Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
Aside of the usual boring core properties (compatible, reg, interrupts
and clocks), the bindings use the OF graph bindings to model connections
between the DU output video ports and the on-board and off-board
components.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The THC63LVDM83D is a video LVDS serializer described by an input port,
an output port, and an optional power down GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The ADV7123 is a video DAC described by an input port, an output port,
and an optional power save GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The VGA connector is described by a single input port and an optional
DDC bus.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The quite-recently-added analog-tv-connector bindings say that the
compatible string for composite video connector is
"composite-connector". That string is also used in the omap3-n900.dts
file. However, the connector driver uses "composite-video-connector", so
this has never worked.
While changing the driver's compatible string to "composite-connector"
would be safer, as published DT bindings should not be changed, I'd
rather fix the bindings in this case for two reasons:
* composite-connector is a bit too generic name, as it doesn't even hint
at video.
* it's clear that this has never worked, which means no one has used
those bindings, which should make it safe to change this.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
* Much better HDMI infoframe support for OMAP
* Cirrus Logic CLPS711X framebuffer driver
* DT support for PL11x CLCD driver
* Various small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gXX+
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
In case of using MIPI DSI based I80 interface panel,
the relevant registers should be set.
So this patch adds relevant DT bindings.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Configuration sets for Exynos 4210 and 4x12 SoC were already defined in
Exynos HDMI and Mixed drivers, but they lacked proper linking to device
tree 'compatible' values. This patch fixes this issue adding support for
following compatible values: samsung,exynos4210-mixer,
samsung,exynos4212-mixer and samsung,exynos4210-hdmi. It also corrects
access to sclk_mixer clock, which is available only on Exynos 4210.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The code has a variable to change the polarity of the PWM backlight control but
it was not being initialized. This patch adds a devicetree entry to set the
variable if required.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch adds basic DT bindings for the PL11x CLCD cells
and make their fbdev driver use them.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch removes fimd and fb codes for s5pc100 SoC.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch removes fimd codes for s5p6440 and s5p6450 SoCs.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add OF document for Cirrus Logic CLPS711X framebuffer driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull drm updates from Dave Airlie:
"This is the main drm merge window pull request, changes all over the
place, mostly normal levels of churn.
Highlights:
Core drm:
More cleanups, fix race on connector/encoder naming, docs updates,
object locking rework in prep for atomic modeset
i915:
mipi DSI support, valleyview power fixes, cursor size fixes,
execlist refactoring, vblank improvements, userptr support, OOM
handling improvements
radeon:
GPUVM tuning and large page size support, gart fixes, deep color
HDMI support, HDMI audio cleanups
nouveau:
- displayport rework should fix lots of issues
- initial gk20a support
- gk110b support
- gk208 fixes
exynos:
probe order fixes, HDMI changes, IPP consolidation
msm:
debugfs updates, misc fixes
ast:
ast2400 support, sync with UMS driver
tegra:
cleanups, hdmi + hw cursor for Tegra 124.
panel:
fixes existing panels add some new ones.
ipuv3:
moved from staging to drivers/gpu"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (761 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
Exynos drm hdmi driver used to get dummy hdmiphy clock to
control the PMU bit for hdmiphy. This bit needs to be set
before setting any resolution to hdmi hardware. This was
handled using dummy hdmiphy clock which is removed here.
PMU is already defined as system controller for exynos
SoCs. Hdmi driver is modified to control the phy enable bit
inside PMU using regmap interfaces.
Devicetree binding document for hdmi is also updated.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Enable support for hdmi for exynos5420 hdmiphy. Add
compatible string in the of_match table. Also added
hdmiphy configuration values for exynos5420.
Signed-off-by: Rahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Certain bridge chips use a GPIO to indicate the cable status instead
of the I_DP_HPD pin. This adds an optional device-tree property,
"samsung,hpd-gpio", to the exynos-dp controller which indicates that
the specified GPIO should be used for hotplug detection.
