Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the all the slot processing for the completion queue is done
in ISR context. It is judged that the slot processing can take a long
time, especially when a SATA NCQ completes (upto 32 slots).
So, as a solution, defer the bulk of the ISR processing to tasklet
context. Each CQ will have its down tasklet.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the function to set PHY min and max linkrate through
sysfs interface.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes the value of hisi_sas_device.running_req
would go negative unless we have the check for
running_req >= 0 before trying to decrement.
This is because using running_req is not thread-safe.
As such, the value for running_req may be actually incorrect,
so use atomic64_t instead.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently slots are allocated from queues in a round-robin fashion.
This causes a problem for internal commands in device mode. For this
mode, we should ensure that the internal abort command is the last
command seen in the host for that device. We can only ensure this when
we place the internal abort command after the preceding commands for
device that in the same queue, as there is no order in which the host
will select a queue to execute the next command.
This queue restriction makes supporting scsi mq more tricky in
the future, but should not be a blocker.
Note: Even though v1 hw does not support internal abort, the
allocation method is chosen to be the same for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hip06 D03 and hip07 D05 boards have different reference clock
frequencies for the SAS controller.
Register PHY_CTRL needs to be programmed differently according to this
frequency, so add support for this.
The default register setting in PHY_CTRL is for 50MHz, so only update
this register when the refclk frequency is 66MHz.
For ACPI we expect the _RST handler to set the correct value for
PHY_CTRL (we're forced to take different approach for DT and ACPI as
ACPI does not support fixed-clock device).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimise by saving an avoidable read in the get_free_slot function. The
delivery queue write pointer will only be updated by software, so don't
bother re-reading what was already written in the previous call to
start_delivery function.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimise by saving an avoidable read in the cq interrupt. The queue
read pointer will only be updated by software, so don't bother
re-reading what was already written in the previous interrupt.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add main code for internal abort functionality.
The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.
Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.
Two modes of internal abort are supported:
- device
- individual command
For device, when the internal abort is issued all commands in the host
for that device are aborted. For a single command, only that command is
aborted if it is still in the host.
In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add methods to use HW specific versions of functions to allocate slot
and device. HW specific methods are permitted to workaround device id
vs IPTT collision issue in v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a function to abort a slot (task) in the target
device and then cleanup and complete the task.
The function is called from work queue context as
it cannot be called from the context where it is
triggered (interrupt).
Flag hisi_sas_slot.abort is added as the flag used
in the slot error handler to indicate whether the
slot needs to be aborted in the sdev prior to
cleanup and finish.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hisi_sas driver is required to support both device tree and
ACPI. The scanning of the device properties now uses the Unified Device
Properties API, which serves both OF and ACPI.
Since syscon is not supported by ACPI, syscon is only used in the driver
when device tree is used.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since hisi_sas_itct format is different between v1 and v2 hw, give more
general names for some fields.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the error record structure is different for v2 hw, make
hisi_sas_err_record opaque and add hisi_sas_err_record_v1.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since v2 hw only supports 2048 itct entries, as opposed to 4096 for v1
hw, set the max itct entries to the lower of the two.
It is not anticipated that any device with v1 will ever require to
connect > 2048 devices.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since v2 hardware permits different numbers of commands to v1, set this
as configurable in hisi_sas_hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate DEV_IS_EXPANDER to hisi_sas.h as it will be required for v2 hw
support.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is preferred that drivers use platform_get_irq() instead of
irq_of_parse_and_map(), so replace.
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Originally the driver would use of_irq_count to calculate how much
memory is required for storing the interrupt names, since the number of
interrupt sources for the controller is variable. Since of_irq_count
cannot be used by the driver, use fixed names.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add method for lldd_control_phy. Currently link rate control and spinup
hold is unsupported.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functions for scsi host template scan_finished and scan_start
methods.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for smp function, which allows devices attached by expander
to be controlled.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add abnormal irq handler. This handler is concerned with phy down event.
Also add port formed and port deformed handlers.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functions to deal with lldd_dev_found and lldd_dev_gone.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add cq interrupt handler and also slot error handler function.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add path to send ssp command to HW.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add code to interrupts, so now we can get a phy up interrupt when a disk
is connected.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add module init code for v1 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Include initialisation.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS address for the HBA comes from the device tree.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Each completion queue has a structure. This is mainly for passing to irq
handler so we know which queue the irq occured on.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add functionality to init slot indexing.
Slot indexing is for the host to track which slots (or tags) are free
and which are used.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scan the device tree for all properties. Also do this:
- do ioremap for SAS registers
- allocate memory for interrupt names
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry