IIO_EV_TYPE_THRESH in rising direction describes an event where the
threshold is crossed in rising direction, positive or negative values
being possible. This is not the case here.
Since the threshold is no signed value and only the magnitude is compared,
IIO_EV_TYPE_MAG is what describes the behaviour of these devices, see the
sysfs-bus-iio ABI Documentation.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In bmc150_accel_unregister_triggers() triggers should be unregistered in
reverse order of registration. Trigger registration starts with number 0,
counting up. In consequence, trigger number needs to be count down here.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Reviewed-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sNVc
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third round of new IIO drivers, cleanups and functionality for the 4.2 cycle.
Given Linus announced a 4.8rc coming up, hopefully time for one more
lot of IIO patches this cycle. Some of these are actually
improvements / fixes for patches earlier in the cycle.
New device support
* st_accel driver - support devices with 8 bit channels.
Cleanup
* A general cleanup of the iio tools under /tools/ from Hartmut.
I'm more than a little embarassed by how bad some of these were! Are well,
much more refined and less bug prone now.
These cover lots of stuff like unhandled error returns, memory leaks as
well as general refactoring to tidy the code up.
* iio_simple_dummy - fix memory leaks in the init functions, drop some
pointless error returns from functions that never generate errors and
make the module parameter explicitly unsigned.
* More buffer handling reworks from Lars-Peter, this time targetting hardware
buffers (a little used corner that looks likely to get more use in the near
future). Specifically:
- Always compute the masklength as inkernel buffer users may need it.
- Add a means of labeling which buffer modes a given buffer implementation
supports.
- In the case of hardware buffers, require strict scan matching rather than
matching to a superset. Currently the demux is bypassed by these drivers
(this may well not change for efficiency reasons) so allowing a superset
of channels to be selected would otherwise lead to more data than requested
confusing userspace.
Driver funcationality improvments
* mmc35240 - adds a compensation to the raw values as borrowed form Memsic's
own input driver.
* mma8452
- event support
- event debouncing
- high pass filter configuration
- triggers
* vf610 - allow conversion mode to be adjusted
Fixlets
* mmc35240
- Off by one error that by coincidence had no real effect.
- i2c_device_name should be lowercase.
- Lack of null terminator at end of attributes array.
- Avoid computing the fractional part of the magnetic field by moving
the scaling into userspace where floating point is available to simplify
the maths.
- Use a smaller sleep before assuming the measurement is done. This is
safe and improves the possible polling rate.
- Fix sensitivity on z-axis - datasheet disagrees with Memsic's releasedd
code and the value used in the code seems to be correct.
* stk3310 - make a local variable signed to ensure error handling works.
* twl4030
- fix calculation of the temperature sense current - bug unlikely
to have ever been noticed as the difference is small.
- Fix errors in descriptions.
This adds support for the LIS331DL sensor version. This is
a simple 8bit-only accelerometer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some sensors like the LIS331DL only support 8bit data by a single
register per axis. These utilize the MSB byte. Make it possible
to register these apropriately.
A oneliner change is needed in the ST sensors core to handle 8bit
reads as this is the first supported 8bit sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Implement interrupt driven trigger for data ready.
This allows more efficient access to the sample data.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow the cutoff frequency of the high pass filter to be configured.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow the debouce counter for transient events to be configured
using the sysfs attribute events/in_accel_thresh_rising_period
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The event is triggered when the highpass filtered absolute acceleration
exceeds the threshold.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uX2k
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new driver, functionality and cleanups for IIO in the 4.2 cycle.
Core functionality
* i and q modifiers from quadrature channels.
* IIO_CHAN_INFO_OVERSAMPLING_RATIO added.
* High pass filter attributes added to mirror the existing low pass filter
ones.
Core cleanups
* Make IIO tools building more cross compiler friendly.
* Substantial rework of the function __iio_update_buffers to greatly simplify
a hideously evolved function.
New drivers and support
* ACPI0008 ambient light sensor driver. This one has been around a long time to
will be good to finally get it into mainline.
* Berlin SOC ADC support.
* BMC150 magnetometer. The accelerometer in the same package has been supported
for quite some time, so good to have this half as well.
* m62332 DAC driver
* MEMSIC MMC35420 magnetometer.
* ROHM BH1710 and similar ambient light sensors.
* Sensortek STK3310 light sensor.
* Sensortek STK8312 accelerometer.
* Sensortek STK8BA50 accelerometer.
* ti-adc128s052 gains support form the adc122s021 2 channel ADC.
Driver cleanups and functionality.
* Allow various drivers to compile with !GPIOLIB if COMPILE_TEST enabled.
* bmc150 - decouple trigger from buffer to allow other triggers to be used.
* bmg160 - decouple trigger from buffer to allow other triggers to be used.
Fix a trivial unused field.
* Constify a load of platform_device_id structures.
