Currently the devices that have already stripped IEEE 802.11
header from the AMSDU SKB can not use ieee80211_amsdu_to_8023s
routine. This patch enhances ieee80211_amsdu_to_8023s() API by
changing mandatory removing of IEEE 802.11 header from AMSDU
to optional.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These definitions need to be exposed now that we can set the peer link
states via NL80211_ATTR_STA_PLINK_STATE. They were already being
(opaquely) reported by NL80211_STA_INFO_PLINK_STATE.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to advertise interface combinations in nl80211.
This allows the driver to indicate what the combinations are
that it supports. "Combinations" of just a single interface are
implicit, as previously. Note that cfg80211 will enforce that
the restrictions are met, but not for all drivers yet (once all
drivers are updated, we can remove the flag and enforce for all).
When no combinations are actually supported, an empty list will
be exported so that userspace can know if the kernel exported
this info or not (although it isn't clear to me what tools using
the info should do if the kernel didn't export it).
Since some interface types are purely virtual/software and don't
fit the restrictions, those are exposed in a new list of pure SW
types, not subject to restrictions. This mainly exists to handle
AP-VLAN and monitor interfaces in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sched_scan_stopped was called by the driver, mac80211 calls
cfg80211, which in turn was calling mac80211 back with a flag
"driver_initiated". This flag was used so that mac80211 would do the
necessary cleanup but would not call the driver. This was enough to
prevent the bounce back between the driver and mac80211, but not
between mac80211 and cfg80211.
To fix this, we now do the cleanup in mac80211 before calling
cfg80211. To help with locking issues, the workqueue was moved from
cfg80211 to mac80211.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple virtual AP interfaces can currently try
to use different beacon intervals, but that just
leads to problems since it won't actually be done
that way by drivers. Return an error in this case
to make sure it won't be done wrong.
Also, ignore attempts to change the DTIM period
or beacon interval during the lifetime of the BSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce NL80211_ATTR_SCHED_SCAN_INTERVAL as a required attribute for
NL80211_CMD_START_SCHED_SCAN. This value informs the driver at which
intervals the scheduled scan cycles should be executed.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement new functionality for scheduled scan offload. With this feature we
can scan automatically at certain intervals.
The idea is that the hardware can perform scan automatically and filter on
desired results without waking up the host unnecessarily.
Add NL80211_CMD_START_SCHED_SCAN and NL80211_CMD_STOP_SCHED_SCAN
commands to the nl80211 interface. When results are available they are
reported by NL80211_CMD_SCHED_SCAN_RESULTS events. The userspace is
informed when the scheduled scan has stopped with a
NL80211_CMD_SCHED_SCAN_STOPPED event, which can be triggered either by
the driver or by a call to NL80211_CMD_STOP_SCHED_SCAN.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new configuration option to support AMPE from userspace.
Prior to this series we only supported authentication in userspace: an
authentication daemon would authenticate peer candidates in userspace
and hand them over to the kernel. From that point the mesh stack would
take over and establish a peer link (Mesh Peering Management).
These patches introduce support for Authenticated Mesh Peering Exchange
in userspace. The userspace daemon implements the AMPE protocol and on
successfull completion create mesh peers and install encryption keys.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is based on (but now quite far from) the
original work from Luis and Eliad. Add support
for configuring WoWLAN triggers, and getting
the configuration out again. Changes from the
original patchset are too numerous to list,
but one important change needs highlighting:
the suspend() callback is passed NULL for the
trigger configuration if userspace has not
configured WoWLAN at all.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only user of WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS was removed
and consequently, this flag can be removed, too. In addition, a single
capability flag was not enough to indicate this capability clearly since
the device behavior may be different based on which operating mode is
being used.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add station connected time in debugfs. This will be helpful to get a
measure of stability of the connection and for debugging stress issues
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Notify userspace when a beacon/presp is received from a suitable mesh
peer candidate for whom no sta information exists. Userspace can then
decide to create a sta info for the candidate. If userspace is not
ready to authenticate the peer right away, it can create the sta info
with the authenticated flag unset and set it later.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During mesh setup, use NL80211_MESH_SETUP_USERSPACE_AUTH flag to create
a secure mesh and route management frames to userspace.
Also, NL80211_CMD_GET_WIPHY now returns a flag NL80211_SUPPORT_MESH_AUTH
if the wiphy's mesh implementation supports routing of mesh auth frames
to userspace. This is useful for forward compatibility between old
kernels and new userspace tools.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To NL80211_MESH_SETUP_IE. This reflects our ability to insert any ie
into a mesh beacon, not simply path selection ies.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows user-space monitoring of BSS parameters for the associated
station. This is useful for debugging and verifying that the paramaters
are as expected.
[Exactly the same as before but bundled into a single message]
Signed-off-by: Paul Stewart <pstew@chromium.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Indicate an NL80211_CMD_DEL_STATION event when a station entry in
mac80211 is deleted to match with the NL80211_CMD_NEW_STATION event
that is used when the entry was added. This is needed, e.g., to allow
user space to remove a peer from RSN IBSS Authenticator state machine
to avoid re-authentication and re-keying delays when the peer is not
reachable anymore.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix many of each of these warnings:
Warning(include/net/cfg80211.h:519): No description found for parameter 'rxrate'
Warning(include/net/mac80211.h:1163): bad line:
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also fix a typo in the STATION_INFO_TX_BITRATE description
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I made the patch to add mesh join/leave I
didn't pay attention to docs because it was a
proof of concept, and then when we actually did
merge it I forgot -- add docs now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100)
can only TX from a subset of RX antennas, so use separate availability masks
for RX and TX.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Userspace will now be allowed to toggle between the default path
selection algorithm (HWMP, implemented in the kernel), and a vendor
specific alternative. Also in the same patch, allow userspace to add
information elements to mesh beacons. This is accordance with the
Extensible Path Selection Framework specified in version 7.0 of the
802.11s draft.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh parameters can be to setup a mesh or to configure it.
This patch renames the ambiguous name mesh_params to mesh_config
in preparation for mesh_setup.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new notification to indicate that a received, unprotected
Deauthentication or Disassociation frame was dropped due to
management frame protection being in use. This notification is
needed to allow user space (e.g., wpa_supplicant) to implement
SA Query procedure to recover from association state mismatch
between an AP and STA.
This is needed to avoid getting stuck in non-working state when MFP
(IEEE 802.11w) is used and a protected Deauthentication or
Disassociation frame is dropped for any reason. After that, the
station would silently discard any unprotected Deauthentication or
Disassociation frame that could be indicating that the AP does not
have association for the STA (when the Reason Code would be 6 or 7).
IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the upcoming hardware offload implementation,
some devices will have a different maximum duration
for the remain-on-channel command. Advertise the
maximum duration in mac80211, and make mac80211 set
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.
Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.
The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v3: always apply available antenna mask (for "all" antennas case).
v2: reject antenna configurations which don't match the available antennas
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch with the same title was for mac80211 ops, accidentally.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow setting of TX and RX antennas configuration via nl80211.
The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.
Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.
Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.
802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.
Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.
While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:
1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).
2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).
3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WIPHY_FLAG_IBSS_RSN is BIT(7) as is WIPHY_FLAG_CONTROL_PORT_PROTOCOL. Change
to BIT(8).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers may need to adjust their filters according
to frame registrations, so notify them about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using these, user space can calculate a relative channel utilization
with arbitrary intervals by regularly taking snapshots of the survey
results.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some stats for /proc/net/wireless (and wext in general) are not
being set. This patch addresses a few of those with values easily
obtained from mac80211 core.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need for the WDS peer address
to not be const, so make it const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar