LPF is short for "low pass filter".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current PLL settings produce a rather unstable picture when
I hook up a VLV to my HP ZR24w display via a VGA cable.
According to VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9, we should
use the the same LPF coefficients for DAC as we do for HDMI and RBR DP.
And indeed that seems to cure the shivers.
v2: Add the name of the relevant document to the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the current GPU frquency is below RPe, and we're asked to increase
it, just go directly to RPe. This should provide better performance
faster than letting the frequency trickle up in response to the up
threshold interrupts.
For now just do it for VLV, since that matches quite closely how VLV
used to operate when the rps delayed timer kept things at RPe always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's little point in increasing the GPU frequency from the delayed
rps work on VLV. Now when the GPU is idle, the GPU frequency actually
keeps dropping gradually until it hits the minimum, whereas previously
it just ping-ponged constantly between RPe and RPe-1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs.
Reading it always returns zero from what I can tell, and eliminating
it doesn't seem to make any difference to the behaviour of the system.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eliminate the weird inverted logic from the rps new_delay comparison.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that even though Punit reports the frequency change to have
been completed, it still reports the old frequency in the status
register for some time.
So rather than polling for Punit to complete the frequency change after
each request, poll before. This gets rid of the spurious "Punit overrode
GPU freq" messages.
This also lets us continue working while Punit is performing the actual
frequency change. As a result, openarena demo088-test1 timedemo average
fps is increased by ~5 fps, and the slowest frame duration is reduced
by ~25%.
The sysfs cur_freq file always reads the current frequency from Punit
anyway, so having rps.cur_delay be slightly off at times doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print both the MHz value and raw register value for rps stuff.
Also kill a somewhat pointless local 'rpe' variable and just use
dev_priv->rps.rpe_delay.
While at it clean up the caps in "GPU" and "Punit" debug messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Report back the user error of attempting to setup a CRTC with an invalid
framebuffer pitch. This is trickier than it should be as on gen4, there
is a restriction that tiled surfaces must have a stride less than 16k -
which is less than the largest supported CRTC size.
v2: Fix the limits for gen3
v3: Move check into intel_framebuffer_init() and fix VLV limits. (vsyrjala)
v4: Use idiomatic '>=' for generation checks
References: https://bugs.freedesktop.org/show_bug.cgi?id=65099
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to apply WaForceL3Serialization:vlv twice.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are legit cases, e.g. when userspace asks for something
impossible. So tune it down to debug output like we do with all other
userspace-triggerable warnings.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66111#c5
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.
v2: Update comment a bit.
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the trend and don't code conditions with platforms but with
features.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/i915_gem.c: In function ‘i915_gem_object_bind_to_gtt’:
drivers/gpu/drm/i915/i915_gem.c:3002:3: warning: format ‘%ld’ expects
argument of type ‘long int’, but argument 5 has type ‘size_t’ [-Wformat]
v2: Use %zu instead of %d. Two char patch, and 100% wrong. (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing the user (nor we) really can do about this, but upsets a nice
quiet boot.
Note that this happens mostly on SDVs where OEMs obviously haven't had
a chance yet to appropriately trim the output list.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65988
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Amend commit message a bit to clarify a question from Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Git commit 90797e6d1e
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.
On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:
[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28
Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).
That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).
Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.
This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.
An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some virtualized environments (e.g. XEN), there is irrelevant ISA bridge in
the system. To work reliably, we should scan trhough all the ISA bridge
devices and check for the first match, instead of only checking the first one.
Signed-off-by: Rui Guo <firemeteor@users.sourceforge.net>
[danvet: Fixup conflict with the num_pch_pll removal. And add
subsystem header to the commit message headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it's the function that destroys the connector, not the
encoder. And we already have intel_dp_encoder_destroy.
This has annoyed me for a long time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Various fixes that make surviving concurrent piglit more possible.
- Buffer object deletion no longer synchronous
- Context/register initialisation updates that have been reported to
solve some stability issues (particularly on some problematic GF119
chips)
- Kernel side support for VP2 video decoding engines
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (44 commits)
drm/nvd0-/disp: handle case where display engine is missing/disabled
drm/gr/nvc0-: merge nvc0/nve0 ucode, and use cpp instead of m4
drm/nouveau/bsp/nv84: initial vp2 engine implementation
drm/nouveau/vp/nv84: initial vp2 engine implementation
drm/nouveau/core: xtensa engine base class implementation
drm/nouveau/vdec: fork vp3 implementations from vp2
drm/nouveau/core: move falcon class to engine/
drm/nouveau/kms: don't fail if there's no dcb table entries
drm/nouveau: remove limit on gart
drm/nouveau/vm: perform a bar flush when flushing vm
drm/nvc0/gr: cleanup register lists, and add nvce/nvcf to switches
drm/nvc8/gr: update initial register/context values
drm/nvc4/gr: update initial register/context values
drm/nvc1/gr: update initial register/context values
drm/nvc3/gr: update initial register/context values
drm/nvc0/gr: update initial register/context values
drm/nvd9/gr: update initial register/context values
drm/nve4/gr: update initial register/context values
drm/nvc0-/gr: bump maximum gpc/tpc limits
drm/nvf0/gr: initial register/context setup
...
Not really "core" per-se. About to merge Ilia's work adding another
similar class for the VP2 xtensa engines, so, seems like a good time to
move all these to engine/.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Most graphics cards nowadays have a multiple of this limit as their vram,
so limiting GART doesn't seem to make much sense.
Signed-off-by: Maarten >Lnkhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Appears to fix the regression from "drm/nvc0/vm: handle bar tlb flushes
internally".
nvidia always seems to do this flush after writing values.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvc0_vm_flush() accesses the pgd list, which will soon be able to race
with vm_unlink() during channel destruction.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These operations can take quite some time, and we really don't want to
have to hold a spinlock for too long.
Now that the lock ordering for vm and the gr/nv84 hw bug workaround has
been reversed, it's possible to use a mutex here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ville Syrjälä