Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUjgQ7AAoJEEEQszewGV1zuJ8P+wamlDNhJbsgqXPcSCZZFgeP
1O22VRYqoo/i8mAzNCRi2h6NogO9Da6rCRhHdH35TsuNzIbusHE+btMukj248qJ7
WYOf25I0ImyUP8kulogW4/+7lYibRLHnN2BSLuAkApofmxDvODPS1KNWHulcOcxl
VaVsA8wvFzQO1s1Wjv94ctVfs5rqk7mBfPwk61zHuLeETecmKg0e52p0Uzqlq6gi
UKi9uK3sjQ7kI/+xa+qDrF9GRwRR22oJfD/9zNj8g94iU9iMs5Oh+Zp3RJcvYUSD
y5BIb+IY2ATy20ZkijWmeP8LJz6pja+C9Ne7lKM0jkv7geGeHGAoavz0n3oUq4oz
IvUNz6hCAP9PcxWc5a9FFqqORLWrRew6GmZmJvIkmC9K+3UQcWhkzO3vLpfl6Q9h
S728XexkIlhxG9NcER21bFXV2dw3z/X9dm5mQ473TqJm+wQmRuYcPRg053NbqMcx
juvkweCksx8qlpnjo/1QXQcVwFM8kuR7xAlVo7zdMDOU5F8pdxRnsTl0cUdx5cPv
DKeMRg8+FYcHmIoe/EodemIh7cAZtEpijZNNAr9cDmAjifeBjWhCb+zri5SIc96x
0jKVTXyY4jnHXBVoA0FIl1d2t54yVjh3PYiu0MjeLJ9tyB+Px/nOxW8FrdlFnPJ/
oP5WK13c8h3bMkxUzsvL
=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
The A80 has a rather usual pin controller, the only thing out of the ordinary
being that it has 5 interrupts banks, and that some pins have several options
for the same functions.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A80 R-PIO controller has one more bank that what we've seen so far, add the
PN pin bank.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 2243a87d90
"pinctrl: avoid duplicated calling enable_pinmux_setting for a pin"
removed the .disable callback from the struct pinmux_ops,
making the .enable() callback the only remaining callback.
However .enable() is a bad name as it seems to imply that a
muxing can also be disabled. Rename the callback to .set_mux()
and also take this opportunity to clean out any remaining
mentions of .disable() from the documentation.
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Fan Wu <fwu@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
development cycle:
- Get rid of the .disable() callback from the driver callback
vtable. This callback was abused and counterintuitive since
a pin or group of pins can be said to always be in some
setting, and never really disabled. We now only enable a
certain muxing, and move between some certain muxings, we
never "disable" a mux setting.
- Some janitorial moving the MSM, Samsung and Nomadik and
drivers to their own subdirectories for a clearer view in
the subsystem. This will continue.
- Kill off the use of the return value from gpiochip_remove(),
this will be done in parallel in the GPIO subsystem and
hopefully not trigger too many unchecked return value
warnings before we get rid of this altogether.
- A huge set of changes and improvements to the Allwinner
sunxi drivers especially for their latest A23 and A31 SoCs,
and some ground work for the new sun8i platform family.
- A large set of Rockchip driver improvements adding support
for the RK3288 SoC.
- Advances in migration of older Freescale platforms to pin
control, especially i.MX1.
- Samsung and Exynos improvements.
- Support for the Qualcomm MSM8960 SoC.
- Use the gpiolib irqchip helpers for the ST SPEAr and
Intel Baytrail drivers.
- A bunch of nice janitorial work done with cppcheck.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t1pR
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"This is the bulk pin control changes for the v3.17 merge development
cycle:
- get rid of the .disable() callback from the driver callback vtable.
This callback was abused and counterintuitive since a pin or group
of pins can be said to always be in some setting, and never really
disabled. We now only enable a certain muxing, and move between
some certain muxings, we never "disable" a mux setting
- some janitorial moving the MSM, Samsung and Nomadik and drivers to
their own subdirectories for a clearer view in the subsystem. This
will continue
- kill off the use of the return value from gpiochip_remove(), this
will be done in parallel in the GPIO subsystem and hopefully not
trigger too many unchecked return value warnings before we get rid
of this altogether
- a huge set of changes and improvements to the Allwinner sunxi
drivers especially for their latest A23 and A31 SoCs, and some
ground work for the new sun8i platform family
- a large set of Rockchip driver improvements adding support for the
RK3288 SoC
- advances in migration of older Freescale platforms to pin control,
especially i.MX1
- Samsung and Exynos improvements
- support for the Qualcomm MSM8960 SoC
- use the gpiolib irqchip helpers for the ST SPEAr and Intel Baytrail
drivers
- a bunch of nice janitorial work done with cppcheck"
* tag 'pinctrl-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (61 commits)
pinctrl: baytrail: Convert to use gpiolib irqchip
pinctrl: sunxi: number gpio ranges starting from 0
pinctrl: sunxi: use gpiolib API to mark a GPIO used as an IRQ
pinctrl: rockchip: add drive-strength control for rk3288
pinctrl: rockchip: add separate type for rk3288
pinctrl: rockchip: set is_generic in pinconf_ops
pinctrl: msm: drop negativity check on unsigned value
pinctrl: remove all usage of gpio_remove ret val in driver/pinctl
pinctrl: qcom: Make muxing of gpio function explicit
pinctrl: nomadik: move all Nomadik drivers to subdir
pinctrl: samsung: Group all drivers in a sub-dir
sh-pfc: sh73a0: Introduce the use of devm_regulator_register
sh-pfc: Add renesas,pfc-r8a7791 to binding documentation
pinctrl: msm: move all qualcomm drivers to subdir
pinctrl: msm: Add msm8960 definitions
pinctrl: samsung: Allow pin value to be initialized using pinfunc
pinctrl: samsung: Allow grouping multiple pinmux/pinconf nodes
pinctrl: exynos: Consolidate irq_chips of GPIO and WKUP EINTs
pinctrl: samsung: Handle GPIO request and free using pinctrl helpers
pinctrl: samsung: Decouple direction setting from pinctrl
...
The pinctrl-sunxi driver originally used the pin number as the gpio
range offset. This resulted in large, bogus gpio numbers for the
new sun6i-a31-r pinctrl devices.
This patch makes the driver number the gpios ranges starting from an
offset of 0, by subtracting the pin_base number from the pin number.
This also makes the system-wide gpio number match the pin number.
Tested on sun8i with sysfs exported gpios.
This patch also changes the GPIO bindings for R_PIO:
gpios = <&r_pio B N flag>;
Where B originally was the pinbank label (L or M) counted from A,
with this patch it becomes (L or M) counted from its pinbank base (L).
Thus
gpios = <&r_pio 10 11 0>; /* PL11 */
becomes
gpios = <&r_pio 0 11 0>; /* PL11 */
IMO this is correct, as the binding shows the bank offset and pin offset
within the bank for the GPIO controller. But I'm worried it might be a
bit confusing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an IRQ is started on a GPIO line, mark this GPIO as IRQ in
the gpiolib so we can keep track of the usage centrally.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 has a R_PIO pin controller, similar to the one found on the A31 SoC.
Add support for the pins controlled by the R_PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 uses the same pin controller as previous SoC's from Allwinner.
Add support for the pins controlled by the main PIO controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PINCTRL_SUNXI configuration was kept only to deal with the introduction of
per-machine symbols and the various pintrl drivers through different tree.
Now that it's not useful anymore, we can just remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A13 user manual states pins PG0/1/2 only have GPIO input and
interrupt functions. Remove the gpio_out functions for these pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When mapping the interrupts, the gpio_to_irq function did not consider
the bank number of the gpio pin in question, only the offset or the
interrupt number in the bank. As a result, requests for interrupts in
the later banks get mapped to the first bank.
This issue was discovered while enabling mmc on the new sun8i platform.
The tablet I have uses a pin/interrupt from the second bank to do mmc
card detection. Tested on this very device with register inspection and
actual mmc card insertion/removal.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers use disable_irq / enable_irq and do the work
clearing the source in another thread instead of using a threaded
interrupt handler.
The irqchip used not having irq_disable and irq_enable
callbacks in this case, will lead to unnecessary spurious
interrupts:
On a disable_irq in a chip without a handler for this, the irq
core will remember the disable, but not actually call into the
irqchip. With a level triggered interrupt (where the source has
not been cleared) this will lead to an immediate retrigger, at
which point the irq-core will mask the irq. So having an
irq_disable callback in the irqchip will save us the interrupt
firing a 2nd time for nothing.
Drivers using disable / enable_irq like this, will call
enable_irq when they finally have cleared the interrupt source,
without an enable_irq callback, this will turn into an unmask,
at which point the irq will trigger immediately because when it
was originally acked the level was still high, so the ack was
a nop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For level triggered gpio interrupts we need to use handle_fasteoi_irq,
like we do with the irq-sunxi-nmi driver. This is necessary to give threaded
interrupt handlers a chance to actuall clear the source of the interrupt
(which may involve sleeping waiting for i2c / spi / mmc transfers), before
acknowledging the interrupt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With level triggered interrupt mask / unmask will get called for each
interrupt, doing the somewhat expensive mux setting on each unmask thus is
not a good idea. Instead add a request_resources callback and do it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sunxi pinctrl irq chip driver does not support wakeup at the
moment. Adding IRQCHIP_SKIP_SET_WAKE lets the irqs work with drivers
using wakeup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 and A31 support multiple interrupt banks. Support it by adding a linear
domain covering all the banks. It's trickier than it should because there's an
interrupt per bank, so we have multiple interrupts using the same domain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The primary pinctrl device has 4 interrupt banks. As usual, to be able to
generate interrupts, the pins supporting it need to be muxed to a special
function. Declare these functions in the pins array.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Declare in the description structure associated to the compatible the number of
interrupt banks the device has. For now, we're not doing anything with it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 and A23, unlike the other Allwinner SoCs, have several interrupts banks
and parent interrupts, while the other only have up to 32 interrupts in a
single bank and a single parent interrupt.
Start supporting it by introducing a function macro to declare irq functions
and their banks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If irq_mask_ack is not defined, mask_ack_irq will call irq_mask and then
irq_ack. In order to avoid code duplication, between irq_mask_ack and irq_mask,
just declare irq_ack.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kzalloc can fail. Add a null check to avoid null pointer
dereference error while accessing the pointer later.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq/pin mapping is used to lookup the pin to mux to the irq
function when the irq is enabled. It is created when gpio_to_irq
is called. Creating the mapping during init allows us to map the
interrupts directly from the device tree.
Originally the IRQ to pin mapping was created when gpio_to_irq
was called with a GPIO handle. The mapping in turn is used to mux
the pin into EINT mode.
If the mapping is created during gpio_to_irq, we can't use the
interrupts directly, i.e. through the DT with "interrupts = <&pio A 4>".
Instead we'd have to use "gpios = <&pio A B>", then pass the gpio
through to gpio_to_irq.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A31 R_PIO driver depends on the reset framework in a mandatory way. Express
this by adding a depends on the reset framework in Kconfig
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin numbers passed to sunxi_*_reg helpers to get the correct
registers should be the pin offset for the PIO block, not the
absolute number we use that is based on the alphanumeric labels
Allwinner uses.
This patch subtracts .pin_base from the pin number passed to these
functions, so the driver accesses the correct registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the support for the PRCM muxer on the A31 has been added, the global
static pinctl_desc definition has been left as is. Unfortunately, this
structure is used to register the pinctrl device, and prior to this
registration, we set the name and pins field.
Since this structure is shared across instances, that means that the latest
registered pinctrl device wins in setting the name, pins and pins numbers,
which is not really a good thing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following configuration error:
drivers/pinctrl/sunxi/Kconfig:3:error: recursive dependency detected!
drivers/pinctrl/sunxi/Kconfig:3: symbol PINCTRL_SUNXI is selected by PINCTRL_SUN4I_A10
drivers/pinctrl/sunxi/Kconfig:9: symbol PINCTRL_SUN4I_A10 default value contains PINCTRL_SUNXI
Add a new intermedia PINCTRL_SUNXI_COMMON, that superseeds the PINCTRL_SUNXI
one.
We still need to keep PINCTRL_SUNXI at the moment in order to preserve
bisectability. Indeed, during that merge window, we also introduced the
MACH_SUN* symbols. Since it's going through different trees, we can't rely on
the fact that the options will be there, while ARCH_SUNXI still select
PINCTRL_SUNXI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable the freshly introduced Kconfig options whenever their matching
architecture is enabled.
Since the Kconfig symbols for these machines are going through a different
tree, keep PINCTRL_SUNXI around for the moment to avoid breaking the defconfig.
It should be removed eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The way that reset is handled right now is that it is made optional for every
pinctrl driver, while actually, it isn't used at all for the main pin
controllers so far, and while it's mandatory for the A31's secondary pin
controller.
Move the reset functions out of the core and in the driver, where they can be
made mandatory.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add one Kconfig option for each driver. This will allow to better control which
driver is enabled, instead of having either all or nothing.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be.
This is the final step toward retiring pinctrl-sunxi-pins.h that used to define
all the pins for all the Allwinner SoCs in a single header, that would have in
turn result in having these structures in the final binary as many times as the
header was included.
We can finally remove that header, and remove all the driver part of the
pinctrl-sunxi core.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This will allow to have multiple drivers using the same core code, and
eventually, retire pinctrl-sunxi-pins.h
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The previous code was calling of_iomap, which doesn't do any resource
management, and doesn't call request_mem_region either. Use
devm_ioremap_resource that do both.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We previously had an evergrowing (and exhaustive) list of the pins that could
be used on any Allwinner SoCs. These defines were then used by each pinctrl
driver to declare the list of functions for this pin. Since it's pretty much
all boilerplate, we can remove it just by a single macro.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Linus Torvalds