In some test envirenment, there is loopback topology test. We should
handle this during discovery.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling. The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.
Finally, activate the port recovery of the libata error handler for
each port known to the host. This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Originally, libata required the illusion that it could access the sata
control register. Now, however, it can run perfectly well without
them, so remove the dummy routines from libsas which tried to emulate
them (but only ended up causing confusion).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ATAPI check condition needs to be treated the same as a success or
protocol return. The register returns from the PACKET command are all
correctly positioned in the device to host register FIS and so we
should collect them properly. Right at the moment this doesn't matter
because libata sends a request sense always for ATAPI errors, but if
it ever checked the registers, we should have the correct contents
just in case.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To date libsas has only looked at the attached sas address when
determining the formation of wide ports. The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other. Introduce a flag
to select stricter behavior at sas_register_ha() time. The flag can be
dropped once it is known that all libsas users expect the same behavior.
Current drivers just initialize this field to zero and get the
traditional behavior.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fix bug reported by Chuck. And this new version incorporate comments
from Hannes. Please consider to include it into mainline.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Tested-by: Chuck Tuffli <Chuck_Tuffli@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning. Change libsas
to reject commands to domain devices that have already gone away.
[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
permit sync cache commands at module removal]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Tested-by: Haipao Fan <haipao.fan@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some cards (like mvsas) have issue troubles if non-NCQ commands are
mixed with NCQ ones. Fix this by using the libata default NCQ check
routine which waits until all NCQ commands are complete before issuing
a non-NCQ one. The impact to cards (like aic94xx) which don't need
this logic should be minimal
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
REQ_HARDBARRIER is deprecated. Remove spurious uses in the following
users. Please note that other than osdblk, all other uses were
already spurious before deprecation.
* osdblk: osdblk_rq_fn() won't receive any request with
REQ_HARDBARRIER set. Remove the test for it.
* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
anything. Removed.
* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
spurious. Removed.
* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
spurious. Removed.
* scsi_tcq: The ordered tag path wasn't being used anyway. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We have two separate definitions for identical constants with nearly the
same name. One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).
Fix this by eliminating the libsas.h duplicate
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date: Thu Apr 15 09:00:08 2010 +0900
[SCSI] fix locking around blk_abort_request()
Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.
Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_abort_request() expects queue lock to be held by the caller.
Grab it before calling the function.
Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We should not set res to 0 in function sas_ex_discover_dev in order to let
it discover it further when wide port hotplug in .
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hotplug of phys which form wide ports simply does not work at the moment. Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port. This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse. In that case, a new port is formed even if there's a
wide port it should be part of. Fix this by creating two loops over all the
ports: the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.
Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero. The conversion was done under the assumption that
when a request fails residue count wasn't defined. However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.
This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers. While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.
* ide-cd: rq->resid_len cleared on pc success
* mptsas: req->resid_len cleared on success
* sas_expander: rsp/req->resid_len cleared on success
* mpt2sas_transport: req->resid_len cleared on success
* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
advantage of initial full count to simplify code
Boaz Harrosh spotted bug in resid_len initialization. Fixed as
suggested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct
users to accessors. IDE will be converted in a separate patch.
Boaz: spotted incorrect data_len/resid_len conversion in osd.
[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion. This duality creates some
headaches.
First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing. It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count. This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.
Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred. The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all. This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.
This patch adds rq->resid_len which is used only for residual count.
While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.
Boaz : spotted missing conversion in osd
Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape
[ Impact: cleanup residual count handling, report 0 resid by default ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
doc/cdrom: Trvial documentation error, file not present
block_dev: fix kernel-doc in new functions
block: add some comments around the bio read-write flags
block: mark bio_split_pool static
block: Find bio sector offset given idx and offset
block: gendisk integrity wrapper
block: Switch blk_integrity_compare from bdev to gendisk
block: Fix double put in blk_integrity_unregister
block: Introduce integrity data ownership flag
block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
bio.h: Remove unused conditional code
block: remove end_{queued|dequeued}_request()
block: change elevator to use __blk_end_request()
gdrom: change to use __blk_end_request()
memstick: change to use __blk_end_request()
virtio_blk: change to use __blk_end_request()
blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
block: add lld busy state exporting interface
block: Fix blk_start_queueing() to not kick a stopped queue
include blktrace_api.h in headers_install
...
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
[SCSI] iscsi: bidi support for iscsi_tcp
[SCSI] iscsi: bidi support at the generic libiscsi level
[SCSI] iscsi: extended cdb support
[SCSI] zfcp: Fix error handling for blocked unit for send FCP command
[SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
[SCSI] zfcp: fix 31 bit compile warnings
[SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
[SCSI] bsg: remove minor in struct bsg_device
[SCSI] bsg: use better helper list functions
[SCSI] bsg: replace kobject_get with blk_get_queue
[SCSI] bsg: takes a ref to struct device in fops->open
[SCSI] qla1280: remove version check
[SCSI] libsas: fix endianness bug in sas_ata
[SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
[SCSI] aacraid: Do not describe check_reset parameter with its value
[SCSI] aacraid: Fix down_interruptible() to check the return value
[SCSI] sun3_scsi_vme: add MODULE_LICENSE
[SCSI] st: rename flush_write_buffer()
[SCSI] tgt: use KMEM_CACHE macro
[SCSI] initio: fix big endian problems for auto request sense
...
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers. Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->[alt_]check_status(). In fact, no one calls them
for non-SFF drivers anymore. Kill them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly. It gets called only via
ops->qc_fill_rtf() for non-SFF drivers. This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().
This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read(). Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.
As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.
ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.
ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes. As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Provide a facility to use the request_firmware() interface to get a SAS
address from userspace. This can be used by SAS LLDDs that cannot
obtain the address from the host adapter.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We give a very cryptic error if an ATA device is seen on a SAS port
but libsas isn't compiled to include libata to handle them. Add an
extra warning to explain specifically what the problem is.
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Correct one use after free of the sas task
- update the reset required path to move straight to LUN reset
- make the bigger hammer actually reset something instead of just trying
to clear all the tasks.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Once the phy reset is plumbed in properly, SATA error handling fails
nastily because we change the port attached_sas_address using the WWN
field of the IDENTIFY message. This is a nice thing to do in theory,
but it really destroys hotplug because any event on the port causes an
automatic mismatch between the sas_address the phy just picked up and
the one we propagate into the port. However ugly they are, we have to
stick with the sas addresses made up by the phys and expanders.
Also does a few cosmetic changes to the way port printing is done to
make it clearer how a port is formed.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This is needed by the to be added I_T reset function in aic94xx. It
needs to know the local phy so it can send a link or hard reset along
the path.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current sas_scsi_clear_queue_lu() is wrongly checking for commands
which match the pointer to the one passed in. It should be checking for
commands which are on the same logical unit as the one passed in. Fix
this by checking target pointer and LUN for equality.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The libsas error handler has two fairly fatal bugs
1. scsi_sas_task_done calls scsi_eh_finish_cmd() too early. This
happens if the task completes after it has been aborted but before
the error handler starts up. Because scsi_eh_finish_cmd()
decrements host_failed and adds the task to the done list, the
error handler start check (host_failed == host_busy) never passes
and the eh never starts.
2. The multiple task completion paths sas_scsi_clear_queue_... all
simply delete the task from the error queue. This causes it to
disappear into the ether, since a command must be placed on the
done queue to be finished off by the error handler. This behaviour
causes the HBA to hang on pending commands.
Fix 1. by moving the SAS_TASK_STATE_ABORTED check to an exit clause at
the top of the routine and calling ->scsi_done() unconditionally (it
is a nop if the timer has fired). This keeps the task in the error
handling queue until the eh starts.
Fix 2. by making sure every task goes through task complete followed
by scsi_eh_finish_cmd().
Tested this by firing resets across a disk running a hammer test (now
it actually survives without hanging the system)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
that provided by the block layer
ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis. However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary. Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length. The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.
Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary. Note that this aligment only applies to transfers
coming in from user space. However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.
tj: * Adjusting sg after padding is done in block layer. Make libata
set queue alignment correctly for ATAPI devices and drop broken
sg mangling from ata_sg_setup().
* Use request->raw_data_len for ATAPI transfer chunk size.
* Killed qc->raw_nbytes.
* Separated out killing qc->n_iter.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (67 commits)
fix drivers/ata/sata_fsl.c double-decl
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: Merge winbond support
ata_generic: Cenatek support
pata_winbond: error return
pata_serverworks: Fix cable types and cosmetics
pata_mpc52xx: remove un-needed assignment
libata: fix off-by-one in error categorization
ahci: factor out AHCI enabling and enable AHCI before reading CAP
ata_piix: implement SIDPR SCR access
ata_piix: convert to prepare - activate initialization
libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
[libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
pata_legacy: resychronize with upstream changes and resubmit
[libata] pata_legacy: typo fix
[libata] pata_winbond: update for new ->data_xfer hook
pata_pcmcia: convert to new data_xfer prototype
libata annotations and fixes
libata: use dev_driver_string() instead of "libata" in libata-sff.c
ata_piix: kill unused constants and flags
...
Break out the frame processor for STP tasks from aic94xx so they can
be shared by other SAS HBA's
Original patch from Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
LLDs don't need to zero out scsi_cmnd::sense_buffer in queuecommand
since scsi-ml does. This is a preparation of the future changes to
allocate the sense_buffer only when necessary.
Many LLDs zero out the sense_buffer before touching it on the error
case. This patch lets them alone for now because new APIs for them
would be added later on.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: "Salyzyn, Mark" <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
libata used private sg iterator to handle padding sg. Now that sg can
be chained, padding can be handled using standard sg ops. Convert to
chained sg.
* s/qc->__sg/qc->sg/
* s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg
entry. There need to be two extra sg entries. The renaming is also
for future addition of other extra sg entries.
* Padding setup is moved into ata_sg_setup_extra() which is organized
in a way that future addition of other extra sg entries is easy.
* qc->orig_n_elem is unused and removed.
* qc->n_elem now contains the number of sg entries that LLDs should
map. qc->mapped_n_elem is added to carry the original number of
mapped sgs for unmapping.
* The last sg of the original sg list is used to chain to extra sg
list. The original last sg is pointed to by qc->last_sg and the
content is stored in qc->saved_last_sg. It's restored during
ata_sg_clean().
* All sg walking code has been updated. Unnecessary assertions and
checks for conditions the core layer already guarantees are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is bad for two reasons:
1. If they're returned to outside applications, no-one knows what
they mean.
2. Eventually they'll clash with the ever expanding standard error
codes.
The problem error code in question is ETASK. I've replaced this by
ECOMM (communications error on send) a network error code that seems to
most closely relay what ETASK meant.
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All SMP tasks sent through bsg generate messages like:
sas: smp_execute_task: task to dev 500605b000001450 response: 0x0 status 0x81
Three times (because the task gets retried). Firstly, don't retry
either overrun or underrun (the data buffer isn't going to change size)
and secondly, just report the underrun but don't set an error for it.
This is necessary so bsg can report back the residual.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This adds support for host side SMP processing, via a separate
SMP interpreter file.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Annotate sas_queuecommand with locking details, and clean up a few
more sparse warnings about static/non-static declarations.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
sparse complains about the mixing of enums in libsas. Since the
underlying numeric values of both enums are the same, combine them
to get rid of the warning.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The task_struct->pid member is going to be deprecated, so start
using the helpers (task_pid_nr/task_pid_vnr/task_pid_nr_ns) in
the kernel.
The first thing to start with is the pid, printed to dmesg - in
this case we may safely use task_pid_nr(). Besides, printks produce
more (much more) than a half of all the explicit pid usage.
[akpm@linux-foundation.org: git-drm went and changed lots of stuff]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you have the libsas with ATA support, it needs libata to function.
The problem is that if you compile in libsas, you can't build libata
as a module (however, vice versa you can).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In sas_smp_get_phy_events() we never test if the call to
alloc_smp_req(RPEL_REQ_SIZE) succeeds or fails. That means we run
the risk of dereferencing a NULL pointer if it does fail. Far
better to test if we got NULL back and in that case return -ENOMEM
just as we already do for the other memory allocation in that
function.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Eliminate unnecessary PCI dependencies in libsas. It should use generic
DMA and struct device like other subsystems.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_smp_handler crashes when smp utils are used with an aic94xx host
because certain devices (the sas_host itself, specifically) lack rphy
structures. No rphy means no SMP target support, but we shouldn't crash
here.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Not everyone wants libsas automatically to pull in libata. This patch
makes the behaviour configurable, so you can build libsas with or
without ATA support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fixes up the usage in libsas (which are easy to miss, since they're
only in the scsi-misc tree) ... and also corrects the documentation on
the point of what these two function pointers actually return.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for SAS Management Protocol (SMP) passthrough
support via bsg. aic94xx can use this.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
lockdep noticed that with ATA support the port->dev_list_lock was
entangled at irq context, so it now needs to become IRQ safe
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one was noticed by Gilbert Wu of Adaptec:
The libata core actually does the DMA mapping for you, so there has to
be an exception in the device drivers that *don't* do dma mapping for
ATA commands. However, since we've already done this, libsas must now
dma map any ATA commands that it wishes to issue ... and yes, this is a
horrible mess.
Additionally, the test in aic94xx for ATA protocols isn't quite right.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ATA devices need special handling for sas_task_abort. If the ATA command
came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd.
However, internal commands require a bit more work--we need to fill the qc
with the appropriate error status and complete the command, and eventually
post_internal will issue the actual ABORT TASK.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The SATL should connect the scsi_cmnd to the sas_task (despite the presence
of libata) so that requests to abort scsi_cmnds headed to the ATA device
can be processed by the EH and aborted correctly. The abort status should
still be propagated from sas -> ata -> scsi.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When libsas encounters a STP device whose protocol isn't recognized (i.e.
not ATA or ATAPI), we should set the ata_device's class to ATA_DEV_UNKNOWN
instead of ATA_DEV_ATA.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A sas_task sent to an ATAPI devices returns SAM_GOOD if successful.
Therefore, we should treat this the same way we treat ATA commands
that succeed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since the aic94xx sequencer assigns its own NCQ tags to ATA commands, it
no longer makes any sense to copy the sactive field in the STP response
to ata_port->sactive, as that will confuse libata. Also, libata seems
to be capable of managing sactive on its own.
The attached patch gets rid of one of the causes of the BUG messages in
ata_qc_new, and seems to work without problems on an IBM x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds a new field, lldd_task, to ata_queued_cmd so that libata
users such as libsas can associate some data with a qc. The particular
ambition with this patch is to associate a sas_task with a qc; that way,
if libata decides to timeout a command, we can come back (in
sas_ata_post_internal) and abort the sas task.
One question remains: Is it necessary to reset the phy on error, or will
the libata error handler take care of it? (Assuming that one is written,
of course.) This patch, as it is today, works well enough to clean
things up when an ATA device probe attempt fails halfway through the probe,
though I'm not sure this is always the right thing to do.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The sas_ata_qc_issue function was incorrectly written to return error
codes such as -ENOMEM. Since libata OR's qc->err_mask with the
return value, It is necessary to make my code return one of the
AC_ERR_ codes instead. For now, use AC_ERR_SYSTEM because an error
here means that the OS couldn't send the command to the controller.
If anybody has a suggestion for a better AC_ERR_ code to use, please
suggest it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ata_qc_complete and ata_sas_queuecmd require that the port lock be held
when they are called. sas_ata doesn't do this, leading to BUG messages
about qc tags newly allocated qc tags already being in use. This patch
fixes the locking, which should clean up the rest of those messages.
So far I've tested this against an IBM x206m with two SATA disks with no
BUG messages and no other signs of things going wrong, and the machine
finally passed the pounder stress test.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a respin of my earlier patch that migrates the ATA support code
into a separate file. For now, the controversial linking bits have
been removed per James Bottomley's request for a patch that contains
only the migration diffs, which means that libsas continues to require
libata. I intend to address that problem in a separate patch.
This patch is against the aic94xx-sas-2.6 git tree, and it has been
sanity tested on my x206m with Seagate SATA and SAS disks without
uncovering any new problems.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We actually had two problems: the one with the tag (which is fixed by
zeroing the tag before sending the taskfile to the sequencer) but the
other with the fact that we sent our first NCQ command to the device
before the sequencer had been informed of the NCQ tagging
capabilities. I fixed the latter by moving the rphy_add() to the
correct point in the code after the NCQ capabilities are set up.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This replaces a few BUG_ON() statements with the correct failure error
handling. There are still many more to do.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It turns out this is fairly easy to plumb in by recognising the three
command types and copying the CDB. The protocol response path needs to
be amended to cope with SAS_PROTO_RESPONSE.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds SATAII NCQ support to libsas. Both the use_ncq and the
dma_xfer flags in ata_task must be set for NCQ to work correctly on the
Adaptec SAS controller. The rest of the patch adds ATA_FLAG_NCQ to
sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't
crash. Please note that this patch is against the aic94xx-sas git tree,
not scsi-misc. Thanks also to James Bottomley for providing an earlier
version of this patch from which to work.
I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged
into the Adaptec SAS controller. The drive came up with a queue depth
of 31, and I successfully ran an I/O flood test to coerce libata into
sending multiple commands simultaneously. A kernel probe recorded the
maximum tag number that had been seen before and after the flood test;
before the test it was 2 and after it was 30, as I expected.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The prototype of this has changed for the link speed setting patch.
Need to update the SATA use of this.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for SATA over SAS expanders to the previous two
SATA support in libsas patches.
There were a couple of nasty non trivial things to sort out before this
one could be made to work.
Firstly, I'd like to thank Doug Gilbert for diagnosing a problem with
the LSI expanders where the REPORT_SATA_PHY command was returning the
D2H FIS in the wrong order (Although, here, I think I have to blame the
SAS standards which specifies the FIS "shall be returned in little
endian format" and later on "which means resp[24] shall be FIS type"
The latter, of course, implying big endian format). Just to make sure,
I put a check for the D2H FIS type being in the wrong position and
reverse the FIS data if it is.
The second is a problem outlined in Annex G of the SAS standard (again,
a technical point with D2H FIS ... necessitating a phy reset on certain
conditions).
With the patch, I can now see my SATA-1 disk in a cascaded expander
configuration.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hook the scsi_host_template functions in libsas to delegate
functionality to libata when appropriate.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Misc code changes and merge fixes and update for libata->drivers/ata
move
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Well, first of all, I don't want to change so many files either.
What I do:
Adding a new parameter "struct bin_attribute *" in the
.read/.write methods for the sysfs binary attributes.
In fact, only the four lines change in fs/sysfs/bin.c and
include/linux/sysfs.h do the real work.
But I have to update all the files that use binary attributes
to make them compatible with the new .read and .write methods.
I'm not sure if I missed any. :(
Why I do this:
For a sysfs attribute, we can get a pointer pointing to the
struct attribute in the .show/.store method,
while we can't do this for the binary attributes.
I don't know why this is different, but this does make it not
so handy to use the binary attributes as the regular ones.
So I think this patch is reasonable. :)
Who benefits from it:
The patch that exposes ACPI tables in sysfs
requires such an improvement.
All the table binary attributes share the same .read method.
Parameter "struct bin_attribute *" is used to get
the table signature and instance number which are used to
distinguish different ACPI table binary attributes.
Without this parameter, we need to offer different .read methods
for different ACPI table binary attributes.
This is impossible as there are various ACPI tables on different
platforms, and we don't know what they are until they are loaded.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sysfs is now completely out of driver/module lifetime game. After
deletion, a sysfs node doesn't access anything outside sysfs proper,
so there's no reason to hold onto the attribute owners. Note that
often the wrong modules were accounted for as owners leading to
accessing removed modules.
This patch kills now unnecessary attribute->owner. Note that with
this change, userland holding a sysfs node does not prevent the
backing module from being unloaded.
For more info regarding lifetime rule cleanup, please read the
following message.
http://article.gmane.org/gmane.linux.kernel/510293
(tweaked by Greg to not delete the field just yet, to make it easier to
merge things properly.)
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After discussion with andmike and dougg, it seems that the purpose of
eh_device_reset_handler is to issue LU resets, and that
eh_bus_reset_handler would be a more appropriate place for a phy reset.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
libsas: Don't BUG when connecting two expanders via wide port
When a device is connected to an expander, the discovery process goes through
sas_ex_discover_dev to figure out what's attached to the phy. If it is the
case that the phy being discovered happens to be the second phy of a wide link
to an expander, that discover_dev function will incorrectly call
sas_ex_discover_expander, which creates another sas_port and tries to attach the
other sas_phys to the new port, thus triggering a BUG. The correct thing to do is
to check the other ex_phys of the expander to see if there's a sas_port for this
sas_phy, and attach the sas_phy to the existing sas_port.
This is easily triggered if one enables the phys of a wide port between
expanders one by one.
This second version of the patch fixes a small regression in the case where
all the phys show up at once and we accidentally try to attach to a port
that hasn't been created yet.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Set allow_restart=1 for all SAS disks so that they are spun up when needed.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function. It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing. This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop. It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy. This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.
This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.
This patch does not change the semantics of sas_rphy_delete.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently, sas_form_port checks the given asd_sas_phy's sas_phy to see if
there's already a port attached. If so, the SAS addresses of the port and
the phy are compared to determine if we need to detach from the port
because the addresses don't match or if we can stop; the SAS address stored
in the sas_port reflects whatever device _was_ attached to the port/phy, and
the SAS address stored in the sas_port reflects whatever device we just
discovered. As written, the code detaches from the port if the addresses
_do_ match, and prints an error if they do _not_ match. I believe this to
be incorrect, as it seems more logical to keep the port if the addresses
match (i.e. the phy was reset but the device didn't change), and detach it
they do not (i.e. the device changed).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The EH should fall into I_T recovery (and potentially stronger
remedies) if ABORT TASK fails.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Track sas_ha_struct state so that we ignore events that come in while
we're shutting things down.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the phy port locks to use irq spinlocks.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command. By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions. Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.
Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command. This is a hook for libata internal commands to abort.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port. Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we use task collector mode, we can end up destroying the task collector
thread before we release the ports, which is bad if a port release causes
a disk I/O (such as cache flushing).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Every so often, a scsi_cmnd will time out, and the libsas timeout handler
will discover that the scsi_cmnd does not have a sas_task attached to it.
This can happen in two cases: (1) the scsi_cmnd actually made it through
libsas to the HBA and is now going through scsi_done, or (2) the
scsi_cmnd has been held up (host lock, slab alloc, etc) and libsas has
not yet attached a sas_task. In both cases, it is safe to ask SCSI for
more time to process the command via EH_RESET_TIMER; we cannot blindly
return EH_HANDLED because if (2) happens, we could end up calling
scsi_done while another CPU is heading towards sas_queuecommand, which
causes slab corruption when sas_task_done updates the freed scsi_cmnd.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch lets a user arbitrarily enable or disable a phy via sysfs.
Potential applications include shutting down a phy to replace one
lane of wide port, and (more importantly) providing a method for the
libata SATL to control the phy.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On a system with many SAS targets, it appears possible that a scsi_cmnd
can time out without ever making it to the SAS LLDD or at the same time
that a completion is occurring. In both of these cases, telling the
LLDD to abort the sas_task makes no sense because the LLDD won't know
about the sas_task; what we really want to do is to increase the timer.
Note that this involves creating another sas_task bit to indicate
whether or not the task has been sent to the LLDD; I could have
implemented this by slightly redefining SAS_TASK_STATE_PENDING, but
this way seems cleaner.
This second version amends the aic94xx portion to set the
TASK_AT_INITIATOR flag for all sas_tasks that were passed to
lldd_execute_task.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
This patch fixes up sas_expander.c separately because jejb has some
cleanup patches of his own that are a prerequisite.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/pcmcia/ds.c
Fix up merge failures with Linus's head and fix new compile failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
With async scanning, we're now tripping the BUG_ON in
sas_ex_discover_end_dev(), so make the error handling here correct.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch implements a REQ_DEVICE_RESET handler for the aic94xx
driver. Like the earlier REQ_TASK_ABORT patch, this patch defers the
device reset to the Scsi_Host's workqueue, which has the added benefit
of ensuring that the device reset does not happen at the same time
that the abort tmfs are being processed. After the phy reset, the
busted drive should go away and be re-detected later, which is indeed
what I've seen on both a x260 and a x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds an external function, sas_abort_task, to enable LLDDs
to abort sas_tasks. It also adds a work_struct so that the actual
work of aborting a task can be shifted from tasklet context (in the
LLDD) onto the scsi_host's workqueue.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds an EH done queue to sas_ha, converts the error handling
strategy function and the sas_scsi_task_done functions in libsas to use
the scsi_eh_* commands for error'd commands, and adds checks for the
INITIATOR_ABORTED flag so that we do the right thing if a sas_task has
been aborted by the initiator.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updating DDB0 inside aic94xx driver itself caused SMP command timeout. I
hit this SMP timeout problem twice but I am not able to reproduce it since
then. Here is a fix that retries an SMP command.
Signed-off-by: Malahal Naineni <malahal@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The ->flags in struct request was split into two variables, in a recent
changeset. The merge of this change forgot to update SCSI's libsas,
probably because libsas was a very recent merge.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements the ability to set the minimum and maximum
linkrates for both libsas (for expanders) and aic94xx (for the host
phys). It also tidies up the setting of the hardware min and max to
make sure they're updated when the expander emits a change broadcast.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
At the moment we have two separate linkspeed enumerations covering
roughly the same values. This patch consolidates on a single one enum
sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the
aic94xx driver. Eventually I'll get around to removing the duplicated
fields in asd_sas_phy and sas_phy ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is the end point of the separate aic94xx driver based on the
original driver and transport class from Luben Tuikov
<ltuikov@yahoo.com>
The log of the separate development is:
Alexis Bruemmer:
o aic94xx: fix hotplug/unplug for expanderless systems
o aic94xx: disable split completion timer/setting by default
o aic94xx: wide port off expander support
o aic94xx: remove various inline functions
o aic94xx: use bitops
o aic94xx: remove queue comment
o aic94xx: remove sas_common.c
o aic94xx: sas remove depot's
o aic94xx: use available list_for_each_entry_safe_reverse()
o aic94xx: sas header file merge
James Bottomley:
o aic94xx: fix TF_TMF_NO_CTX processing
o aic94xx: convert to request_firmware interface
o aic94xx: fix hotplug/unplug
o aic94xx: add link error counts to the expander phys
o aic94xx: add transport class phy reset capability
o aic94xx: remove local_attached flag
o Remove README
o Fixup Makefile variable for libsas rename
o Rename sas->libsas
o aic94xx: correct return code for sas_discover_event
o aic94xx: use parent backlink port
o aic94xx: remove channel abstraction
o aic94xx: fix routing algorithms
o aic94xx: add backlink port
o aic94xx: fix cascaded expander properties
o aic94xx: fix sleep under lock
o aic94xx: fix panic on module removal in complex topology
o aic94xx: make use of the new sas_port
o rename sas_port to asd_sas_port
o Fix for eh_strategy_handler move
o aic94xx: move entirely over to correct transport class formulation
o remove last vestages of sas_rphy_alloc()
o update for eh_timed_out move
o Preliminary expander support for aic94xx
o sas: remove event thread
o minor warning cleanups
o remove last vestiges of id mapping arrays
o Further updates
o Convert aic94xx over entirely to the transport class end device and
o update aic94xx/sas to use the new sas transport class end device
o [PATCH] aic94xx: attaching to the sas transport class
o Add missing completion removal from prior patch
o [PATCH] aic94xx: attaching to the sas transport class
o Build fixes from akpm
Jeff Garzik:
o [scsi aic94xx] Remove ->owner from PCI info table
Luben Tuikov:
o initial aic94xx driver
Mike Anderson:
o aic94xx: fix panic on module insertion
o aic94xx: stub out SATA_DEV case
o aic94xx: compile warning cleanups
o aic94xx: sas_alloc_task
o aic94xx: ref count update
o aic94xx nexus loss time value
o [PATCH] aic94xx: driver assertion in non-x86 BIOS env
Randy Dunlap:
o libsas: externs not needed
Robert Tarte:
o aic94xx: sequence patch - fixes SATA support
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
jack_wang