Commit 0b30704304 ("IB/mad: Return error response for unsupported
MADs") does not handle directed-route MADs properly -- it fails to set
the 'D' bit in the response MAD status field. This is a problem for
SmInfo MADs when the receiver does not have an SM running.
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Hibernation regression fix, since 3.2.
Calculate the number of required free pages based on non-high memory
pages only, because that is where the buffers will come from.
Commit 081a9d043c introduced a new buffer
page allocation logic during hibernation, in order to improve the
performance. The amount of pages allocated was calculated based on total
amount of pages available, although only non-high memory pages are
usable for this purpose. This caused hibernation code to attempt to over
allocate pages on platforms that have high memory, which led to hangs.
Signed-off-by: Bojan Smojver <bojan@rexursive.com>
Signed-off-by: Rafael J. Wysocki <rjw@suse.de>
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The field is used to pass the UVC request data length, but can also be
used to signal an error when setting it to a negative value. Switch from
unsigned int to __s32.
Reported-by: Fernandez Gonzalo <gfernandez@copreci.es>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed following compile time error.
arch/arm/mach-exynos/common.c: In function 'exynos5_init_irq':
arch/arm/mach-exynos/common.c:539:2: error: implicit declaration of function 'of_irq_init'
arch/arm/mach-exynos/common.c:539:14: error: 'exynos4_dt_irq_match' undeclared (first use in this function)
arch/arm/mach-exynos/common.c:539:14: note: each undeclared identifier is reported only once for each function it appears in
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Should be EXYNOS4_IRQ_DWMCI instead of IRQ_DWMCI,
and use DEFINE_RES_{MEM,IRQ}.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
warning: (CPU_S3C2440 && CPU_S3C2442) selects S3C2410_PM which has unmet direct dependencies (ARCH_S3C24XX && CPU_S3C2410)
warning: (CPU_S3C2440 && CPU_S3C2442) selects S3C2410_PM which has unmet direct dependencies (ARCH_S3C24XX && CPU_S3C2410)
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed to fix mini2440_defconfig after the platform
files have been moved around.
arm-none-linux-gnueabi-ld: no machine record defined
arm-none-linux-gnueabi-ld: no machine record defined
arm-none-linux-gnueabi-ld: no machine record defined
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes the following build failures:
drivers/staging/octeon/ethernet.c: In function 'cvm_oct_cleanup_module':
drivers/staging/octeon/ethernet.c:799:2: error: implicit declaration of function 'free_irq'
drivers/staging/octeon/ethernet-rx.c: In function 'cvm_oct_no_more_work':
drivers/staging/octeon/ethernet-rx.c:119:3: error: implicit declaration of function 'enable_irq'
drivers/staging/octeon/ethernet-rx.c: In function 'cvm_oct_do_interrupt':
drivers/staging/octeon/ethernet-rx.c:136:2: error: implicit declaration of function 'disable_irq_nosync'
drivers/staging/octeon/ethernet-rx.c: In function 'cvm_oct_rx_initialize':
drivers/staging/octeon/ethernet-rx.c:532:2: error: implicit declaration of function 'request_irq'
drivers/staging/octeon/ethernet-tx.c: In function 'cvm_oct_tx_initialize':
drivers/staging/octeon/ethernet-tx.c:712:2: error: implicit declaration of function 'request_irq'
drivers/staging/octeon/ethernet-tx.c: In function 'cvm_oct_tx_shutdown':
drivers/staging/octeon/ethernet-tx.c:723:2: error: implicit declaration of function 'free_irq'
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZCACHE is a boolean in the Kconfig. When selected, it
should require that CRYPTO be builtin (=y).
Currently, ZCACHE=y and CRYPTO=m is a valid configuration
when it should not be.
This patch changes the zcache Kconfig to enforce this
dependency.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead now use ioremap. This is needed for 3.4 since this change
emerged in mainline during one of the previous rc cycles.
These solves the following compilation breaks:
drivers/staging/tidspbridge/core/tiomap3430.c:
In function ‘bridge_brd_start’:
drivers/staging/tidspbridge/core/tiomap3430.c:425:4:
error: implicit declaration of function ‘OMAP2_L4_IO_ADDRESS’
drivers/staging/tidspbridge/core/wdt.c: In function ‘dsp_wdt_init’:
drivers/staging/tidspbridge/core/wdt.c:56:2:
error: implicit declaration of function ‘OMAP2_L4_IO_ADDRESS’
For control registers a new function needs to be defined so we
can get rid of a layer violation, but that approach must be queued
for the next merge window.
As seen in:
http://www.arm.linux.org.uk/developer/build/
platform: omap4430-sdp build: uImage
config: randconfig version: 3.4.0-rc3
start time: Apr 20 2012 01:07
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cifs_show_options uses the wrong conversion specifier for uid, gid,
rsize & wsize. Correct this to %u to match it to the variable type
'unsigned integer'.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Show backupuid/backupgid in /proc/mounts for cifs shares mounted with
the backupuid/backupgid feature.
Also consolidate the two separate checks for
pvolume_info->backupuid_specified into a single if condition in
cifs_setup_cifs_sb().
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Command complete event for HCI_OP_USER_PASSKEY_NEG_REPLY would result
in calling handler function also for HCI_OP_LE_SET_SCAN_PARAM. This
could result in undefined behaviour.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
This patch instructs DLM to prevent an "in place" conversion, where the
lock just stays on the granted queue, and instead forces the conversion to
the back of the convert queue. This is done on upward conversions only.
This is useful in cases where, for example, a lock is frequently needed in
PR on one node, but another node needs it temporarily in EX to update it.
This may happen, for example, when the rindex is being updated by gfs2_grow.
The gfs2_grow needs to have the lock in EX, but the other nodes need to
re-read it to retrieve the updates. The glock is already granted in PR on
the non-growing nodes, so this prevents them from continually re-granting
the lock in PR, and forces the EX from gfs2_grow to go through.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Add description for 'reg' field.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The error handling code w.r.t. idr usage looks inconsistent.
In the case of drm_mode_object_get() and drm_ctxbitmap_next() the error
handling is also incomplete.
Unify the code to follow the same pattern always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EFI doesn't typically make use of the legacy VGA ROM, but it may still be
configured to pass that through to a given video device. This may lead to
an inaccurate choice of default video device. Add support to efifb to pick
out the correct active video device.
v2: fix if->ifdef
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: hpa@zytor.com
Cc: matt.fleming@intel.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
IORESOURCE_ROM_SHADOW is not necessarily an indication that the hardware
is the primary device. Add support for using the vgaarb functions and
fall back if nothing's set them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: mingo@redhat.com
Acked-by: hpa@zytor.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
vga-switcheroo currently changes the default VGA device by fiddling with
the IORESOURCE_ROM_SHADOW flag on the device. This isn't strictly accurate,
since there's no guarantee that switching also changes the ROM decoding.
Switch over to using the vgaarb functions for this.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The default VGA device is a somewhat fluid concept on platforms with
multiple GPUs. Add support for setting it so switching code can update
things appropriately, and make sure that the sysfs code returns the right
device if it's changed.
v2: Updated to fix builds when __ARCH_HAS_VGA_DEFAULT_DEVICE is false.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: benh@kernel.crashing.org
Cc: airlied@redhat.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add support for rs6xx
- add support for DCE4/5
- fixup 6xx/7xx
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds register definitions for HDMI/DP audio on
DCE2/3/4/5 hardware.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Improve handling of bpc (bits per color) in radeon.
In most cases we want 8 except for HDMI, DP, LVDS, and eDP.
v2: handle DP better.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Horst Hartmann <horst.hartmann@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f793.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: set fake_rtable's dst to NULL to avoid kernel Oops
when bridge is deleted before tap/vif device's delete, kernel may
encounter an oops because of NULL reference to fake_rtable's dst.
Set fake_rtable's dst to NULL before sending packets out can solve
this problem.
v4 reformat, change br_drop_fake_rtable(skb) to {}
v3 enrich commit header
v2 introducing new flag DST_FAKE_RTABLE to dst_entry struct.
[ Use "do { } while (0)" for nop br_drop_fake_rtable()
implementation -DaveM ]
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Peter Huang <peter.huangpeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are two low-risk bug fixes for ext4, fixing a compile warning
and a potential deadlock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Ygid
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"These are two low-risk bug fixes for ext4, fixing a compile warning
and a potential deadlock."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
super.c: unused variable warning without CONFIG_QUOTA
jbd2: use GFP_NOFS for blkdev_issue_flush
Pull Hexagon fixes from Richard Kuo:
"It's mostly compile fixes and the Hexagon portion of a CPU hotplug
patch set."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
hexagon: add missing cpu.h include
hexagon/CPU hotplug: Add missing call to notify_cpu_starting()
hexagon: use renamed tick_nohz_idle_* functions
Hexagon: misc compile warning/error cleanup due to missing headers
Pull build system failure fix from Michal Marek:
"This fixes build failure with newer gcc that adds some internal
symbols that end in "__mod_*_device_table", but are not actually the
tables themselves."
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Fix modpost failures in fedora 17
sb info is only checked with quota support.
fs/ext4/super.c: In function ‘parse_options’:
fs/ext4/super.c:1600:23: warning: unused variable ‘sbi’ [-Wunused-variable]
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
flush request is issued in transaction commit code path, so looks using
GFP_KERNEL to allocate memory for flush request bio falls into the classic
deadlock issue. I saw btrfs and dm get it right, but ext4, xfs and md are
using GFP.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: stable@vger.kernel.org
2 are tagged for -stable, one being for a fairly serious bug
that can corrupt metadata and make it hard to recovery an array.
The other is for a more recent regression since 3.3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=8UG6
-----END PGP SIGNATURE-----
Merge tag 'md-3.4-fixes' of git://neil.brown.name/md
Pull a few more md bug fixes from NeilBrown:
"2 are tagged for -stable, one being for a fairly serious bug that can
corrupt metadata and make it hard to recovery an array. The other is
for a more recent regression since 3.3"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md: fix possible corruption of array metadata on shutdown.
md: don't call ->add_disk unless there is good reason.
DM RAID: Use safe version of rdev_for_each
This includes one short patch fixing the behavior of
the QUECVT flag, which the gfs2 folks are waiting on.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KDNZ
-----END PGP SIGNATURE-----
Merge tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm fixes from David Teigland:
"This includes one short patch fixing the behavior of the QUECVT flag,
which the gfs2 folks are waiting on."
* tag 'dlm-fixes-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
dlm: fix QUECVT when convert queue is empty
Mel reports a BUG_ON(slot == NULL) in radix_tree_tag_set() on s390
3.0.13: called from __set_page_dirty_nobuffers() when page_remove_rmap()
tries to transfer dirty flag from s390 storage key to struct page and
radix_tree.
That would be because of reclaim's shrink_page_list() calling
add_to_swap() on this page at the same time: first PageSwapCache is set
(causing page_mapping(page) to appear as &swapper_space), then
page->private set, then tree_lock taken, then page inserted into
radix_tree - so there's an interval before taking the lock when the
radix_tree slot is empty.
We could fix this by moving __add_to_swap_cache()'s spin_lock_irq up
before the SetPageSwapCache. But a better fix is simply to do what's
five years overdue: Ken Chen introduced __set_page_dirty_no_writeback()
(if !PageDirty TestSetPageDirty) for tmpfs to skip all the radix_tree
overhead, and swap is just the same - it ignores the radix_tree tag, and
does not participate in dirty page accounting, so should be using
__set_page_dirty_no_writeback() too.
s390 testing now confirms that this does indeed fix the problem.
Reported-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ken Chen <kenchen@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide the proper override macros for x32 siginfo_t. The combination
of a special type here and an overall alignment constraint actually
ends up with all the types being properly aligned, but the hack is
needed to keep the substructures inside siginfo_t from adding padding.
Note: use __attribute__((aligned())) since __aligned() is not exported
to user space.
[ v2: fix stray semicolon ]
Reported-by: H.J. Lu <hjl.rools@gmail.com>
Cc: Bruce J. Beare <bruce.j.beare@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/CAMe9rOqF6Kh6-NK7oP0Fpzkd4SBAWU%2BG53hwBbSD4iA2UzyxuA@mail.gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
commit c744a65c1e
md: don't set md arrays to readonly on shutdown.
removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.
If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.
So only call __md_stop_writes() if the array has actually been
activated.
This patch is needed for any stable kernel which has had the above
commit applied.
Cc: stable@vger.kernel.org
Reported-by: Christoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Jack Morgenstein