Current bnx2x implementation controls the number of VFs only by
standard sysfs support, and will reject setting the number of VFs
when the PF is not loaded.
As a result, there is no need to schedule a delayed work to enable
SR-IOV when PF is loaded, as the number of VFs at that point
must be 0.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running ethtool on VF interfaces, returning values should indicate
that the interface does not support self-test or register dump.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3fb43eb ("bnx2x: Change to D3hot only on removal") nvram
is accessible whenever the driver is loaded - Thus it is possible to
test it during self-test even if the interface is down
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.
Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Local symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b9871bcfd2
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the already existing pm_cap variable in struct pci_dev for
determining the power management offset. This saves the driver from
having to keep track of an extra variable.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization bnx2x allocates significant amounts of memory
(for rx data, rx SGEs, TPA pool) using atomic allocations.
I received a report where bnx2x failed to allocate SGEs and it had
to fall back to TPA-less operation.
Let's use GFP_KERNEL allocations during initialization, which runs
in process context. Add gfp_t parameters to functions that are used
both in initialization and in the receive path.
Use an unlikely branch in bnx2x_frag_alloc() to avoid atomic allocation
by netdev_alloc_frag(). The branch is taken several thousands of times
during initialization, but then never more. Note that fp->rx_frag_size
is never greater than PAGE_SIZE, so __get_free_page() can be used here.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of VF RSS feature doorbell block was configured not to use dpm, but
a small part of configuration was left out, preventing the driver from sending
tx messages to the device. This patch adds the missing configuration.
Reported-by: Eric Dumazet <eric.dumazet@gmil.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c0a77ec74f 'bnx2x: Add missing braces in
bnx2x:bnx2x_link_initialize' identified indentation problem, but resolved it
by adding braces instead of fixing the indentation. The braces now prevents a
config_init call in some cases, though it should be called regardless of that
condition. This patch removes the braces and fix the confusing indentation
that caused this mess.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Dave Jones <davej@redhat.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 60cad4e67b
"bnx2x: VF RSS support - VF side" fails to compile w/o
CONFIG_BNX2X_SRIOV option.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
The indentation here implies that the intent was for this to be a multiline if.
Introduced a few years ago in commit ec146a6f01 ("bnx2x: Modify XGXS functions")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch capabilities are added to the Vf driver to request
multiple queues over the VF PF channel, and the logic for requesting
rss configuration for said queues.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilong Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Receive Side Scaling for queues of
Virtual Functions on the PF side. This includes support for the
requests for multiple queues from VF drivers, configuration of the
HW for multiple queues per VF, and support for rss configuration
of said queues.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PF gathers statistics for the VF, when the VF is about to unload
we must synchronize the release of its statistics buffer with the PF, so that
no DMA operation will be made to that address after the buffer release.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to incorrect VF/PF conditions, when unloading a VF it will not release
part of the memory it has previously allocated.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check on return code of bnx2x_vfop_config_vlan0() would lead to error
handling flow as the return value indicating an existing pending ramrod would
be erroneously considered as an error.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver will fail to allocate all queues, it will shrink the number of
queues and move the storage queue to its correct place (i.e., the last
queue among the newly supported number).
When changing the pointers of the new location of the FCoE queue, we need
to pay special attention to the aggregations pointer - that memory is allocated
during probe and released upon driver removal. Current implementation has 2
pointers pointing to the same chunk of allocated memory, meaning upon removal
there will be two kfree() of the same chunk while the other won't be released.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Solve issue where no stats were being collected for VF devices due to missing
configuration in the stats' atomic synchronization mechanism.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/trans.c
include/linux/inetdevice.h
The inetdevice.h conflict involves moving the IPV4_DEVCONF values
into a UAPI header, overlapping additions of some new entries.
The iwlwifi conflict is a context overlap.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible HW configurations in which PFs will have SR-IOV capability
but will have Max VFs set to 0 - this happens when there are Multi-Function
devices where the VFs are allocated to only some of the PFs.
DMAE is configured to support VFs only if the configuring PF has supported VFs.
In case the first PF to be loaded will be one without supported VFs, it will
not configure DMAE to the VF-supporting mode. When VFs of other PFs will be
loaded later on, they will not be able to communicate with their PF.
This changes the requirement for configuring DMAE for VF-supporting mode;
If the device has SR-IOV capabilities there must be some PF that has
max supported VFs > 0, thus it will configure the DMAE for supporting VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SR-IOV can be activated dynamically and iproute2 can be called
asynchronously, the various callbacks need a robust sanity check before
attempting to access the SR-IOV database and members since there are numerous
states in which it can find the driver (e.g., PF is down, sriov was not enabled
yet, VF is down, etc.).
In many of the states the callback result will be null pointer dereference.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, VFs might erroneously try to access the shared memory (which
only PFs are capabale of accessing), causing benign attentions to appear.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When publishing information via getfeatcfg(), bnx2x driver didn't consider
remote errors (e.g., switch that doesn't support DCBX) when setting the
error flags.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After notification that DCBX configuration has ended arrived to the driver,
the driver configured the FW/HW in sleepless context.
As a result, it was possible to reach a race (mostly with CNIC registration)
in which the configuration will return a timeout, failing to set the DCBX
results correctly.
This patch moves the configuration following the DCBX end into the slowpath
RTNL task (i.e., sleepless context protected by the RTNL lock), allowing the
configuration to cope with such races.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3deb816 "bnx2x: Add a periodic task for link PHY events"
link state changes can be detected not only via the attention flow but also
from the periodic task.
If the link state will change in such a manner (i.e., via the periodic task),
dropless flow-control will not be configured.
This patch remedies the issue, adding the missing configuration to all required
flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There might be a crash as during shutdown flow CNIC might try
to access resources already freed by bnx2x.
Change bnx2x_close() into dev_close() in __bnx2x_remove (shutdown flow)
to guarantee CNIC is notified of the device's change of status.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTE write access error might occur in MF_ALLOWED mode when IOMMU
is active. The patch adds rmmod HSI indicating to MFW to stop
running queries which might trigger this failure.
Signed-off-by: Barak Witkowsky <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS can be enabled as a result of DCB negotiation, then
fairness must be recalculated after each negotiation.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add locking to protect different statistics flows from
running simultaneously.
This in order to serialize statistics requests sent to FW,
otherwise two outstanding queries may cause FW assert.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New routine has been added to avoid duplication of code to wait for
pending PCI transactions to complete. This makes use of that routine.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On very rare occasions, repeated load/unload stress test in the presence of
our storage driver (bnx2i/bnx2fc) causes a kernel panic in bnx2x code
(NULL pointer dereference). Stack traces indicate the issue happens during MAC
configuration; thorough code review showed that indeed several races exist
in which one thread can iterate over the list of configured MACs while another
deletes entries from the same list.
This patch adds a varient on the single-writer/Multiple-reader lock mechanism -
It utilizes an already exsiting bottom-half lock, using it so that Whenever
a writer is unable to continue due to the existence of another writer/reader,
it pends its request for future deliverance.
The writer / last readers will check for the existence of such requests and
perform them instead of the original initiator.
This prevents the writer from having to sleep while waiting for the lock
to be accessible, which might cause deadlocks given the locks already
held by the writer.
Another result of this patch is that setting of Rx Mode is now made in
sleepable context - Setting of Rx Mode is made under a bottom-half lock, which
was always nontrivial for the bnx2x driver, as the HW/FW configuration requires
wait for completions.
Since sleep was impossible (due to the sleepless-context), various mechanisms
were utilized to prevent the calling thread from sleep, but the truth was that
when the caller thread (i.e, the one calling ndo_set_rx_mode()) returned, the
Rx mode was still not set in HW/FW.
bnx2x_set_rx_mode() will now overtly schedule for the Rx changes to be
configured by the sp_rtnl_task which hold the RTNL lock and is sleepable
context.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit c957d09ffd
"bnx2x: Remove sparse and coccinelle warnings"
driver provided wrong partial csum for HW in tunneing
scenarios.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Pravin Shelar <pshelar@nicira.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ndo_ll_poll to ndo_busy_poll.
Rename sk_mark_ll to sk_mark_napi_id.
Rename skb_mark_ll to skb_mark_napi_id.
Correct all useres of these functions.
Update comments and defines in include/net/busy_poll.h
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the file and correct all the places where it is included.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x did not set dump->version in its .get_dump_flag() method.
Let's set it to BNX2X_DUMP_VERSION. It's not a particularly nice
number (0x50acff01 currently), but at least it's something
deterministic.
dump->flag should report the value previously set using ethtool -W.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x interprets the dump flag as an index of a register preset.
