* Move check_dma_crc() to ide-dma.c and add inline version for
CONFIG_BLK_DEV_IDEDMA=n case.
* Rename check_dma_crc() to ide_check_dma_crc().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* siimage.c: use hwif->sata_scr[SATA_{ERROR,STATUS}_OFFSET] instead of
SATA_{ERROR,STATUS}_REG macros.
* Remove no longer needed SATA_*_REG macros.
While at it:
* Remove needless SATA Status register read from sil_sata_reset_poll().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ->nice0 and ->nice2 ide_drive_t fields are always zero so remove them.
* IDE_NICE_0 and IDE_NICE_2 defines from <linux/hdreg.h> are no longer
used by any kernel code so cover them with #ifndef/#endif __KERNEL__.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Un-static create_proc_ide_drives() and call it from ide_device_add_all().
While at it:
* Rename create_proc_ide_drives() to ide_proc_port_register_devices().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out devices setup from ide_acpi_init() to
ide_acpi_port_init_devices().
* Call ide_acpi_port_init_devices() in ide_device_add_all().
While at it:
* Remove no longer needed 'drive' field from struct ide_acpi_drive_link.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->port_init_devs method to ide_hwif_t for a host specific
initialization of devices on a port. Call the new method from
ide_port_init_devices().
* Convert ht6560b, qd65xx and opti621 host drivers to use the new
->port_init_devs method.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use the same bit for IDE_HFLAG_CS5520 and IDE_HFLAG_VDMA host flags
(both are used only by cs5520 host driver currently).
* Add IDE_HFLAG_NO_IO32_BIT host flag and use it instead of ->no_io_32bit
ide_hwif_t field.
* Add IDE_HFLAG_NO_UNMASK_IRQS host flag, then convert dtc2278 and rz1000
host drivers to use it.
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out code for finding ide_hwifs[] slot from ide_register_hw()
to ide_deprecated_find_port().
* Convert bast-ide, ide-cs and delkin_cb host drivers to use ide_device_add()
instead of ide_register_hw() (while at it drop doing "ide_unregister()" loop
which tries to unregister _all_ IDE interfaces if useable ide_hwifs[] slot
cannot be find).
This patch leaves us with only two ide_register_hw() users:
- drivers/macintosh/mediabay.c
- drivers/ide/ide.c
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'init_default' (flag for calling init_hwif_default()) and 'restore'
(flag for calling ide_hwif_restore()) arguments to ide_unregister().
* Update ide_unregister() users to set 'init_default' and 'restore' flags.
* No need to set 'init_default' flag in ide_register_hw() if the setup done
by init_hwif_default() is going to be overridden by ide_init_port_hw().
* No need to set 'init_default' and 'restore' flags in cleanup_module().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also, move xfer_func_t typedef to the ide.h since it is used by two drivers
now (more coming).
Bart:
- use __func__ while at it
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
* 'for-linus' of git://linux-nfs.org/~bfields/linux: (100 commits)
SUNRPC: RPC program information is stored in unsigned integers
SUNRPC: Move exported symbol definitions after function declaration part 2
NLM: tear down RPC clients in nlm_shutdown_hosts
SUNRPC: spin svc_rqst initialization to its own function
nfsd: more careful input validation in nfsctl write methods
lockd: minor log message fix
knfsd: don't bother mapping putrootfh enoent to eperm
rdma: makefile
rdma: ONCRPC RDMA protocol marshalling
rdma: SVCRDMA sendto
rdma: SVCRDMA recvfrom
rdma: SVCRDMA Core Transport Services
rdma: SVCRDMA Transport Module
rdma: SVCRMDA Header File
svc: Add svc_xprt_names service to replace svc_sock_names
knfsd: Support adding transports by writing portlist file
svc: Add svc API that queries for a transport instance
svc: Add /proc/sys/sunrpc/transport files
svc: Add transport hdr size for defer/revisit
svc: Move the xprt independent code to the svc_xprt.c file
...
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (128 commits)
USB: fix codingstyle issues in drivers/usb/core/*.c
USB: fix codingstyle issues in drivers/usb/core/message.c
USB: fix codingstyle issues in drivers/usb/core/hcd-pci.c
USB: fix codingstyle issues in drivers/usb/core/devio.c
USB: fix codingstyle issues in drivers/usb/core/devices.c
USB: fix codingstyle issues in drivers/usb/core/*.h
USB: fix codingstyle issues in include/linux/usb/
USB: fix codingstyle issues in include/linux/usb.h
USB: mark USB drivers as being GPL only
USB: use a real vendor and product id for root hubs
USB: mount options: fix usbfs
USB: Fix usb_serial_driver structure for Kobil cardreader driver.
usb: ehci should use u16 for isochronous intervals
usb: ehci, remove false clear-reset path
USB: Use menuconfig objects
usb: ohci-sm501 driver
usb: dma bounce buffer support
USB: last abuses of intfdata in close for usb-serial drivers
USB: kl5kusb105 don't flush to logically disconnected devices
USB: oti6858: cleanup
...
Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them? What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?
As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware). This is the sort of decision that
should be made in userspace, not in the kernel.
If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.
The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL. The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The execution of ACPI global control methods _GTS and _BFS is
currently tied to the preparation to enter a sleep state and to the
leaving of the sleep state, respectively. However, these functions
are called before disabling the nonboot CPUs and after enabling
them, respectively (in fact, on ACPI 1.0x systems the first of them
ought to be called before suspending devices), while according to the
ACPI specification, _GTS is to be executed right prior to entering
the system sleep state and _BFS is to be executed right after the
platfor firmware has returned control to the OS on wake up.
Move the execution of _GTS and _BFS to the right places.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch (as1008b) converts the PM notifier routines from inline
calls to out-of-line code. It also prevents pm_chain_head from
being created when CONFIG_PM_SLEEP isn't enabled, and EXPORTs the
notifier registration and unregistration routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Add PM_RESTORE_PREPARE and PM_POST_RESTORE notifiers to the PM core, to be used
in analogy with the existing PM_HIBERNATION_PREPARE and PM_POST_HIBERNATION
notifiers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Move the definitions of hibernation ioctls to a separate header file in
include/linux, which can be exported to the user space.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.
Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it. If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state
and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function pci_osc_support_set() traverses every root bridge when
checking for _OSC support for a capability. It quits as soon as it finds a
device/bridge that doesn't support the requested capability. This won't
work for systems that have mixed PCI and PCIe bridges when checking for
PCIe features. I split this function into two -- pci_osc_support_set() and
pcie_osc_support_set(). The latter is used when only PCIe devices should be
traversed.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that all in-tree users are gone, this removes pci_enable_device_bars()
completely.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pci_enable_device_bars() interface isn't well suited to PCI
because you can't actually enable/disable BARs individually on
a device. So for example, if a device has 2 memory BARs 0 and 1,
and one of them (let's say 1) has not been successfully allocated
by the firmware or the kernel, then enabling memory decoding
shouldn't be permitted for the entire device since it will decode
whatever random address is still in that BAR 1.
So a device must be either fully enabled for IO, for Memory, or
for both. Not on a per-BAR basis.
This provides two new functions, pci_enable_device_io() and
pci_enable_device_mem() to replace pci_enable_device_bars(). The
implementation internally builds a BAR mask in order to be able
to use existing arch infrastructure.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current pci_assign_unassigned_resources() code doesn't work properly
on 32 bits platforms with 64 bits resources. The main reason is the use
of unsigned long in various places instead of resource_size_t.
This is a pre-requisite for making powerpc use the generic code instead of
its own half-useful implementation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI error recovery usually involves the PCI adapter being reset.
If the device is using MSI, the reset will cause the MSI state
to be lost; the device driver needs to restore the MSI state.
The pci_restore_msi_state() routine is currently protected
by CONFIG_PM; remove this, and also export the symbol, so
that it can be used in a modle.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vendor_compatible and device_compatible fields in struct pci_dev aren't
used anywhere, and are somewhat pointless. Assuming that these are
historical artifacts, remove them.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch #if 0's the following unused global functions:
- rom.c: pci_map_rom_copy()
- rom.c: pci_remove_rom()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_restore_bars() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (100 commits)
ide: move hwif_register() call out of ide_probe_port()
ide: factor out code for tuning devices from ide_probe_port()
ide: move handling of I/O resources out of ide_probe_port()
ide: make probe_hwif() return an error value
ide: use ide_remove_port_from_hwgroup in init_irq()
ide: prepare init_irq() for using ide_remove_port_from_hwgroup()
ide: factor out code removing port from hwgroup from ide_unregister()
ide: I/O resources are released too early in ide_unregister()
ide: cleanup ide_system_bus_speed()
ide: remove needless zeroing of hwgroup fields from init_irq()
ide: remove unused ide_hwgroup_t fields
ide_platform: remove struct hwif_prop
ide: remove hwif->present manipulations from hwif_init()
ide: move wait_hwif_ready() documentation in the right place
ide: fix handling of busy I/O resources in probe_hwif()
<linux/hdsmart.h> is not used by kernel code
ide: don't include <linux/hdsmart.h>
ide-floppy: cleanup header
ide: update/add my Copyrights
ide: delete filenames/versions from comments
...
This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some boards (like e.g. Tosa) invert the VBUS-detection signal:
it's low when a host is supplying VBUS, and high otherwise.
Allow specifying whether gpio_vbus value is inverted.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bartlomiej Zolnierkiewicz