Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add hardware blinking support to the pca9633 driver.
NOTE: Hardware blinking violates the leds infrastructure
driver interface since the hardware only supports
blinking all LEDs with the same delay_on/delay_off
rates. That is, only the LEDs that are set to blink
will actually blink but all LEDs that are set to blink
will blink in identical fashion. The delay_on/delay_off
values of the last LED that is set to blink will be used
for all of the blinking LEDs. If the hardware doesn't
support the requested blinking pattern, a default of
500ms on and off will be used.
Hardware blinking is disabled by default but can be enabled
by setting the 'blink_type' member in the platform_data
struct to 'PCA9633_HW_BLINK' or by adding the 'nxp,hw-blink'
property to the DTS.
(fengguang.wu@intel.com: Removes unneeded semicolon.)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP8501 can drive up to 9 channels like LP5523.
LEDs can be controlled directly via the I2C and programmable engines are
supported.
LP55xx common driver
LP8501 is one of LP55xx family device, so LP55xx common code are used.
Chip specific data is defined in the structure, 'lp55xx_device_config'.
Differences between LP8501 and LP5523
Different register layout for LED output control and others.
LP8501 specific feature for separate output power selection.
LP8501 doesn't support external clock detection.
Different programming engine data.
LP8501 specific feature - output power selection
Output channels are selected by power selection - Vout or Vdd.
Separate power for VDD1-6 and VDD7-9 are available.
It is configurable in the platform data.
To support this feature, LP55xx DT structure and header are changed.
Device tree binding is updated as well.
LED pattern data
Example pattern data is updated in the driver documentation.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Similar to tca6507, we can just parse the standard LED
properties for pca9633.
Tested on a pca9632, which is compatible with pca9633.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the led class code to use the
correct field.
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is superseded by the generic pwm-renesas-tpu driver used with
leds-pwm.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
drivers/leds/leds-mc13783.c: In function 'mc13xxx_led_probe':
drivers/leds/leds-mc13783.c:195:2: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Convert drivers/leds/led-class to use dev_pm_ops for power management and
remove Legacy PM ops hooks. With this change, led class registers
suspend/resume callbacks via class->pm (dev_pm_ops) instead of Legacy
class->suspend/resume. When __device_suspend() runs call-backs, it will
find class->pm ops for the led class.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch rewrite driver code to be ready to add support for
MC13892 LEDs and probe from devicetree.
(cooloney@gmail.com: fix one coding style issue when apply this patch)
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Philippe Retornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Static checkers complain that, although this is declared as an
unsigned long, we can only use the lower 32 bits. For anything
higher, we hit bugs widening then bitwise negate or wrapping bugs
doing the left shift.
From looking at the context, this is not a problem because we only
use 16 bits. I've changed some types to make it more clear.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core)
we can rely on device core for handling pinctrl, so remove
devm_pinctrl_get_select_default() from the driver.
Reported-by: Stephen Warren <warren@wwwdotorg.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The LP55xx DT structure is applicable to the LP5562 device.
The driver and documentation are updated.
Compatible property of the DT
: LP5521 and LP5223 were manufactured by National Semiconductor.
LP5562 is a new device from Texas Instruments.
Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Currently, the LP55xx DT structure supports max 3 channels.
However, LP5523 has max 9 channels and LP5562 has 4 channels.
To enhance this constraint, the DT structure has been changed.
(a) Use the child node for various channel settings instead of fixed array
(b) Remove 'num_channel' property.
This value can be retrieved by counting the children node.
(c) 'chan-name' property supported
(d) Documentation updates for LP5521 and LP5523
(cooloney@gmail.com: fix a coding style issue in leds-lp55xx.txt)
Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch allows the lp5521 driver to be successfully probed and
initialised when Device Tree support is enabled.
Based on a patch by Gabriel Fernandez, rewritten in accordance
with review feedback.
Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this
problem was found. It turned out that the released register
documentation is wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Switch to using SIMPLE_DEV_PM_OPS macro to declare the driver's
pm_ops. It reduces code size. Also, CONFIG_PM_SLEEP is added to
suspend/ resume functions to prevent build warnings when
CONFIG_PM_SLEEP is not selected.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/leds/leds-bd2802.c:766:12: warning: 'bd2802_suspend' defined but not used [-Wunused-function]
drivers/leds/leds-bd2802.c:776:12: warning: 'bd2802_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Now LP55xx provides automatic clock detection API, lp55xx_is_extclk_used().
The clock configuration can be done by the driver itself.
(a) Concept
The default value is set by each driver with clock selection.
The internal clock selection bit is updated in case that the external clock
is not detected or clock rate is not 32KHz.
(b) Change on LP55xx platform data
The clock configuration is done automatically, so no need to define
'update_config' in the platform side.
Correlated information are removed in the documentations and header.
(c) Definitions moved from header to driver files
CONFIG register values are moved each driver, LP5521 and LP5562.
Not necessary definitions are removed also.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Program execution is timed with 32768Hz clock in the LP55xx family devices.
To run LED functionalities, LP55xx devices provide two options.
One is using internal clock. The other is using external clock.
This patch enables external clock detection automatically.
If external clock is not detected, then the internal clock will be used in the
LP55xx driver.
Valid clock rate is 32768Hz in LP55xx devices.
This new API is used in each LP55xx driver like LP5521 and LP5562.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch fixes a regression introduced by commit 72052fcc10
("leds: leds-ns2: add device tree binding").
When the driver is initialized with device tree data, platform_data
pointer is NULL. This causes a kernel oops at removal.
To fix this bug, num_leds is moved into driver_data and platform_data
is not longer used from ns2_led_remove().
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Call to led_pwm_set() can happen inside atomic context, like triggers.
If the PWM call can sleep, defer using a worker.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
According to a sysfs documentation(Documentation/filesystem/sysfs.txt),
scnprintf() should be used in a read operation method.
It guarantees safe buffer size(PAGE_SIZE) which is allocated by the sysfs.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LM355x and LM3642 support flash and torch functionality.
(Camera driver) (LED trigger for camera) (LED driver)
Turn on the flash ...> ledtrig_flash_ctrl(true) ...> LM355x or LM3642
brightness ctrl
<actual driving here>
Flash/torch LEDs are controlled by other driver using LED camera trigger
APIs, ledtrig_flash_ctrl()/ledtrig_torch_ctrl().
Then, actual device control is activated by each LED driver such like
LM355x or LM3642.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some LED devices support flash/torch functionality through the LED subsystem.
This patch enables direct LED trigger controls by the driver.
Flash on/off and torch on/off can be done simply by other driver space.
Two trigger APIs are added, ledtrig_flash_ctrl() and ledtrig_torch_ctrl().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Provide some trace, though the hardware is most likely non-functional if
this happens.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | !!brightness
GPIOF_DIR_OUT and GPIOF_DIR_IN are defined as below:
GPIOF_DIR_OUT (0 << 0)
GPIOF_DIR_IN (1 << 0)
So, when '!!brightness' is 1, the gpio pin can be set as input,
instead of output.
To prevent this problem, GPIOF_OUT_INIT flags should be used when
using gpio_request_one().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | gpio_get_value(template->cmd)
GPIOF_DIR_OUT and GPIOF_DIR_IN are defined as below:
GPIOF_DIR_OUT (0 << 0)
GPIOF_DIR_IN (1 << 0)
So, when 'gpio_get_value(template->cmd)' is 1, the gpio pin can
be set as input, instead of output.
To prevent this problem, GPIOF_OUT_INIT flags should be used when
using devm_gpio_request_one().
Same goes for 'gpio_get_value(template->slow)' case.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | state
GPIOF_DIR_OUT and GPIOF_DIR_IN are defined as below:
GPIOF_DIR_OUT (0 << 0)
GPIOF_DIR_IN (1 << 0)
So, when 'state' is 1, the gpio pin can be set as input, instead
of output.
To prevent this problem, GPIOF_OUT_INIT flags should be used when
using devm_gpio_request_one().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
CONFIG_HOTPLUG was removed, so __devexit or __exit of remove()
should not be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
CONFIG_HOTPLUG was removed, so __devexit or __exit of remove()
should not be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
For better driver management, new subdirectory, 'trigger' is created.
All LED trigger drivers are moved into this directory.
Internal header, 'leds.h' is included in each LED trigger drivers.
Fix the location of header file, "leds.h" -> "../leds.h" in driver files.
One exception is here, 'ledtrig-timer.c'.
There is no need to include 'leds.h'. so '#include "leds.h"' line was removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5562 can drive up to 4 channels, RGB and White.
LEDs can be controlled directly via the led class control interface.
LP55xx common driver
LP5562 is one of LP55xx family device, so LP55xx common code are used.
On the other hand, chip specific configuration is defined in the structure
'lp55xx_device_config'
LED pattern data
LP5562 has also internal program memory which is used for running various LED
patterns. LP5562 driver supports the firmware interface and the predefined
pattern data as well.
LP5562 device attributes: 'led_pattern' and 'engine_mux'
A 'led_pattern' is an index code which runs the predefined pattern data.
And 'engine_mux' is updated with the firmware interface is activated.
Detailed description has been updated in the documentation files,
'leds-lp55xx.txt' and 'leds-lp5562.txt'.
Changes on the header file
LP5562 configurable definitions are added.
Pattern RGB data is fixed as constant value.
(No side effect on other devices, LP5521 or LP5523.)
(cooloney@gmail.com: remove redundant mutex_unlock(). Reported by Dan
Carpenter <dan.carpenter@oracle.com>)
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (61 commits)
leds: leds-sunfire: use dev_err()/pr_err() instead of printk()
leds: 88pm860x: Add missing of_node_put()
leds: tca6507: Use of_get_child_count()
leds: leds-pwm: make it depend on PWM and not HAVE_PWM
Documentation: leds: update LP55xx family devices
leds-lp55xx: fix problem on removing LED attributes
leds-lp5521/5523: add author and copyright description
leds-lp5521/5523: use new lp55xx common header
leds-lp55xx: clean up headers
leds-lp55xx: clean up definitions
leds-lp55xx: clean up unused data and functions
leds-lp55xx: clean up _remove()
leds-lp55xx: add new function for removing device attribtues
leds-lp55xx: code refactoring on selftest function
leds-lp55xx: use common device attribute driver function
leds-lp55xx: support device specific attributes
leds-lp5523: use generic firmware interface
leds-lp5521: use generic firmware interface
leds-lp55xx: support firmware interface
leds-lp55xx: add new lp55xx_register_sysfs() for the firmware interface
...
Fixed the checkpatch errors and warnings as below:
ERROR: spaces required around that '=' (ctx:VxW)
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
of_find_node_by_name() returns a node pointer with refcount incremented, use
of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against from parameter,
thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The correct dependency for the leds-pwm is PWM and not HAVE_PWM
since PWM drivers now have their own subsystem.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP55XX common device attributes, 'led_current' and 'max_current' are created
while loading the driver.
Those are LED device attributes which are removed automatically on releasing
led class devices - led_classdev_unregister().
Therefore, this duplicate code should be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Now LP5521 and LP5523 drivers are based on new lp55xx structure.
So the author and copyrights are updated.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Remove unused definitions and change hex values to capital letters
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Old data structures and I2C function are not used any more.
Each driver uses the lp55xx common data and functions.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Replace lp5521/5523_unregister_sysfs() with lp55xx_unregister_sysfs().
On unloading the driver, running engines should be stopped.
Use explicit driver function, lp5521/5523_stop_engine().
Unused functions are removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
lp55xx_unregister_sysfs() is used for removing lp55xx device attributes.
Chip specific and engine attributes are removed on unloading the driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5521 and LP5523 have a selftest function which is run via the sysfs.
Use lp55xx driver data and R/W functions rather than lp5521/5523 private data
and functions.
Additionally, if-statements are changed for code simplicity.
Unused functions, lp5521/5523_read() are removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
lp5521/5523_register_sysfs() are replaced with lp55xx common driver function,
lp55xx_register_sysfs().
Chip specific device attributes are configurable using 'dev_attr_group'.
Error condition name is changed:
use specific error condition, 'err_register_sysfs' rather than unclear name,
'fail2'.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To support device specific attributes, new common driver function is added.
Eventually those are created on registering the sysfs with common dev attrs.
Furthermore, this patch makes adding device attributes simple in each driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP55xx common driver provides generic firmware interface
for running a LED pattern.
LP5521 and LP5523 have many device attributes for running patterns.
This patch cleans up those complex code.
Removed device attributes:
engine1_mode
engine2_mode
engine3_mode
engine1_load
engine2_load
engine3_load
engine1_leds
engine2_leds
engine3_leds
All device attributes and functions are replaced with two callback functions,
'firmware_cb' and 'run_engine'.
New engine functions:
lp5523_load/stop/run_engine(), lp5523_update_program_memory() and
lp5523_wait_opmode_done()
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP55xx common driver provides generic firmware interface
for running a LED pattern.
LP5521 and LP5523 have many device attributes for running patterns.
This patch cleans up those complex code.
Removed device attributes:
engine1_mode
engine2_mode
engine3_mode
engine1_load
engine2_load
engine3_load
led_pattern
All device attributes and functions are replaced with two callback functions,
'firmware_cb' and 'run_engine'.
New engine functions:
lp5521_load/stop/run_engine(), lp5521_update_program_memory() and
lp5521_wait_opmode_done()
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch provides additional device attributes which enable
loading the firmware. ('select_engine' and 'run_engine')
To run a LED pattern, two parts of driver should be enabled.
Common features : lp55xx-common
===============================
Firmware interface for loading LED patterns
Chip specific features : leds-lp5521, leds-lp5523
=================================================
Register addresses for loading firmware data
Register addresses for running selected engine
Pattern programming sequence
============================
LP55xx chips have three program engines.
To load and run a LED pattern, the programming sequence is as follows.
(1) Select an engine number (1/2/3)
(2) Set engine mode to load
(3) Write pattern data into selected area
(4) Set engine mode to run
This sequence is almost same as the firmware interface.
(1) Select an engine number : 'select_engine' dev attribute
(2) Mode change to load : 'loading' of firmware class
(3) Write pattern data into selected area : 'data' of firmware class
(4) Mode change to run : 'run_engine' dev attribute
(1) and (4) are device specific features which provide callback functions
(2) and (3) are common features.
For example,
echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine
echo 1 > /sys/class/firmware/lp5521/loading
echo "4000600040FF6000" > /sys/class/firmware/lp5521/data
echo 0 > /sys/class/firmware/lp5521/loading
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
As soon as 'loading' is set to 0, registered callback is called.
Inside the callback, the selected engine is loaded and memory is updated.
To run programmed pattern, 'run_engine' attribute should be enabled.
Device specific data structure
==============================
o Firmware callback
load selected engine and update program memory
o Run engine
change the engine mode
o 'engine_idx' and firmware data, 'fw'
Those are used in the driver internally with callback functions
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP55xx family chips have internal program memory which run various patterns.
Using this memory, LEDs continue on blinking/dimming without continuous I2C
commands. That means the I2C HOST can be entered into sleep once the memory
is updated.
An application can get hex data from a file and write them into
the program memory through the I2C. This is general firwmare interface.
This patch is the initial step for adding the firmware interface.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use lp55xx_unregister_leds() rather than duplicate code.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To unregister led class devices and sysfs attributes,
LP5521 and LP5523 have each driver function.
This patch makes both drivers simple using common driver function,
lp55xx_unregister_leds().
And some unused variables are removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LED current is configurable via the sysfs.
Max current is a read-only attribute.
These attributes code can be shared in lp55xx common driver.
Device attributes: 'led_current' and 'max_current'
move to lp55xx common driver
Replaced functions:
show_max_current() => lp55xx_show_max_current()
show_current() => lp55xx_show_current()
store_current() => lp55xx_store_current()
LED setting function: set_led_current()
Current registers are device specific, so configurable function is added
in each driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
lp5521_set_brightness() and lp5523_set_brightness() are replaced with
common function, lp55xx_set_brightness().
This function is invoked when the brightness of each LED channel is updated.
LP5521 and LP5523 have different register address for the brightness control,
so this work is done by chip specific brightness_work_fn().
lp5521/5523_led_brightness_work():
use lp55xx_led and lp55xx_chip data structure.
use lp55xx write function.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
lp5521_init_led() and lp5523_init_led() are replaced with one common function,
lp55xx_init_led().
Max channels is configurable, so it's used in lp55xx_init_led().
'LP5523_LEDS' are changed to 'LP5523_MAX_LEDS'.
lp55xx_set_brightness, lp55xx_led_attributes: skeleton
Will be filled in next patches.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LED class devices are registered in lp5521_register_leds() and
lp5523_register_leds().
Two separate functions are merged into consolidated lp55xx function,
lp55xx_register_leds().
Error handling fix:
Unregistering LEDS are handled in lp55xx_register_leds() when LED registration
failure occurs. So each driver error handler is changed to 'err_register_leds'
Chip dependency: 'brightness_work_fn' and 'set_led_current'
To make the structure abstract, both functions are configured in each driver.
Those functions should be done by each driver because register control is
chip-dependant work.
lp55xx_init_led: skeleton
Will be filled in next patch
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Two separate de-init functions are merged into one common function.
And it is used in err_post_init of lp55xx_init_device().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
lp5521/5523_init_device() are replaced with lp55xx common function,
lp55xx_init_device().
Error handler in init_device:
deinit function are matched with 'err_post_init' section in
lp55xx_init_device().
Remove LP5523 engine intialization code:
Engine functionality is not mandatory but optional.
Moreover engine initialization is done internally with device reset command.
Therefore, this code is unnecessary.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5521/5523 chip configuration is replaced with lp55xx common function,
lp55xx_post_init_device().
Name change:
lp5521/5523_configure() to lp5521/5523_post_init_device()
These are called in init function.
Register access function
Argument type is changed from 'i2c_client' to 'lp55xx_chip'.
Use exported R/W functions of lp55xx common driver.
Temporary variables in lp5521/5523_init_device()
These functions will be removed but temporary variables are needed for
blocking build warnings - incompatible pointer.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5521/5523 chip detection functions are replaced with lp55xx common function,
lp55xx_detect_device().
Chip dependent address and values are configurable in each driver.
In init function, chip detection is executed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5521/5523 reset device functions are moved to lp55xx common driver.
Value of register address and value are chip dependent.
Those are configured in each driver.
In init function, reset command is executed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5521/5523 platform data functions are moved to lp55xx common driver.
New init function, lp55xx_init_device() is created.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch is a preceding step for making common lp55xx init function.
Return code:
Do not use 'OR' arithmetic for the result.
If some error occurs, just return it.
Remove engine verification code:
To check whether internal engine works or not, many lines of code are executed.
However, this job is unnecessary during the chip initialization because
the engine usage is not mandatory but optional function.
LED engines are enabled when specific LED pattern is loaded.
Therefore, this verification code is removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch is a preceding step for making common lp55xx init function.
LP5521_REG_R_CURRENT register code moved:
Chip specific code moved from lp5521_init_device() to lp5521_configure().
Remove engine init function:
LP5521 has internal program engines which are used for running LED patterns.
(blinking, ramp up/down and other emotional visual effects)
Engine initialization is done by reset command in lp5521_init_device().
Remove this duplicate code.
Return code:
Do not use 'OR' arithmetic for the result.
If some error occus, just return it.
Enable latency:
Use explicit named function, lp5521_wait_enable_done().
According to the datasheet, 500us is guaranteed time.
Thus wait time is changed from 1000us to 500us.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP5521 and LP5523 data structures have common features.
Use common lp55xx data structures rather than chip specific data.
Legacy code in probe is replaced with this new data structures.
lp55xx_chip : Common data between lp5521_chip and lp5523_chip
lp55xx_led : Common LED structure between lp5521_led and lp5523_led
lp55xx_platform_data : Common platform data between lp5521_platform_data and
lp5523_platform_data
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Change the name of chip data structure and platform data.
This patch is a preceding step for cleaning up lp5521/5523 probe and remove.
These data will be replaced with new lp55xx common data structures
in next patch.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch supports basic common driver code for LP5521, LP5523/55231 devices.
( Driver Structure Data )
lp55xx_led and lp55xx_chip
In lp55xx common driver, two different data structure is used.
o lp55xx_led
control multi output LED channels such as led current, channel index.
o lp55xx_chip
general chip control such like the I2C and platform data.
For example, LP5521 has maximum 3 LED channels.
LP5523/55231 has 9 output channels.
lp55xx_chip for LP5521 ... lp55xx_led #1
lp55xx_led #2
lp55xx_led #3
lp55xx_chip for LP5523 ... lp55xx_led #1
lp55xx_led #2
.
.
lp55xx_led #9
( Platform Data )
LP5521 and LP5523/55231 have own specific platform data.
However, this data can be handled with just one platform data structure.
The lp55xx platform data is declared in the header.
This structure is derived from leds-lp5521.h and leds-lp5523.h
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Chip specific function is configured when the device is initialized.
So _configure() is moved to each device init function.
If chip configuration gets failed, the device is de-initialized in
each _init_device(), not probe().
For compile error fix, function type declarations are added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Use explicit each driver function rather than raw command.
These function will be merged into the lp55xx common driver.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To make LED unregistration code simple, new function, _unregister_leds()
is added in each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To make LED initialization code simple, new function, _register_leds()
is added at each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Device de-initialization code is moved to _deinit_device() at each driver.
This patch is a preceding step for lp55xx common driver architecture.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
To make _probe() simple, device initialization code is moved to
_init_device() at each driver.
This patch is a preceding step for lp55xx common driver architecture.
leds-lp5521:
When 'lp5521_init_device()' gets failed, error handling should be 'fail1'
rather than 'fail2'.
fail1: releasing platform resource and return code
fail2: releasing allocated LED devices with handling 'fail1'
The 'lp5521_init_device()' is called before creating LED devices.
Thus, 'goto fail1' is proper error handler of this function.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This macro is used to create a struct pci_device_id array.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
I spent a few minutes to understand why the code catching the mismatch case
by checking if k is 0 or not. And the code using "k - 1" as array index is
unusual.
This patch checks acceptable rate from the lowest rate, and then we don't need
to subtract k by 1. This change improves the readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add lm3530_led_enable() and lm3530_led_disable() helper functions.
This ensures setting drvdata->enable to correct status if regulator_disable
fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo Kim <milo.kim@ti.com>
Tested-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The lp8788-keyled is a platform driver of lp8788-mfd. The platform
device is allocated when mfd_add_devices() is called in lp8788-mfd.
On the other hand, 'lp->dev' is the i2c client device.
Therefore, this 'platform_device' is a proper parent device in case
of resource managed mem alloc, registering led device and device
kernel messages.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The DT binding for the pwm-leds devices are similar to the gpio-leds type.
LEDs are represented as sub-nodes of the pwm-leds device.
The code for handling the DT boot is based on the code found in the
leds-gpio driver and adapted to use PWMs instead of GPIOs.
To avoid having custom cleanup code in case of DT boot the newly created
devm_of_pwm_get() API is used to get the correct PWM instance.
For usage see:
Documentation/devicetree/bindings/leds/leds-pwm.txt
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The code looks more nicer if we use:
while (i--)
instead:
if (i > 0)
for (i = i - 1; i >= 0; i--)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In order to be able to add device tree support for leds-pwm driver we need
to rearrange the data structures used by the drivers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Update the driver to use the new API for requesting pwm so we can take
advantage of the pwm_lookup table to find the correct pwm to be used for the
LED functionality.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Support added only for leds (not for gpio's).
(cooloney@gmail.com: fix 2 building errors)
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a99d76f leds: leds-gpio: use gpio_request_one
changed the leds-gpio driver to use gpio_request_one() instead
of gpio_request() + gpio_direction_output()
Unfortunately, it also made a semantic change that breaks the
leds-gpio driver.
The gpio_request_one() flags parameter was set to:
GPIOF_DIR_OUT | (led_dat->active_low ^ state)
Since GPIOF_DIR_OUT is 0, the final flags value will just be the
XOR'ed value of led_dat->active_low and state.
This value were used to distinguish between HIGH/LOW output initial
level and call gpio_direction_output() accordingly.
With this new semantic gpio_request_one() will take the flags value
of 1 as a configuration of input direction (GPIOF_DIR_IN) and will
call gpio_direction_input() instead of gpio_direction_output().
int gpio_request_one(unsigned gpio, unsigned long flags, const char *label)
{
..
if (flags & GPIOF_DIR_IN)
err = gpio_direction_input(gpio);
else
err = gpio_direction_output(gpio,
(flags & GPIOF_INIT_HIGH) ? 1 : 0);
..
}
The right semantic is to evaluate led_dat->active_low ^ state and
set the output initial level explicitly.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
If "buf" wasn't equal to LP5521_REG_R_CURR_DEFAULT the probe fails but
we still return zero. I've changed it to print an error message and
return -EINVAL.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Silences checkpatch warnings related to the use of printks.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following issues:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jan-Simon Moeller <jansimon.moeller@gmx.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following type of warnings:
WARNING: Prefer netdev_warn(netdev, ... then dev_warn(dev, ...
then pr_warn(... to printk(KERN_WARNING ...
WARNING: quoted string split across lines
While at it also fix a coding style issue w.r.t braces.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch error:
ERROR: space prohibited before that ':' (ctx:WxE)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ...
then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: please, no space before tabs
FILE: leds/leds-pwm.c:29:
^Iunsigned int ^I^Iactive_low;$
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(... to printk(KERN_INFO ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following checkpatch warning:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(... to printk(KERN_INFO ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch error and warnings:
WARNING: please, no space before tabs
ERROR: trailing whitespace
WARNING: quoted string split across lines
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fixes the following type of checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
devm_gpio_request_one is device managed and makes error handling
and cleanup simpler.
Cc: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
devm_gpio_request_one is device managed and makes error handling
and cleanup simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Return the value obtained from i2c_smbus_read_byte_data() instead of
-EINVAL. Silences the following smatch warning:
drivers/leds/leds-lp3944.c:89 lp3944_reg_read() info:
why not propagate 'tmp' from i2c_smbus_read_byte_data() instead of -22?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Return the value obtained from i2c_smbus_read_byte_data() instead of
-EIO. Silences the following smatch warning:
drivers/leds/leds-lp5523.c:174 lp5523_read() info:
why not propagate 'ret' from i2c_smbus_read_byte_data() instead of -5?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Return the value obtained from i2c_smbus_read_byte_data() instead of
-EIO. Silences the following smatch warning:
drivers/leds/leds-lp5521.c:155 lp5521_read() info:
why not propagate 'ret' from i2c_smbus_read_byte_data() instead of -5?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Implements a "led_trigger_rename" function to rename a trigger with
proper locking.
This assumes that led name was originally allocated in non-constant
storage.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
We don't need these sysfs files to be world writable or group writable.
These files are write-only, change them to S_IWUSR (0200).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
We don't need the sysfs file to be world writable or group writable.
This file is write-only, change it to S_IWUSR (0200).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_kfree function allocates memory that is released
when a driver detaches. Thus, there is no reason to explicitly
call devm_kfree in probe or remove functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch fixes build warnings as below:
drivers/leds/leds-lp5523.c: In function 'lp5523_selftest':
drivers/leds/leds-lp5523.c:496:18: warning: 'adc' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:471:5: warning: 'vdd' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c: In function 'lp5523_probe':
drivers/leds/leds-lp5523.c:252:9: warning: 'status' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-lp5523.c:201:5: note: 'status' was declared here
If lp5523_read() returns an error, problems will happen. Thus,
when lp5523_read() returns an error, it should be handled.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch makes leds-gpio's probe() return -EPROBE_DEFER if any of the gpios
to register are deferred themselves. This makes a change of
gpio_leds_create_of()'s return value necessary: Instead of returning NULL on
error, we now use ERR_PTR() error coding.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This makes the code smaller and a bit simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_ioremap() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_ioremap() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_ioremap() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Using gpio_request_one can make the code simpler because it can
set the direction and initial value in one shot.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds DT board setup for the LaCie NAS Network Space Mini v2
(aka SafeBox). The hardware characteristics are very close to those of
the Network Space Lite v2. The main difference are:
- A GPIO fan which is only available on the NS2 Mini.
- A single USB host port is wired on the NS2 Mini. The NS2 Lite provides
an additional dual-mode USB port (host/device).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds DT board setup for LaCie Network Space v2 and parents,
based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2
(Max) and Internet Space v2.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Seeing the following every time the CPU enters or leaves idle on a
Beagleboard:
BUG: sleeping function called from invalid context at kernel/mutex.c:269
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
no locks held by swapper/0/0.
[<c001659c>] (unwind_backtrace+0x0/0xf8) from [<c05aaa7c>] (mutex_lock_nested+0x24/0x380)
[<c05aaa7c>] (mutex_lock_nested+0x24/0x380) from [<c043bd1c>] (ledtrig_cpu+0x38/0x88)
[<c043bd1c>] (ledtrig_cpu+0x38/0x88) from [<c000f4b0>] (cpu_idle+0xf4/0x120)
[<c000f4b0>] (cpu_idle+0xf4/0x120) from [<c07e47c8>] (start_kernel+0x2bc/0x30c)
Miles Lane has reported seeing similar splats during system suspend.
The mutex in struct led_trigger_cpu appears to have no function: it
resides in a per-cpu data structure which never changes after the
trigger is registered. So just remove it.
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Bryan Wu <roc@roc-samos.(none)>
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (24 commits)
leds: add output driver configuration for pca9633 led driver
leds: lm3642: Use regmap_update_bits() in lm3642_chip_init()
leds: Add new LED driver for lm3642 chips
leds-lp5523: Fix riskiness of the page fault
leds-lp5523: turn off the LED engines on unloading the driver
leds-lm3530: Fix smatch warnings
leds-lm3530: Use devm_regulator_get function
leds: leds-gpio: adopt pinctrl support
leds: Add new LED driver for lm355x chips
leds-lp5523: use the i2c device id rather than fixed name
leds-lp5523: add new device id for LP55231
leds-lp5523: support new LP55231 device
leds: triggers: send uevent when changing triggers
leds-lp5523: minor code style fixes
leds-lp5523: change the return type of lp5523_set_mode()
leds-lp5523: set the brightness to 0 forcely on removing the driver
leds-lp5523: add channel name in the platform data
leds: leds-gpio: Use of_get_child_count() helper
leds: leds-gpio: Use platform_{get,set}_drvdata
leds: leds-gpio: use of_match_ptr()
...
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO7aAAoJEIwa5zzehBx3bUIP/02U8PhkHJJrrowyIsWRBOql
7LPJ53PRRgrpBdmEGzFD3TO3zaNyrjQRbYgNDvzHMO6NAMNvdRFouuWYjO11/tuB
i32zssXCC+eUOEgbAo/U/lYq+UOvqw9gv6mU+3+i3OcGEhdKOaoT/DSLPQC4hoDm
222TeLfFB3HJXu5n720dEQ9V3fO6TS1+bbh8TU3cjHqzceXsOrffZqOA5CQxUcRr
KWwOjA0nALDwWcqgv45GJNwY3GTyAQ/hPMQavnuWK0voJ+qUYk5HftKocAK7C+py
0T0OFOAHTwtyhvzJBxLC84M6Ox465BYXyeNjIB+2nG/Um9+mDoP0dnWpGy4c7DMU
P5hyqbeLGeqjUXQuYtRmgMMc3UeHKoUGAfXW9eMsjLa6/M4NLGv//7E7LbZPpgMZ
obkjwuesmcaYn/FRyj/yFmC35YlF4oCLziVzEtURZw3eKHHSUlhkTDSMNnkcZ0kZ
Vv7kFxnD2Y46ixiwSJv30ErQnVkgI3MdqDlDxkE8r5+phYuK4gCrNaJtiwRh/oNw
cFhpPxKuA0sJ9b6YRTzjC45eT/XZomEEr/uifCFeRNaCquyjYP00Mm8F0flSqwx9
zi+emzPAwNmk1bvxMUM/idGnaj0V4p+BAYUAvkbSoqU1p1flzyhU88fGTSIyKOt6
K5TCDS2v5hrVykK9TDwl
=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
the pca9633 leds driver can be used in open-drain or totem pole (a.k.a.
push/pull) output driver mode; default is the later
the patch allows to set the output driver mode using platform data (similar to
configuration inferface provided by the tca6507 led driver)
v2: move leds-pca9633.h to include/linux/platform_data/ (Bryan Wu)
Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Use regmap_update_bits() to replace regmap_read() + regmap_write().
With this patch, we only show the error message when regmap_update_bits()
fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: G.Shark Jeong<gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the orion include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=6+9B
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver is a general version for LM642 led chip of TI.
LM3642 :
The LM3642 is a 4MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current
white LED.
The LM3642 is controlled via an I2C-compatible interface.
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The last attribute should be terminated as NULL because any member of
attribute structure is accessed while adding the sysfs file.
If not, invalid address may cause the page fault problem.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The LP5523 has 3 engines which are used for running LED patterns.
These engines should be off while unloading the driver.
Obviously, LP5523 platform data are used for releasing the resource
such like enable()/release_resource(), but these are not mandatory.
Therefore this patch is required without the platform data dependency.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Device managed functions are already used in this file.
Hence convert regulator_get() too to use it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Adopt pinctrl support to leds-gpio driver based on leds-gpio
device pointer, pinctrl driver configure SoC pins to GPIO
mode according to definitions provided in .dts file.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This driver is a general version for LM355x,lm3554 and lm3556,led chips of TI.
LM3554 :
The LM3554 is a 2 MHz fixed-frequency synchronous boost
converter with 1.2A dual high side led drivers.
Datasheet: www.ti.com/lit/ds/symlink/lm3554.pdf
LM3556 :
The LM3556 is a 4 MHz fixed-frequency synchronous boost
converter plus 1.5A constant current driver for a high-current white LED.
Datasheet: www.national.com/ds/LM/LM3556.pdf
(bryan.wu@canonical.com: use flush_work() to replace flush_work_sync() which is
deprecated)
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
LP5523 driver supports both LP5523 and LP55231. The i2c device id
is one of the two - lp5523 or lp55231. So it's better to use
matching i2c device id while enumerating the device and naming LED
channels.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
To support LP55231 device, the device id is added. Additionally,
the i2c driver name is changed from lp5523 to lp5523x.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
New TI LP55231 device has same I2C register layout as LP5523. Therefore,
all of LED operations can be shared with the LP5523 driver.
To support new LP55231 device explicitly, the device description
is added in the configuration file.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Some triggers create sysfs files when they are enabled. Send a uevent
"change" notification whenever the trigger is changed to allow userspace
processes such as udev to modify permissions on the new files.
A change notification will also be sent during registration of led class
devices or led triggers if the default trigger of an led class device
is found.
(bryan.wu@canonical.com: rename trigger to trig to fix the build error)
Signed-off-by: Colin Cross <ccross@android.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
(a) use LP5523_ENABLE rather than magic number 0x40
(b) use min_t() in lp5523_mux_parse()
(c) skip while loop and just return if invalid command
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The return value of this function is not handled any place, so
make it as void type.
And three if-statements are replaced with switch-statements.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Turning off the brightness of each channel is required
when removing the driver.
So use flush_work() rather than cancel_work_sync() to execute
remaining brightness works.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
The name of each led channel is configurable.
If the name is NULL, just use the channel id for making the channel name
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Use the wrapper functions, so we can directly pass a struct
platfrom_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Instead of having to define the match table to NULL if CONFIG_OF isn't
set, use the of_match_ptr() macro which will do this for us.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Delay execution of led_set_brightness() if need to stop soft-blink
timer.
This allows led_set_brightness to be called in hard-irq context even if
soft-blink was activated on that LED.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
There are more variants of Clevo M5x0V laptops and Positivo Mobile is just one of them.
Another one is UMAX VisionBook 2400WXC. Use only generic Clevo DMI strings to match all
variants.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Enable autoloading of leds-clevo-mail by using MODULE_DEVICE_TABLE.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Since the resources of 88pm860x leds are changed from IORESOURCE_IO
to IORESOURCE_REG that is register offset, change the original
self-defined IORESOURCE_IO to register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
From Bryan Wu <bryan.wu@canonical.com>:
Based on Linus Walleij's ARM LED consolidation work, this patchset introduce a
new generic led trigger for CPU not only for ARM but also for others.
For enabling CPU idle event, CPU arch code should call ledtrig_cpu() stub to
trigger idle start or idle end event.
These patches convert old style LED driver in arch/arm to gpio_led or new led
driver interface. Against 3.5 release and build successfully for all the machines.
Test ledtrig-cpu driver on OMAP4 Panda board.
v9 --> v10
* fix compiling issue on versatile_defconfig reported by Russell King
* rebase to 3.5 kernel and move patches to new git tree
v8 --> v9:
* use mutex to replace rw_sema pointed out by Tim Gardner
* add a new struct led_trigger_cpu
* add lock_is_inited to record mutex lock initialization
v6 --> v7:
* add a patch to unify the led-trigger name
* fix some typo pointed
* use BUG_ON to detect CPU numbers during building stage
v5 --> v6:
* replace __get_cpu_var() to per_cpu()
* remove smp_processor_id() which is wrong with for_each_possible_cpu()
* test on real OMAP4 Panda board
* add comments about CPU hotplug in the CPU LED trigger driver
v4 --> v5:
* rebase all the patches on top of latest linux-next
* replace on_each_cpu() with for_each_possible_cpu()
* add some description of ledtrig_cpu() API
* remove old leds code from driver nwflash.c, which should use a new led trigger then
* this trigger driver can be built as module now
v3 --> v4:
* fix a typo pointed by Jochen Friedrich
* fix some building errors
* add Reviewed-by and Tested-by into patch log
v2 --> v3:
* almost rewrote the whole ledtrig-cpu driver, which is more simple
* every CPU will have a per-CPU trigger
* cpu trigger can be assigned to any leds
* fix a lockdep issue in led-trigger common code
* other fix according to review
v1 --> v2:
* remove select operations in Kconfig of every machines
* add back supporting of led in core module of mach-integrator
* solidate name scheme in ledtrig-cpu.c
* add comments of CPU_LED_* cpu led events
* fold patches of RealView and Versatile together
* add machine_is_ check during assabet led driver init
* add some Acked-by in patch logs
* remove code for simpad machine in machine-sa11000, since Jochen Friedrich
introduced gpiolib and gpio-led driver for simpad
* on Assabet and Netwinder machine, LED operations is reversed like:
setting bit means turn off leds
clearing bit means turn on leds
* add a new function to read CM_CTRL register for led driver
* 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ARM: use new LEDS CPU trigger stub to replace old one
ARM: mach-sa1100: retire custom LED code
ARM: mach-omap1: retire custom LED code
ARM: mach-pnx4008: remove including old leds event API header file
ARM: plat-samsung: remove including old leds event API header file
ARM: mach-pxa: retire custom LED code
char: nwflash: remove old led event code
ARM: mach-footbridge: retire custom LED code
ARM: mach-ebsa110: retire custom LED code
ARM: mach-clps711x: retire custom LED code of P720T machine
ARM: mach-integrator: retire custom LED code
ARM: mach-integrator: move CM_CTRL to header file for accessing by other functions
ARM: mach-orion5x: convert custom LED code to gpio_led and LED CPU trigger
ARM: mach-shark: retire custom LED code
ARM: mach-ks8695: remove leds driver, since nobody use it
ARM: mach-realview and mach-versatile: retire custom LED code
ARM: at91: convert old leds drivers to gpio_led and led_trigger drivers
led-triggers: create a trigger for CPU activity
Conflicts:
arch/arm/mach-clps711x/p720t.c
arch/arm/mach-sa1100/leds-cerf.c
arch/arm/mach-sa1100/leds-lart.c
Let's hope this is the last time we pull this and it doesn't cause
more trouble. I have verified that version 10 causes no build
warnings or errors any more, and the patches still look good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
bfe4c041 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This reverts commit a0193cbee0.
The problem with the original commit was that it caused a warning with
the MMC trigger calling del_timer_sync from hard-irq context.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Reported-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
We need to do left shift (cfg->num + LP8788_ISINK_SCALE_OFFSET) bits for
updating scale configuration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Attempting to consolidate the ARM LED code, this removes the
custom RealView LED trigger code to turn LEDs on and off in
response to CPU activity and replace it with a standard trigger.
(bryan.wu@canonical.com:
It introduces several syscore stubs into this trigger.
It also provides ledtrig_cpu trigger event stub in <linux/leds.h>.
Although it was inspired by ARM work, it can be used in other arch.)
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Jochen Friedrich <jochen@scram.de>
at default case of switch we return with out unlocking the mutex.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Jingoo Han