
(double)vecin, (double)vecout);
exit(1);
}
munmap(a, size);
close(fd);
printf("PASSED!\n");
return 0;
}
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we set irq_work on a processor and immediately afterward, before the
irq work has a chance to be processed, we change the decrementer value,
we can seriously delay the handling of that irq_work.
Fix it by checking in a few places for pending irq work, first before
changing the decrementer in decrementer_set_next_event() and after
changing it in the same function and in timer_interrupt().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Huge Dickins reported an issue that b5ff4211a8
"powerpc/book3s: Queue up and process delayed MCE events" breaks the
PowerMac G5 boot. This patch fixes it by moving the mce even processing
away from syscall exit, which was wrong to do that in first place, and
using irq work framework to delay processing of mce event.
Reported-by: Hugh Dickins <hughd@google.com
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some devices, for example PCI root port, don't have IOMMU table and
group. We needn't detach them from their IOMMU group. Otherwise, it
potentially incurs kernel crash because of referring NULL IOMMU group
as following backtrace indicates:
.iommu_group_remove_device+0x74/0x1b0
.iommu_bus_notifier+0x94/0xb4
.notifier_call_chain+0x78/0xe8
.__blocking_notifier_call_chain+0x7c/0xbc
.blocking_notifier_call_chain+0x38/0x48
.device_del+0x50/0x234
.pci_remove_bus_device+0x88/0x138
.pci_stop_and_remove_bus_device+0x2c/0x40
.pcibios_remove_pci_devices+0xcc/0xfc
.pcibios_remove_pci_devices+0x3c/0xfc
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When EEH error comes to one specific PCI device before its driver
is loaded, we will apply hotplug to recover the error. During the
plug time, the PCI device will be probed and its driver is loaded.
Then we wrongly calls to the error handlers if the driver supports
EEH explicitly.
The patch intends to fix by introducing flag EEH_DEV_NO_HANDLER and
set it before we remove the PCI device. In turn, we can avoid wrongly
calls the error handlers of the PCI device after its driver loaded.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After reset on the specific PE or PHB, we never configure AER
correctly on PowerNV platform. We needn't care it on pSeries
platform. The patch introduces additional EEH operation eeh_ops::
restore_config() so that we have chance to configure AER correctly
for PowerNV platform.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
The one instance where we add an include for init.h covers off
a case where that file was implicitly getting it from another
header which itself didn't need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc fix from Ben Herrenschmidt:
"Here's one regression fix for 3.13 that I would appreciate if you
could still pull in. It was an "interesting" one to debug, basically
it's an old bug that got somewhat "exposed" by new code breaking the
boot on PA Semi boards (yes, it does appear that some people are still
using these!)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Check return value of instance-to-package OF call
On PA-Semi firmware, the instance-to-package callback doesn't seem
to be implemented. We didn't check for error, however, thus
subsequently passed the -1 value returned into stdout_node to
thins like prom_getprop etc...
Thus caused the firmware to load values around 0 (physical) internally
as node structures. It somewhat "worked" as long as we had a NULL in the
right place (address 8) at the beginning of the kernel, we didn't "see"
the bug. But commit 5c0484e25e
"powerpc: Endian safe trampoline" changed the kernel entry point causing
that old bug to now cause a crash early during boot.
This fixes booting on PA-Semi board by properly checking the return
value from instance-to-package.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Olof Johansson <olof@lixom.net>
---
the setup before the change was
- arch/powerpc/Kconfig had the PPC_CLOCK option, off by default
- depending on the PPC_CLOCK option the arch/powerpc/kernel/clock.c file
was built, which implements the clk.h API but always returns -ENOSYS
unless a platform registers specific callbacks
- the MPC52xx platform selected PPC_CLOCK but did not register any
callbacks, thus all clk.h API calls keep resulting in -ENOSYS errors
(which is OK, all peripheral drivers deal with the situation)
- the MPC512x platform selected PPC_CLOCK and registered specific
callbacks implemented in arch/powerpc/platforms/512x/clock.c, thus
provided real support for the clock API
- no other powerpc platform did select PPC_CLOCK
the situation after the change is
- the MPC512x platform implements the COMMON_CLK interface, and thus the
PPC_CLOCK approach in arch/powerpc/platforms/512x/clock.c has become
obsolete
- the MPC52xx platform still lacks genuine support for the clk.h API
while this is not a change against the previous situation (the error
code returned from COMMON_CLK stubs differs but every call still
results in an error)
- with all references gone, the arch/powerpc/kernel/clock.c wrapper and
the PPC_CLOCK option have become obsolete, as did the clk_interface.h
header file
the switch from PPC_CLOCK to COMMON_CLK is done for all platforms within
the same commit such that multiplatform kernels (the combination of 512x
and 52xx within one executable) keep working
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
On Freescale e6500 cores EPCR[DGTMI] controls whether guest supervisor
state can execute TLB management instructions. If EPCR[DGTMI]=0
tlbwe and tlbilx are allowed to execute normally in the guest state.
A hypervisor may choose to virtualize TLB1 and for this purpose it
may use IPROT to protect the entries for being invalidated by the
guest. However, because tlbwe and tlbilx execution in the guest state
are sharing the same bit, it is not possible to have a scenario where
tlbwe is allowed to be executed in guest state and tlbilx traps. When
guest TLB management instructions are allowed to be executed in guest
state the guest cannot use tlbilx to invalidate TLB1 guest entries.
Linux is using tlbilx in the boot code to invalidate the temporary
entries it creates when initializing the MMU. The patch is replacing
the usage of tlbilx in initialization code with tlbwe with VALID bit
cleared.
Linux is also using tlbilx in other contexts (like huge pages or
indirect entries) but removing the tlbilx from the initialization code
offers the possibility to have scenarios under hypervisor which are
not using huge pages or indirect entries.
Signed-off-by: Diana Craciun <Diana.Craciun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
There are a few things that make the existing hw tablewalk handlers
unsuitable for e6500:
- Indirect entries go in TLB1 (though the resulting direct entries go in
TLB0).
- It has threads, but no "tlbsrx." -- so we need a spinlock and
a normal "tlbsx". Because we need this lock, hardware tablewalk
is mandatory on e6500 unless we want to add spinlock+tlbsx to
the normal bolted TLB miss handler.
- TLB1 has no HES (nor next-victim hint) so we need software round robin
(TODO: integrate this round robin data with hugetlb/KVM)
- The existing tablewalk handlers map half of a page table at a time,
because IBM hardware has a fixed 1MiB indirect page size. e6500
has variable size indirect entries, with a minimum of 2MiB.
So we can't do the half-page indirect mapping, and even if we
could it would be less efficient than mapping the full page.
- Like on e5500, the linear mapping is bolted, so we don't need the
overhead of supporting nested tlb misses.
Note that hardware tablewalk does not work in rev1 of e6500.
We do not expect to support e6500 rev1 in mainline Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Mihai Caraman <mihai.caraman@freescale.com>
Haren Myneni