* inv_mpu6050 - device tree bindings.
* hid-sensors - fix a memory leak during probe if certain errors occur.
* ltr501 - illuminance channel derived (in an non obvious fashion) from the
intensity channels.
* ltr501 - fix a boundary check on the proximity threshold.
* mlx90614 - drop a pointless return.
* mma8452 - Debugfs register access and fix a bug that had no effect (by
coincidence)
* ti_am335x_adc - add device tree bindings for sample-delay, open-delay and
averaging. The ideal settings for these tend to be board design specific.
Minimal implementation of an IIO driver for the Sensortek
STK8BA50 3-axis accelerometer. Datasheet:
http://szgsensor.com/uploads/soft/141229/STK8BA50%D2%E5%BC%CE.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Sensortek
STK8312 3-axis accelerometer. Datasheet:
http://www.syi-group.com/uploadpic/data/201361817562681623.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the interrupt pins are not available, we should still be able to use
the buffer with an external trigger. However, we won't be able to use
the hardware fifo since we have no means of signalling when the
watermark is reached.
I also added a comment to indicate that the timestamps in
bmc150_accel_data are only used for hardware fifo, since initially I was
confused about duplication with pf->timestamp.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reviewed-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Many of the hardware configuration registers may only be modified while the
device is inactive.
Currently the probe code first activates the device and then modifies the
registers (eg to set the scale). This doesn't actually work but is not
noticed since the scale used is the default value.
While at it also issue a hardware reset command at probe time.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
'channels' is allocated via kmemdup and it is never freed in the
subsequent error paths.
Use 'indio_dev->channels' directly instead, so that we avoid such
memory leak problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PiG+
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.1a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
The usual mixed bag of fixes for IIO in the 4.1 cycle.
Second version of this pull request as a small fix to a fix turned
up before Greg pulled it for a cc10001 patch near the top of the tree.
One core fix
* Set updated for a iio kfifo was incorrectly set to false during a failed
update, resulting in atttempts to repeat the failed operation appearing
to succeed.
This time I've decided to list the driver fixes in alphabetical order rather
than 'randomly'.
* axp288_adc - a recent change added a check for valid info masks when
reading channels from consumer drivers.
* bmp280 - temperature compensation was failing to read the tfine value, hence
causing a temperature of 0 to always be returned and incorrect presure
measurements.
* cc10001 - Fix channel number mapping when some channels are reserved for
remote CPUs. Fix an issue with the use of the power-up/power-down register
(basically wrong polarity). Fix an issue due to the missinterpretting the
return value from regulator_get_voltage. Add a delay before the start bit
as recommended for the hardware to avoid data corruption.
* hid pressure - fix channel spec of modfiied, but no modifier (which makes no
sense!)
* hid proximity - fix channel spec of modified, but no modifier (which makes
no sense!). Fix a memory leak in the probe function.
* mcp320x - occasional incorrect readings on dma using spi busses due to
cacheline corruption. Fixed by forcing ___cacheline_aligned for the buffers.
* mma9551 - buffer overrun fix (miss specified maximum length of buffers)
* mma9553 - endian fix on status message. Add an enable element for activity
channel. Input checking for activity period to avoid rather unpredictable
results.
* spmi-vadc - fix an overflow in the output value normalization seen on some
boards.
* st-snesors - oops due to use of a mutex that is not yet initialized during
probe.
* xilinx adc - Some wrong register addresses, a wrong address for vccaux
channel, incorrect scale on VREFP and incorrect sign on VREFN.
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wyz7
-----END PGP SIGNATURE-----
Merge tag 'iio-for-v4.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, functionality and cleanups for the 4.2 cycle
New drivers / device support
* st sensors driver, lsm303dlh magnetometer support.
* ltr501 - support ltr301 and ltr559 chips.
New functionality
* IIO_CHAN_INFO_CALIBEMISSIVITY for thermopile sensors.
* kxcjk1013 - make driver operational with external trigger.
* Add iio targets to the tools Makefile.
Cleanups
* st sensors - more helpful error message if device id wrong or irq request
fails, explicitly make the Block Data Update optional rather
than relying on writes to address 0 not doing anything, make interrupt
support optional (Not always wired, and not all devices actually have
an interrupt line.)
* kxcjk-1013 white space additions for readability, add the KXCJ9000 ACPI
id as seen in the wild.
* sx9500 - GPIO reset support, refactor the GPIO interrupt code, add power
management, optimize power usage by powering down when possible, rename
the gpio interrupt pin to be more useful, trivial return path simplification,
trivial formatting fixes.
* isl29018 - move towards ABI compliance with a view to moving this driver
out of staging, add some brackets to ensure code works as expected. Note
there is no actual bug as the condition being tested is always true
(with current devices).
* ltr501 - add regmap support to get caching etc for later patches,
fix a parameter sanity check that always fails (bug introduced
earlier in this series), ACPI enumeration support,
interrupt rate control support, interrupt support in general and
integration time control support, code alignment cleanups.
* mma9553 - a number of little cleanups following a review from Hartmut
after I'd already applied the original driver patch.
* tmp006 - prefix some defines with TMP006 for consistency.
* tsl4531 - cleanup some wrong prefixes, presumably from copy and paste.
* mlx90614 - check for errors in read values, add power management,
add emissivity setting, add device tree binding documentation,
fix a duplicate const warning.
* ti_am335x_adc - refactor the DT parsing into a separate function.
Some extra blank lines between if checks don't hurt and improve
readability.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This id has been seen in the DSDT of the Teclast X98 Air 3G tablet based
on Intel Bay Trail.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial value of gpio bitnum is set to -1, but
the variable is declared as unsigned.
Use a positive invalid value for initial gpio
bitnum.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add mma9553_ prefix to all local functions/declarations.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use GENMASK instead of BIT or direct value to
define a mask.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use "GPIO" instead of "gpio" and "ACPI" instead of "acpi".
Includes a couple of small style fixes in comments
(missing full stop, whitespace, paranthesis).
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use return 0 instead of return ret to mark
clearly the success return path.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Suggested-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When configuring gpio, we need to read initial values for activity and
step count. This function may fail due to i2c read errors.
Check the error code returned by mma9553_read_activity_stepcnt
and return the appropriate error in gpio config function.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When setting the activity period, the value introduced by
the user in sysfs is not checked for validity.
Add a boundary check so that only allowed values are
reported as successfully written to device.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add an enable channel for activity, so it can also
be polled independently of events or other channels.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reported-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The mma9551 functions that read/write word arrays from the
device have a limit for the buffer size given by the device
specifications.
Check that the requested buffer length is within required limits
when transferring word arrays. This will prevent buffer overrun
in the mma9551_read/write_*_words functions and also in the
mma9551_transfer call when writing into the MBOX response/request
structure.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor code for simplicity and clarity.
This also fixes an endianness issue with the original code.
When reading multiple registers, the received buffer of
16-bytes words is little endian (status, step count). On
big endian machines, casting them to u32 would result in
reversed order in the buffer (step count, status) leading
to incorrect values for step count and activity.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In SPI mode the transfer buffer is locked with a mutex. However this
mutex is only initilized after the probe, but some transfer needs to
be done in the probe.
To fix this bug we move the mutex initialization at the beginning of
the device probe.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
In its present state, the driver mandates that its buffer only be
triggered by one of the device's own triggers (data ready or any
motion). This is not always desirable, for example because the
interrupt pins may not be wired in.
Patch the driver to be able to accept using an external trigger, such as
one based on hrtimer. When using such a trigger, we need to ensure that
the device is powered on when the buffer is started. We do that by
setting setup_ops for the buffer.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only advertise hardware fifo support if the I2C bus supports full
I2C or smbus I2C block data reads since it is mandatory to read the
full frame in one read (otherwise the rest of the frame is discarded).
The hardware fifo is enabled only when triggers are not active because:
(a) when using the any-motion trigger the user expects to see samples
based on ROC events, but the fifo stores samples based on the sample
frequency
(b) the data-ready trigger is waking the CPU for for every sample, so
using the hardware fifo does not have any benefit
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the LIS3LV02 accelerometer found in the
ST Microelectronics Nomadik board series.
Cc: devicetree@vger.kernel.org
Cc: Denis CIOCCA <denis.ciocca@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a separate structure for triggers and add the infrastructure to
support an arbitrary number of triggers. Each trigger is associated
with an interrupt and has an enabled/disabled state.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since both triggers and events can share an interrupt, add a data
structure that tracks the users of an interrupt so that it enables or
disables it only for the first users and respectively last user.
This will allows us to easily add more events or triggers.
The patch also adds an interrupt enabled counter, so that we can
easily know if we need to put the device in normal mode when the
resume callback is issued.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently driver reports device bandwidth list as available
sampling frequency. But sampling frequency is actually twice
the device bandwidth. This patch fixes this issue.
Signed-off-by: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The return value of gpiod_to_irq should be checked before giving
it to devm_request_threaded_irq in order to not pass an error
code in case it fails.
Signed-off-by: Roberta Dobrescu <roberta.dobrescu@gmail.com>
Reviewed-by: Vlad Dogaru <vlad.dogaru@intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the in-kernel push interface is used we may have a different masks
on the device buffer and the kernel buffer and in this case the device
should generate data for the reunion of the buffers, which is
available at indio_dev->active_scan_mask.
Compiled tested only except for bmc150-accel which was tested at
runtime with the hardware.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previous of this patch the check was only done if we enabled the event
and it was already enabled. We can do the same if the event is
disabled and we want to disable it.
The patch also adds the same check on the trigger code.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Martin Kepplinger