Conflicts:
arch/mips/net/bpf_jit.c
drivers/net/can/flexcan.c
Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.
This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.
The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free resources before being disconnected from phy and calling core driver is
wrong and should not happen. It avoids a delay of 4-5s caused by the timeout of
phy_disconnect().
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a platform glue layer for Rockchip SoCs which
support arc-emac driver. It ensures that regulator for the rmii is on
before trying to connect to the ethernet controller. It applies right
speed and mode changes to the grf when ethernet settings change.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused 'dev' variable from arc_emac_remove(), since it's
not being used any more.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms have special bank registers which might be used to
select the correct clock or the right mode for Media Indepent Interface
controllers. Sometimes, it is also required to activate vcc regulators
in the right order to supply the ethernet controller at the right time.
This patch is an architecture refactoring of the arc-emac device driver.
It adds a new software design which allows to add specific platform
glue layer. Each platform has now its own module which performs custom
initialization and remove for the target and then calls to the
core driver.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an api changes for the emac_mdio.c module.
It will be required later when arc_emac_probe/arc_emac_remove
will no longer use 'struct platform_device'.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation of an api changes for the emac_main.c module.
The involved functions are arc_emac_probe and arc_emac_remove.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer to the struct net_device in the private data is only
assigned but never used, so delete it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
arc_emac_priv, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the set_rx_mode function to enable/disable
promiscuous or all-multicast modes and to update the multicast
filtering list of the device.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe function at the moment only frees the netdev but does not disconnect
the phy or removes the mdio bus it registered.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC address retrieved from dt was not actually written to the
hardware. This meant proper communication was only possible after
changing the MAC address.
Fix that by always writing the mac address during probing.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Fixes: e4f2379db6 ("ethernet/arc/arc_emac - Add new driver")
From: Eric Dumazet <edumazet@google.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARC emac driver was the only in-tree to parse a PHY device
'max-speed' property but yet failed to do it correctly because
'max-speed' is supposed to set a PHY device supported features, not the
advertising features as it was done.
Now that of_mdiobus_register() takes care of doing that, remove the
custom 'max-speed' parsing code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Add missing platform_set_drvdata() in arc_emac_probe(), otherwise
calling platform_get_drvdata() in arc_emac_remove() may returns NULL.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking if MAC address is valid using is_valid_ether_addr() is already done in
of_get_mac_address(). While at it, reorganize checking so it matches checks in
other drivers.
Signed-off-by: Luka Perkov <luka@openwrt.org>
CC: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
copying large files to a NFS mounted host was taking absurdly large
time.
Turns out that TX BD reclaim had a sublte bug.
Loop starts off from @txbd_dirty cursor and stops when it hits a BD
still in use by controller. However when it stops it needs to keep the
cursor at that very BD to resume scanning in next iteration. However it
was erroneously incrementing the cursor, causing the next scan(s) to
fail too, unless the BD chain was completely drained out.
[ARCLinux]$ ls -l -sh /disk/log.txt
17976 -rw-r--r-- 1 root root 17.5M Sep /disk/log.txt
========== Before =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real 31m 7.95s
user 0m 0.00s
sys 0m 0.10s
========== After =====================
[ARCLinux]$ time cp /disk/log.txt /mnt/.
real 0m 24.33s
user 0m 0.00s
sys 0m 0.19s
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com> (commit_signer:3/4=75%)
Cc: "David S. Miller" <davem@davemloft.net> (commit_signer:3/4=75%)
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: arc-linux-dev@synopsys.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially I improperly set a boundary for maximum number of input
packets to process on NAPI poll ("work") so it might be more than
expected amount ("weight").
This was really harmless but seeing WARN_ON_ONCE on every device boot is
not nice. So trivial fix ("<" instead of "<=") is here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by "kbuild test robot" there were some errors and warnings
on attempt to build kernel with "make ARCH=powerpc allmodconfig".
And this patch addresses both errors and warnings.
Below is a list of introduced changes:
1. Fix compile-time errors (misspellings in "dma_unmap_single") on PPC.
2. Use DMA address instead of "skb->data" as a pointer to data buffer.
This fixed warnings on pointer to int conversion on 64-bit systems.
3. Re-implemented initial allocation of Rx buffers in "arc_emac_open" in
the same way they're re-allocated during operation (receiving packets).
So once again DMA address could be used instead of "skb->data".
4. Explicitly use EMAC_BUFFER_SIZE for Rx buffers allocation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: netdev@vger.kernel.org
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Joe Perches <joe@perches.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller