Apply le16_to_cpu() to data read from the sensor in order to take into
account architecture endianness
Fixes: 290a6ce11d (iio: imu: add support to lsm6dsx driver)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch affects BME280 and BMP280. The readout of the calibration
data is moved to the probe function. Each sensor data access triggered
reading the full calibration data before this patch. According to the
datasheet, Section 4.4.2., the calibration data is stored in non-volatile
memory.
Since the calibration data does not change, and cannot be changed by the
user, we can reduce bus traffic by reading the calibration data once.
Additionally, proper organization of the data types enables removing
some odd casts in the compensation formulas.
Signed-off-by: Stefan Tatschner <stefan.tatschner@gmail.com>
Tested-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the registers are read out once per conversion interval. If
the reading is delayed as the conversion has not yet finished, this extra
time is treated as being part of the readout, although it should delay
the start of the poll interval. This results in the interval starting
slightly earlier in each iteration, until all time between reads is
spent polling the status registers instead of sleeping.
To fix this, the delay has to account for the state of the conversion
ready flag. Whenever the conversion is already finished, schedule the next
read on the regular interval, otherwise schedule it one interval after the
flag bit has been set.
Split the work function in two functions, one for the status poll and one
for reading the values, to be able to note down the time when the flag
bit is raised.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the timestamp is no longer (ab-)used to measure the function run time,
it can be taken at the correct time, i.e. when the conversion has finished.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iio timestamp clock is user selectable and may be non-monotonic. Also,
only part of the acquisition time is measured, thus the delay was longer
than intended.
Use a monotonic timestamp to track the time for the next poll iteration.
The timestamp is advanced by the sampling interval each iteration. In case
the conversion overrruns the register readout (i.e. fast sampling combined
with a slow bus), one or multiple samples will be dropped.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
This is a part of the patchset: https://lkml.org/lkml/2017/11/22/394
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the at91_adc.c file that fixes up a brace
warning found by the checkpatch.pl tool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return value in hx711_reset() should indicate status of dout otherwise the
calling function is reporting an error as false positive
If there are two reads too close to each other, then the second one will
never succeed. This happens especially when using buffered mode with both
channels enabled.
When changing the channel on every trigger event the former 100 ms are not
enough for waiting until the device indicates normal mode.
Wait up to 1 second until the device turns into normal mode.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add buffer to device data struct and add trigger function
Data format is quite simple:
voltage - channel 0 32 Bit
voltage - channel 1 32 Bit
timestamp 64 Bit
Using both channels at the same time is working quite slow because of
changing the channel which needs a dummy read.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion time can be up to 16 seconds (8 ms per channel, 2 channels,
1024 times averaging).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the datasheet states the CNVR flag is cleared by reading the
BUS_VOLTAGE register, it is actually cleared by reading any of the
voltage/current/power registers.
The behaviour has been confirmed by TI support:
http://e2e.ti.com/support/amplifiers/current-shunt-monitors/f/931/p/647053/2378282
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timestamp is inserted into the buffer after the sample data by
iio_push_to_buffers_with_timestamp, document the space requirement for
the timestamp.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iio_push_to_buffers_with_timestamp expects a void pointer, so the cast
is both unnecessary and misleading.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Meson8 devices the channel muxes are not programmed. This
results in garbage values when trying to read channels that are not set
up.
Fix this by initializing the channel 0 and 1 muxes in
MESON_SAR_ADC_CHAN_10_SW as well as the muxes for all other channels in
MESON_SAR_ADC_AUX_SW based on what the vendor driver does (which is
simply a 1:1 mapping of channel number and channel mux).
This only showed up on Meson8 devices, because for GXBB and newer BL30
is taking care of initializing the channel muxes.
This additionally fixes a typo in the
MESON_SAR_ADC_AUX_SW_MUX_SEL_CHAN_MASK macro because the old definition
assumed that the register fields were 2 bit wide, while they are
actually 3 bit wide.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GX SoCs use a 1.2 MHz ADC clock, while the older SoCs use a 1.14 MHz
clock.
A comment in the driver from Amlogic's GPL kernel says that it's
running at 1.28 MHz. However, it's actually programming a divider of
20 + 1. With a XTAL clock of 24 MHz this results in a frequency of
1.14 MHz. (their calculation might be based on a 27 MHz XTAL clock,
but this is not what we have on the Meson8 and Meson8b SoCs).
The ADC was still working with the 1.2MHz clock. In my own tests I did
not see a difference between 1.2 and 1.14 MHz (regardless of the clock
frequency used, the ADC results were identical).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Found with scripts/coccinelle/misc/boolconv.cocci.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Structures st_uvis25_i2c_regmap_config and st_uvis25_spi_regmap_config are
local to the source and do not need to be in global scope, so make them
both static.
Cleans up sparse warnings:
warning: symbol 'st_uvis25_i2c_regmap_config' was not declared. Should
it be static?
warning: symbol 'st_uvis25_spi_regmap_config' was not declared. Should
it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a sysfs attribute that exposes buffer data available to userspace.
This attribute can be checked at runtime to determine the overall buffer
fill level (across all allocated buffers).
Signed-off-by: Matt Fornero <matt.fornero@mathworks.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces the custom license information text with the appropriate
SPDX identifier. While the information here stays the same, it is easier
to read.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Harinath Nampally <harinath922@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getnstimeofday() suffers from the overflow in y2038 on 32-bit
architectures and requires a conversion into the nanosecond format that
we want here.
This changes ssp_parse_dataframe() to use ktime_get_real_ns() directly,
which does not have that problem.
An open question is what time base should be used here. Normally
timestamps should use ktime_get_ns() or ktime_get_boot_ns() to read
monotonic time instead of "real" time, which suffers from time jumps
due to settimeofday() calls or leap seconds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As discussed with Marc Zyngier: irq_sim_init() and its devres variant
should return the base of the allocated interrupt range on success
rather than 0. This will be modified later - first, change the way
users handle the return value of these routines.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge issue pointed out by Stephen in
drivers/iio/adc/meson_saradc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO core provides a handy GPIO_LOOKUP() macro to populate a struct
gpiod_lookup array without having to spell out attribute names (but
still avoid breakage when attributes within the struct are rearranged
or added).
The axp288_adc.c driver uses a similar macro to populate a struct
iio_map array. Make it available to others.
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
The I2C device ID table entries have the .driver_data field set, but they
are not used in the driver so weren't set in the OF device table entries.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "sana" clock is not used at SAR ADC module in Amlogic Meson SoC,
it is irrelevant for the SAR ADC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As per ABI temperature should be in milli Celsius after scaling,
not Celsius
Note on stable cc. This driver is breaking the standard IIO
ABI. (JC)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix build errors in kernel-doc notation. Symbols that end in '_'
have a special meaning, but adding a '*' makes them OK.
../drivers/iio/industrialio-core.c:635: ERROR: Unknown target name: "iio_val".
../drivers/iio/industrialio-core.c:642: ERROR: Unknown target name: "iio_val".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit 0f0796509c
("iio: remove gpio interrupt probing from drivers that use a single interrupt")
removed custom IRQ assignment for the drivers which are enumerated via
ACPI or OF. Unfortunately, some ACPI tables have IRQ line defined as
GpioIo() resource and thus automatic IRQ allocation will fail.
Partially revert the commit 0f0796509c to restore original behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pointer pdata is being assigned but it is never being used, hence
it is redundant and can be removed. Cleans up clang warning:
drivers/iio/accel/st_accel_core.c:952:3: warning: Value stored to 'pdata'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds an ACPI table to the driver and the ACPI ID of the sensor
on the tablet.
Signed-off-by: Luke Ross <luke@lukeross.name>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
add support for STMicroelectronics UVIS25 uv sensor
http://www.st.com/resource/en/datasheet/uvis25.pdf
- continuos mode support
- i2c support
- spi support
- trigger mode support
- system PM support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ASPEED SoC must deassert a reset in order to use the ADC peripheral.
The device tree bindings are updated to document the resets phandle, and
the example is updated to match what is expected for both the reset and
clock phandle. Note that the bindings should have always had the reset
controller, as the hardware is unusable without it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Maxim MAX30105 part adds a third LED (green) and uses a multi-LED
measuring mode producing three measurements
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Current code assumes always 2 measurements (6 bytes) have to be copied,
prepare for more flexibility
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move the programming of the mode setting from init() to
buffer_postenable()
Split out a separate function to
only update the power/shutdown bit
This changes permits to more easily implement different
modes of measurements in further patches
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Chip must not be in shutdown for reading temperature, so briefly leave
shutdown if buffer is not already running
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stalder <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Table 4 of the datasheet specifies the mode control, these are not
individual bits; add multi LED mode
Add multi-LED mode and fix MODE_MASK (3 bits wide, not 2)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lorenzo Bianconi