Remove warning on scan complete with unknown ID, since this
scan could be already cleared in abort flow.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The ssid_bitmap should be unsigned, though it doesn't matter
much as the high bits aren't used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For background and scheduled scan, using the new unified scan API,
support random MAC address scanning.
Unfortunately, the firmware right now doesn't support randomising
itself, so for now do it on the host - we'll change this once the
firmware supports randomising the address for each scan iteration
using the address/mask.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC TLV bit may be on in FWs that support UMAC scan; so check
for UMAC TLV bit first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This API uses second CPU scan commands, and can support multiple
simultaneous scans.
Adding the new API, and adding new mechanisms to deal with up to
8 simultaneous scans instead of the old scan status.
New scan API requires scan configuration for default scan parameters,
adding it in _up flow. Also updating scan configuration after updating
valid scan antennas via debugfs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since it's too complicated for the fw to insert a DS Parameter Set
element in the middle of the frame, it was decided that it should be
done by the host. The fw will only parse the frame and update the
current channel field.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scan reference wasn't released in case of offloaded scan,
causing the refcount to go wrong and prevent the device
from going into d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan condition iterator assumes that an interface is associated if
phy_ctxt is assigned, but this isn't the sutuation in P2P device.
OTOH P2P device is never associated so we can simply ignore it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan. Spin a new function
off of the sched_scan_start op code for reuse. Additionally,
restructure the function a bit for more readability.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reduce basic active dwell time from 30 ms on 2.4 GHz and 20 on 5.2 to
20 on 2.4 and 10 on 5.2.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable fragmented scan that was diabled due to a FW bug.
New fixed FWs use a TLV bit to advertise fragmented scan support.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.
This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).
As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use num of scan channels as advertised by fw TLV.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The low-priority scan feature can be useful, e.g. for OBSS
scans (if those are required by the AP); add back support
for it, restoring the maximum out time to the value it was
for low-priority scan before that was removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use ksize to get scan command size instead of calculating it, to
avoid nasty bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current sched scan channel configuration code
configures all the supported channels for scanning.
However, this can result in SYSASSERT in some cases,
when the configured channel is disabled.
Instead, configure only the channels given in the
req struct, and set the channel_count field appropriately.
While on it, change the code to use channel->hw_value
instead of recalculating the channel number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
tail should be equal to the last valid index, so
decrease it by one.
This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
CMD_SYNC is really 0 which is confusing:
if (cmd.flags & CMD_SYNC) is always false.
Fix this by simply removing its definition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an option to notify mac80211 about sched scan complete from
iwl_mvm_stop_sched_scan(), to enable this notification when the
stop was called from within the driver.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch enables Energy Based Scan (EBS) - intended to detect energy
on 5 GHz band channels. Passive scan on this band takes up to 2.64 sec
assuming 110mSec per-channel * 24 channels. EBS is designed to detect
energy on channels with intensive Wifi activity as well as those where
only beacons are transmitted. EBS completes sampling all channels within
shortest beacon frame transmission time. Total EBS duration is about 100
msec (typical beacon interval).
Detecting Wifi activity on 5 GHz band channels can significantly reduce
scan duration thus saving time and power. EBS failure reported by FW
disables EBS for current connection. It is re-enabled upon new
connection attempt on any WLAN interface.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware doesn't handle properly the fragmented scan.
Stop using it.
While at it change max_out_time and suspend_time units from
usec to TUs as expected by firmware API.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
While the scan_cmd should really be allocated in init (and
we do fail init in case the allocation failed), it doesn't
mean we should lock up the machine if something really bad
happened.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
- passive scan fragment duration = 20ms
- out-of-channel time = 70ms
- suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.
The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.
Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A scheduled scan is a more persistent setting and should take priority
over temporary regular scans. Abort the regular when a sched_scan
request arrives and then request the sched_scan.
The kernel API allows sending a sched_scan without canceling a regular
scan in progress, so this is our way to abstract the FW's limitations.
Make the scan-cancel Rx handler async and flush after invocation to
ensure new scans can't creep in before it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
cfg80211 assumes a scheduled scan is stopped synchronously. Wait for the
FW before returning to caller.
Don't do anything in the async handler in the stop-from-above flow.
There's no need to call the mac80211 sched-scan completion as the
cleanup will be automatic. Make sure the async handler is called before
the next incoming scan changes the scan_status by flushing the async
handlers after all invocations.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
BGN SKU won't scan on 5.2GHz obviously, but the firmware
still expects the driver to reserve space for the the probe
request for the 5.2GHz band.
Fix this by allocating space and leave it empty.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69541
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These inlines are pretty pointless now as they just return a
fixed struct value, remove them - the code even gets shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scheduled scan matchsets were intended to be a list of filters,
with the found BSS having to pass at least one of them to be passed
to the host. When the RSSI attribute was added, however, this was
broken and currently wpa_supplicant adds that attribute in its own
matchset; however, it doesn't intend that to mean that anything
that passes the RSSI filter should be passed to the host, instead
it wants it to mean that everything needs to also have higher RSSI.
This is semantically problematic because we have a list of filters
like [ SSID1, SSID2, SSID3, RSSI ] with no real indication which
one should be OR'ed and which one AND'ed.
To fix this, move the RSSI filter attribute into each matchset. As
we need to stay backward compatible, treat a matchset with only the
RSSI attribute as a "default RSSI filter" for all other matchsets,
but only if there are other matchsets (an RSSI-only matchset by
itself is still desirable.)
To make driver implementation easier, keep a global min_rssi_thold
for the entire request as well. The only affected driver is ath6kl.
I found this when I looked into the code after Raja Mani submitted
a patch fixing the n_match_sets calculation to disregard the RSSI,
but that patch didn't address the semantic issue.
Reported-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some older versions of wpa_supplicant don't necessarily stop
scheduled scan before starting a regular scan, and there's
nothing in the API that requires it either. As a consequence
our driver's behaviour of not allowing scan while scheduled
scan was in progress broke userspace.
However, it is valid to unilaterally stop scheduled scan at
any point in time, so when a regular scan request comes just
abort the scheduled scan and run the regular scan.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take a reference when starting to scan and release it on completion.
Note that if the scan is cancelled/aborted, a completion will still be
sent up.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Notify scan completed if fw_restart flow isn't going to be run.
Otherwise, the scan will stay stack forever and mac80211 will
not be able to remove the interface.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Not doing so will let BT kill our probe requests leading to
failures in scan.
Cc: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
David Spinadel