The GPIO is then set up as an edge-triggered interrupt where the
rising edge indicates hotplug-in and the falling edge indicates hotplug-out.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add documentation for defining HDMI lane functions and polarities.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
The patch adds DT bindings for Exynos DSI Master. DSIM follows rules
for DSI bus host bindings [1].
Properties describes its resources: memory, interrupt, clocks,
phy, regulators, frequencies of clocks and video interfaces.
[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch adds bindings required to add support
for parallel output.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch moves the exynos_drm_display implementation from fimd into
the dp driver. This will allow for tighter integration of the dp driver
into the exynos drm driver.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The i2c client was previously being passed into the hdmi driver via a
dedicated i2c driver, and then a global variable. This patch removes all
of that and just uses the device tree to get the i2c_client. This patch
also properly references the client so we don't lose it before we're
done with it.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
[seanpaul changed to phandle lookup instead of using of node name]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add DT binding documentation for Sony acx565akm panel
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Add DT binding documentation for DVI Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Add DT binding documentation for Analog TV Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Add device tree bindings for OMAP Display Subsystem for the following
SoCs: OMAP2, OMAP3, OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
This patch replaces custom lcd_power() callback with
regulator API over LCD class.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TWR-P1025 Overview
-----------------
512Mbyte DDR3 (on board DDR)
64MB Nor Flash
eTSEC1: Connected to RGMII PHY AR8035
eTSEC3: Connected to RGMII PHY AR8035
Two USB2.0 Type A
One microSD Card slot
One mini-PCIe slot
One mini-USB TypeB dual UART
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Mostly bug fixes and clean up. There is a new driver, which is actually
moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree support
in the pwm-backlight driver. Backlights can now additionally be powered
using a regulator and enabled using a GPIO in addition to just the PWM
input.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CB+z
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
Nothing particularly stands out in this pull request. The biggest part of the
changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix potential
dead lock" which hopefully fixes the fb locking issues reported by multiple
persons.
There are also a few commits that have changes to arch/arm/mach-at91 and
arch/avr32, which have been acked by the maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=59+j
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Nothing particularly stands out in this pull request. The biggest
part of the changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix
potential dead lock" which hopefully fixes the fb locking issues
reported by multiple persons.
There are also a few commits that have changes to arch/arm/mach-at91
and arch/avr32, which have been acked by the maintainers"
* tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (143 commits)
fb: reorder the lock sequence to fix potential dead lock
fbdev: shmobile-lcdcfb: Convert to clk_prepare/unprepare
fbdev: shmobile-hdmi: Convert to clk_prepare/unprepare
omapdss: Add new panel driver for Topolly td028ttec1 LCD.
video: exynos_mipi_dsi: Unlock the mutex before returning
video: da8xx-fb: remove unwanted define
video: Remove unnecessary semicolons
simplefb: use write-combined remapping
simplefb: fix unmapping fb during destruction
OMAPDSS: connector-dvi: fix releasing i2c_adapter
OMAPDSS: DSI: fix perf measuring ifdefs
framebuffer: Use fb_<level>
framebuffer: Add fb_<level> convenience logging macros
efifb: prevent null-deref when iterating dmi_list
fbdev: fix error return code in metronomefb_probe()
video: xilinxfb: Fix for "Use standard variable name convention"
OMAPDSS: Fix de_level in videomode_to_omap_video_timings()
video: xilinxfb: Simplify error path
video: xilinxfb: Use devm_kzalloc instead of kzalloc
video: xilinxfb: Use standard variable name convention
...
LP8555 is one of the LP855x family devices.
This device needs pre_init_device() and post_init_device() driver
structure. It's same as LP8557, so the device configuration code is
shared with LP8557. Backlight outputs are generated from dual DC-DC boost
converters. It's configurable EPROM settings which are defined in the
platform data.
Driver documentation and device tree bindings are updated.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie