An important information for the napi_poll tracepoint is knowing
the work done (packets processed) by the napi_poll() call. Add
both the work done and budget, as they are related.
Handle trace_napi_poll() param change in dropwatch/drop_monitor
and in python perf script netdev-times.py in backward compat way,
as python fortunately supports optional parameter handling.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 543e3a8da5.
Direct callers of __netpoll_setup() depend on it to set np->dev,
so we can't simply move that assignment up to netpoll_stup().
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netpoll_setup() does a dev_hold() on np->dev, the netpoll device. If it
fails, it correctly does a dev_put() but leaves np->dev set. If we call
netpoll_cleanup() after the failure, np->dev is still set so we do another
dev_put(), which decrements the refcount an extra time.
It's questionable to call netpoll_cleanup() after netpoll_setup() fails,
but it can be difficult to find the problem, and we can easily avoid it in
this case. The extra decrements can lead to hangs like this:
unregister_netdevice: waiting for bond0 to become free. Usage count = -3
Set and clear np->dev at the points where we dev_hold() and dev_put() the
device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason we were carrying the budget value around between the
various calls to napi->poll. If for example one of the drivers called had
a bug in which it returned a non-zero value for work this could result in
the budget value becoming negative.
Rather than carry around a value of budget that is 0 or less we can instead
just loop through and pass 0 to each napi->poll call. If any driver
returns a value for work done that is non-zero then we can report that
driver and continue rather than allowing a bad actor to make the budget
value negative and pass that negative value to napi->poll.
Note, the only actual change here is that instead of letting budget become
negative we are keeping it at 0 regardless of the value returned for work
since it should not be possible for the polling routine to do any actual
work with a budget of 0. So if the polling routine returns a non-0 value
we are just reporting it and continuing with a budget of 0 rather than
letting that work value be subtracted from the budget of 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers might call napi_disable while not holding the napi instance poll_lock.
In those instances, its possible for a race condition to exist between
poll_one_napi and napi_disable. That is to say, poll_one_napi only tests the
NAPI_STATE_SCHED bit to see if there is work to do during a poll, and as such
the following may happen:
CPU0 CPU1
ndo_tx_timeout napi_poll_dev
napi_disable poll_one_napi
test_and_set_bit (ret 0)
test_bit (ret 1)
reset adapter napi_poll_routine
If the adapter gets a tx timeout without a napi instance scheduled, its possible
for the adapter to think it has exclusive access to the hardware (as the napi
instance is now scheduled via the napi_disable call), while the netpoll code
thinks there is simply work to do. The result is parallel hardware access
leading to corrupt data structures in the driver, and a crash.
Additionaly, there is another, more critical race between netpoll and
napi_disable. The disabled napi state is actually identical to the scheduled
state for a given napi instance. The implication being that, if a napi instance
is disabled, a netconsole instance would see the napi state of the device as
having been scheduled, and poll it, likely while the driver was dong something
requiring exclusive access. In the case above, its fairly clear that not having
the rings in a state ready to be polled will cause any number of crashes.
The fix should be pretty easy. netpoll uses its own bit to indicate that that
the napi instance is in a state of being serviced by netpoll (NAPI_STATE_NPSVC).
We can just gate disabling on that bit as well as the sched bit. That should
prevent netpoll from conducting a napi poll if we convert its set bit to a
test_and_set_bit operation to provide mutual exclusion
Change notes:
V2)
Remove a trailing whtiespace
Resubmit with proper subject prefix
V3)
Clean up spacing nits
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: jmaxwell@redhat.com
Tested-by: jmaxwell@redhat.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we catch future netpoll_send_udp users who use it without
disabling irqs and also as a hint for poll_controller users.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use them to push skb->vlan_tci into the payload and avoid code
duplication.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace occurences of skb_get_queue_mapping() and follow-up
netdev_get_tx_queue() with an actual helper function.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a bonding master reclaims the netpoll info struct, slaves could
still hold a pointer to the reclaimed data. This patch fixes it: as
soon as netpoll_async_cleanup is called for a slave (eg. when
un-enslaved), we make sure that this slave doesn't point to the data.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the test in zap_completion_queue to test when it is safe to
free skbs in hard irq context with skb_irq_freeable ensuring we only
free skbs when it is safe, and removing the possibility of subtle
problems.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop taking the transmit lock when a network device has specified
NETIF_F_LLTX.
If no locks needed to trasnmit a packet this is the ideal scenario for
netpoll as all packets can be trasnmitted immediately.
Even if some locks are needed in ndo_start_xmit skipping any unnecessary
serialization is desirable for netpoll as it makes it more likely a
debugging packet may be trasnmitted immediately instead of being
deferred until later.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assumption that the skbs that make it to
netpoll_send_skb_on_dev are allocated with find_skb, such that
skb->users == 1 and nothing is attached that would prevent the skbs from
being freed from hard irq context.
Remove this assumption by replacing __kfree_skb on error paths with
dev_kfree_skb_irq (in hard irq context) and kfree_skb (in process
context).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_enable and netpoll_rx_disable functions have always
controlled polling the network drivers transmit and receive queues.
Rename them to netpoll_poll_enable and netpoll_poll_disable to make
their functionality clear.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that needs to surround ndo_start_xmit
from netpoll_send_skb_on_dev into netpoll_start_xmit.
It is an unfortunate fact that as the netpoll code has been maintained
the primary call site ndo_start_xmit learned how to handle vlans
and timestamps but the second call of ndo_start_xmit in queue_process
did not.
With the introduction of netpoll_start_xmit this associated logic now
happens at both call sites of ndo_start_xmit and should make it easy
for that to continue into the future.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make rx_skb_hook, and rx in struct netpoll depend on
CONFIG_NETPOLL_TRAP Make rx_lock, rx_np, and neigh_tx in struct
netpoll_info depend on CONFIG_NETPOLL_TRAP
Make the functions netpoll_rx_on, netpoll_rx, and netpoll_receive_skb
no-ops when CONFIG_NETPOLL_TRAP is not set.
Only build netpoll_neigh_reply, checksum_udp service_neigh_queue,
pkt_is_ns, and __netpoll_rx when CONFIG_NETPOLL_TRAP is defined.
Add helper functions netpoll_trap_setup, netpoll_trap_setup_info,
netpoll_trap_cleanup, and netpoll_trap_cleanup_info that initialize
and cleanup the struct netpoll and struct netpoll_info receive
specific fields when CONFIG_NETPOLL_TRAP is enabled and do nothing
otherwise.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bond slave device neigh_tx handling into service_neigh_queue.
In connection with neigh_tx processing remove unnecessary tests of
a NULL netpoll_info. As the netpoll_poll_dev has already used
and thus verified the existince of the netpoll_info.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we no longer need to receive packets to safely drain the
network drivers receive queue move netpoll_trap and netpoll_set_trap
under CONFIG_NETPOLL_TRAP
Making netpoll_trap and netpoll_set_trap noop inline functions
when CONFIG_NETPOLL_TRAP is not set.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the strategy of netpoll from dropping all packets received
during netpoll_poll_dev to calling napi poll with a budget of 0
(to avoid processing drivers rx queue), and to ignore packets received
with netif_rx (those will safely be placed on the backlog queue).
All of the netpoll supporting drivers have been reviewed to ensure
either thay use netif_rx or that a budget of 0 is supported by their
napi poll routine and that a budget of 0 will not process the drivers
rx queues.
Not dropping packets makes NETPOLL_RX_DROP unnecesary so it is removed.
npinfo->rx_flags is removed as rx_flags with just the NETPOLL_RX_ENABLED
flag becomes just a redundant mirror of list_empty(&npinfo->rx_np).
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper netpoll_rx_processing that reports when netpoll has
receive side processing to perform.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is already a warning for this case in the normal netpoll path,
but put a copy here in case how netpoll calls the poll functions
causes a differenet result.
netpoll will shortly call the napi poll routine with a budget 0 to
avoid any rx packets being processed. As nothing does that today
we may encounter drivers that have problems so a netpoll specific
warning seems desirable.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In poll_napi loop through all of the napi handlers even when the
budget falls to 0 to ensure that we process all of the tx_queues, and
so that we continue to call into drivers when our initial budget is 0.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves the control logic to the top level in netpoll_poll_dev
instead of having it dispersed throughout netpoll_poll_dev,
poll_napi and poll_one_napi.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netpoll depends on setting NETPOLL_RX_DROP before networking
drivers receive packets in interrupt context so that the packets can
be dropped. Move this setting into netpoll_poll_dev from
poll_one_napi so that if ndo_poll_controller happens to receive
packets we will drop the packets on the floor instead of letting the
packets bounce through the networking stack and potentially cause problems.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, to make netconsole start over IPv6, the source address
needs to be specified. Without a source address, netpoll_parse_options
assumes we're setting up over IPv4 and the destination IPv6 address is
rejected.
Check if the IP version has been forced by a source address before
checking for a version mismatch when parsing the destination address.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN tag handling code in netpoll_send_skb_on_dev() has two problems.
1) It exits without unlocking the TXQ.
2) It then tries to queue a NULL skb to npinfo->txq.
Reported-by: Ahmed Tamrawi <atamrawi@iastate.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now skb->data is passed to rx_hook() even if the skb
has not been linearised and without giving rx_hook() a way
to linearise it.
Change the rx_hook() interface and make it accept the skb
and the offset to the UDP payload as arguments. rx_hook() is
also renamed to rx_skb_hook() to ensure that out of the tree
users notice the API change.
In this way any rx_skb_hook() implementation can perform all
the needed operations to properly (and safely) access the
skb data.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've been hitting a NULL ptr deref while using netconsole because the
np->dev check and the pointer manipulation in netpoll_cleanup are done
without rtnl and the following sequence happens when having a netconsole
over a vlan and we remove the vlan while disabling the netconsole:
CPU 1 CPU2
removes vlan and calls the notifier
enters store_enabled(), calls
netdev_cleanup which checks np->dev
and then waits for rtnl
executes the netconsole netdev
release notifier making np->dev
== NULL and releases rtnl
continues to dereference a member of
np->dev which at this point is == NULL
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The received ARP request type in the Ethernet packet head is ETH_P_ARP other than ETH_P_IP.
[ Bug introduced by commit b7394d2429
("netpoll: prepare for ipv6") ]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Since we have at least one user of this function outside of CONFIG_NET
scope, we have to provide this function independently. The proposed
solution is to move it under lib/net_utils.c with corresponding
configuration variable and select wherever it is needed.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to the problem in pktgen, netpoll uses skb_tail_offset()
too, as the code is copied from pktgen.
Also use return values of skb_put() directly, this will simiplify
the code.
Reported-by: Thomas Graf <tgraf@suug.ch>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Daniel Borkmann <dborkmann@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer however skb->network_header is now
an offset.
This patch corrects the problem by adding a wrapper to return skb tail as
an offset regardless of the value of NET_SKBUFF_DATA_USES_OFFSET. It seems
that skb->tail that this offset may be more than 64k and some care has been
taken to treat such cases as an error.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_disable() will always return 0, it is no use and looks wordy,
so remove the unnecessary code and get rid of it in _dev_open and _dev_close.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value is reversed from mutex_trylock().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bart Van Assche recently reported a warning to me:
<IRQ> [<ffffffff8103d79f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8103d7fa>] warn_slowpath_null+0x1a/0x20
[<ffffffff814761dd>] mutex_trylock+0x16d/0x180
[<ffffffff813968c9>] netpoll_poll_dev+0x49/0xc30
[<ffffffff8136a2d2>] ? __alloc_skb+0x82/0x2a0
[<ffffffff81397715>] netpoll_send_skb_on_dev+0x265/0x410
[<ffffffff81397c5a>] netpoll_send_udp+0x28a/0x3a0
[<ffffffffa0541843>] ? write_msg+0x53/0x110 [netconsole]
[<ffffffffa05418bf>] write_msg+0xcf/0x110 [netconsole]
[<ffffffff8103eba1>] call_console_drivers.constprop.17+0xa1/0x1c0
[<ffffffff8103fb76>] console_unlock+0x2d6/0x450
[<ffffffff8104011e>] vprintk_emit+0x1ee/0x510
[<ffffffff8146f9f6>] printk+0x4d/0x4f
[<ffffffffa0004f1d>] scsi_print_command+0x7d/0xe0 [scsi_mod]
This resulted from my commit ca99ca14c which introduced a mutex_trylock
operation in a path that could execute in interrupt context. When mutex
debugging is enabled, the above warns the user when we are in fact
exectuting in interrupt context
interrupt context.
After some discussion, It seems that a semaphore is the proper mechanism to use
here. While mutexes are defined to be unusable in interrupt context, no such
condition exists for semaphores (save for the fact that the non blocking api
calls, like up and down_trylock must be used when in irq context).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
CC: Bart Van Assche <bvanassche@acm.org>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
DEFINE_STATIC_SRCU() defines srcu struct and do init at build time.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter contacted me with some notes regarding some smatch warnings in the
netpoll code, some of which I introduced with my recent netpoll locking fixes,
some which were there prior. Specifically they were:
net-next/net/core/netpoll.c:243 netpoll_poll_dev() warn: inconsistent
returns mutex:&ni->dev_lock: locked (213,217) unlocked (210,243)
net-next/net/core/netpoll.c:706 netpoll_neigh_reply() warn: potential
pointer math issue ('skb_transport_header(send_skb)' is a 128 bit pointer)
This patch corrects the locking imbalance (the first error), and adds some
parenthesis to correct the second error. Tested by myself. Applies to net-next
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With my recent commit I introduced two sparse warnings. Looking closer there
were a few more in the same file, so I fixed them all up. Basic rcu pointer
dereferencing suff.
I've validated these changes using CONFIG_PROVE_RCU while starting and stopping
netconsole repeatedly in bonded and non-bonded configurations
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: fengguang.wu@intel.com
CC: David Miller <davem@davemloft.net>
CC: eric.dumazet@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer