Change the dvbsky driver to support gapped clock instead of the current
hack.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TeVii S482 is a PCIe device with two tuners that actually contains two
USB devices. The devices are visible in the lsusb printout.
Bus 006 Device 002: ID 9022:d483 TeVii Technology Ltd.
Bus 007 Device 002: ID 9022:d484 TeVii Technology Ltd.
The device itself works exactly with the same settings as TechnoTrend
TT-connect S2-4600. Firmware for DS3103 demodulator is required:
http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
This patch should be applied on top of the TT S2-4600 patch:
https://patchwork.linuxtv.org/patch/28818/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace all calls to s_mbus_fmt in bridge drivers by calls to the
set_fmt pad op.
Remove the old try/s_mbus_fmt video ops since they are now no longer used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s_mbus_fmt video op is a duplicate of the pad op. Replace all uses
in sub-devices by the set_fmt() pad op.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Running v4l2-compliance on my usbtv stick revealed two failures:
1) Correct handling of CREATE_BUFS in usbtv_queue_setup was missing. Added this.
2) The sequence counter wasn't reset to 0 when starting streaming.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since the first version of this driver, the remote controller
code is disabled, adding an early return inside vp702x_rc_query().
Let's disable the code with #if 0, to remove this warning:
drivers/media/usb/dvb-usb/vp702x.c:268 vp702x_rc_query() info: ignoring unreachable code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/usb/gspca/zc3xx.c:5994 transfer_update() info: ignoring unreachable code.
That happens because there's a return that it is never called,
as the work queue runs an infinite loop, except when the device is
put to sleep or an error happens.
When an error happens, a break statement is enough to go out of
the loop. So, let's remove the goto, as break is the typical
instruction used to end a loop.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/usb/go7007/go7007-driver.c:452 frame_boundary() warn: variable dereferenced before check 'vb' (see line 449)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* patchwork: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
Add support for the new VIDIOC_QUERY_EXT_CTRL ioctl. Since uvc doesn't use
the control framework, support for this ioctl isn't automatic.
This is makes v4l2-compliance happy as well.
[Added blank lines for improved readability]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2-compliance tool expects that if VIDIOC_CROPCAP is defined, then
VIDIOC_G_SELECTION for TGT_CROP_BOUNDS/DEFAULT is also defined (or COMPOSE
in the case of an output device).
In fact, all that a driver has to do to implement cropcap is to support
those two targets since the v4l2 core will implement cropcap and fill in
the pixelaspect to 1/1 by default.
Implementing cropcap is only needed if the pixelaspect isn't square.
So implement g_selection instead of cropcap in uvc to fix the v4l2-compliance
failure.
[Added blank lines for improved readability]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add Leadtek WinFast DTV2000DS Plus device based on Realtek RTL2832U.
I have not tested the remote, but it is the Y04G0051 model.
Signed-off-by: Christian Dale <kernel@techmunk.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ID 1b80:d3a4 Afatech
Simply added the PID (0xd3a4) of this DVB-T USB device to the list of rtl2832u-supported devices. VID (0x1b80) is same as KWORLD2.
Tested and verified to work in amd64 with kernels 3.13.0 and 3.16.0.
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use enum to represent table offsets rather than hard-coding numbers to avoid
problems with the numbers becoming out of sync with the table.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixing a few checkpatch errors of type: space required after that ','
Signed-off-by: Luis de Bethencourt <luis.bg@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no usb_put_dev() on failure paths in usbvision_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change ts2022 driver to ts2020 driver. ts2020 driver supports
both tuner chip models.
That affects TechnoTrend TT-connect S2-4600 DVB-S/S2 device, which
Olli just added.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change ts2022 driver to ts2020 driver as ts2020 driver now supports
both models.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TechnoTrend TT-connect S2-4600 is a USB2.0 DVB-S/S2 tuner using the popular
Montage M88DS3103/M88TS2022 demod/tuner.
The demodulator needs a firmware. Antti posted a firmware when releasing
support for PCTV 461e, available here:
http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare the dw2102 driver for tuner drivers that are implemented as I2C
drivers (such as m88ts2022). The I2C client is stored in to the state
and released at disconnect.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Two separate state structs are defined for different devices inside the
dw2102. Combine them, as both only contain one element.
This will also make it easier to further cleanup the driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Astrometa device has issues with i2c transfers. Lowering the
poll time somehow makes these errors disappear.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All uses of the v4l2_clk API so far only register one clock with a fixed
name. This allows us to get rid of it, which also will make CCF and DT
integration easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit c5036d61e0 ("media: au0828: drop
vbi_buffer_filled() and re-use buffer_filled()") broke video and vbi streaming.
The vb2_buffer struct was copied instead of taking a pointer to it, but
vb2_buffer_done() needs the real object, not a copy, since it is hooking
the buffer into a different list.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return success for FE callback on case we don't have any special
implementation. fc0013 tuner driver calls that callback in order to
switch antenna input, even we don't provide antenna switch.
Returning error caused fc0013 driver given up tuning.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If CONFIG_VIDEO_CX231XX_RC is undefined, then these compiler warnings
are generated:
In file included from drivers/media/usb/cx231xx/cx231xx-cards.c:23:0:
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_release_resources’:
drivers/media/usb/cx231xx/cx231xx.h:982:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_exit(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1158:2: note: in expansion of macro ‘cx231xx_ir_exit’
cx231xx_ir_exit(dev);
^
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_init_dev’:
drivers/media/usb/cx231xx/cx231xx.h:981:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_init(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1351:2: note: in expansion of macro ‘cx231xx_ir_init’
cx231xx_ir_init(dev);
^
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx.h:982:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_exit(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1705:2: note: in expansion of macro ‘cx231xx_ir_exit’
cx231xx_ir_exit(dev);
^
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_disconnect’:
drivers/media/usb/cx231xx/cx231xx.h:982:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_exit(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1754:3: note: in expansion of macro ‘cx231xx_ir_exit’
cx231xx_ir_exit(dev);
^
Fix by using static inlines instead of defines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The available (i.e. not used) buffers are returned by stk1160_clear_queue(),
on the stop_streaming() path. However, this is insufficient and the current
buffer must be released as well. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Olli Salonen