It is possible to request a transfer with a speed lower than supported
by the HW. This causes silent divider calculation underflow in
ssp_get_clk_div() which leads to a frequency higher than requested. Up to
maximum speed of the controller.
Set the minimum supported transfer speed and let the SPI core to
validate no transfers have speed lower than supported.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----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=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.
When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.
For example, with:
- ssp_clk = 50 MHz
- dev freq = 15 MHz
without this patch the SSP clock will be greater than 15 MHz:
- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others
Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add PCI IDs for SPI on Comet Lake.
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With dw_dmac, sometimes the request of a DMA channel fails because
the DMA driver is not ready, so an explicit dependency request
is necessary.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the type of the diagnostic message:
"no DMA channels available, using PIO"
from debug to warning.
The lack of an available DMA channel is very important regard the
spi-pxa2xx performance. The transfer speed can be reduced more than 50%.
So it is very important to warn the user about this, without enabling
the full SPI debug with CONFIG_SPI_DEBUG.
Moreover, enabling the full SPI debug only to enable this specific
debug message, the dmesg buffer fills quickly with a lot of
repetitive information during the SPI data transfer.
This cause the loss of all the first important messages
written during the initialization.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SPI device pointer in the remaining two error and warning prints in
pxa2xx_spi_transfer_one() instead of platform device of the controller
It make prints in the function uniform and more useful especially the
error print here as it can reveal the driver that has mapped the DMA
itself and attempts to transfer more than the maximum supported DMA
transfer length.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pointer to a SPI device is passed to pxa2xx_spi_transfer_one() so there
is no need to access it through the current SPI message pointer.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It's useful during debug to see what DMA burst size is.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some masters may have different DMA burst size than hard coded default.
In such case respect the value given by DMA burst size provided via
platform data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the commit b6ced294fb
("spi: pxa2xx: Switch to SPI core DMA mapping functionality")
switches to SPI core provided DMA helpers, it missed to setup maximum
supported DMA transfer length for the controller and thus users
mistakenly try to send more data than supported with the following
warning:
ili9341 spi-PRP0001:01: DMA disabled for transfer length 153600 greater than 65536
Setup maximum supported DMA transfer length in order to make users know
the limit.
Fixes: b6ced294fb ("spi: pxa2xx: Switch to SPI core DMA mapping functionality")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It's also a slave controller driver now, calling it "master" is slightly
misleading.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
There doesn't seem to be a way to empty TXFIFO on MMP2. The datasheet is
super-secret and the method described in Armada 16x manual won't work:
"The TXFIFO and RXFIFO are cleared to 0b0 when the SSPx port is reset or
disabled (by writing a 0b0 to the <Synchronous Serial Port Enable> field
in the SSP Control Register 0)."
# devmem 0xd4037008 # read SSSR
0x0000F204
# devmem 0xd4037000 32 0x07 # SSE off in SSCR0
# devmem 0xd4037000 32 0x87 # SSE on
# devmem 0xd4037008
0x0000F204
^ TXFIFO level is still 2. Sigh.
The OLPC 1.75 boot firmware leaves two bytes in the TXFIFO. Those are
basically throwaway bytes used in response to the messages from the EC.
The OLPC kernel copes with this by power-cycling the hardware. Perhaps
the firmware should do this instead.
Other than that, there's not much we can do other than complain loudly
until the garbage gets drained and discard the actual data... For the
OLPC EC this will work just fine and pushing more data to TXFIFO would
break further transactions.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Strobe a GPIO line when the slave TX FIFO is filled. This is how the
Embedded Controller on an OLPC XO-1.75 machine, that happens to be a SPI
master, learns that it can initiate a transaction.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested on an OLPC XO-1.75 machine, where the Embedded Controller happens
to be a SPI master.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS private register restoring in spi-pxa2xx.c: pxa2xx_spi_resume()
was added before there was no any other code restoring them. This was
changed after following commits for previous and current LPSS platforms:
c78b083066 ("ACPI / LPSS: custom power domain for LPSS")
41a3da2b8e ("mfd: intel-lpss: Save register context on suspend")
However there is one caveat: There is no LPSS private register context
save/restore for the Intel Lynxpoint in the Linux kernel code.
I did some debugging on one Lynxpoint based device I have and on it the
LPSS register context is not lost over suspend/resume cycle (s2idle).
Which happens for instance on Intel Braswell. I'm speculating but I guess
either firmware does it or the LPSS is kept always on Lynxpoint.
Given that we haven't needed to implement Lynxpoint LPSS I2C or UART
private register context save/restore over four years time I think we are
safe to remove this LPSS private register restoring during resume here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Ice Lake SPI host controller follows the Intel Cannon Lake but the
PCI IDs are different. Add the new PCI IDs to the driver supported
devices list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
clk_prepare_enable() can fail, so its return value should be checked and
acted upon.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3343b7a6d2 ("spi/pxa2xx: convert to the common clk framework")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the pump_transfers() transfer tasklet to transfer_one() hook the
SPI core calls to process single transfer instead of handling message
processing and chip select handling in the driver. This not only
simplifies the driver but also brings transfer statistics from the core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are going to rename and modify pump_transfers(). Prepare for it by
removing the string "pump_transfers:" from error and warning prints.
While at it make these user-visible strings single line in sources as it
helps source grepping from error reports.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DMA engine implementation of pxa2xx_spi_dma_prepare() don't use
the dma_burst argument. Remove it since it became unused after
commit 6356437e65 ("spi: spi-pxa2xx: remove legacy PXA DMA bits").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't leave runtime PM enabled in case devm_spi_register_controller()
returns with an error. Otherwise runtime PM will complain when driver is
reloaded:
[ 693.855811] pxa2xx-spi pxa2xx-spi.13: Unbalanced pm_runtime_enable!
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert to generalized SPI controller API introduced by the
commit 8caab75fd2 ("spi: Generalize SPI "master" to "controller"").
Inside driver variable name "master" is still used to indicate the driver
is master only.
While at it, change "unsigned cs" to "unsigned int cs" in
pxa2xx_spi_fw_translate_cs() to suppress checkpatch warning.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move SSP idle waiting before CS deassert from error and end of message
handling function giveback() to cs_deassert(). This ensures idle waiting
is done also if there is CS change between transfers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpiod_free() is an internal function for gpiolib, gpiod_put() is the
correct external function.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_free(gpio) simply does gpiod_free(gpio_to_desc(gpio)), so it's
simpler and cleaner to use gpiod_free directly.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
We still need to request/free GPIOs passed via the legacy path of
pxa2xx_spi_chip::gpio_cs, but we can use the gpiod API otherwise.
Consistently use the descriptor API instead of the legacy one.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO descriptors, when being requested, may configure pin at the same
time. In case of SPI chip select we shouldn't do any assumptions of the
state of pin since we don't know yet what chip is connected there and if
it uses high or low active state. So, leave the state of pin as is until
transfer will start.
Fixes: 99f499cd65 ("spi: pxa2xx: Add support for GPIO descriptor chip selects")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westeberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a valid case to call setup() following by setup_cs() several
times for the same chip.
With the commit
676a4e3bab ("spi: pxa2xx: Only claim CS GPIOs when the slave device is created")
it is not possible anymore due to GPIO line being requested already
during the first call to setup_cs().
For now, revert the commit to make things work again.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid hogging chip select GPIOs just because they are listed for the
master. They might be mulitplexed and, if no slave device is attached,
used for different purposes. Moreover, this strategy avoids having to
allocate a cs_gpiods structure.
Tested on the IOT2000 where the second SPI bus is connected to an
Arduino-compatible connector and multiplexed between SPI, GPIO and PWM
usage.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Cannonlake LPSS SPI has up to four chip selects per port like in
Broxton and is clocked like Sunrisepoint and Kaby Lake. Add a new type
LPSS_CNL_SSP and configuration that enable runtime chip select detection
and use the same FIFO thresholds than in Sunrisepoint.
Patch adds support for both Cannonlake SoC and PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the a device with edge-triggered interrupts, such as MSIs,
the interrupt handler has to ensure that there is a point in time during
its execution where all interrupts sources are silent so that a new
event can trigger a new interrupt again.
This is achieved here by disabling all interrupt sources for a moment
before processing them according to the status register. If a new
interrupt should have arrived after we read the status, it will now
re-trigger the interrupt, even in edge mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gemini Lake reuses the same LPSS SPI configuration as Broxton
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As suggested by Andy Shevchenko: Decouple this corner cause from the
general handling logic in ssp_int.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 7c7289a404 ("spi: pxa2xx: Default thresholds to PXA
configuration") while splitting up CE4100 code obviously missed a break
condition in one chunk. Add it here.
Looks like we have no active user of CE4100, though better to fix this later
than never.
Fixes: commit 7c7289a404 ("spi: pxa2xx: Default thresholds to PXA configuration")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kbuild test robot reports:
drivers/spi/spi-pxa2xx.c: In function ‘setup_cs’:
drivers/spi/spi-pxa2xx.c:1190:20: error: implicit declaration of function ‘desc_to_gpio’
...
Reason for this is the fact that those functions are declared in
linux/gpio/consumer.h which is not included in the driver. Fix this by
including it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula