When a HP ProLiant DL980 G7 Server boots a regular kernel,
there will be intermittent lost interrupts which could
result in a hang or (in extreme cases) data loss.
The reason is that this system only supports x2apic physical
mode, while the kernel boots with a logical-cluster default
setting.
This bug can be worked around by specifying the "x2apic_phys" or
"nox2apic" boot option, but we want to handle this system
without requiring manual workarounds.
The BIOS sets ACPI_FADT_APIC_PHYSICAL in FADT table.
As all apicids are smaller than 255, BIOS need to pass the
control to the OS with xapic mode, according to x2apic-spec,
chapter 2.9.
Current code handle x2apic when BIOS pass with xapic mode
enabled:
When user specifies x2apic_phys, or FADT indicates PHYSICAL:
1. During madt oem check, apic driver is set with xapic logical
or xapic phys driver at first.
2. enable_IR_x2apic() will enable x2apic_mode.
3. if user specifies x2apic_phys on the boot line, x2apic_phys_probe()
will install the correct x2apic phys driver and use x2apic phys mode.
Otherwise it will skip the driver will let x2apic_cluster_probe to
take over to install x2apic cluster driver (wrong one) even though FADT
indicates PHYSICAL, because x2apic_phys_probe does not check
FADT PHYSICAL.
Add checking x2apic_fadt_phys in x2apic_phys_probe() to fix the
problem.
Signed-off-by: Stoney Wang <song-bo.wang@hp.com>
[ updated the changelog and simplified the code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1360263182-16226-1-git-send-email-yinghai@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since there are only two locations where cpu_mask_to_apicid() is
called from, remove the operation and use only
cpu_mask_to_apicid_and() instead.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Suggested-and-acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20120614074935.GE3383@dhcp-26-207.brq.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If the HW implements round-robin interrupt delivery, this
enables multiple cpu's (which are part of the user specified
interrupt smp_affinity mask and belong to the same x2apic
cluster) to service the interrupt.
Also if the platform supports Power Aware Interrupt Routing,
then this enables the interrupt to be routed to an idle cpu or a
busy cpu depending on the perf/power bias tunable.
We are now grouping all the cpu's in a cluster to one vector
domain. So that will limit the total number of interrupt sources
handled by Linux. Previously we support "cpu-count *
available-vectors-per-cpu" interrupt sources but this will now
reduce to "cpu-count/16 * available-vectors-per-cpu".
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: yinghai@kernel.org
Cc: gorcunov@openvz.org
Cc: agordeev@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337644682-19854-2-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We know both register and value for eoi beforehand,
so there's no need to check it and no need to do math
to calculate the msr. Saves instructions/branches
on each EOI when using x2apic.
I looked at the objdump output to verify that the
generated code looks right and actually is shorter.
The real improvemements will be on the KVM guest side
though, those come in a later patch.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: gleb@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/e019d1a125316f10d3e3a4b2f6bda41473f4fb72.1337184153.git.mst@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add eoi_write callback so that kvm can override
eoi accesses without touching the rest of the apic.
As a side-effect, this will enable a micro-optimization
for apics using msr.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: gleb@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/0df425d746c49ac2ecc405174df87752869629d2.1337184153.git.mst@redhat.com
[ tidied it up a bit ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide systems that do not support x2apic cluster mode
a mechanism to select x2apic physical mode using the
FADT FORCE_APIC_PHYSICAL_DESTINATION_MODE bit.
Changes from v1: (based on Suresh's comments)
- removed #ifdef CONFIG_ACPI
- removed #include <linux/acpi.h>
Signed-off-by: Greg Pearson <greg.pearson@hp.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1335313436-32020-1-git-send-email-greg.pearson@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As suggested by Suresh Siddha and Yinghai Lu:
For x2apic pre-enabled systems, apic driver is set already early
through early_acpi_boot_init()/early_acpi_process_madt()/
acpi_parse_madt()/default_acpi_madt_oem_check() path so that
apic_id_valid() checking will be sufficient during MADT and SRAT
parsing.
For non-x2apic pre-enabled systems, all apic ids should be less
than 255.
This allows us to substitute the checks in
arch/x86/kernel/acpi/boot.c::acpi_parse_x2apic() and
arch/x86/mm/srat.c::acpi_numa_x2apic_affinity_init() with
apic->apic_id_valid().
In addition we can avoid feigning the x2apic cpu feature in the
NumaChip apic code.
The following apic drivers have separate apic_id_valid()
functions which will accept x2apic type IDs :
x2apic_phys
x2apic_cluster
x2apic_uv_x
apic_numachip
Signed-off-by: Steffen Persvold <sp@numascale.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Daniel J Blueman <daniel@numascale-asia.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1331925935-13372-1-git-send-email-sp@numascale.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move APIC ID validity check into platform APIC code, so it can
be overridden when needed. For NumaChip systems, always trust
MADT, as it's constructed with high APIC IDs.
Behaviour verifies on standard x86 systems and on NumaChip
systems with this, and compile-tested with allyesconfig.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Reviewed-by: Steffen Persvold <sp@numascale.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1331709454-27966-1-git-send-email-daniel@numascale-asia.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This will pave the way for each apic driver to be self-contained
and eliminate the need for apic_probe[].
Order in which apic drivers are listed in the .apicdrivers
section is important, as this determines the apic probe order.
And this is enforced by the ordering of apic driver files in the
Makefile and the macros apic_driver()/apic_drivers().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: steiner@sgi.com
Cc: gorcunov@openvz.org
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110521005526.068775085@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the unused probe routine in the apic driver to finalize the
apic model selection. This cleans up the
default_setup_apic_routing() and this probe routine in future
can also be used for doing any apic model specific
initialisation.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: steiner@sgi.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110519234637.247458931@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
apic->apicid_to_node() is 32bit specific apic operation which
determines NUMA node for a CPU. Depending on the APIC
implementation, it can be easier to determine NUMA node from
either physical or logical apicid. Currently,
->apicid_to_node() takes @logical_apicid and calls
hard_smp_processor_id() if the physical apicid is needed.
This prevents NUMA mapping from being queried from a different
CPU, which in turn makes it impossible to initialize NUMA
mapping before SMP bringup.
This patch replaces apic->apicid_to_node() with
->x86_32_numa_cpu_node() which takes @cpu, from which both
logical and physical apicids can easily be determined. While at
it, drop duplicate implementations from bigsmp_32 and summit_32,
and use the default one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Pekka Enberg <penberg@kernel.org>
Cc: eric.dumazet@gmail.com
Cc: yinghai@kernel.org
Cc: brgerst@gmail.com
Cc: gorcunov@gmail.com
Cc: shaohui.zheng@intel.com
Cc: rientjes@google.com
LKML-Reference: <1295789862-25482-13-git-send-email-tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After the previous patch, apic->cpu_to_logical_apicid() is no
longer used. Kill it.
For apic types with custom cpu_to_logical_apicid() which is also
used for other purposes, remove the function and modify its
users to do the mapping directly.
#ifdef's on CONFIG_SMP in es7000_32 and summit_32 are ignored
during conversion as they are not used for UP kernels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: eric.dumazet@gmail.com
Cc: yinghai@kernel.org
Cc: brgerst@gmail.com
Cc: gorcunov@gmail.com
Cc: penberg@kernel.org
Cc: shaohui.zheng@intel.com
Cc: rientjes@google.com
LKML-Reference: <1295789862-25482-7-git-send-email-tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: optimize APIC IPI related barriers
Uncached MMIO accesses for xapic are inherently serializing and hence
we don't need explicit barriers for xapic IPI paths.
x2apic MSR writes/reads don't have serializing semantics and hence need
a serializing instruction or mfence, to make all the previous memory
stores globally visisble before the x2apic msr write for IPI.
Add x2apic_wrmsr_fence() in flush tlb path to x2apic specific paths.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "steiner@sgi.com" <steiner@sgi.com>
Cc: Nick Piggin <npiggin@suse.de>
LKML-Reference: <1237313814.27006.203.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
- rename apic->wakeup_cpu to apic->wakeup_secondary_cpu, to
make it apparent that this is an SMP-only method
- handle NULL ->wakeup_secondary_cpus to mean the default INIT
wakeup sequence - this allows simplification of the APIC
driver templates.
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
x86_quirks->update_apic() calling looks crazy. so try to remove it:
1. every apic take wakeup_cpu member directly
2. separate es7000_apic to es7000_apic_cluster
3. use uv_wakeup_cpu directly
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If BIOS hands over the control to OS in legacy xapic mode, select
legacy xapic related ops in the early apic probe and shift to x2apic
ops later in the boot sequence, only after enabling x2apic mode.
If BIOS hands over the control in x2apic mode, select x2apic related
ops in the early apic probe.
This fixes the early boot panic, where we were selecting x2apic ops,
while the cpu is still in legacy xapic mode.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/ is getting a bit crowded, and the APIC
drivers are scattered into various different files.
Move them to arch/x86/kernel/apic/*, and also remove
the 'gen' prefix from those which had it.
Also move APIC related functionality: the IO-APIC driver,
the NMI and the IPI code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stoney Wang