When kgdboc is compiled as a module all of the "ekgdboc" and
"kgdb_earlycon" code isn't useful and, in fact, breaks compilation.
This is because early_param() isn't defined for modules and that's how
this code gets configured.
It turns out that this was broken by commit eae3e19ca9 ("kgdboc:
Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc") and then
made worse by commit 220995622d ("kgdboc: Add kgdboc_earlycon to
support early kgdb using boot consoles"). I guess the #ifdef wasn't
so useless, even if it wasn't obvious why it was useful. When kgdboc
was compiled as a module only "CONFIG_KGDB_SERIAL_CONSOLE_MODULE" was
defined, not "CONFIG_KGDB_SERIAL_CONSOLE". That meant that the old
module.
Let's basically do the same thing that the old code (pre-removal of
the #ifdef) did but use "IS_BUILTIN(CONFIG_KGDB_SERIAL_CONSOLE)" to
make it more obvious what the point of the check is. We'll fix
kgdboc_earlycon in a similar way.
Fixes: 220995622d ("kgdboc: Add kgdboc_earlycon to support early kgdb using boot consoles")
Fixes: eae3e19ca9 ("kgdboc: Remove useless #ifdef CONFIG_KGDB_SERIAL_CONSOLE in kgdboc")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200519084345.1.I91670accc8a5ddabab227eb63bb4ad3e2e9d2b58@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Pull uaccess/access_ok updates from Al Viro:
"Removals of trivially pointless access_ok() calls.
Note: the fiemap stuff was removed from the series, since they are
duplicates with part of ext4 series carried in Ted's tree"
* 'uaccess.access_ok' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vmci_host: get rid of pointless access_ok()
hfi1: get rid of pointless access_ok()
usb: get rid of pointless access_ok() calls
lpfc_debugfs: get rid of pointless access_ok()
efi_test: get rid of pointless access_ok()
drm_read(): get rid of pointless access_ok()
via-pmu: don't bother with access_ok()
drivers/crypto/ccp/sev-dev.c: get rid of pointless access_ok()
omapfb: get rid of pointless access_ok() calls
amifb: get rid of pointless access_ok() calls
drivers/fpga/dfl-afu-dma-region.c: get rid of pointless access_ok()
drivers/fpga/dfl-fme-pr.c: get rid of pointless access_ok()
cm4000_cs.c cmm_ioctl(): get rid of pointless access_ok()
nvram: drop useless access_ok()
n_hdlc_tty_read(): remove pointless access_ok()
tomoyo_write_control(): get rid of pointless access_ok()
btrfs_ioctl_send(): don't bother with access_ok()
fat_dir_ioctl(): hadn't needed that access_ok() for more than a decade...
dlmfs_file_write(): get rid of pointless access_ok()
only copy_to_user() is done to the address in question
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To support BT use case over UART at baud rate of 3.2 Mbps,
we need SE clocks to run at 51.2MHz frequency. Previously this
frequency was not available in clk src, so, we were requesting
for 102.4 MHz and dividing it internally by 2 to get 51.2MHz.
As now 51.2MHz frequency is made available in clk src,
adding this frequency to UART frequency table.
We will save significant amount of power, if 51.2 is used
because it belongs to LowSVS range whereas 102.4 fall into
Nominal category.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1590747282-5487-1-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AGTIM flag must be cleared explicitly, otherwise the IRQ handler
will be called in an endless loop.
Fortunately, this issue currently doesn't affect mainline kernels in
practice, as the the RX FIFO trigger level is set to 1 in UFCR. When
setting the trigger level to a higher number, the issue is trivially
reproducible by any RX without DMA that doesn't fill the FIFO up to the
configured level.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200528154747.14201-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81966 is a LPC/eSPI to 6 UARTs SuperIO. It has fully compatible
with F81866. It's also need check the IRQ mode with system assigned.
F81966 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Cc: Ji-Ze Hong (Peter Hong) <peter_hong@fintek.com.tw>
Link: https://lore.kernel.org/r/20200528022429.32078-1-hpeter+linux_kernel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series of uart controllers is able to work in IrDA mode.
Add per-port flag to the device-tree to enable that feature if needed.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200529055058.1606910-3-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e8759ad17d ("serial: uapi: Add support for bus termination")
introduced the ability to enable rs485 bus termination from user space.
So far the feature is only used by a single driver, 8250_exar.c, using a
hardcoded GPIO pin specific to Siemens IOT2040 products.
Provide for a more generic solution by allowing specification of an
rs485 bus termination GPIO pin in the device tree: Amend the serial
core to retrieve the GPIO from the device tree (or ACPI table) and amend
the default ->rs485_config() callback for 8250 drivers to change the
GPIO on request from user space.
Perhaps 8250_exar.c can be converted to the generic approach in a
follow-up patch.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/94c6c800d1ca9fa04766dd1d43a8272c5ad4bedd.1589811297.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The parameter is named p while the documentation talks about up.
Fix the doc to be in line with the code.
Fixes: 058bc104f7 ("serial: 8250: Generalize rs485 software emulation")
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200517215610.2131618-2-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When k_ascii is invoked several times in a row there is a potential for
signed integer overflow:
UBSAN: Undefined behaviour in drivers/tty/vt/keyboard.c:888:19 signed integer overflow:
10 * 1111111111 cannot be represented in type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.11 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
ubsan_epilogue+0xe/0x30 lib/ubsan.c:154
handle_overflow+0xdc/0xf0 lib/ubsan.c:184
__ubsan_handle_mul_overflow+0x2a/0x40 lib/ubsan.c:205
k_ascii+0xbf/0xd0 drivers/tty/vt/keyboard.c:888
kbd_keycode drivers/tty/vt/keyboard.c:1477 [inline]
kbd_event+0x888/0x3be0 drivers/tty/vt/keyboard.c:1495
While it can be worked around by using check_mul_overflow()/
check_add_overflow(), it is better to introduce a separate flag to
signal that number pad is being used to compose a symbol, and
change type of the accumulator from signed to unsigned, thus
avoiding undefined behavior when it overflows.
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200525232740.GA262061@dtor-ws
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some embedded devices still use these serial ports; make sure they're
still enabled by default on architectures more likely to have them, to
avoid rendering someone's console unavailable.
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Fixes: dc56ecb81a ("serial: 8250: Support disabling mdelay-filled probes of 16550A variants")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Link: https://lore.kernel.org/r/a20b5fb7dd295cfb48160eecf4bdebd76332d67d.1590509426.git.josh@joshtriplett.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hvc_open sets tty->driver_data to NULL when open fails at some point.
Typically, the failure happens in hp->ops->notifier_add(). If there is
a racing process which tries to open such mangled tty, which was not
closed yet, the process will crash in hvc_open as tty->driver_data is
NULL.
All this happens because close wants to know whether open failed or not.
But ->open should not NULL this and other tty fields for ->close to be
happy. ->open should call tty_port_set_initialized(true) and close
should check by tty_port_initialized() instead. So do this properly in
this driver.
So this patch removes these from ->open:
* tty_port_tty_set(&hp->port, NULL). This happens on last close.
* tty->driver_data = NULL. Dtto.
* tty_port_put(&hp->port). This happens in shutdown and until now, this
must have been causing a reference underflow, if I am not missing
something.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Reported-and-tested-by: Raghavendra <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200526145632.13879-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Freescale IMX console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200525105952.13744-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the driver probes just fine and binds all its resources even
if the physical device is not present.
As the device lacks an identification register, let's at least read the
LSR register to check whether a device at the configured address responds
to the request at all.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-7-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the interrupt line is shared with other devices, the IRQ must be
level-triggered, as only one device can trigger a falling edge. To support
this, try to acquire the IRQ with IRQF_TRIGGER_LOW|IRQF_SHARED first.
Interrupt controllers that lack support for level-triggers will return an
error, in which case the driver will now retry the acqusition with
IRQF_TRIGGER_FALLING, which was also the default before.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-6-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a threaded IRQ handler to get rid of the irq_work kthread.
This also allows for the driver to use interrupts generated by
a threaded controller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-5-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently only uses IRQF_TRIGGER_FALLING if the probing
happened without a device-tree setup. The device however will always
generate falling edges on its IRQ line, so let's use that flag in
all cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200521091152.404404-4-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting the previous fix "tty: n_gsm: Fix waking up upper tty
layer when room available". It was suggested to switch from a while to
a for loop, but when doing it, there was a remaining bogus i++.
This patch removes this i++ and also reorganizes the code making it more
compact.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the length is zero then the print_hex_dump_bytes won't output
anything, so testing the length before the call is unnecessary.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200518084517.2173242-2-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to display console messages in low power mode, console pins
must be kept active after suspend call.
Initial patch "serial: stm32: add support for no_console_suspend" was part
of "STM32 usart power improvement" series, but as dependancy to
console_suspend pinctl state has been removed to fit with Rob comment [1],
this patch has no more dependancy with any other patch of this series.
[1] https://lkml.org/lkml/2019/7/9/451
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Link: https://lore.kernel.org/r/20200519094104.27082-1-erwan.leray@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to enable kgdb to debug the early parts of the kernel.
Unfortunately kgdb normally is a client of the tty API in the kernel
and serial drivers don't register to the tty layer until fairly late
in the boot process.
Serial drivers do, however, commonly register a boot console. Let's
enable the kgdboc driver to work with boot consoles to provide early
debugging.
This change co-opts the existing read() function pointer that's part
of "struct console". It's assumed that if a boot console (with the
flag CON_BOOT) has implemented read() that both the read() and write()
function are polling functions. That means they work without
interrupts and read() will return immediately (with 0 bytes read) if
there's nothing to read. This should be a safe assumption since it
appears that no current boot consoles implement read() right now and
there seems no reason to do so unless they wanted to support
"kgdboc_earlycon".
The normal/expected way to make all this work is to use
"kgdboc_earlycon" and "kgdboc" together. You should point them both
to the same physical serial connection. At boot time, as the system
transitions from the boot console to the normal console (and registers
a tty), kgdb will switch over.
One awkward part of all this, though, is that there can be a window
where the boot console goes away and we can't quite transtion over to
the main kgdboc that uses the tty layer. There are two main problems:
1. The act of registering the tty doesn't cause any call into kgdboc
so there is a window of time when the tty is there but kgdboc's
init code hasn't been called so we can't transition to it.
2. On some serial drivers the normal console inits (and replaces the
boot console) quite early in the system. Presumably these drivers
were coded up before earlycon worked as well as it does today and
probably they don't need to do this anymore, but it causes us
problems nontheless.
Problem #1 is not too big of a deal somewhat due to the luck of probe
ordering. kgdboc is last in the tty/serial/Makefile so its probe gets
right after all other tty devices. It's not fun to rely on this, but
it does work for the most part.
Problem #2 is a big deal, but only for some serial drivers. Other
serial drivers end up registering the console (which gets rid of the
boot console) and tty at nearly the same time.
The way we'll deal with the window when the system has stopped using
the boot console and the time when we're setup using the tty is to
keep using the boot console. This may sound surprising, but it has
been found to work well in practice. If it doesn't work, it shouldn't
be too hard for a given serial driver to make it keep working.
Specifically, it's expected that the read()/write() function provided
in the boot console should be the same (or nearly the same) as the
normal kgdb polling functions. That means continuing to use them
should work just fine. To make things even more likely to work work
we'll also trap the recently added exit() function in the boot console
we're using and delay any calls to it until we're all done with the
boot console.
NOTE: there could be ways to use all this in weird / unexpected ways.
If you do something like this, it's a bit of a buyer beware situation.
Specifically:
- If you specify only "kgdboc_earlycon" but not "kgdboc" then
(depending on your serial driver) things will probably work OK, but
you'll get a warning printed the first time you use kgdb after the
boot console is gone. You'd only be able to do this, of course, if
the serial driver you're running atop provided an early boot console.
- If your "kgdboc_earlycon" and "kgdboc" devices are not the same
device things should work OK, but it'll be your job to switch over
which device you're monitoring (including figuring out how to switch
over gdb in-flight if you're using it).
When trying to enable "kgdboc_earlycon" it should be noted that the
names that are registered through the boot console layer and the tty
layer are not the same for the same port. For example when debugging
on one board I'd need to pass "kgdboc_earlycon=qcom_geni
kgdboc=ttyMSM0" to enable things properly. Since digging up the boot
console name is a pain and there will rarely be more than one boot
console enabled, you can provide the "kgdboc_earlycon" parameter
without specifying the name of the boot console. In this case we'll
just pick the first boot that implements read() that we find.
This new "kgdboc_earlycon" parameter should be contrasted to the
existing "ekgdboc" parameter. While both provide a way to debug very
early, the usage and mechanisms are quite different. Specifically
"kgdboc_earlycon" is meant to be used in tandem with "kgdboc" and
there is a transition from one to the other. The "ekgdboc" parameter,
on the other hand, replaces the "kgdboc" parameter. It runs the same
logic as the "kgdboc" parameter but just relies on your TTY driver
being present super early. The only known usage of the old "ekgdboc"
parameter is documented as "ekgdboc=kbd earlyprintk=vga". It should
be noted that "kbd" has special treatment allowing it to init early as
a tty device.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.8.I8fba5961bf452ab92350654aa61957f23ecf0100@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This file is only ever compiled if that config is on since the
Makefile says:
obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
Let's get rid of the useless #ifdef.
Reported-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200507130644.v4.7.Icb528f03d0026d957e60f537aa711ada6fd219dc@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
If you build CONFIG_KGDB_SERIAL_CONSOLE into the kernel then you
should be able to have KGDB init itself at bootup by specifying the
"kgdboc=..." kernel command line parameter. This has worked OK for me
for many years, but on a new device I switched to it stopped working.
The problem is that on this new device the serial driver gets its
probe deferred. Now when kgdb initializes it can't find the tty
driver and when it gives up it never tries again.
We could try to find ways to move up the initialization of the serial
driver and such a thing might be worthwhile, but it's nice to be
robust against serial drivers that load late. We could move kgdb to
init itself later but that penalizes our ability to debug early boot
code on systems where the driver inits early. We could roll our own
system of detecting when new tty drivers get loaded and then use that
to figure out when kgdb can init, but that's ugly.
Instead, let's jump on the -EPROBE_DEFER bandwagon. We'll create a
singleton instance of a "kgdboc" platform device. If we can't find
our tty device when the singleton "kgdboc" probes we'll return
-EPROBE_DEFER which means that the system will call us back later to
try again when the tty device might be there.
We won't fully transition all of the kgdboc to a platform device
because early kgdb initialization (via the "ekgdboc" kernel command
line parameter) still runs before the platform device has been
created. The kgdb platform device is merely used as a convenient way
to hook into the system's normal probe deferral mechanisms.
As part of this, we'll ever-so-slightly change how the "kgdboc=..."
kernel command line parameter works. Previously if you booted up and
kgdb couldn't find the tty driver then later reading
'/sys/module/kgdboc/parameters/kgdboc' would return a blank string.
Now kgdb will keep track of the string that came as part of the
command line and give it back to you. It's expected that this should
be an OK change.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.3.I4a493cfb0f9f740ce8fd2ab58e62dc92d18fed30@changeid
[daniel.thompson@linaro.org: Make config_mutex static]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
This reverts commit 81eaadcae8.
Commit 81eaadcae8 ("kgdboc: disable the console lock when in kgdb")
is no longer needed now that we have the patch ("kgdb: Disable
WARN_CONSOLE_UNLOCKED for all kgdb"). Revert it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20200507130644.v4.2.I02258eee1497e55bcbe8dc477de90369c7c7c2c5@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
An uninitialised spin lock for sifive serial console raises a bad
magic spin_lock error as reported and discussed here [1].
Initialising the spin lock resolves the issue.
The fix is tested on HiFive Unleashed A00 board with Linux 5.7-rc4
and OpenSBI v0.7
[1] https://lore.kernel.org/linux-riscv/b9fe49483a903f404e7acc15a6efbef756db28ae.camel@wdc.com
Fixes: 45c054d081 ("tty: serial: add driver for the SiFive UART")
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1589019852-21505-2-git-send-email-sagar.kadam@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user is not supposed to thinker with the underlying sysrq_key_op.
Make that explicit by adding a handful of const notations.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://lore.kernel.org/r/20200513214351.2138580-2-emil.l.velikov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export a pointer to the sysrq_get_key_op(). This way we can cleanly
unregister it, instead of the current solutions of modifuing it inplace.
Since __sysrq_get_key_op() is no longer used externally, let's make it
a static function.
This patch will allow us to limit access to each and every sysrq op and
constify the sysrq handling.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-kernel@vger.kernel.org
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: linux-alpha@vger.kernel.org
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://lore.kernel.org/r/20200513214351.2138580-1-emil.l.velikov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No other functions use the return value of mxser_change_speed() and the
return value is always 0 now. Make it return void. This fixes the
following coccicheck warning:
drivers/tty/mxser.c:645:5-8: Unneeded variable: "ret". Return "0" on
line 650
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200506061735.19369-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.
Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.
Fixes: 81bb549fdf ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to uart_add_one_port() in serial8250_register_8250_port()
fails, a half-initialized entry in the serial_8250ports[] array is left
behind.
A subsequent reprobe of the same serial port causes that entry to be
reused. Because uart->port.dev is set, uart_remove_one_port() is called
for the half-initialized entry and bails out with an error message:
bcm2835-aux-uart 3f215040.serial: Removing wrong port: (null) != (ptrval)
The same happens on failure of mctrl_gpio_init() since commit
4a96895f74 ("tty/serial/8250: use mctrl_gpio helpers").
Fix by zeroing the uart->port.dev pointer in the probe error path.
The bug was introduced in v2.6.10 by historical commit befff6f5bf5f
("[SERIAL] Add new port registration/unregistration functions."):
https://git.kernel.org/tglx/history/c/befff6f5bf5f
The commit added an unconditional call to uart_remove_one_port() in
serial8250_register_port(). In v3.7, commit 835d844d1a ("8250_pnp:
do pnp probe before legacy probe") made that call conditional on
uart->port.dev which allows me to fix the issue by zeroing that pointer
in the error path. Thus, the present commit will fix the problem as far
back as v3.7 whereas still older versions need to also cherry-pick
835d844d1a.
Fixes: 835d844d1a ("8250_pnp: do pnp probe before legacy probe")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v2.6.10
Cc: stable@vger.kernel.org # v2.6.10: 835d844d1a28: 8250_pnp: do pnp probe before legacy
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/b4a072013ee1a1d13ee06b4325afb19bda57ca1b.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warn the upper layer when n_gms is ready to receive data
again. Without this the associated virtual tty remains blocked
indefinitely.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-4-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For at least some modems like the TELIT LE910, skipping SOF makes
transfers blocking indefinitely after a short amount of data
transferred.
Given the small improvement provided by skipping the SOF (just one
byte on about 100 bytes), it seems better to completely remove this
"feature" than make it optional.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20200512115323.1447922-3-gregory.clement@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace contents of EXAR_DEVICE() with former one.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200512140252.67631-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STM32 UART controllers have the built in modem control support using
dedicated gpios which can be enabled using 'st,hw-flow-ctrl' flag in DT.
But there might be cases where the board design need to use different
gpios for modem control.
For supporting such cases, this commit adds modem control gpio support
to STM32 UART controller using mctrl_gpio driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20200420170204.24541-3-mani@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some variants of the samsung tty driver can pick which clock
to use for their baud rate generation. In the DT conversion,
a default clock was selected to be used if a specific one wasn't
assigned and then a comparison of which clock rate worked better
was done. Unfortunately, the comparison was implemented in such
a way that only the default clock was ever actually compared.
Fix this by iterating through all possible clocks, except when a
specific clock has already been picked via clk_sel (which is
only possible via board files).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/BN6PR04MB06604E63833EA41837EBF77BA3A30@BN6PR04MB0660.namprd04.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e2bd1dcbe1.
In discussion on the mailing list, it has been determined that this is
not the correct type of fix for this issue. Revert it so that we can do
this correctly.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Cc: Raghavendra Rao Ananta <rananta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are 3 small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXrVmRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymY+ACfelBeBAxlYjuvZ8QpDYSkR9fl8EIAoKeuJocX
TaXtUFCvCSax68siL81w
=L0Rp
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are three small TTY/Serial/VT fixes for 5.7-rc5:
- revert for the bcm63xx driver "fix" that was incorrect
- vt unicode console bugfix
- xilinx_uartps console driver fix
All of these have been in linux next with no reported issues"
* tag 'tty-5.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: xilinx_uartps: Fix missing id assignment to the console
vt: fix unicode console freeing with a common interface
Revert "tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart"
Support 32-bit access for the TX/RX hold registers UTXH and URXH.
This is required for some newer SoCs.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-3-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch change the name of macro for general usage.
Signed-off-by: Hyunki Koo <hyunki00.koo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested on Odroid HC1 (Exynos5422):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200506080242.18623-1-hyunki00.koo@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3d9231e698
Rajendra writes:
Greg, there are other patches in the series which have a
dependency on this patch [1] would it be possible for you to
drop this patch and instead ack it so it can be taken via the
msm tree?
So dropping it from here.
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valentine reported seeing:
[ 3.626638] INFO: trying to register non-static key.
[ 3.626639] the code is fine but needs lockdep annotation.
[ 3.626640] turning off the locking correctness validator.
[ 3.626644] CPU: 7 PID: 51 Comm: kworker/7:1 Not tainted 5.7.0-rc2-00115-g8c2e9790f196 #116
[ 3.626646] Hardware name: HiKey960 (DT)
[ 3.626656] Workqueue: events deferred_probe_work_func
[ 3.632476] sd 0:0:0:0: [sda] Optimal transfer size 8192 bytes not a multiple of physical block size (16384 bytes)
[ 3.640220] Call trace:
[ 3.640225] dump_backtrace+0x0/0x1b8
[ 3.640227] show_stack+0x20/0x30
[ 3.640230] dump_stack+0xec/0x158
[ 3.640234] register_lock_class+0x598/0x5c0
[ 3.640235] __lock_acquire+0x80/0x16c0
[ 3.640236] lock_acquire+0xf4/0x4a0
[ 3.640241] _raw_spin_lock_irqsave+0x70/0xa8
[ 3.640245] uart_add_one_port+0x388/0x4b8
[ 3.640248] pl011_register_port+0x70/0xf0
[ 3.640250] pl011_probe+0x184/0x1b8
[ 3.640254] amba_probe+0xdc/0x180
[ 3.640256] really_probe+0xe0/0x338
[ 3.640257] driver_probe_device+0x60/0xf8
[ 3.640259] __device_attach_driver+0x8c/0xd0
[ 3.640260] bus_for_each_drv+0x84/0xd8
[ 3.640261] __device_attach+0xe4/0x140
[ 3.640263] device_initial_probe+0x1c/0x28
[ 3.640265] bus_probe_device+0xa4/0xb0
[ 3.640266] deferred_probe_work_func+0x7c/0xb8
[ 3.640269] process_one_work+0x2c0/0x768
[ 3.640271] worker_thread+0x4c/0x498
[ 3.640272] kthread+0x14c/0x158
[ 3.640275] ret_from_fork+0x10/0x1c
Which seems to be due to the fact that after allocating the uap
structure, nothing initializes the spinlock.
Its a little confusing, as uart_port_spin_lock_init() is one
place where the lock is supposed to be initialized, but it has
an exception for the case where the port is a console.
This makes it seem like a deeper fix is needed to properly
register the console, but I'm not sure what that entails, and
Andy suggested that this approach is less invasive.
Thus, this patch resolves the issue by initializing the spinlock
in the driver, and resolves the resulting warning.
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Reported-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-and-tested-by: Valentin Schneider <valentin.schneider@arm.com>
Link: https://lore.kernel.org/r/20200428184050.6501-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
geni serial needs to express a perforamnce state requirement on CX
powerdomain depending on the frequency of the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: linux-serial@vger.kernel.org
Link: https://lore.kernel.org/r/1588507469-31889-2-git-send-email-rnayak@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When serial console has been assigned to ttyPS1 (which is serial1 alias)
console index is not updated property and pointing to index -1 (statically
initialized) which ends up in situation where nothing has been printed on
the port.
The commit 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console
and driver structures"") didn't contain this line which was removed by
accident.
Fixes: 18cc7ac8a2 ("Revert "serial: uartps: Register own uart console and driver structures"")
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ed3111533ef5bd342ee5ec504812240b870f0853.1588602446.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By directly using kfree() in different places we risk missing one if
it is switched to using vfree(), especially if the corresponding
vmalloc() is hidden away within a common abstraction.
Oh wait, that's exactly what happened here.
So let's fix this by creating a common abstraction for the free case
as well.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reported-by: syzbot+0bfda3ade1ee9288a1be@syzkaller.appspotmail.com
Fixes: 9a98e7a80f ("vt: don't use kmalloc() for the unicode screen buffer")
Cc: <stable@vger.kernel.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2005021043110.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 580d952e44 ("tty:
serial: bcm63xx: fix missing clk_put() in bcm63xx_uart") because we
should not be doing a clk_put() if we were not successful in getting a
valid clock reference via clk_get() in the first place.
Fixes: 580d952e44 ("tty: serial: bcm63xx: fix missing clk_put() in bcm63xx_uart")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200501013904.1394-1-f.fainelli@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This tag contains a handful of fixes that I'd like to target for 5.7.
Specifically:
* The change of a linker argument to allow linking with lld.
* A build fix for configurations without a frame pointer.
* A handful of build fixes related the SBI 0.1 vs 0.2 split.
* The removal of STRICT_KERNEL_RWX for !MMU, which isn't useful
-----BEGIN PGP SIGNATURE-----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=MtxP
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"A handful of fixes.
Specifically:
- fix linker argument to allow linking with lld
- build fix for configurations without a frame pointer
- a handful of build fixes related the SBI 0.1 vs 0.2 split
- remove STRICT_KERNEL_RWX for !MMU, which isn't useful"
* tag 'riscv-for-linus-5.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: select ARCH_HAS_STRICT_KERNEL_RWX only if MMU
riscv: sbi: Fix undefined reference to sbi_shutdown
tty: riscv: Using RISCV_SBI_V01 instead of RISCV_SBI
riscv: sbi: Correct sbi_shutdown() and sbi_clear_ipi() export
riscv: fix vdso build with lld
RISC-V: stacktrace: Declare sp_in_global outside ifdef
Potentially, hvc_open() can be called in parallel when two tasks calls
open() on /dev/hvcX. In such a scenario, if the hp->ops->notifier_add()
callback in the function fails, where it sets the tty->driver_data to
NULL, the parallel hvc_open() can see this NULL and cause a memory abort.
Hence, serialize hvc_open and check if tty->private_data is NULL before
proceeding ahead.
The issue can be easily reproduced by launching two tasks simultaneously
that does nothing but open() and close() on /dev/hvcX.
For example:
$ ./simple_open_close /dev/hvc0 & ./simple_open_close /dev/hvc0 &
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Link: https://lore.kernel.org/r/20200428032601.22127-1-rananta@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20200427122415.47416-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No users of hvcs_driver_string, remove it. This fixes the following gcc
warning:
drivers/tty/hvc/hvcs.c:199:19: warning: ‘hvcs_driver_string’ defined but
not used [-Wunused-const-variable=]
static const char hvcs_driver_string[]
^~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200403071325.3721-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the following messages are seen when booting i.MX8QXP:
fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA (-19)
fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA (-19)
It is not really useful to have such messages on every boot, so change
them to debug level instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200416153453.18825-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
num_chan in register_PCI is used only as an alias for ports_per_aiop. So
drop num_chan and use ports_per_aiop directly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200417105959.15201-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
init_r_port can access pc104 array out of bounds. pc104 is a 2D array
defined to have 4 members. Each member has 8 submembers.
* we can have more than 4 (PCI) boards, i.e. [board] can be OOB
* line is not modulo-ed by anything, so the first line on the second
board can be 4, on the 3rd 12 or alike (depending on previously
registered boards). It's zero only on the first line of the first
board. So even [line] can be OOB, quite soon (with the 2nd registered
board already).
This code is broken for ages, so just avoid the OOB accesses and don't
try to fix it as we would need to find out the correct line number. Use
the default: RS232, if we are out.
Generally, if anyone needs to set the interface types, a module parameter
is past the last thing that should be used for this purpose. The
parameters' description says it's for ISA cards anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/20200417105959.15201-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes below error reported by coccicheck
drivers/tty/serial/bcm63xx_uart.c:848:2-8: ERROR: missing clk_put;
clk_get on line 842 and execution via conditional on line 846
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587472306-105155-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in vc_do_resize() bounds the memory allocation size to avoid
exceeding MAX_ORDER down the kzalloc() call chain and generating a
runtime warning triggerable from user space. However, not only is it
unwise to use a literal value here, but MAX_ORDER may also be
configurable based on CONFIG_FORCE_MAX_ZONEORDER.
Let's use KMALLOC_MAX_SIZE instead.
Note that prior commit bb1107f7c6 ("mm, slab: make sure that
KMALLOC_MAX_SIZE will fit into MAX_ORDER") the KMALLOC_MAX_SIZE value
could not be relied upon.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003281702410.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
breaks the UART on Cubieboard7-lite (based on S700 SoC), This is due to the
fact that generic clk routine clk_disable_unused() disables the gate clks,
and that in turns disables OWL UART (but UART driver never enables it). To
prove this theory, Andre suggested to use "clk_ignore_unused" in kernel
commnd line and it worked (Kernel happily lands into RAMFS world :)).
This commit fix this up by adding clk_prepare_enable().
Fixes: 8ba92cf593 ("arm64: dts: actions: s700: Add Clock Management Unit")
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1587067917-1400-1-git-send-email-amittomer25@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the actual screen size is bounded in vc_do_resize(), the unicode
buffer is still a little more than twice the size of the glyph buffer
and may exceed MAX_ORDER down the kmalloc() path. This can be triggered
from user space.
Since there is no point having a physically contiguous buffer here,
let's avoid the above issue as well as reducing pressure on high order
allocations by using vmalloc() instead.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Cc: <stable@vger.kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.2003282214210.2671@knanqh.ubzr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As shown in SBI v0.2, the legacy console SBI functions (sbi_console_getchar()
and sbi_console_putchar()) are expected to be deprecated; they have no replacement.
Let's HVC_RISCV_SBI and SERIAL_EARLYCON_RISCV_SBI depends on RISCV_SBI_V01.
Fixes: efca139892 ("RISC-V: Introduce a new config for SBI v0.1")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
For SCIF and HSCIF interfaces the SCxSR register holds the status of
data that is to be read next from SCxRDR register, But where as for
SCIFA and SCIFB interfaces SCxSR register holds status of data that is
previously read from SCxRDR register.
This patch makes sure the status register is read depending on the port
types so that errors are caught accordingly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kazuhiro Fujita <kazuhiro.fujita.jg@renesas.com>
Signed-off-by: Hao Bui <hao.bui.yg@renesas.com>
Signed-off-by: KAZUMI HARADA <kazumi.harada.rh@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1585333048-31828-1-git-send-email-kazuhiro.fujita.jg@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Sparc HV console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Link: https://lore.kernel.org/r/20200402172026.79478-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of accessing the registers and checking for tx_empty,
use cdns_uart_tx_empty in cdns_uart_console_write function.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-3-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some platforms, the log is corrupted while console is being
registered. It is observed that when set_termios is called, there
are still some bytes in the FIFO to be transmitted.
So, wait for tx_empty inside cdns_uart_console_setup before calling
set_termios.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/1586413563-29125-2-git-send-email-raviteja.narayanam@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's put it to a separate function, named vc_selection_store_chars.
Again, this makes vc_do_selection a bit shorter and more readable.
Having 4 local variables instead of 12 (5.6-rc1) looks much better now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200415093608.10348-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle these actions:
* poking console
* TIOCL_SELCLEAR
* TIOCL_SELMOUSEREPORT
* start/end precomputation
* clear_selection if the console changed
in a separate function, thus making __set_selection_kernel way shorter
and more readable. The function still needs dissection, but we are
approaching.
This includes introduction of vc_selection and renaming
__set_selection_kernel to vc_do_selection.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200415093608.10348-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sh-sci.h file includes the legacy <linux/gpio.h> header
but the driver is actually migrated to use the mctrl_gpio
library so this is not needed.
Cc: George G. Davis <george_davis@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200415180250.221762-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable i is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed. Also rename i to ret as this new
name makes makes more sense.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200405135423.383466-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coverity reports the following:
var_compare_op: Comparing chan to null implies that chan might be null.
1234 if (chan)
1235 dmaengine_terminate_all(chan);
1236
Dereference after null check (FORWARD_NULL)
var_deref_op: Dereferencing null pointer chan.
1237 dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);
Technically, this is correct. But lpuart_dma_rx_free() is guarded by
lpuart_dma_rx_use which is only true if there is a dma channel, see
lpuart_rx_dma_startup(). In any way, this looks bogus. So remove
the superfluous "if (chan)" check and make coverity happy.
Fixes: a092ab25fd ("tty: serial: fsl_lpuart: fix DMA mapping")
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200403174942.9594-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the OMAP serial driver to use a GPIO descriptor
for the optional RTS signal.
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415183927.269445-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver includes <linux/gpio.h> but does not use any symbols
from the file so drop this include.
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415184300.269889-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- A large series from Nick for 64-bit to further rework our exception vectors,
and rewrite portions of the syscall entry/exit and interrupt return in C. The
result is much easier to follow code that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had become badly
intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings from the
workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and update the
status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to:
Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen Zhou, Christophe JAILLET,
Christophe Leroy, Christoph Hellwig, Clement Courbet, Daniel Axtens, David
Gibson, Douglas Miller, Fabiano Rosas, Fangrui Song, Ganesh Goudar, Gautham R.
Shenoy, Greg Kroah-Hartman, Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie
Halip, Jan Kara, Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger,
Laurentiu Tudor, Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira,
Michael Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat, Rasmus Villemoes, Ravi
Bangoria, Roman Bolshakov, Sam Bobroff, Sandipan Das, Santosh S, Sedat Dilek,
Segher Boessenkool, Shilpasri G Bhat, Sourabh Jain, Srikar Dronamraju, Stephen
Rothwell, Tyrel Datwyler, Vaibhav Jain, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ARdm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Slightly late as I had to rebase mid-week to insert a bug fix:
- A large series from Nick for 64-bit to further rework our exception
vectors, and rewrite portions of the syscall entry/exit and
interrupt return in C. The result is much easier to follow code
that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had
become badly intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings
from the workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and
update the status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to: Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew
Donnellan, Aneesh Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen
Zhou, Christophe JAILLET, Christophe Leroy, Christoph Hellwig, Clement
Courbet, Daniel Axtens, David Gibson, Douglas Miller, Fabiano Rosas,
Fangrui Song, Ganesh Goudar, Gautham R. Shenoy, Greg Kroah-Hartman,
Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie Halip, Jan Kara,
Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger, Laurentiu Tudor,
Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh Salgaonkar,
Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira, Michael
Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat,
Rasmus Villemoes, Ravi Bangoria, Roman Bolshakov, Sam Bobroff,
Sandipan Das, Santosh S, Sedat Dilek, Segher Boessenkool, Shilpasri G
Bhat, Sourabh Jain, Srikar Dronamraju, Stephen Rothwell, Tyrel
Datwyler, Vaibhav Jain, YueHaibing"
* tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc: Make setjmp/longjmp signature standard
powerpc/cputable: Remove unnecessary copy of cpu_spec->oprofile_type
powerpc: Suppress .eh_frame generation
powerpc: Drop -fno-dwarf2-cfi-asm
powerpc/32: drop unused ISA_DMA_THRESHOLD
powerpc/powernv: Add documentation for the opal sensor_groups sysfs interfaces
selftests/powerpc: Fix try-run when source tree is not writable
powerpc/vmlinux.lds: Explicitly retain .gnu.hash
powerpc/ptrace: move ptrace_triggered() into hw_breakpoint.c
powerpc/ptrace: create ppc_gethwdinfo()
powerpc/ptrace: create ptrace_get_debugreg()
powerpc/ptrace: split out ADV_DEBUG_REGS related functions.
powerpc/ptrace: move register viewing functions out of ptrace.c
powerpc/ptrace: split out TRANSACTIONAL_MEM related functions.
powerpc/ptrace: split out SPE related functions.
powerpc/ptrace: split out ALTIVEC related functions.
powerpc/ptrace: split out VSX related functions.
powerpc/ptrace: drop PARAMETER_SAVE_AREA_OFFSET
powerpc/ptrace: drop unnecessary #ifdefs CONFIG_PPC64
powerpc/ptrace: remove unused header includes
...
Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some reverts
to resolve some reported issues. All is now clean with no reported
problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the last
two reverts, all is calm and good.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodfvA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynzCQCfROhar3E8EhYEqSOP6xq6uhX9uegAnRgGY2rs
rN4JJpOcTddvZcVlD+vo
=ocWk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Commit 7f9803072f ("serial: 8250: Support console on software emulated
rs485 ports") amended serial8250_console_write() with rs485 support, but
positioned the invocation of ->rs485_stop_tx() after re-enablement of
interrupts. The irq handler and ->console_write() are serialized with
the port spinlock, so no problem there, but due to the rs485 delay, the
irq handler may unnecessarily spin for a while. Avoid that by moving
->rs485_stop_tx() before re-enablement of interrupts, which also mirrors
the order at the beginning of serial8250_console_write().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/019839cb1f61b01210b6ff9ac9f9079ca77f8411.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a silly copy-paste mistake, commit 7f9803072f ("serial: 8250:
Support console on software emulated rs485 ports") erroneously pauses
for the duration of delay_rts_before_send after writing to the console,
instead of delay_rts_after_send. Mea culpa.
Fixes: 7f9803072f ("serial: 8250: Support console on software emulated rs485 ports")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/9dd67f33c90d23f7fafa3b81b1e812ddabf9ca24.1585319447.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
fd = open("/dev/tty10", O_RDONLY);
for (nproc = 1; nproc < 8; nproc *= 2)
fork();
for (;;) {
sprintf(ttyname, "/dev/tty%d", rand() % 8);
close(open(ttyname, O_RDONLY));
ioctl(fd, VT_GETSTATE, &state);
}
}
KASAN report:
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
CPU: 0 PID: 132 Comm: syz-vt2 Not tainted 5.6.0-rc5-00130-g089b6d3654916 #13
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Allocated by task 136:
[...]
kzalloc include/linux/slab.h:669 [inline]
alloc_tty_struct+0x96/0x8a0 drivers/tty/tty_io.c:2982
tty_init_dev+0x23/0x350 drivers/tty/tty_io.c:1334
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 41:
[...]
kfree+0xbf/0x200 mm/slab.c:3757
free_tty_struct+0x8d/0xb0 drivers/tty/tty_io.c:177
release_one_tty+0x22d/0x2f0 drivers/tty/tty_io.c:1468
process_one_work+0x7f1/0x14b0 kernel/workqueue.c:2264
worker_thread+0x8b/0xc80 kernel/workqueue.c:2410
[...]
Fixes: 4001d7b7fc ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
Reproducer:
#include <fcntl.h>
#include <linux/vt.h>
#include <sys/ioctl.h>
#include <unistd.h>
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
CPU: 0 PID: 129 Comm: syz_vt Not tainted 5.6.0-rc2 #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20191223_100556-anatol 04/01/2014
Call Trace:
[...]
con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
release_tty+0xa8/0x410 drivers/tty/tty_io.c:1514
tty_release_struct+0x34/0x50 drivers/tty/tty_io.c:1629
tty_release+0x984/0xed0 drivers/tty/tty_io.c:1789
[...]
Allocated by task 129:
[...]
kzalloc include/linux/slab.h:669 [inline]
vc_allocate drivers/tty/vt/vt.c:1085 [inline]
vc_allocate+0x1ac/0x680 drivers/tty/vt/vt.c:1066
con_install+0x4d/0x3f0 drivers/tty/vt/vt.c:3229
tty_driver_install_tty drivers/tty/tty_io.c:1228 [inline]
tty_init_dev+0x94/0x350 drivers/tty/tty_io.c:1341
tty_open_by_driver drivers/tty/tty_io.c:1987 [inline]
tty_open+0x3ca/0xb30 drivers/tty/tty_io.c:2035
[...]
Freed by task 130:
[...]
kfree+0xbf/0x1e0 mm/slab.c:3757
vt_disallocate drivers/tty/vt/vt_ioctl.c:300 [inline]
vt_ioctl+0x16dc/0x1e30 drivers/tty/vt/vt_ioctl.c:818
tty_ioctl+0x9db/0x11b0 drivers/tty/tty_io.c:2660
[...]
Fixes: 4001d7b7fc ("vt: push down the tty lock so we can see what is left to tackle")
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kbuild-test reported an error:
config: mips-randconfig-a001-20200321 ...
>> drivers/tty/serial/sprd_serial.c:1175: undefined reference
to `clk_set_parent'
Because some mips Kconfig selects HAVE_CLK but not COMMON_CLK and no
clk_set_parent implemented, so the error was exposed. So adding
dependence on COMMON_CLK can fix this issue.
Fixes: 7ba87cfec7 ("tty: serial: make SERIAL_SPRD not depend on ARCH_SPRD")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200325081427.20312-1-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of lpuart_dma_tx_request() is an negative errno on
failure and zero on success.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move dma_request_chan() out of the atomic context. First this call
should not be in the atomic context at all and second the
dev_info_once() may cause a hang because because the console takes this
spinlock, too.
Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitons in the dt-binding's gpio header only contains some
constants to be used in device trees. It is not relevant for omap-serial
(as the gpio API hides the details) and in fact unused so it can just be
dropped.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200321204031.30369-1-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART on K3 SoCs has configurable RX timeout behavior (controlled via
EFR2) and better DMA integration. This allows to transfer as larger
amount data per DMA transfer compared to older SoCs. Add support for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-7-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per Advisory 27 of AM437x Silicon errata document, Spurious UART
interrupts may occur when DMA mode (FCR.DMA_MODE) is enabled. The
Interrupt Controller flags that a UART interrupt has occurred; however,
the associated IT_PENDING bit remains set to 1, indicating that no
interrupt is pending. Acknowledge the spurious interrupts for every
occurrence as workaround.
Errata is applicable to all TI SoCs with this IP.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-6-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although same 8250 compliant UART IP is reused across different SoC,
their integration wrt DMA varies greatly across SoCs. Therefore,
different SoC may need to use different FIFO trigger level for DMA
event and DMA configuration parameters. Provide a way to pass this
information via driver data. This is required to support UART DMA on
AM654/J721e SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-5-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Caller functions of __dma_rx_do_complete() already hold rx_dma_lock.
Therefore move locking out of the function to avoid need to release and
reacquire lock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-4-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take into account data stuck in DMA internal buffers before pushing data
to higher layer. dma_tx_state has "in_flight_bytes" member that provides
this information.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call stop_rx() to halt reception when throttle is requested. Update
unthrottle callback to restart reception.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-3-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.
Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that all bytes are transmitted out of Uart by monitoring
CDNS_UART_SR_TACTIVE bit as well.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/e2514818af5973be291cc117d07739f068b71639.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_termios function should not wait for the transmit FIFO empty
(CDNS_UART_SR_TXEMPTY) unconditionally. The tty layer takes care
of it based on the parameter passed (TCSANOW/TCSADRAIN/TCSAFLUSH).
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/536e190dd5bbb474007a67e6323c048288942a28.1584610774.git.shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7765435030 ("take compat TIOC[SG]SERIAL treatment into
tty_compat_ioctl()") changed the compat version of TIOCGSERIAL to start
checking for the presence of the ->set_serial function pointer rather
than ->get_serial. This appears to be a copy-and-paste error, since
->get_serial is the function pointer that is called as well as the
pointer that is checked by the non-compat version of TIOCGSERIAL.
Fix this by checking the correct function pointer.
Fixes: 7765435030 ("take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200224182044.234553-3-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7765435030 ("take compat TIOC[SG]SERIAL treatment into
tty_compat_ioctl()") changed the compat version of TIOCGSERIAL to start
copying a whole 'serial_struct32' to userspace rather than individual
fields, but failed to initialize all padding and fields -- namely the
hole after the 'iomem_reg_shift' field, and the 'reserved' field.
Fix this by initializing the struct to zero.
[v2: use sizeof, and convert the adjacent line for consistency.]
Reported-by: syzbot+8da9175e28eadcb203ce@syzkaller.appspotmail.com
Fixes: 7765435030 ("take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()")
Cc: <stable@vger.kernel.org> # v4.20+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200224182044.234553-2-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current version of the TTY code unlocks the tty_struct(s) before
release_tty() rather than after. Moreover, tty_unlock_pair() no longer
exists. Thus, remove the outdated comments regarding tty_unlock_pair().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224073359.292795-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to Kernel driver API to route trace data.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200302143642.GA3335@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to the HVC driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200301170419.GA7125@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Also rewrite the code in a standard if-form instead of ugly
conditional operators.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092905.24362-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200311092930.24433-1-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need to cleanup sprd_port anymore, since we've dropped the way
of using the sprd_port[] array to get port index.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies the process of getting serial port number, with
this patch, serial devices must have aliases configured in devicetree.
The serial port searched out via sprd_port array maybe wrong if we don't
have serial alias defined in devicetree, and specify console with command
line, we would get the wrong port number if other serial ports probe
failed before console's. So using aliases is mandatory.
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200318105049.19623-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It would be too tricky and error prone to allow DMA operations on
kernel console.
One of the concern is when DMA is a separate device, for example on
Intel CherryTrail platforms, and might need special work around to be
functional, see the commit
eebb3e8d8a ("ACPI / LPSS: override power state for LPSS DMA device")
for more information.
Another one is that kernel console is used in atomic context, e.g.
when printing crucial information to the user (Oops or crash),
and DMA may not serve due to power management complications
including non-atomic ACPI calls but not limited to it (see above).
Besides that, other concerns are described in the commit
84b40e3b57 ("serial: 8250: omap: Disable DMA for console UART")
done for OMAP UART and may be repeated here.
Disable any kind of DMA operations on kernel console due to above concerns.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-7-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing any kind of power management for kernel console is really bad idea.
First of all, it runs in poll and atomic mode. This fact attaches a limitation
on the functions that might be called. For example, pm_runtime_get_sync() might
sleep and thus can't be used. This call needs, for example, to bring the device
to powered on state on the system, where the power on sequence may require
on-atomic operations, such as Intel Cherrytrail with ACPI enumerated UARTs.
That said, on ACPI enabled platforms it might even call firmware for a job.
On the other hand pm_runtime_get() doesn't guarantee that device will become
powered on fast enough.
Besides that, imagine the case when console is about to print a kernel Oops and
it's powered off. In such an emergency case calling the complex functions is
not the best what we can do, taking into consideration that user wants to see
at least something of the last kernel word before it passes away.
Here we modify the 8250 console code to prevent runtime power management.
Note, there is a behaviour change for OMAP boards. It will require to detach
kernel console to become idle.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the future we would like to disable power management on the serial devices
used as kernel consoles to avoid weird behaviour in some cases. However,
disabling PM may prevent system to go to deep sleep states, which in its turn
leads to the higher power consumption.
Tony Lindgren proposed a work around, i.e. allow user to detach such consoles
to make PM working again. In case user wants to see what's going on, it also
provides a mechanism to attach console back.
Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 175b558d0e.
When the user configures a kernel without support for Samsung SoCs, it
makes no sense to ask the user about enabling "Samsung SoC serial
support", as Samsung serial ports can only be found on Samsung SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200306102301.16870-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should validate if the 'sup' is NULL or not before freeing DMA
memory, to fix below warning.
"drivers/tty/serial/sprd_serial.c:1141 sprd_remove()
error: we previously assumed 'sup' could be null (see line 1132)"
Fixes: f4487db58e ("serial: sprd: Add DMA mode support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lanqing Liu <liuhhome@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e2bd92691538e95b04a2c2a728f3292e1617018f.1584325957.git.liuhhome@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function sprd_console_setup() would be called from .probe() which can
be called after freeing __init functions, for example the .probe() would
return -EPROBE_DEFER since it depends on clock modules.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-3-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPRD serial driver need to know which serial port would be used as
console in an early period during initialization, the purpose is to
keep the console port alive as possible even if there's some error
caused by no clock configured under serial devicetree nodes. But with
the patch [1], the console port couldn't be identified if missing
console command line.
So this patch adds using another interface to do check by reading
stdout-path.
[1] https://lore.kernel.org/lkml/20190826072929.7696-4-zhang.lyra@gmail.com/
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200316101930.9962-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ev_byte_channel_send() assumes that its third argument is a 16 byte
array. Some places where it is called it may not be (or we can't
easily tell if it is). Newer compilers have started producing warnings
about this, so make sure we actually pass a 16 byte array.
There may be more elegant solutions to this, but the driver is quite
old and hasn't been updated in many years.
The warnings (from a powerpc allyesconfig build) are:
In file included from include/linux/byteorder/big_endian.h:5,
from arch/powerpc/include/uapi/asm/byteorder.h:14,
from include/asm-generic/bitops/le.h:6,
from arch/powerpc/include/asm/bitops.h:250,
from include/linux/bitops.h:29,
from include/linux/kernel.h:12,
from include/asm-generic/bug.h:19,
from arch/powerpc/include/asm/bug.h:109,
from include/linux/bug.h:5,
from include/linux/mmdebug.h:5,
from include/linux/gfp.h:5,
from include/linux/slab.h:15,
from drivers/tty/ehv_bytechan.c:24:
drivers/tty/ehv_bytechan.c: In function ‘ehv_bc_udbg_putc’:
arch/powerpc/include/asm/epapr_hcalls.h:298:20: warning: array subscript 1 is outside array bounds of ‘const char[1]’ [-Warray-bounds]
298 | r6 = be32_to_cpu(p[1]);
include/uapi/linux/byteorder/big_endian.h:40:51: note: in definition of macro ‘__be32_to_cpu’
40 | #define __be32_to_cpu(x) ((__force __u32)(__be32)(x))
| ^
arch/powerpc/include/asm/epapr_hcalls.h:298:7: note: in expansion of macro ‘be32_to_cpu’
298 | r6 = be32_to_cpu(p[1]);
| ^~~~~~~~~~~
drivers/tty/ehv_bytechan.c:166:13: note: while referencing ‘data’
166 | static void ehv_bc_udbg_putc(char c)
| ^~~~~~~~~~~~~~~~
Fixes: dcd83aaff1 ("tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Trim warnings from change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200109183912.5fcb52aa@canb.auug.org.au
Shift cases one level left. This makes the code more readable and some
lines need not wrap anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200316065911.11024-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a helper called rounddown for these modulo computations. So use
it.
No functional change intended and "objdump -d" proves that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200316065911.11024-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of awkward ternary operator with comparison, use simple min()
for blankinterval and vesa_off_interval.
No functional change intended and "objdump -d" proves that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200316065911.11024-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Joe suggests, dynamic debug can print module name and line number
along with message. So remove __FILE__ and __LINE__ from all those
pr_debug calls.
Out of curiosity, I measured the savings, 200 bytes of code are gone.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Suggested-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/20200316064910.4941-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The merge commit cb05c6c82f (Merge 5.6-rc5 into tty-next) introduced a
double lock to set_selection_kernel. vc_sel.lock is locked both in
set_selection_kernel and its callee __set_selection_kernel now.
Remove the latter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20200316064544.4799-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The geni serial driver's shutdown code had a special case to call
console_stop(). Grepping through the code, it was the only serial
driver doing something like this (the only other caller of
console_stop() was in serial_core.c).
As far as I can tell there's no reason to call console_stop() in the
geni code. ...and a good reason _not_ to call it. Specifically if
you have an agetty running on the same serial port as the console then
killing the agetty kills your console and if you start the agetty
again the console doesn't come back.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200313134635.2.I3648fac6c98b887742934146ac2729ecb7232eb1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a board using qcom_geni_serial I found that I could no longer
interact with kdb if I got a crash after the "agetty" running on the
same serial port was killed. This meant that various classes of
crashes that happened at reboot time were undebuggable.
Reading through the code, I couldn't figure out why qcom_geni_serial
felt the need to run so much code at port shutdown time. All we need
to do is disable the interrupt.
After I make this change then a hardcoded kgdb_breakpoint in some late
shutdown code now allows me to interact with the debugger. I also
could freely close / re-open the port without problems.
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200313134635.1.Icf54c533065306b02b880c46dfd401d8db34e213@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224080326.295046-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The might_sleep() in do_con_write() is redundant because console_lock()
already contains might_sleep(). Remove it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20200224073450.292892-1-ebiggers@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move LDISC_AUTOLOAD ahead of the Serial drivers menu.
Move the Serial drivers menu ahead of the Non-standard serial port
support menu.
Move NOZOMI out of the SERIAL_NONSTANDARD area since it does not
depend on SERIAL_NONSTANDARD and it breaks the SERIAL_NONSTANDARD
menu list.
Alphabetize the remaining drivers (in tty/Kconfig) by their prompt strings.
[The drivers in tty/hvc/Kconfig and tty/serial/Kconfig have not
been alphabetized.]
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20200311225736.32147-4-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'source' (include) all of the tty/*/Kconfig files from
drivers/tty/Kconfig instead of from drivers/char/Kconfig.
This consolidates them both in source code and in menu
presentation to the user.
Move hvc/Kconfig and serial/Kconfig 'source' lines into the
if TTY/endif block and remove the if TTY/endif blocks from
those 2 files.
Cc: linux-serial@vger.kernel.org
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Jiri Slaby <jslaby@suse.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20200311225736.32147-3-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor uart_unlock_and_check_sysrq() to:
- explicitly show that we release a port lock which makes
static analyzers happy:
CHECK drivers/tty/serial/serial_core.c
.../serial_core.c:3290:17: warning: context imbalance in 'uart_unlock_and_check_sysrq' - unexpected unlock
- use flags instead of irqflags to avoid confusion with IRQ flags
- provide one return point
- be more compact
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20200310174337.74109-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in SysRq code instead of open coded variant.
This eliminates the conditional entirely for SERIAL_CORE_CONSOLE=n case.
While here, refactor the conditional to be more compact.
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is useful to see on the serial console the magic sequence itself
to enable SysRq without rummaging source code.
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Compiler is not happy about using ARRAY_SIZE() in comparison to smaller type:
CC drivers/tty/serial/serial_core.o
.../serial_core.c: In function ‘uart_try_toggle_sysrq’:
.../serial_core.c:3222:24: warning: comparison is always false due to limited range of data type [-Wtype-limits]
3222 | if (++port->sysrq_seq < (ARRAY_SIZE(sysrq_toggle_seq) - 1)) {
| ^
Looking at the code it appears that there is an additional weirdness,
i.e. use ARRAY_SIZE() against simple string literal. Yes, the idea probably
was to allow '\0' in the sequence, but it's impractical: kernel configuration
won't accept it to begin with followed by a comment about '\0' before
comparison in question.
Drop all these by switching to strlen() and convert code accordingly.
Note, GCC seems clever enough to calculate string length at compile time.
Fixes: 68af43173d ("serial/sysrq: Add MAGIC_SYSRQ_SERIAL_SEQUENCE")
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200310174337.74109-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix the RX cancel command failure, rx_fifo buffer needs to be
flushed in stop_rx() by calling handle_rx().In handle_rx() the data
in rx_fifo buffer is read and then dropped, not sent to upper layers.
If set_termios is called before startup, by this time memory is not
allocated to port->rx_fifo buffer, which leads to a NULL pointer
dereference.
To avoid this NULL pointer dereference allocate memory to port->rx_fifo
in probe itself.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reported-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1583477228-32231-2-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver for the Intel MID never seems to have been properly
integrated upstream: the platform data in <linux/spi/ifx_modem.h>
is not used anywhere in the kernel and haven't been since it was
merged into the kernel in 2010.
There might be out-of-tree users, so I don't want to delete the
driver, but I will refactor it to use GPIO descriptors, which
means that out-of-tree users will need to adapt.
There are several examples in the kernel of how to provide the
resources necessary for using GPIO descriptors to pass in the
GPIO lines, for the MID platform in particular, it will suffice
to inspect the code in files like:
arch/x86/platform/intel-mid/device_libs/platform_bt.c
This refactoring transfers all GPIOs in the driver, including
a hard-coded "PMU reset" in the driver to use GPIO descriptors
instead.
The following named GPIO descriptors need to be supplied:
- reset
- power
- mrdy
- srdy
- rst_out
- pmu_reset
Cc: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200311083131.693908-2-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The &spi->dev is used so many times that the code gets
visibly better by introducing a simple dev helper variable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200311083131.693908-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a early_console_setup() for the LS1028A SoC with 32bit, little
endian access. If the bootloader does a fixup of the clock-frequency
node the baudrate divisor register will automatically be set.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-5-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LS1028A uses little endian register access and has a different FIFO
size encoding.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-4-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the correct device to request the DMA mapping. Otherwise the IOMMU
doesn't get the mapping and it will generate a page fault.
The error messages look like:
[ 19.012140] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
[ 19.023593] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
This was tested on a custom board with a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA channel might not be available at probe time. This is esp. the
case if the DMA controller has an IOMMU mapping.
There is also another caveat. If there is no DMA controller at all,
dma_request_chan() will also return -EPROBE_DEFER. Thus we cannot test
for -EPROBE_DEFER in probe(). Otherwise the lpuart driver will fail to
probe if, for example, the DMA driver is not enabled in the kernel
configuration.
To workaround this, we request the DMA channel in _startup(). Other
serial drivers do it the same way.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in instead of open coded variant.
Note, SERIAL_CORE_CONSOLE is selected by SERIAL_ATMEL_CONSOLE,
thus no functional changes expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Link: https://lore.kernel.org/r/20200310133057.86840-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use uart_console() helper in instead of open coded variant.
Note, SERIAL_CORE_CONSOLE is selected by SERIAL_PIC32_CONSOLE,
thus no functional changes expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200311090027.64441-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SiFive's UART has a software controller clock divider that produces the
final baud rate clock. Whenever the clock that drives the UART is
changed this divider must be updated accordingly, and given that these
two events are controlled by software they cannot be done atomically.
During the period between updating the UART's driving clock and internal
divider the UART will transmit a different baud rate than what the user
has configured, which will probably result in a corrupted transmission
stream.
The SiFive UART has a FIFO, but due to an issue with the programming
interface there is no way to directly determine when the UART has
finished transmitting. We're essentially restricted to dead reckoning
in order to figure that out: we can use the FIFO's TX busy register to
figure out when the last frame has begun transmission and just delay for
a long enough that the last frame is guaranteed to get out.
As far as the actual implementation goes: I've modified the existing
existing clock notifier function to drain both the FIFO and the shift
register in on PRE_RATE_CHANGE. As far as I know there is no hardware
flow control in this UART, so there's no good way to ask the other end
to stop transmission while we can't receive (inserting software flow
control messages seems like a bad idea here).
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/20200307042637.83728-1-palmer@dabbelt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the vt fixes in here and it resolves a merge issue with
drivers/tty/vt/selection.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark mips_ejtag_fdc_encode() methods switch-case-4 as expecting to
fall through.
This patch fixes the following warning:
drivers/tty/mips_ejtag_fdc.c: In function ‘mips_ejtag_fdc_encode’:
drivers/tty/mips_ejtag_fdc.c:245:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
word.word &= 0x00ffffff;
~~~~~~~~~~^~~~~~~~~~~~~
drivers/tty/mips_ejtag_fdc.c:246:2: note: here
case 3:
^~~~
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Link: https://lore.kernel.org/r/20200306124913.151A68030792@mail.baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many embedded boards have a disconnected TTL level serial which can
generate some garbage that can lead to spurious false sysrq detects.
Currently, sysrq can be either completely disabled for serial console
or always disabled (with CONFIG_MAGIC_SYSRQ_SERIAL), since
commit 732dbf3a61 ("serial: do not accept sysrq characters via serial port")
At Arista, we have such boards that can generate BREAK and random
garbage. While disabling sysrq for serial console would solve
the problem with spurious false sysrq triggers, it's also desirable
to have a way to enable sysrq back.
As a measure of balance between on and off options, add
MAGIC_SYSRQ_SERIAL_SEQUENCE which is a string sequence that can enable
sysrq if it follows BREAK on a serial line. The longer the string - the
less likely it may be in the garbage.
Having the way to enable sysrq was beneficial to debug lockups with
a manual investigation in field and on the other side preventing false
sysrq detections.
Based-on-patch-by: Vasiliy Khoruzhick <vasilykh@arista.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200302175135.269397-3-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many embedded boards have a disconnected TTL level serial which can
generate some garbage that can lead to spurious false sysrq detects.
Currently, sysrq can be either completely disabled for serial console
or always disabled (with CONFIG_MAGIC_SYSRQ_SERIAL), since
commit 732dbf3a61 ("serial: do not accept sysrq characters via serial port")
At Arista, we have such boards that can generate BREAK and random
garbage. While disabling sysrq for serial console would solve
the problem with spurious false sysrq triggers, it's also desirable
to have a way to enable sysrq back.
Having the way to enable sysrq was beneficial to debug lockups with
a manual investigation in field and on the other side preventing false
sysrq detections.
As a preparation to add sysrq_toggle_support() call into uart,
remove a private copy of sysrq_enabled from sysctl - it should reflect
the actual status of sysrq.
Furthermore, the private copy isn't correct already in case
sysrq_always_enabled is true. So, remove __sysrq_enabled and use a
getter-helper sysrq_mask() to check sysrq_key_op enabled status.
Cc: Iurii Zaikin <yzaikin@google.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200302175135.269397-2-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal if data
is transmitted through the tty layer.
Console messages bypass the tty layer and instead are emitted via
serial8250_console_write(). Amend that function to drive RTS as well,
allowing for a console on rs485 ports.
Note that serial8250_console_write() may be called concurrently to the
tty layer accessing the port. The two protect their accesses with the
port lock, but serial8250_console_write() may find RTS still being
asserted by the tty layer, in which case it shouldn't be deasserted
after the console message has been printed. Recognize such situations
by checking the em485->tx_stopped flag.
If a delay_rts_before_send or delay_rts_after_send has been specified,
serial8250_console_write() busy-waits for its duration. Optimizations
for those wait times are conceivable: E.g. if RTS is already asserted,
we could check whether em485->start_tx_timer is active and wait only
for the remaining expire time. But this would require calling into
the hrtimer infrastructure, which involves acquiring locks and
potentially reprogramming timer hardware. Such operations seem too
risky in the context of console printout, which needs to work even when
the kernel has crashed and emits a BUG splat. So I've gone with a
simplistic solution which just always waits for the full delay.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/65edffce4670a19e598015c03cbe46f1ffd93e43.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend 8250_bcm2835aux.c to support rs485 as introduced for 8250_omap.c
by commit e490c9144c ("tty: Add software emulated RS485 support for
8250").
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register: If the bit is clear, RTS is high. With omap, it's
apparently the other way round.
Moreover, omap achieves half-duplex mode by disabling the UART_IER_RDI
interrupt and clearing the RX FIFO when TX stops. This approach doesn't
work on bcm2835aux because the UART_LSR_DR bit is set even when
UART_IER_RDI is disabled. Consequently, serial8250_handle_irq() invokes
serial8250_rx_chars() to empty the FIFO and characters are received even
though the user requested half-duplex. Solve by disabling the receiver
using the non-standard CNTL register.
Cache that register in the driver's private data for performance. Set
the private data pointer before calling serial8250_register_8250_port()
to prevent a null pointer deref in case one of the rs485 callbacks is
invoked immediately after port registration.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/dd86460e20a8f979b7272a0bde73640312b902b1.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
So far the only drivers taking advantage of it are 8250_omap.c and
8250_of.c.
We're about to make use of the feature in 8250_bcm2835aux.c as well.
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register. Moreover, omap achieves half-duplex mode by
disabling the RX interrupt and clearing the RX FIFO when TX stops.
The bcm2835aux requires disabling the receiver instead.
Support these behavioral differences by generalizing the rs485 emulation:
Introduce ->rs485_start_tx() and ->rs485_stop_tx() callbacks in struct
uart_8250_port, provide generic implementations containing the existing
code and use them as callbacks in 8250_omap.c and 8250_of.c.
start_tx_rs485() is idempotent in that it recognizes whether RTS is
already asserted. Achieve the same by introducing a tx_stopped flag in
struct uart_8250_em485. This may even perform a little better on arches
where memory access is faster than mmio access.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/5ac0464ae4414708e723a1e0d52b0c1b2bd41b9b.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When rs485 transmission over an 8250 port stops, __stop_tx() assigns
active_timer = NULL before calling __stop_tx_rs485().
That function in turn either assigns active_timer = stop_tx_timer and
rearms the timer (in case a delay_rts_after_send needs to be observed)
or directly calls __do_stop_tx_rs485().
Move the assignment active_timer = NULL to __stop_tx_rs485() into the
branch which directly calls __do_stop_tx_rs485(), thereby avoiding a
duplicate assignment and simplifying the code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/bca638405550eaf92f0c6060b553b687f35885e0.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amend the generic ->rs485_config() callback to sanitize RTS polarity and
zero-fill the padding (in addition to the existing sanitization of the
RTS delays).
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/ff833721bc372d38678f289eb2a44dbf016d5203.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e490c9144c ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
Drivers opt in to the feature by calling serial8250_em485_init() from
their ->rs485_config() callback.
So far there are two drivers doing that, 8250_omap.c and 8250_of.c.
Both use an identical callback. We're about to add a third user of that
callback, therefore deduplicate it and move it to 8250_port.c.
Drivers now opt in to rs485 software emulation by assigning the generic
serial8250_rs485_config() callback introduced herein to their
.rs485_config struct member. This change allows unexporting
serial8250_em485_init() and declaring it static.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Cc: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/r/fcef63642dc4eae41ae7842d23747b2bf5d40285.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve rs485 devicetree properties on registration of 8250 ports in
case they are attached to an rs485 transceiver.
If the property "linux,rs485-enabled-at-boot-time" is present, invoke
the ->rs485_config() callback to immediately deassert RTS, thereby
ceasing control of the bus.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/5908ea89b7f9da54872d6634b606d83db032297a.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_do_set_mctrl() currently allows modifying the RTS modem
control line even when RTS is used as an rs485 Transmit Enable signal.
It is thus possible for user space to interfere with rs485 communication
by invoking a TIOCMSET ioctl().
Ignore such change requests and retain the current RTS polarity when in
rs485 mode. Note that serial8250_set_mctrl() is always called with
port->lock held, so there's no risk that RTS is changed concurrently.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/b1ce34ca9bc4d7bdc6e9852fcf30b1f4e37c8a80.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a driver exposes early consoles with EARLYCON_DECLARE() and
OF_EARLYCON_DECLARE(), pefer the non-OF variant if the user specifies it
by
earlycon=<driver>,<options>
The rationale behind this is that some drivers register multiple setup
functions under the same driver name. Eg.
OF_EARLYCON_DECLARE(lpuart, "fsl,vf610-lpuart", lpuart_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,ls1021a-lpuart", lpuart32_early_console_setup);
OF_EARLYCON_DECLARE(lpuart32, "fsl,imx7ulp-lpuart", lpuart32_imx_early_console_setup);
EARLYCON_DECLARE(lpuart, lpuart_early_console_setup);
EARLYCON_DECLARE(lpuart32, lpuart32_early_console_setup);
It depends on the order of the entries which console_setup() actually
gets called. To make things worse, I guess it also depends on the
compiler how these are ordered. Thus always prefer the EARLYCON_DECLARE()
ones.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200220174607.24285-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to tty serial drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200301204517.GA10368@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node
dependence") the port line number can also be allocated by IDA, but in
case of an error the ID will no be removed again. More importantly, any
ID will be freed in remove(), even if it wasn't allocated but instead
fetched by of_alias_get_id(). If it was not allocated by IDA there will
be a warning:
WARN(1, "ida_free called for id=%d which is not allocated.\n", id);
Move the ID allocation more to the end of the probe() so that we still
can use plain return in the first error cases.
Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200303174306.6015-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a659652f61.
This broke the earlycon on LS1021A processors because the order of the
earlycon_setup() functions were changed. Before the commit the normal
lpuart32_early_console_setup() was called. After the commit the
lpuart32_imx_early_console_setup() is called instead.
Fixes: a659652f61 ("tty: serial: fsl_lpuart: drop EARLYCON_DECLARE")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200303174306.6015-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Apple devices the _CRS method returns an empty resource template, and
the resource settings are instead provided by the _DSM method. But
commit 33364d63c7 (serdev: Add ACPI
devices by ResourceSource field) changed the search for serdev devices
to require valid, non-empty resource template, thereby breaking Apple
devices and causing bluetooth devices to not be found.
This expands the check so that if we don't find a valid template, and
we're on an Apple machine, then just check for the device being an
immediate child of the controller and having a "baud" property.
Cc: <stable@vger.kernel.org> # 5.5
Fixes: 33364d63c7 ("serdev: Add ACPI devices by ResourceSource field")
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20200211194723.486217-1-ronald@innovation.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the dependency with ARCH_SPRD from sprd serial/console Kconfig-s,
since we want them can be built-in when ARCH_SPRD is set as 'm'.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20200305103228.9686-2-zhang.lyra@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->setup() callback is mandatory for the devices.
Provide it for Elkhart Lake UART ports.
Note, for time being it's empty, but in the future it might require
an additional configuration such as DMA.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200305130822.36850-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MTK uart design no need to control uart clock,
so we just control bus clock in runtime function.
Add uart clock used count to avoid repeatedly switching the clock.
Signed-off-by: Changqi Hu <changqi.hu@mediatek.com>
Link: https://lore.kernel.org/r/1582707225-26815-1-git-send-email-changqi.hu@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The peripheral has support for inverting its input and/or output
signals. This is useful if the hardware flips polarity of the
peripheral's signal, such as swapped +/- pins on an RS-422 transceiver,
or an inverting level shifter. Add support for these control registers
via the device tree binding.
As part of this change, make the writes of the various registers more
uniform by moving the UCR3 block up near the other registers' blocks,
since the INVT bit must be set before enabling the peripheral.
Signed-off-by: George Hilliard <ghilliard@kopismobile.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200226222319.18383-3-ghilliard@kopismobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emulate half-duplex operation and use mctrl_gpio to add support for
RS485 tranceiver with transmit/receive switch hooked to RTS GPIO line.
This is needed to make use of the RS485 port found on Teltonika RUT955.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200221212331.GA21467@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPM UART (PowerPC) has an open coded GPIO modem control
handling. Since I can't test this I can't just migrate it to
the serial mctrl GPIO helper library though I wish I could.
I do second best and convert it to GPIO descriptors at least.
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200229231842.247563-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing in this driver uses the symbols from <linux/gpio.h>
so drop this include.
Cc: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Cc: Songjun Wu <songjun.wu@linux.intel.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200229212331.174946-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing in this driver uses the symbols from these GPIO
includes so drop them. These are probably just historical
artifacts from befor mctrl_gpio was used.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200229220941.205599-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shift the cases one level left as this is how we are supposed to write
the switch-case code according to the CodingStyle.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is declared in vt_kern.h, so no need to declare it in selection.c
which includes the header.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move all the selection global variables to a structure vc_selection,
instantiated as vc_sel. This helps to group all the variables together
and see what should be protected by the embedded lock too.
It might be used later also for per-console selection support.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use_unicode needs not be global. It is used only in set_selection_kernel
and sel_pos (a callee). It is also always set there prior calling
sel_pos. So make use_unicode local and rename it to plain shorter
"unicode". Finally, propagate it to sel_pos via parameter.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
multiplier and mode are not actually needed:
* multiplier is used only in kmalloc_array, so use "use_unicode ? 4 : 1"
directly
* mode is used only to assign a bool in this manner:
if (cond)
x = true;
else
x = false;
So do "x = cond" directly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
in this place, the function should return a
negative value and the PTR_ERR already returns
a negative,so return -PTR_ERR() is wrong.
Signed-off-by: tangbin <tangbin@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200305013823.20976-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to nest the console lock in sel_lock, so we have to push it down
a bit. Fortunately, the callers of set_selection_* just lock the console
lock around the function call. So moving it down is easy.
In the next patch, we switch the order.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 07e6124a1a ("vt: selection, close sel_buffer race")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200228115406.5735-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
drivers/tty/n_tty.c: In function ‘__process_echoes’:
drivers/tty/n_tty.c:657:18: warning: statement will never be executed [-Wswitch-unreachable]
657 | unsigned int num_chars, num_bs;
| ^~~~~~~~~
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Reviewed-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200220062313.69209-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two were macros. Switch them to static inlines, so that it's more
understandable what they are doing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200219073951.16151-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson