When the regulatory settings change, some channels might become invalid.
Disconnect interfaces acting on these channels, after giving userspace
code a grace period to leave them.
This mode is currently opt-in, and not all interface operating modes are
supported for regulatory-enforcement checks. A wiphy that wishes to use
the new enforcement code must specify an appropriate regulatory flag,
and all its supported interface modes must be supported by the checking
code.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@suse.com>
[fix some indentation, typos]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce commands to initiate and cancel TDLS channel-switching. Once
TDLS channel-switching is started, the lower level driver is responsible
for continually initiating channel-switch operations and returning to
the base (AP) channel to listen for beacons from time to time.
Upon cancellation of the channel-switch all communication between the
relevant TDLS peers will continue on the base channel.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds new iface type (NL80211_IFTYPE_OCB) representing
the OCB (Outside the Context of a BSS) mode.
When establishing a connection to the network a cfg80211_join_ocb
function is called (particular nl80211_command is added as well).
A mandatory parameters during the ocb_join operation are 'center
frequency' and 'channel width (5/10 MHz)'.
Changes done in mac80211 are minimal possible required to avoid
many warnings (warning: enumeration value 'NL80211_IFTYPE_OCB'
not handled in switch) during compilation. Full functionality
(where needed) is added in the following patch.
Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most code avoids having a default case in interface type switch
statements already, to make it easier to find places that need
to be extended. Change the code in the __cfg80211_leave() and
nl80211_key_allowed() functions to not have a default case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kernel will attempt to use the name if it is supplied,
but if name cannot be used for some reason, the default
phyX name will be used instead.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[while at it, use wiphy_name() instead of dev_name(),
fix format string issue reported by Kees Cook]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When freeing the keys stored for wireless extensions, clear the memory
to avoid having the key material stick around in memory "forever".
Similarly, when userspace overwrites a key, actually clear it instead
of just setting the key length to zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.
For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
This reverts commit dda444d524.
Channel switching code has been reworked and
improved significantly since the time original
locking issues were found.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently it can send regulatory domain change notification before any
NEW_WIPHY notification. Moreover, if rfill_register() fails, calling
wiphy_unregister() will send a DEL_WIPHY though no NEW_WIPHY had been
sent previously.
Thus reordering so it properly notifies NEW_WIPHY before any other.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.
To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently sending NEW_WIPHY events for renames (which
is a bit odd, but now can't be changed), but also send them
for really new devices that register.
Also send DEL_WIPHY events when a device is removed, the
event ID for this was already reserved.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the type of NL80211_ATTR_CSA_C_OFF_BEACON and
NL80211_ATTR_CSA_C_OFF_PRESP to be NLA_BINARY which allows
userspace to use beacons and probe responses with
multiple CSA counters.
This isn't breaking the API since userspace can
continue to use nla_put_u16 for this attributes, which
is equivalent to a single element u16 array.
In addition advertise max number of supported CSA counters.
This is needed when using CSA and eCSA IEs together.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver fails during HW restart or resume, the whole
stack goes into a very confused state with interfaces being
up while the hardware is down etc.
Address this by shutting down everything; we'll run into a
lot of warnings in the process but that's better than having
the whole stack get messed up.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports a new cfg80211_stop_iface() function.
This is intended for driver internal interface
combination management and channel switching.
Due to locking issues (it re-enters driver) the
call is asynchronous and uses cfg80211 event
list/worker.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These really can't trigger unless somebody messes up the code,
but don't make debugging it needlessly complicated, WARN and
return instead of BUG_ON().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return NOTIFY_DONE if we don't care this time's notification, return
NOTIFY_OK if we successfully handled this time's notification. That's
the formal way to do it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name wiphy_to_rdev is more accurate to describe what the function
does, i.e., return a pointer pointing to struct
cfg80211_registered_device.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get rid of the cfg80211_can_add_interface() and
cfg80211_can_change_interface() functions by moving that functionality
to mac80211. With this patch all interface combination checks are now
out of cfg80211 (except for the channel switch case which will be
addressed in a future commit).
Additionally, modify the ieee80211_check_combinations() function so
that an undefined chandef can be passed, in order to use it before a
channel is defined.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When dynamically creating interfaces from userspace, e.g. for P2P usage,
such interfaces are usually owned by the process that created them, i.e.
wpa_supplicant. Should wpa_supplicant crash, such interfaces will often
cease operating properly and cause problems on restarting the process.
To avoid this problem, introduce an ownership concept for interfaces. If
an interface is owned by a netlink socket, then it will be destroyed if
the netlink socket is closed for any reason, including if the process it
belongs to crashed. This gives us a race-free way to get rid of any such
interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of AP mode, the beacon interval is already reset to
zero inside cfg80211_stop_ap(), and in the other modes it
isn't relevant. Remove the assignment to remove a potential
race since the assignment isn't properly locked.
Reported-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "nl80211: send event when AP operation is stopped" added an
event to notify user space that an AP interface has been stopped, to
handle cases such as suspend etc. The event is sent regardless
if the stop AP flow was triggered by user space or due to internal state
change.
This might cause issues with wpa_supplicant/hostapd flows that consider
stop AP flow as a synchronous one, e.g., AP/GO channel change in the
absence of CSA support. In such cases, the flow will restart the AP
immediately after the stop AP flow is done, and only handle the stop
AP event after the current flow is done, and as a result stop the AP
again.
Change the current implementation to only send the event in case the
stop AP was triggered due to an internal reason.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the previous commit, when a scan finishes, it is in theory
possible to hit the following sequence:
1. interface starts being removed
2. scan is cancelled by driver and cfg80211 is notified
3. scan done work is scheduled
4. interface is removed completely, rdev->scan_req is freed,
event sent to userspace but scan done work remains pending
5. new scan is requested on another virtual interface
6. scan done work runs, freeing the still-running scan
To fix this situation, hang on to the scan done message and block
new scans while that is the case, and only send the message from
the work function, regardless of whether the scan_req is already
freed from interface removal. This makes step 5 above impossible
and changes step 6 to be
5. scan done work runs, sending the scan done message
As this can't work for wext, so we send the message immediately,
but this shouldn't be an issue since we still return -EBUSY.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an interface/wdev is removed, any ongoing scan should be
cancelled by the driver. This will make it call cfg80211, which
only queues a work struct. If interface/wdev removal is quick
enough, this can leave the scan request pending and processed
only after the interface is gone, causing a use-after-free.
Fix this by making sure the scan request is not pending after
the interface is destroyed. We can't flush or cancel the work
item due to locking concerns, but when it'll run it shouldn't
find anything to do. This leaves a potential issue, if a new
scan gets requested before the work runs, it prematurely stops
the running scan, potentially causing another crash. I'll fix
that in the next patch.
This was particularly observed with P2P_DEVICE wdevs, likely
because freeing them is quicker than freeing netdevs.
Reported-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Fixes: 4a58e7c384 ("cfg80211: don't "leak" uncompleted scans")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately I forgot this during the merge window, but the
patch seems small enough to go in as a fix. The userspace API
bug that was the reason for disabling it has long been fixed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
___cfg80211_scan_done() can be called in some cases
(e.g. on NETDEV_DOWN) before the low level driver
notified scan completion (which is indicated by
passing leak=true).
Clearing rdev->scan_req in this case is buggy, as
scan_done_wk might have already being queued/running
(and can't be flushed as it takes rtnl()).
If a new scan will be requested at this stage, the
scan_done_wk will try freeing it (instead of the
previous scan), and this will later result in
a use after free.
Simply remove the "leak" option, and replace it with
a standard WARN_ON.
An example backtrace after such crash:
Unable to handle kernel paging request at virtual address fffffee5
pgd = c0004000
[fffffee5] *pgd=9fdf6821, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
PC is at cfg80211_scan_done+0x28/0xc4 [cfg80211]
LR is at __ieee80211_scan_completed+0xe4/0x2dc [mac80211]
[<bf0077b0>] (cfg80211_scan_done+0x28/0xc4 [cfg80211])
[<bf0973d4>] (__ieee80211_scan_completed+0xe4/0x2dc [mac80211])
[<bf0982cc>] (ieee80211_scan_work+0x94/0x4f0 [mac80211])
[<c005fd10>] (process_one_work+0x1b0/0x4a8)
[<c0060404>] (worker_thread+0x138/0x37c)
[<c0066d70>] (kthread+0xa4/0xb0)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_leave stops sched scan when any station vif
is leaving. Add an explicit check and call it only
when the relevant vif (the one we scan on) is leaving.
Signed-off-by: Barak Bercovitz <barak@wizery.com>
[Eliad - changed the commit message a bit]
Signed-off-by: Eliad Peller <eliad@wizery.com>
[Johannes - add ASSERT_RTNL since that protects the pointer]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel switch announcement code has some major locking problems
which can cause a deadlock in worst case. A series of fixes has been
proposed, but these are non-trivial and need to be tested first.
Therefore disable CSA completely for 3.13.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the flag is entirely implemented in cfg80211, it should
have been a global feature flag (which I believe didn't
exist at the time). However, there's no reason to allow
drivers to unset the flag, so don't allow it and remove
the validation of NL80211_SCAN_FLAG_FLUSH.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to nl80211 API breakage, 5/10 MHz support is broken for
all drivers. Fixing it requires adding new API, but that
can't be done as a bugfix commit since that would require
either updating all APIs in the trees needing the bugfix or
cause different kernels to have incompatible API.
Therefore, just disable 5/10 MHz support for all drivers.
Cc: stable@vger.kernel.org [3.12]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since P2P device doesn't have a netdev associated to it,
we cannot prevent the user to start it when in RFKILL.
So refuse to even add it when in RFKILL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My locking rework/race fixes caused a regression in the
registration, causing uevent notifications for wireless
devices before the device is really fully registered and
available in nl80211.
Fix this by moving the device_add() under rtnl and move
the rfkill to afterwards (it can't be under rtnl.)
Reported-and-tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a P2P GO interface goes down, cfg80211 doesn't properly
tear it down, leading to warnings later. Add the GO interface
type to the enumeration to tear it down like AP interfaces.
Otherwise, we leave it pending and mac80211's state can get
very confused, leading to warnings later.
Cc: stable@vger.kernel.org
Reported-by: Ilan Peer <ilan.peer@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In most cases, host that receives IPv4 and IPv6 multicast/broadcast
packets does not do anything with these packets. Therefore the
reception of these unwanted packets causes unnecessary processing
and power consumption.
Packet coalesce feature helps to reduce number of received
interrupts to host by buffering these packets in firmware/hardware
for some predefined time. Received interrupt will be generated when
one of the following events occur.
a) Expiration of hardware timer whose expiration time is set to
maximum coalescing delay of matching coalesce rule.
b) Coalescing buffer in hardware reaches it's limit.
c) Packet doesn't match any of the configured coalesce rules.
This patch adds set/get configuration support for packet coalesce.
User needs to configure following parameters for creating a coalesce
rule.
a) Maximum coalescing delay
b) List of packet patterns which needs to be matched
c) Condition for coalescence. pattern 'match' or 'no match'
Multiple such rules can be created.
This feature needs to be advertised during driver initialization.
Drivers are supposed to do required firmware/hardware settings based
on user configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[fix kernel-doc, change free function, fix copy/paste error]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
If it *is* still set when the netdev is being deleted,
then we are about to leak a pointer. Warn and clean up
in that case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The change to use atomic_inc_return() for assigning the wiphy
index made the first wiphy index 1 instead of 0. This is fine,
but we all habitually type "phy0" when we're testing, so make
it go back to 0 instead of 1 by subtracting 1 from the index.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My big locking cleanups caused a problem by registering the
rfkill instance with the RTNL held, while the callback also
acquires the RTNL. This potentially causes a deadlock since
the two locks used (rfkill mutex and RTNL) can be acquired
in two different orders. Fix this by (un)registering rfkill
without holding the RTNL. This needs to be done after the
device struct is registered, but that can also be done w/o
holding the RTNL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arik Nemtsov