It is important to validate the index to avoid out of bounds
memory accesses.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to initialize the dump data with zeros.
data is allocated with vzalloc, so it's already zero-filled.
More importantly, the memset is harmful, because dump->len (the length
requested by userspace) can be bigger than the allocated buffer (whose
size is determined by asking the driver's .get_dump_flag method).
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch solves several sparse issues as well as an unneeded semicolon
found via coccinelle.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes an issue caused by submit 78c3bcc5d1
`bnx2x: Improve PF behaviour toward VF', which made the bnx2x driver fail
compilation when PCI_IOV is not set.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't claim 20G is supported if the speed is unsupported by the phys
(reflected by various ethtools and ndos).
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wait 100ms for FLR to complete in parallel over all VFs instead of serializing
the waits (which can amount to several seconds with 64 VFs).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If iproute2 VF callbacks are invoked before PF is loaded,
abort gracefully.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in bnx2x_init_dev().
Also remove redundant PM Cap find code, because pci core
has been saved the pci device pm cap value.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check next packet availability by validating that HW has finished CQE
placement. This saves latency of another dma transaction performed to update
SB indexes.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds ndo_ll_poll method and locking for FPs between LL and the napi.
When receiving a packet we use skb_mark_ll to record the napi it came from.
Add each napi to the napi_hash right after netif_napi_add().
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.
Commit 057cf65 "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.
This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PCIe supports PM capabilities, bnx2x will always claim eeprom is accessible
as PCI_D0 is zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes a few changes that change the driver's flow without truly
changing anything in its functionality - use usleep_range for short sleeps
instead of msleep and initialize Tx consumer during initialization for better
information during errors.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch revises many bnx2x prints - mainly fixing print typos and
adding some new debug prints (mostly for parity issues).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces several small changes to the driver, none which actually
change any flow:
1. Removes prototypes of unexisting functions and unused defines.
2. Fixes alignment and spacing issues.
3. Changes numeric usage into constants.
4. Remove unnecessary parenthesis.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch correct various typos, fix comments conventions and
adds/removes a few comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unnecessary blank lines and adds a few where such are needed
(between variable declarations and code)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x_select_queue() was using __skb_tx_hash() to select the
transmit queue, totally ignoring XPS settings, while XPS can help
performance quite significantly, so change the bnx2x_select_queue()
to use __dev_pick_tx() instead which will use XPS if configured.
Based on patches from Ying Cai and Havard Skinnemoen
Reported-by: govindarajulu.v <govindarajulu90@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Ying Cai <ycai@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the PCI power management scheme of the bnx2x driver to be similar
to those of most network drivers - the driver will now changes the power state
into D3hot whenever the driver will be removed, instead of whenever an
interface is unloaded.
This change enables the driver to access its eeprom via ethtool callbacks
even when interfaces are unloaded (such access requires the function to be
in D0active).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the PCI shutdown callback to support un-orderly shutdown, i.e.,
shutdowns in which the remove callback will not be called.
Due to the lack of this functionality, when an un-orderly shutdown occurred,
it was possible for wake-on-lan to remain disabled.
This is now fixed as the callback introduces the correct place in which
`system_state' can be queried and wake-on-lan be configured accordingly.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0eb43b4bb0
"bnx2x, bnx2fc: Use per port max exchange resources" has changed the number
of available FCoE exchanges, even in scenarios when some of the functions has
no FCoE support; This needlessly degraded the available resources.
Remedy this by calculating the maximal number of functions that may actually
utilize said connection.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PF should ack the firmware when receiving unknown messages through the VF's
mailbox. This prevents the VF mailbox from being stuck in case of a VF sending
a message unknown to the PF (e.g. VF with more advanced version).
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the print of the PCI gen3 link speed (8GHz), as well as correcting
the same print for 57712 boards (the print erroneously showed a 2.5GHz speed).
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hypervisor/Supervisor should set the VF's MAC prior to its load;
Using a randomly generated MAC as a default is a bad practice.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
In Multi-function mode, all functions should be able to utilize said function;
There's no reason why only the link owner should be able to do so.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCIe advanced error recovery, the secondary bus reset will cause FW
to reset; This will cause the shared memory between it and the driver to be
invalidated.
During the driver's recovery flow, the driver should not make any assumption
on the validity of that memory and instead re-initialize it.
This also removes a redundant re-initialization of a previously
initialized mutex.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the previous unload flow, probed devices will reset the chip
in order to clean the remains of the UNDI driver.
As a result, it's possible for the FW to toggle the link.
This toggling can prove fatal, as long periods without link can cause the
filesystem mount to fail as the storage protocol timeouts. This has been
observed against particular switches with long link re-establishment time.
This patch informs FW during the reset period that the link should not
be toggled - the FW will keep it alive until some interface will load and claim
the link as its own.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize ethtool's callback `get_priv_flags' - shed more light on the
feasibility of devices as storage interfaces.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 91226790bb
`bnx2x: use FW 7.8.17', the bnx2x driver no longer requests the FW to perform
IP checksums for IPv4 packets.
This behaviour needs to be revised for 57710/57711 chips -
when using GSO, if the driver will not set the IP checksum flag then packets
will be transmitted by the chip without a valid IP checksum, resulting in
a drop of all such packets on the receiver-side.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_set_features() forces a driver reload if GRO setting is changed.
A reload makes the ethernet port unresponsive for about 5 seconds.
This is not needed in the common case LRO is enabled, as LRO
(TPA_ENABLE_FLAG) has precedence over GRO (GRO_ENABLE_FLAG)
Tested:
Verified that "ethtool -K eth0 gro {on|off}" doesn't blackout
the NIC anymore
Google-Bug-Id: 8440442
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
bnx2x driver allocates searcher T2 tables, but it releases that memory
during unload only released if the cnic is loaded.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bnx2x driver reads the port configuration - mask irrelevant bits.
Without this change, the unintended bits may cause the driver to needlessly
toggle the link, as a comparison in the link flap avoidance flow will show
that the old link did not advertise the same capabilities and thus cannot
be retained.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d2d2d87dfd
("bnx2x: allow nvram test to run when device is down").
Since it makes access to the device in D3 state possible.
More work is required to make sure device is not set to D3
during ifdown. Until this is done the nvram-test should simply
exit if device is down like it did before.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware supports a maximum of 4K FCoE exchanges. In 4-port devices,
or when working in multi-function mode, this resource needs to be distributed
between the various possible FCoE functions.
This information needs to be calculated by bnx2x and propagated into bnx2fc
via cnic. bnx2fc can then use this value to calculate corresponding xid
resources instead of using global constants.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In scenarios in which a previous driver was removed without proper cleanup
(e.g., kdump), it is possible for the chip to generate an interrupt without
any apparent reason once interrupts are requested.
Due to an erroneous initialization of resources, some of the bnx2x structs
which are required for interrupt handling are initialized only after an
interface's interrupt is requested from the OS.
As a result, once such a spurious interrupt occurs, it will cause a NULL
pointer dereference - the driver will access those structs in its interrupt
handling routine.
This patch change the interrupt request scheme so that bnx2x would only
request interrupts from the kernel after it has finished initializing
all the inner structs required for interrupt handling.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of PCIe Advanced Error Reporting flow, if a fatal PCI error occurs,
the AER driver will cause bnx2x's PCI-core to reset. The driver's PCI error
handlers will in turn restore the PCI configuration space values by calling
`pci_restore_state'.
However, as bnx2x does not save the PCI configuration after restoration,
An additional fatal PCI error will leave the function in an unstable state
until reboot, as the registers in the PCI configuration space will contain
reset values.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exists an `allocation race' between the CNIC and bnx2x drivers,
in which both drivers allocate the same t2 memory while disregarding a possible
previous allocation.
Additionally, due to the current order of memory releases, some of the
ILT memory in the driver is not released correctly when unloading the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improved support for adding/removing vf mac addresses.
This includes the case where HyperVisor forced the address (sampled from
bulletin board), and the case where it did not in which the VF can
configure its own mac address.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when link is configured to auto-negotiate the flow control,
disabling RX/TX pause via ethtool doesn't work.
This fixes the behaviour, advertising asymmetric pause in case either one
is exclusively enabled.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a more robust error handling flow in case of incorrect
behaviour by the FW when passing on GRO aggregations.
Although this should never happen (i.e., this is merely a theoretical fix),
if the bnx2x driver was to receive a GRO from FW with protocol other than
IPv4/IPv6, the driver would falsely claim to have performed partial
checksum and set various incorrect fields in the skb header.
Current behaviour of the bnx2x driver (i.e., print an error) is insufficient.
This patch remedies this by simply preventing the false claims.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in printk and comments within various drivers.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a. Common tree of `dir` structures.
b. Multi-port devices structures.
CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
introduce a procedure to read in u32 granularity.
CC: Francious Romieu <romieu@fz.zoreil.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes 2 issues regarding bnx2x's status blocks:
1. ethtool -c caused corruption of status blocks in FW RAM.
2. when using multi-CoS, the configuration of the timeout values of
status blocks is incorrect, harming the coalescing of interrupts
for such CoSs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When loading after UNDI (e.g., Boot from SAN) the UNDI does not
gracefully yield its resources; The bnx2x driver handles that release
itself.
During the manipulation required to release those resources, it's possible
for the UNDI to try and write to memory regions which are no longer accessible,
causing the PCI bus to prevent further writes from the chip.
This would in turn cause DMAE timeouts later on in the driver, as the driver
will be unable to use the chip's DMA engines.
This patch prevents the chip from actually writing through the PCI bus
in said scenario, thus allowing the release without the unfortunate by-product.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cnic module is responsible for initializing various bnx2x structs
via callbacks provided by the bnx2x module.
One such struct is the queue object for the FCoE queue.
If a device is working in AFEX mode and its configuration allows FCoE yet
the cnic module is not loaded, it's very likely a null pointer dereference
will occur, as the bnx2x will erroneously access the FCoE's queue object.
Prevent said access until cnic properly registers itself.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check KR2 recovery time at the beginning of the work-around function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mutex initialization by allocation of the mailbox it protects.
introduced in commit 1d6f3cd89 'bnx2x: Prevent VF race'
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/ipip.h
The changes made to ipip.h in 'net' were already included
in 'net-next' before that header was moved to another location.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make few alignments, comment fixes and debug messages.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add full support for "ethtool -m" command.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mail box containing the Vf-Pf messages is susceptible
to a race - it's possible for 2 flows to try and write commands,
causing one to override the other's message.
Use a mutex to synchronize the access, preventing said race.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Outer vlan removal in VF queues was made according to the VF's
multi-function mode (which is never set).
Instead, the PF's multi-function mode should be used to determine
if outer vlan removal is needed.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a VF performs load/unload its statistics become corrupt -
we now zero the statistics structures upon a VF device load.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ARI forwarding flag is missing from the PCI bridge, remove SR-IOV
support instead of failing the probe process.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7fa6f34 "AER revised" erroneously inserted an error-flow
in which a semaphore is released even though the attempt to take it
has failed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
57712/578xx devices during handling of encapsulated TSO can
properly increase ip id for only one ip header.
The patch selects inner header to be increased.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ariel Elior <ariele@broadcom.com>
CC: Maciej Zenczykowski <maze@google.com>
CC: Jesse Gross <jesse@nicira.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revised bnx2x implementation of PCI Express Advanced Error Recovery -
stop and free driver resources according to the AER flow (instead of the
currently implemented `hope-for-the-best' release approach), and do not make
any assumptions on the HW state after slot reset.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UPDATE_QSTAT function introduced on February 15, 2012
in commit 1355b704b9 "bnx2x: consistent statistics after
internal driver reload" incorrectly fails to handle overflow
during addition of the lower 32-bit field of a stat.
This bug is present since 3.4-rc1 and should thus be considered
a candidate for stable 3.4+ releases.
Google-Bug-Id: 8374428
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Mintz Yuval <yuvalmin@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch drives FW to perform RSS for GRE traffic,
based on inner headers.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch utilizes FW offload capabilities for
encapsulation protocols.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hardware initialization fails in bnx2x_nic_load() after adding
napi objects, they would not be deleted. A subsequent attempt to unload
the bnx2x module detects a corruption in the napi list.
Add the missing napi deletion to the error path.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Support sysfs interface for getting the maximal number of virtual functions
of a given physical function.
2. Support sysfs interface for getting and setting the current number of
virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.
This patch prevents said message.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In latest boards, the CHIP_METAL register contains an incorrect
revision value, so the correct one needs to be obtained in a
different manner.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual functions don't have access to HW registers, therefore most ethtool ops
are forbidden to them. Instead of checking in each op whether the device being
driven is a virtual function or a physical function, this patch creates a
separate ethtool ops struct for virtual functions and uses it to initialize
the ethtool ops of the driver in case it is driving a virtual function device.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior