The Retagging Table is an optional feature that allows the switch to
match frames against a {ingress port, egress port, vid} rule and change
their VLAN ID. The retagged frames are by default clones of the original
ones (since the hardware-foreseen use case was to mirror traffic for
debugging purposes and to tag it with a special VLAN for this purpose),
but we can force the original frames to be dropped by removing the
pre-retagging VLAN from the port membership list of the egress port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the register definitions for the:
- VL Lookup Table
- VL Policing Table
- VL Forwarding Table
- VL Forwarding Parameters Table
These are needed in order to perform TTEthernet operations: QoS
classification, flow-based policing and/or frame redirecting with the
switch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.
Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most commonly called function in the driver is long due for a
rename. The "packed" word is redundant (it doesn't make sense to
transfer an unpacked structure, since that is in CPU endianness yadda
yadda), and the "spi" word is also redundant since argument 2 of the
function is SPI_READ or SPI_WRITE.
As for the sja1105_spi_send_long_packed_buf function, it is only being
used from sja1105_spi.c, so remove its global prototype.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support tc-taprio offload, the TTEthernet egress scheduling
core registers must be made visible through the static interface.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.
To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This table is used to program the switch to emit "meta" follow-up
Ethernet frames (which contain partial RX timestamps) after each
link-local frame that was trapped to the CPU port through MAC filtering.
This includes PTP frames.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management routes are one-shot FDB rules installed on the CPU port for
sending link-local traffic. They are a prerequisite for STP, PTP etc to
work.
Also make a note that removing a management route was not supported on
the previous generation of switches.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conceptually, if an entry is not found in the requested hardware table,
it is not an invalid request - so change the error returned
appropriately.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed in order to implement the switchdev FDB callbacks.
Compared to the E/T generation, not only the ABI (bit offsets) is
different, but also the introduction of the HOSTCMD field which permits
O(1) TCAM search for an FDB entry. Make use of the newly introduce
OP_SEARCH to permit that. It will be used while adding and deleting an
FDB entry (to see whether it exists or not).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA callbacks were written with the E/T (first generation) in mind,
which is quite different.
For P/Q/R/S completely new implementations need to be provided, which
are held as function pointers in the priv->info structure. We are
taking a slightly roundabout way for this (a function from
sja1105_main.c reads a structure defined in sja1105_spi.c that
points to a function defined in sja1105_main.c), but it is what it is.
The FDB dump callback works for both families, hence no function pointer
for that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only a single dynamic configuration table of the SJA1105 P/Q/R/S
supports this operation: the FDB.
To keep the existing structure in place (sja1105_dynamic_config_read and
sja1105_dynamic_config_write) and not introduce any new function, a
convention is made for sja1105_dynamic_config_read that a negative index
argument denotes a search for the entry provided as argument.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was inadvertently copied from the SJA1105 E/T structure and not
tested. Cross-checking with the P/Q/R/S documentation (UM11040) makes
it immediately obvious what the correct bit offsets for this field are.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is merely an implementation detail and should be hidden
from the sja1105_dynamic_config.h header, which provides to the rest of
the driver an abstract access to the dynamic configuration interface of
the switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean