ddbridge has a few MDIO related remainders (defines, hwinfo struct) which
aren't of any use for the in-kernel driver at all (they're only used in
conjunction with the OctoNet SAT>IP boxes which the kernel driver doesn't
have any support for), so clean this up.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The I2C_COMMAND response reports an error in the I2C bus communication
using bit 17. Evaluate the response more thoroughly and log an error
if an I2C problem was detected.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Devices supporting dummy tuner operation can exist on any link, not only
on link 0, so fix this accordingly.
Picked up from the upstream dddvb GIT.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In demod_attach_stv0910(), the LNBH25 IC is being blindly attached and,
if the result is bad, blindly attached on another possible I2C address.
The LNBH25 uses it's set_voltage function to test for the IC and will
print an error to the kernel log on failure. Prevent this by probing
the possible I2C address and use this (and only this) to attach the
LNBH25 I2C driver. This also allows the stv0910 attach function to be
a bit cleaner.
Picked up from the upstream dddvb GIT and adapted for the LNBH25 driver
variant from the kernel tree.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Found and reported by kbuild test robot:
Message ID: <201805052003.MC007f9h%fengguang.wu@intel.com>
and holding an address of an empty struct in .driver.pm does no harm
when CONFIG_PM_SLEEP is not defined.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ivtv_probe() and ivtvfb_init_card() are never called in atomic context.
They call kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dvb_register() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx88_card_setup_pre_i2c() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx25821_gpio_init(), cx25821_initialize() and cx25821_registers_init()
are never called in atomic context.
They call mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx23885_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cx23885_gpio_setup() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep() and usleep_range().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
altera_ci_slot_reset() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cobalt_probe() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The same code is executed regardless of whether c->frequency < 600000000
or c->frequency < 730000000 is true.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 1eace8344c ("i2c: add param sanity check to
i2c_transfer()"), the I2C core does this check now. We can remove it
from drivers.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The error path currently calls tw686x_video_free() which requires
vc->dev to be initialized, causing a NULL dereference on uninitizalized
channels.
Fix this by setting the vc->dev fields for all the channels first.
Fixes: f8afaa8dbc ("[media] tw686x: Introduce an interface to support multiple DMA modes")
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We need to zero-initialize cx25840 platform data structure to make sure
that its future members do not contain random stack garbage.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver does not serialize its video4linux
ioctls, which is a bug, as race conditions might appear.
In addition, video_device and vb2_queue locks are now both
mandatory. Add them, and implement wait_prepare and
wait_finish.
To stay on the safe side, this commit uses a single mutex
for both locks. Better latency can be obtained by separating
these if needed.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When snd_ctl_add fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling snd_ctl_add.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check for a zero retval is redundant as all paths that lead to
this point have set retval to an error return value that is non-zero.
Remove the redundant check.
Detected by CoverityScan, CID#102589 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Trivial fix to spelling mistake in pr_notice message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Those two files are unused since commit 486a7a2813 ("[media] cx25821: remove cx25821-audio-upstream.c")
and commit b6f21dc354 ("[media] cx25821: remove video output support")
Remove them from tree.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several places pointing to old documentation files:
Documentation/video4linux/API.html
Documentation/video4linux/bttv/
Documentation/video4linux/cx2341x/fw-encoder-api.txt
Documentation/video4linux/m5602.txt
Documentation/video4linux/v4l2-framework.txt
Documentation/video4linux/videobuf
Documentation/video4linux/Zoran
Make them point to the new location where available, removing
otherwise.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This script was moved out of Documentation/dvb, but the
links weren't updated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----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=r/WP
-----END PGP SIGNATURE-----
Merge tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- remove of atomisp driver from staging, as nobody would have time to
dedicate huge efforts to fix all the problems there. Also, we have a
feeling that the driver may not even run the way it is.
- move Zoran driver to staging, in order to be either fixed to use VB2
and the proper media kAPIs or to be removed
- remove videobuf-dvb driver, with is unused for a while
- some V4L2 documentation fixes/improvements
- new sensor drivers: imx258 and ov7251
- a new driver was added to allow using I2C transparent drivers
- several improvements at the ddbridge driver
- several improvements at the ISDB pt1 driver, making it more coherent
with the DVB framework
- added a new platform driver for MIPI CSI-2 RX: cadence
- now, all media drivers can be compiled on x86 with COMPILE_TEST
- almost all media drivers now build on non-x86 architectures with
COMPILE_TEST
- lots of other random stuff: cleanups, support for new board models,
bug fixes, etc
* tag 'media/v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
media: omap2: fix compile-testing with FB_OMAP2=m
media: media/radio/Kconfig: add back RADIO_ISA
media: v4l2-ioctl.c: fix missing unlock in __video_do_ioctl()
media: pxa_camera: ignore -ENOIOCTLCMD from v4l2_subdev_call for s_power
media: arch: sh: migor: Fix TW9910 PDN gpio
media: staging: tegra-vde: Reset VDE regardless of memory client resetting failure
media: marvel-ccic: mmp: select VIDEOBUF2_VMALLOC/DMA_CONTIG
media: marvel-ccic: allow ccic and mmp drivers to coexist
media: uvcvideo: Prevent setting unavailable flags
media: ddbridge: conditionally enable fast TS for stv0910-equipped bridges
media: dvb-frontends/stv0910: make TS speed configurable
media: ddbridge/mci: add identifiers to function definition arguments
media: ddbridge/mci: protect against out-of-bounds array access in stop()
media: rc: ensure input/lirc device can be opened after register
media: rc: nuvoton: Keep device enabled during reg init
media: rc: nuvoton: Keep track of users on CIR enable/disable
media: rc: nuvoton: Tweak the interrupt enabling dance
media: uvcvideo: Support realtek's UVC 1.5 device
media: uvcvideo: Fix driver reference counting
media: gspca_zc3xx: Enable short exposure times for OV7648
...
CineS2 V7(A) and Octopus CI S2 Pro/Advanced cards support faster TS speeds
on the card's contained stv0910 demodulator when their FPGA was updated
with a recent (>= 1.7, version number applies to all mentioned cards)
vendor firmware. Enable this faster TS speed on card port 0 (contained
demod) and parallel stv0910 connections when the card firmware is at least
1.7 or later.
Note: The mentioned cards and their demods are handled via the STV0910_PR
and STV0910_P tuner types. DuoFlex modules with such demodulators are
handled via the STV0910 (without suffix) types where such TS speed
increase doesn't technically make sense.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Helmut Auer <post@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a tsspeed config option to struct stv0910_cfg which can be used by
users of the driver to set the (parallel) TS speed (higher speeds enable
support for higher bitrate transponders). If tsspeed isn't set in the
config, it'll default to a sane value.
This commit also updates the two consumers of the stv0910 driver (ngene
and ddbridge) to have a default tsspeed in their stv0910_cfg templates.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Tested-by: Helmut Auer <post@helmutauer.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixes two checkpatch warnings
WARNING: function definition argument 'xxx' should also have an identifier name
in the ddb_mci_attach() prototype definition. checkpatch keeps complaining
on the "int (**fn_set_input)" as it seems to have issues with the
ptr-to-ptr, though this probably needs fixing in checkpatch.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In stop(), an (unlikely) out-of-bounds write error can occur when setting
the demod_in_use element indexed by state->demod to zero, as state->demod
isn't checked for being in the range of the array size of demod_in_use, and
state->demod maybe carrying the magic 0xff (demod unused) value. Prevent
this by checking state->demod not exceeding the array size before setting
the element value. To make the code a bit easier to read, replace the magic
value and the number of array elements with defines, and use them at a few
more places.
Detected by CoverityScan, CID#1468550 ("Out-of-bounds write")
Thanks to Colin for reporting the problem and providing an initial patch.
Fixes: daeeb1319e ("media: ddbridge: initial support for MCI-based MaxSX8 cards")
Reported-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the driver is configured in the "memcpy" dma-mode,
it uses vb2_vmalloc_memops, which is backed by a SLAB
allocator and so shouldn't be using GFP_DMA32.
Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Note:
- The various VIDEOBUF*DMA* symbols had to loose their dependencies on
HAS_DMA, as they are selected by several individual drivers.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver hasn't been tested in a long, long time. The hardware is
ancient and pretty much obsolete. This driver also needs to be converted
to newer media frameworks (vb2!) but due to the lack of time and interest
that is unlikely to happen.
So this driver is a prime candidate for removal. If someone is interested
in working on this driver to prevent its removal, then please contact the
linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Document what these two register calls are doing.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Include some additional useful registers in the output.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently mask is read for pci_status/ts1_status/ts2_status, but
otherwise ignored. The masks are now used to determine whether
action is warranted.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On Ryzen systems interrupts are occasionally missed:
cx23885: cx23885_wakeup: [ffff99b384b83c00/28] wakeup reg=5406 buf=5405
cx23885: cx23885_wakeup: [ffff99b40bf79400/31] wakeup reg=9537 buf=9536
This patch loops up to five times on wakeup, marking any buffers
found done.
Since the count register is u16, but the vb2 counter is u32, some modulo
arithmetic is used to accommodate wraparound and ensure current active
buffer is the buffer expected.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This reverts 8b0e195314, because media-tree drivers should use the
API functions to initialize variables of type ktime_t.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In commit 20a63349b1 a new variable ktime_t delay has been added.
We decided to use the API functions to initialize ktime_t variables
within media-tree. Thus variable delay needs to be initialized with
ktime_set() instead of setting it directly.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This issue was reported by a user who downloaded a corrupt saa7164
firmware, then went looking for a valid xc5000 firmware to fix the
error displayed...but the device in question has no xc5000, thus after
much effort, the wild goose chase eventually led to a support call.
The xc5000 has nothing to do with saa7164 (as far as I can tell),
so replace the string with saa7164 as well as give a meaningful
hint on the firmware mismatch.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kconfig Help statements are two-spaced after a single tab.
The incorrect spacing breaks menuconfig on older kernels.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the manual validity checks for the GPIO with the
gpio_is_valid().
In vip_gpio_reserve(), Error checking for gpio pin is not correct.
If pwr_pin = -1, It will return 0. This should be return an error.
In sta2x11_vip_init_one(), Error checking for gpio 'reset_pin'
is unnecessary. Because vip_gpio_reserve() is also checking for
valid gpio pin. So removed extra error checking for gpio 'reset_pin'.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Interrupt behavior shows that some time the frame end and frame start of
next frame is unstable and can range from several to hundreds of
micro-sec. In the case of ~10us, isr may not clear next sof interrupt
status in single handling, which prevents new interrupts from coming.
Fix this by handling all pending IRQs before exiting isr, so any abnormal
behavior results from very short interrupt status changes is protected.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Andy Yeh <andy.yeh@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver depends on sony-laptop driver, but this is available
only for x86. So, add a stub function, in order to allow building
it on non-x86 too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This was left over from the conversion to VB2, where the call was
getting invoked both in buffer_queue and start_streaming, which
was intermittently causing invalid opcodes on the VBI RISC queue.
This change effectively mirrors the exact same change Hans Verkuil
made in cx88-video.c in commit 389208e117 ("[media] cx88:
remove leftover start_video_dma() call").
Thanks to Daniel Glöckner for spotting the actual bug after I spent
several days trying to chase down the issue.
Fixes: 389208e117 ("[media] cx88: remove leftover start_video_dma() call")
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Thanks-to: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The method dvb_frontend_ops::get_frontend_algo() is defined as
returning an 'enum dvbfe_algo', but the implementation in this
driver returns an 'int'.
Fix this by returning 'enum dvbfe_algo' on drivers.
[mchehab+samsung@kernel.org: merge similar patches and patch
ddbridge-mci.c the same way]
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit ee93340e98 ("media: ngene: deduplicate I2C adapter evaluation")
added a helper to evaluate the I2C adapter to be used for demod/tuner
attachment based on the given ngene_channel, and that helper is used in
many attach functions to initialise the i2c_adapter variable. However,
for some reason in tuner_attach_stv6110() and demod_attach_stv0900(), the
adapter evaluation wasn't removed as in all other functions. Fix (or
finalize, even) the helper use by cleaning up the superfluous I2C adapter
evaluation leftover in these two functions.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As pointed by ktest:
>> drivers/media//pci/pt1/pt1.c:1433:5: warning: "CONFIG_PM_SLEEP" is not defined, evaluates to 0 [-Wundef]
#if CONFIG_PM_SLEEP
^~~~~~~~~~~~~~~
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by smatch:
drivers/media/pci/pt1/pt1.c:213 config_demod() error: strncmp() '"tc90522sat"' too small (11 vs 20)
Use the same strncmp() syntax as pt1_init_frontends() does.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As described in Document/timers/timers-howto.txt,
hrtimer-based delay should be used for small sleeps.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Without this patch, re-loading of the module was required after resume.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
earth-pt1 was a monolithic module and included demod/tuner drivers.
This patch removes those FE parts and attach demod/tuner i2c drivers.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When capturing at yuv410p, sg_next was called too many times when chroma is
false, eventually returning NULL. This patch does fix this for my hardware.
Signed-off-by: Samuel Williams <sam8641@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Such check is already there at the routine. So, no need to
repeat it outside.
Cc: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Three really tiny minors in this single commit which all on their own
would just clutter up the commit history unnecessarily:
* ddbridge-regs.h is lacking an include guard. Add it.
* Fix an unnecessary NULL initialisation in ddbridge-ci. The declaration
of the ci struct ptr is immediately followed by kzalloc().
* Clarify that the CXD2099AR is a Sony device in the cxd2099 driver at a
few places including Kconfig.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert the driver to allow its usage with the new I2C
binding way.
Please notice that this patch doesn't convert the
callers to bind to it using the new way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set DDBRIDGE_VERSION in ddbridge.h to 0.9.33-integrated to reflect the
updated driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add needed logic into dvb_input_attach(), ddb_port_probe() and
ddb_ports_init() to initialize and support these new cards.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add PCI IDs and ddb_info for the new MCI-based MaxSX8 cards. Also add
needed defines so the cards can be hooked up into ddbridge's probe and
attach handling.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Implement frontend attachment as ddb_fe_attach_mci() into the
ddbridge-max module. The MaxSX8 MCI cards are part of the Max card series
and make use of the LNB controller driven by the already existing lnb
functionality, so here's where this code belongs to.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This adds initial support for the new MCI-based (micro-code interface)
DD cards, with the first one being the MaxSX8 eight-tuner DVB-S/S2/S2X
PCIe card. The MCI is basically a generalized interface implemented in
the card's FPGA firmware and usable for all kind of cards, without the
need to implement any demod/tuner drivers as this interface "hides" any
I2C interface to the actual ICs, in other words any required driver is
implemented in the card firmware.
At this stage, the MCI interface is quite rudimentary with things like
signal statistics reporting missing, but is already working to serve
DVB streams to DVB applications. Missing functionality will be enabled
over time.
This implements only the ddbridge-mci sub-object and hooks it up to the
Makefile so the object gets build. The upcoming commits hook this module
into all other ddbridge parts where required, including device IDs etc.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The Octopus V3 and Octopus Mini devices support set up of a dummy tuner
mode on port 0 that will deliver a continuous data stream of 125MBytes
per second while raising IRQs and filling the DMA buffers, which comes
handy for some stress, PCIe link and IRQ handling testing. The dummy
frontend is registered using dvb_dummy_fe's QAM dummy frontend. Set
ddbridge.dummy_tuner to 1 to enable this on the supported cards.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the number of DMA buffers and their size configurable using module
parameters. Being able to set these to a higher number might help on
busy systems when handling overall high data rates without having to
edit the driver sources and recompile things.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, /sys/class/ddbridgeX/devid always reports 0 due to devid not
being set at all. Set the devid field alongside while storing all other
hardware ID data.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A 188 byte gap has to be left between the writer and the consumer. This
requires 2*188 bytes available to be able to write to the output buffers.
So, change ddb_output_free() to report free bytes according to this rule.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure to save IRQ states before taking the dma lock, as already done
in it's input_work() counterpart.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Improve IRQ handling in the separated MSG/I2C and IO/TSDATA handlers by
applying a mask for recognized bits immediately upon reading the IRQ mask
from the hardware, so only the bits/IRQs that actually were set will be
acked.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, each IRQ requires one IRQ_HANDLE() line to call each IRQ
handler that was set up. Add a IRQ_HANDLE_NIBBLE() and IRQ_HANDLE_BYTE()
macro to call all handlers in blocks of four (_NIBBLE) or eight (_BYTE)
handlers at a time, to make this construct more compact.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce the ddb_irq_set() helper function (along with a matching
prototype in ddbridge.h) to improve the set up of the IRQ handlers
and handler_data, and rework storing this data into the ddb_link
using a new ddb_irq struct. This also does the necessary rework
of affected variables. And while at it, always do queue_work in
input_handler() as there's not much of a difference to directly
calling input_work if there's no ptr at input->redi, or queueing
this call.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of trying to manage IRQ numbers on itself, utilise the
pci_irq_vector() function to do this, which will take care of correct IRQ
numbering for MSI and non-MSI IRQs. While at it, request and enable MSI-X
interrupts for hardware (boards and cards) that support this.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Introduce the ddb_msi_exit() helper to be used for cleaning up previously
allocated MSI IRQ vectors. Deduplicates code and makes things look
cleaner as for all cleanup work the CONFIG_PCI_MSI ifdeffery is only
needed in the helper now. Also, replace the call to the deprecated
pci_disable_msi() function with pci_free_irq_vectors().
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the ddbridge module initialisation and cleanup code to ddbridge-core
and set up the ddb_wq workqueue there, and create and destroy the ddb
device class there aswell. Due to this, the prototypes for ddb_wq,
ddb_class_create() and ddb_class_destroy() aren't required in ddbridge.h
anymore, so remove them. Also, declare ddb_wq and the ddb_class_*()
functions static.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Besides the 'msi' module option, all options are used from within
ddbridge-core only, so move them over from ddbridge-main, and declare the
associated variables static. Since the prototypes in ddbridge.h aren't
necessary anymore now, remove them. As a side effect, this has the benefit
of aligning things more with the dddvb upstream.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Despite depending on ACPI, this driver builds fine on non-x86
archtecture with COMPILE_TEST, as it doesn't depend on
ACPI-specific functions/structs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver doesn't use any weird API. So, allow building it
with COMPILE_TEST.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
From now on, I'll start using my @kernel.org as my development e-mail.
As such, let's remove the entries that point to the old
mchehab@s-opensource.com at MAINTAINERS file.
For the files written with a copyright with mchehab@s-opensource,
let's keep Samsung on their names, using mchehab+samsung@kernel.org,
in order to keep pointing to my employer, with sponsors the work.
For the files written before I join Samsung (on July, 4 2013),
let's just use mchehab@kernel.org.
For bug reports, we can simply point to just kernel.org, as
this will reach my mchehab+samsung inbox anyway.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Brian Warner <brian.warner@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The HVR 1300 has a Z8F0811 IR device, which can do both IR transmit
and receive. The transmit part was not probed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check for a valid ptr in ddb_io->dma isn't really necessary since only
devices that do data transport using DMA are supported by the driver, and
all previous initialisation code (through input_init(), output_init() and
dma_init(), has_dma is always true as it's set in ddb_probe() during
driver load) guarantees the ptr is set.
As a side effect, this silences these sparse warnings (albeit them being
false positives as ddb_io->dma won't change in these functions so the
condition always equals to the same result):
drivers/media/pci/ddbridge/ddbridge-core.c:495:9: warning: context imbalance in 'ddb_output_start' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:510:9: warning: context imbalance in 'ddb_output_stop' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:525:9: warning: context imbalance in 'ddb_input_stop' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:560:9: warning: context imbalance in 'ddb_input_start' - different lock contexts for basic block
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/pci/mantis/mantis_uart.c:105 mantis_uart_work() warn: this loop depends on readl() succeeding
If something goes wrong at readl(), the logic will stay there
inside an IRQ code forever. This is not the nicest thing to
do :-)
So, add a timeout there, preventing staying inside the IRQ
for more than 10ms.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the logic there to avoid casting, solving this warning:
drivers/media/pci/saa7134/saa7134-alsa.c:276 saa7134_alsa_dma_init() warn: argument 3 to %08lx specifier is cast from pointer
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using an ancillary function to avoid duplicating
a small portion of code that copies data either to kernelspace
or between userspace-kernelspace, duplicate the code,
as it prevents static analyzers to complain about it:
drivers/media/pci/solo6x10/solo6x10-g723.c:260:46: warning: cast removes address space of expression
The hole idea of using __user is to make sure that the code is
doing the right thing with address space, so there's no
sense on use casting.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, the code produces those false-positives:
drivers/media/pci/saa7134/saa7134-input.c:203 get_key_msi_tvanywhere_plus() error: uninitialized symbol 'b'.
drivers/media/pci/saa7134/saa7134-input.c:251 get_key_kworld_pc150u() error: uninitialized symbol 'b'.
drivers/media/pci/saa7134/saa7134-input.c:275 get_key_purpletv() error: uninitialized symbol 'b'.
Improve the error handling code, making it to look like our
coding style.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/pci/ivtv/ivtvfb.c:349 ivtvfb_prep_frame() warn: argument 3 to %08lx specifier is cast from pointer
drivers/media/pci/ivtv/ivtvfb.c:360 ivtvfb_prep_frame() warn: argument 3 to %08lx specifier is cast from pointer
drivers/media/pci/ivtv/ivtvfb.c:363 ivtvfb_prep_frame() warn: argument 4 to %08lx specifier is cast from pointer
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic with gets a p2m_id is more complex than needed,
causing false positives with static analyzers:
drivers/media/pci/solo6x10/solo6x10-p2m.c:81 solo_p2m_dma_desc() error: buffer overflow 'solo_dev->p2m_dev' 4 <= s32max
Make it simpler and use unsigned int.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling logic at get_key_pv951() is a little bit
akward, with produces this false positive warning:
drivers/media/pci/bt8xx/bttv-input.c:344 get_key_pv951() error: uninitialized symbol 'b'.
Do a cleanup. As a side effect, it also improves its coding
style.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The newly added pdev variable is only used in an #ifdef, causing a
build warning without CONFIG_PCI_MSI, unless we move the declaration
inside the same #ifdef:
drivers/media/pci/ngene/ngene-core.c: In function 'ngene_start':
drivers/media/pci/ngene/ngene-core.c:1328:17: error: unused variable 'pdev' [-Werror=unused-variable]
Fixes: 6795bf6264 ("media: ngene: convert kernellog printing from printk() to dev_*() macros")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When loading the budget_av driver for ie. a KNC1 DVB-C TDA10024 card,
which makes use of the ttpci eeprom check functionality (that always
fails on these cards, but that's no issue at all), this is printed
to the kernel log:
[ 10.497333] saa7146 (0): dma buffer size 192512
[ 10.497335] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
[ 10.545007] adapter failed MAC signature check
[ 10.545009] encoded MAC from EEPROM was
[ 10.545010] ff:
[ 10.545011] ff:
[ 10.545011] ff:
...
[ 10.545021] ff
[ 10.832422] budget_av: KNC1-4: MAC addr = 00:09:d6:6d:b3:be
with the 'ff' being repeated for a total of 20 times. Improve that by
using the %*phC format specifier instead dprintk()'ing every byte of the
encoded MAC separately. This obsoletes the int i, and the kernel log
looks cleaner:
[ 3234.383153] saa7146 (0): dma buffer size 192512
[ 3234.383154] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
[ 3234.428745] adapter failed MAC signature check
[ 3234.428747] encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
[ 3234.728194] budget_av: KNC1-0: MAC addr = 00:09:d6:6d:b3:be
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.
The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.
In addition, this is specifically meant for tuners only since they draw the most
current.
This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.
This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.
Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Like in ddbridge, get rid of all duplicated I2C client handling constructs
and rather make use of the newly added dvb_module_*() helpers. Makes
things more clean and removes the (cosmetic) need for some variables.
The check on a valid ptr on ci->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of keeping duplicated I2C client handling construct, make use of
the newly introduced dvb_module_*() helpers. This not only keeps things
way cleaner and removes the need for duplicated I2C client attach code,
but even allows to get rid of some variables that won't help in making
things look cleaner anymore.
The check on a valid ptr on port->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Hauppauge produced a revision of ImpactVCBe using an 888,
with a 25MHz crystal, instead of using the default third
overtone 50Mhz crystal. This overrides that frequency so
that the cx25840 is properly configured. Without the proper
crystal setup the cx25840 cannot load the firmware or
decode video.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently clk_freq is ignored entirely, because the cx235840 driver
configures the xtal at the chip defaults. This is an issue if a
board is produced with a non-default frequency crystal. If clk_freq
is not zero the cx25840 will attempt to use the setting provided,
or fall back to defaults otherwise.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Proper cx2388x chip type is detected in cx25840 probe, the clock
rate is untouched however in probe. The cx25840 only checks for
non default clock values for 888 and provides custom settings for
25MHz 888. This change ensures that cx23888 chips with default 50MHz
crystals will not get configured as if they have 25MHz crystals. A
cx23887 board will continue to be configured for 25MHz crystal as
there is no custom clock support included for it.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The GPIO settings for quadHD boards are wrong. Fix them.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A possible hardware bug was discovered when using CA addon hardware
attached to the ngene hardware, in that the TS input buffer much likely
will shift and thus become unaligned to 188 byte blocks (a full TS frame)
when things like CA module initialisation (which happens via differing
communication paths) take place. This causes the TS NULL removal in
tsin_exchange() to fail to detect this previously inserted data and thus
causes userspace applications to receive data they didn't sent beforehand
and ultimately cause troubles.
On driver load with an inserted CAM, buffers are fine at first (note that
the driver has to keep the communication running from/to the card by
inserting TS NULL frames, this is done in tsout_exchange() via
FillTSBuffer() - that data is simply sent back by the hardware):
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 47 1f ff 10 6f 6f .... 47 1f ff 10 6f 6f .... 47
After a few seconds, the CA module is recognised and initialised, which is
signalled by
dvb_ca_en50221: dvb_ca adapter X: DVB CAM detected and initialised successfully
This is where the first shift happens (this is always four bytes), buffer
becomes like this:
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 6f 6f 6f 6f 47 1f .... 6f 6f 6f 6f 47 1f .... 6f
Next, VDR, TVHeadend or any other CI aware application is started, buffers
will shift by even more bytes. It is believed this is due to the hardware
not handling control and data bytes properly distinct, and control data
having an influence on the actual data stream, which we cannot properly
detect at the driver level.
Workaround this hardware quirk by adding a detection for the TS sync byte
0x47 before each TS frame copy, scan for a new SYNC byte and a TS NULL
packet if buffers become unaligned, take note of that offset and apply
that when copying data to the DVB ring buffers. The last <188 bytes from
the hardware buffers are stored in a temp buffer (tsin_buffer), for which
the remainder will be in the beginning of the next hardware buffer (next
iteration of tsin_exchange()). That remainder will be appended to the
temp buffer and finally sent to the DVB ring buffer. The resulting TS
stream is perfectly fine, and the TS NULL packets inserted by the driver
which are sent back are properly removed. The resulting offset is being
clamped to 188 byte segments (one TS packet). Though this can result in
a repeated TS packet if the overall offset grows beyond this (and it
will grow only on CA initialisation), this is still way better than
unaligned TS frames and data sent to userspace that just isn't supposed
to be there.
This compensation can be toggled by the ci_tsfix modparam, which defaults
to 1 (enabled). In the case of problems, this can be turned off by setting
the parameter to 0 to restore the old behaviour.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the copy logic that will skip previously inserted TS NULL frames when
moving data to the DVB ring buffers into an own function. This is done to
not duplicate code all over the place with the following TS offset shift
fixup patch.
While we're touching this part of the code, get rid of the DEBUG_CI_XFER
debug-ifdeffery. This could be toggleable either by a Kconfig or a module
param, but in the end this will accidentally be enabled and cause lots
of kernel log messages, and such devel debug shouldn't be there anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Report I2C_FUNC_I2C in .functionality() as well. The I2C interface can
handle this fine and even is required for all I2C client drivers that
utilise the regmap API which are used from within the ngene driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the poll callback for the dvbdev_ci file ops. The ts_poll()
function queries the DVB ring buffers for available data and space, and
reports this as appropriate. Also, set the dvb_device readers, writers
and users to proper values (one reader, one writer, two users).
This fixes the raw CI TS transport in conjunction with TVheadend's
DDCI functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When probing the I2C busses in cineS2_probe(), it's no error when there's
no hardware connected to the probed expansion connector, so print this
informal message with info severity.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, if there's no CXD2099AR attached to any expansion connector of
the ngene hardware, it will complain with this on every module load:
cxd2099 1-0040: No CXD2099AR detected at 0x40
cxd2099: probe of 1-0040 failed with error -5
ngene 0000:02:00.0: CXD2099AR attach failed
This happens due to the logic assuming such hardware is always there and
blindly tries to attach the cxd2099 I2C driver. Rather add a probe
function (in ngene-cards.c with a prototype in ngene.h) to check for
the existence of such hardware before probing, and don't try further if
no CXD2099 was found.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C adapter evaluation (based on chan->number) is duplicated at
several places (tuner_attach_() functions, demod_attach_stv0900() and
cineS2_probe()). Clean this up by wrapping that construct in a separate
function which all users of that can pass the ngene_channel pointer and
get the correct I2C adapter from.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the STV0910/STV6111/LNBH25 based DuoFlex S2 V4 DVB-S2
addon modules by recognizing them from their XO2 type value and using
the auxiliary stv0910, stv6111 and lnbh25 driver to form a complete
DVB frontend.
This also adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the STV0910,
STV6111 and LNBH25 demod/tuner/LNB-IC drivers to Kconfig.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recognize (probe) and support (attach) all Sony CXD28xx based DuoFlex
addon modules/cards, namely the DuoFlex CT2 (CXD2837), ISDB-T (CXD2838),
C2T2 (CXD2843) and C2T2I (CXD2854). Since all these modules are equipped
with a MachXO2 interface, that support is required for the hardware to
work. This functionality utilises the auxiliary cxd2841er and tda18212
drivers.
This also adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the CXD2841ER
demod driver to Kconfig. The __maybe_unused annotation can now be removed
from the xo2names array.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Detect and initialise modules equipped with XO2 interfaces (Lattice
MachXO2). This requires a few more I2C transfer functions which this adds
as well. Defines for the different possible (available) module types are
added to ngene.h. The support for the actual tuners contained on these
addon modules is kept separate from this commit and is being added with
the next commits.
The xo2names array is temporarily marked __maybe_unused to silence a
corresponding compiler warning at this stage.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for STV0367+TDA18212 based DuoFlex CT addon modules. For this,
add a demod probe function and all necessary demod/tuner attach functions
which use existing auxiliary drivers (stv0367 and tda18212) to support
this hardware. As tda18212 is an I2C client driver, proper cleanup code
is added to the deregistration sequence in ngene-core. To not cause use-
after-free situations when there's a CXD2099 I2C client connected, which
is rather freed in ngene-core.c:cxd_detach(), add i2c_client_fe to struct
ngene_channel to keep track if the i2c_client was allocated by a frontend
driver, rather than the CI code paths. Also move the I2C access functions
to the top of the file and add the required read_regs() function for the
tda18212 ping to work.
This adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the STV0367 demod
driver and TDA18212 tuner driver to Kconfig aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make it more clear which demod_type is used for which hardware by having
defines for the possible demod_type values. With that, change the
demod_type evaluation in tuner_attach_probe() to a switch-case instead
of an if() for each possible value.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert all printk() and pr_*() kernel log printing to rather use the
dev_*() macros. Not only is it discouraged to use printk() (checkpatch
even complains about that), but also this helps identifying the exact PCI
device for any printed event, and it makes almost all printing shorter
in terms of code style since there's no need to use KERN_* DEVICE_NAME
any more (dev_*() will take care of this).
Since the dprintk macro define isn't used anymore, remove it.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two more device IDs for cards supported by the ngene driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the TODO file, this driver only landed in staging because of
the way device nodes and data transfers are handled. Besides that this way
(use of secX devices) has become sort of standard to date (ie. VDR
supports this literally since ages via the ddci plugin, TVHeadend received
this functionality lately, and minisatip being currently worked on
regarding this), most importantly this I2C client only driver isn't even
responsible for setting up device nodes, not for handling data
transfer and so on, but only serves as interface for the dvb_ca_en50221
subsystem, just like every other DVB card out in the wild, with hard-wired
or such flexible CA interfaces. And, it would even work with cards having
the cxd2099 controller hard-wired.
Also, this driver received quite some love and even is a proper I2C client
driver by now. So, as this driver acts as a EN50221 frontend device, move
it to dvb-frontends. There is no need to keep it buried in staging.
This commit also updates all affected Kconfig and Makefile's, and adds
MEDIA_AUTOSELECT depends to ddbridge and ngene.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Deduplicate the checks for a valid ptr in port->en, and also handle the
default case to also catch eventually yet unsupported CI hardware.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Thoses files are unused since commit b3b961448f ("V4L/DVB (13795): [Mantis/Hopper] Code overhaul, add Hopper devices into the PCI ID list")
8 year after, we could remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new QuadHD digital only PCIe boards to driver list.
Differentiate them from 888 digital/analog QuadHD models.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new PCIe DVB-S/S2.
A single port Hauppauge HVR-5525
cx23885 + a8293 + m88rs6000t
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add ID of new card revision to driver list
Analog PAL/NTSC capture.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a typo at the several s5h14*.h headers: continuous were
spelled incorrectly.
Fix it with this script:
for i in $(git grep -l S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK); do
sed s,S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,g -i $i
done
for i in $(git grep -l -i continous drivers/media); do sed s,CONTINOUS,CONTINUOUS,g -i $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
ivtv-alsa-mixer functions was introduced in commit 269c11fbac
("[media] ivtv, ivtv-alsa: Add initial ivtv-alsa interface driver for ivtv")
But according to commit message, ivtv-alsa-mixer.c was already dead code.
5 years after, we should remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: removed forgotten ivtv-alsa-mixer.h include]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cx18-alsa-mixer functions are not used since commit 4cb565cc27
("V4L/DVB: cx18: make it so cx18-alsa-main.c compiles") 9 year later,
let's just remove them.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suffix LL to constant 1000000 in order to give the compiler
complete information about the proper arithmetic to use. Notice
that this constant is used in a context that expects an expression
of type ktime_t (64 bits, signed).
The expression ir->polling * 1000000 is currently being evaluated
using 32-bit arithmetic.
Addresses-Coverity-ID: 1392628 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1392630 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently an out of range dev->nr is detected by just reporting the
issue and later on an out-of-bounds read on array card occurs because
of this. Fix this by checking the upper range of dev->nr with the size
of array card (removes the hard coded size), move this check earlier
and also exit with the error -ENOSYS to avoid the later out-of-bounds
array read.
Detected by CoverityScan, CID#711191 ("Out-of-bounds-read")
Fixes: commit 02b20b0b4c ("V4L/DVB (12730): Add conexant cx25821 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: %ld -> %zd]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we have support for a buffer counter and for
error flags, update them at DMX_DQBUF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is to avoid pending interrupts to be handled during
stream off, in which case, the ready buffer will be removed
from buffer list, thus not all buffers can be returned to VB2
as expected. Disable CIO2 irq at cio2_hw_exit() so no new
interrupts are generated.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
With "pages" initialized to vb length + 1 pages, the condition
check if(!pages--) will break at one more page than intended,
this can result in out-of-bound access to b->lop[i][j] when setting
the last dummy page.
Fixes: c7cbef1fdb ("media: intel-ipu3: cio2: fix a crash with out-of-bounds access")
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Cao Bing Bu <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My earlier patch missed two functions, these must be __maybe_unused
as well:
drivers/media/pci/intel/ipu3/ipu3-cio2.c:1867:12: error: 'cio2_runtime_resume' defined but not used [-Werror=unused-function]
drivers/media/pci/intel/ipu3/ipu3-cio2.c:1849:12: error: 'cio2_runtime_suspend' defined but not used [-Werror=unused-function]
Fixes: 2086dd3570 ("media: intel-ipu3: cio2: mark PM functions as __maybe_unused")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cobalt sound driver has a dependency on ALSA, but not
on the PCM helper code, so this can lead to an extremely
rare link error in randconfig builds:
ERROR: "snd_pcm_period_elapsed" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "_snd_pcm_stream_lock_irqsave" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_hw_constraint_integer" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_set_ops" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_stream_unlock_irqrestore" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_lib_ioctl" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_new" [drivers/media/pci/cobalt/cobalt.ko] undefined!
The other audio drivers select 'SND_PCM' for this, so let's
do the same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cio2 driver should release buffer with QUEUED state
when start_stream op failed, wrong buffer state will
cause vb2 core throw a warning.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Cao Bing Bu <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When dmabuf is used for BLOB type frame, the frame
buffers allocated by gralloc will hold more pages
than the valid frame data due to height alignment.
In this case, the page numbers in sg list could exceed the
FBPT upper limit value - max_lops(8)*1024 to cause crash.
Limit the LOP access to the valid data length
to avoid FBPT sub-entries overflow.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Cao Bing Bu <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Daniel Scheller