Commit Graph

4205 Commits

Author SHA1 Message Date
Laurentiu Tudor 7d99532955 usb: host: ohci-tmio: init genalloc for local memory
In preparation for dropping the existing "coherent" dma mem declaration
APIs, replace the current dma_declare_coherent_memory() based mechanism
with the creation of a genalloc pool that will be used in the OHCI
subsystem as replacement for the DMA APIs.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-06-03 16:00:07 +02:00
Laurentiu Tudor 7d9e6f5aeb usb: host: ohci-sm501: init genalloc for local memory
In preparation for dropping the existing "coherent" dma mem declaration
APIs, replace the current dma_declare_coherent_memory() based mechanism
with the creation of a genalloc pool that will be used in the OHCI
subsystem as replacement for the DMA APIs.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-06-03 16:00:07 +02:00
Laurentiu Tudor b0310c2f09 USB: use genalloc for USB HCs with local memory
For HCs that have local memory, replace the current DMA API usage with
a genalloc generic allocator to manage the mappings for these devices.
To help users, introduce a new HCD API, usb_hcd_setup_local_mem() that
will setup up the genalloc backing up the device local memory. It will
be used in subsequent patches.  This is in preparation for dropping
the existing "coherent" dma mem declaration APIs.  The current
implementation was relying on a short circuit in the DMA API that in
the end, was acting as an allocator for these type of devices.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Tested-by: Fredrik Noring <noring@nocrew.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-06-03 16:00:07 +02:00
Linus Torvalds 22c58fd70c ARM: SoC platform updates
SoC updates, mostly refactorings and cleanups of old legacy platforms.
 Major themes this release:
 
  - Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
  - Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
  - Cleanups of Davinci
 
 This tag also contains a few patches that were queued up as fixes before
 5.1 but I didn't get sent in before release.
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlzc+sMPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3ygQP/3mxLFGJxgHk6m/41V4Tepv9F2ZZ3BW4Lcp7
 vZtr6xiyhZXzIHOGzqQ4VGllfWhMWnjzZZe3iruSBY1gpJU7D4x054T3xVsIDs9F
 EIcbBm5fE0O0bdijfk7V8vBu7LOIP/KYdaD1n9WDhW0Hy4wTXN8NNLSKEU5Lq15p
 oz/A3QP5GcwhGAqaHyxx445La9yEKKWAsc2cOCRCdvfw6+n1GpoE6TI1YGjDvqbw
 xd73mIwXb0l0f7jhCV7OPyZ3t/aQgTD3ddr4gHUGNa8sSWmD5nupSVxj23FkbGby
 ejqJMxOfHpJJGIL/sxmR3+cFBYxyE+JNmrEq/kDW5ncWs/LY91juJxR1dkQKs6Mj
 4Y9CWruftDz34DlFs/J33hF/rdZ73O91ldk7zqND41Fi5aLrIKvZBJlTuqyZ0tGV
 YNRxsjWF953h8TXimDV0KvBgO4+E8d5ype/kIYtEGYO9DVmXQGMxFx2Gt2I/NfoH
 5tCtVFwDPpMxJShpXHLMzUT8sQL3mytg5L/MIPTGx+zAtDwx/qTLEEAElffG29oI
 vdzgJR0lrG/zzqQh25/M80UZYMdOrwtjAB42C+jAvlfQ0C4DtvSH+8OdcROOgj0b
 GbAJbTdHYTD6OpoxhSuRii7zzNxw+i7pQj+uLSt8s8ZReGkUk5a2wpRpoVoV2WxK
 RJHkMK95
 =pUeO
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC platform updates from Olof Johansson:
 "SoC updates, mostly refactorings and cleanups of old legacy platforms.

  Major themes this release:

   - Conversion of ixp4xx to a modern platform (drivers, DT, bindings)

   - Moving some of the ep93xx headers around to get it closer to
     multiplatform enabled.

   - Cleanups of Davinci

  This also contains a few patches that were queued up as fixes before
  5.1 but I didn't get sent in before release"

* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
  ARM: debug-ll: add default address for digicolor
  ARM: u300: regulator: add MODULE_LICENSE()
  ARM: ep93xx: move private headers out of mach/*
  ARM: ep93xx: move pinctrl interfaces into include/linux/soc
  ARM: ep93xx: keypad: stop using mach/platform.h
  ARM: ep93xx: move network platform data to separate header
  ARM: stm32: add AMBA support for stm32 family
  MAINTAINERS: update arch/arm/mach-davinci
  ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
  ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
  soc: ixp4xx: qmgr: Add DT probe code
  soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
  soc: ixp4xx: npe: Add DT probe code
  soc: ixp4xx: Add DT bindings for IXP4xx NPE
  soc: ixp4xx: qmgr: Pass resources
  soc: ixp4xx: Remove unused functions
  soc: ixp4xx: Uninline several functions
  soc: ixp4xx: npe: Pass addresses as resources
  ARM: ixp4xx: Turn the QMGR into a platform device
  ARM: ixp4xx: Turn the NPE into a platform device
  ...
2019-05-16 08:31:32 -07:00
Linus Torvalds 132d68d37d USB/PHY patches for 5.2-rc1
Here is the big set of USB and PHY driver patches for 5.2-rc1
 
 There is the usual set of:
 	- USB gadget updates
 	- PHY driver updates and additions
 	- USB serial driver updates and fixes
 	- typec updates and new chips supported
 	- mtu3 driver updates
 	- xhci driver updates
 	- other tiny driver updates
 
 Nothing really interesting, just constant forward progress.
 
 All of these have been in linux-next for a while with no reported
 issues.  The usb-gadget and usb-serial trees were merged a bit "late",
 but both of them had been in linux-next before they got merged here last
 Friday.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNKuwg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymRUgCfa8Ri7KrCaBR5NHQcLhbdrX90ToQAmgNw7vpo
 fqt0XpNM0CSa9O/gOr79
 =8HFh
 -----END PGP SIGNATURE-----

Merge tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/PHY updates from Greg KH:
 "Here is the big set of USB and PHY driver patches for 5.2-rc1

  There is the usual set of:

   - USB gadget updates

   - PHY driver updates and additions

   - USB serial driver updates and fixes

   - typec updates and new chips supported

   - mtu3 driver updates

   - xhci driver updates

   - other tiny driver updates

  Nothing really interesting, just constant forward progress.

  All of these have been in linux-next for a while with no reported
  issues. The usb-gadget and usb-serial trees were merged a bit "late",
  but both of them had been in linux-next before they got merged here
  last Friday"

* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
  USB: serial: f81232: implement break control
  USB: serial: f81232: add high baud rate support
  USB: serial: f81232: clear overrun flag
  USB: serial: f81232: fix interrupt worker not stop
  usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
  usb: dwc3: Fix default lpm_nyet_threshold value
  usb: dwc3: debug: Print GET_STATUS(device) tracepoint
  usb: dwc3: Do core validation early on probe
  usb: dwc3: gadget: Set lpm_capable
  usb: gadget: atmel: tie wake lock to running clock
  usb: gadget: atmel: support USB suspend
  usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
  dwc2: gadget: Fix completed transfer size calculation in DDMA
  usb: dwc2: Set lpm mode parameters depend on HW configuration
  usb: dwc2: Fix channel disable flow
  usb: dwc2: Set actual frame number for completed ISOC transfer
  usb: gadget: do not use __constant_cpu_to_le16
  usb: dwc2: gadget: Increase descriptors count for ISOC's
  usb: introduce usb_ep_type_string() function
  usb: dwc3: move synchronize_irq() out of the spinlock protected block
  ...
2019-05-08 10:03:52 -07:00
Olof Johansson 56e49cd668 This update for DaVinci SoC support simplifies the VBUS enable
and overcurrent handling code in DA8XX OHCI driver by modeling
 vbus GPIO as a regulator. This unifies code for all users, device
 tree and non-device-tree.
 
 The OHCI driver patches have been acked by its maintainer.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJctKWDAAoJEGFBu2jqvgRN7rsP/iIM7h+mmny5r3pcEj/ALiLL
 iLo2FBgLokRYZnLSg+Ar7Rx3tNxWxwTB/N6yy1bS05Ozpbw0YD4sFoZ1h1CEa7eH
 Ez5WU2E+rcR4EtA06LDe/e0Dzhzjy9OAbV9cUsvUgWpjwlRPPKQ9Z5/yWUx4RRmc
 GsFNjYvUvxYTrydr11vnMdz/MKwXq/TRTRoGSRTgP5fUzlQSWW0sj/IEtP/54ANN
 iqH2RQlPRFzGhjpnpxym0yv1owIO81WzoxW0jat1JfnJE/KnfepSSyuBRXhW2s1d
 owWuh/0T8dSvkayGAQiPpZlfH8QjM84RJwLEDfNbnftvOx3whbP9SnwON3USmE/7
 qraIbbkEizF5tlMcd1gDHBdssuYEREm0Ea337L6pFIFv89Mos1C0BsReJCnqIwXs
 yREGYkaStNkb/QIa1VZv6EqhHlop6l03Gm7afXAt6Q887ER9GjurmcndPy58hfId
 B3F+ipzDxVMttdH5zZaL2PVcztNDRsHzRQEatd7jgn/hKHluLHsA/LHUEndXhjyZ
 uZkHomgEUwSNrrl4z3oPN536PaWHoKlJLkY33RZLeljDo9wC90pWY67DVGAHQywV
 c2Mkdqdo1WGWsNGFYncsW2M27h7y5g0N/T/DDlT3cm1J0qR2wRVH9UjnMRInPesO
 P9vjCf0LidxgJcIjLeTY
 =JFVt
 -----END PGP SIGNATURE-----

Merge tag 'davinci-for-v5.2/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/soc

This update for DaVinci SoC support simplifies the VBUS enable
and overcurrent handling code in DA8XX OHCI driver by modeling
vbus GPIO as a regulator. This unifies code for all users, device
tree and non-device-tree.

The OHCI driver patches have been acked by its maintainer.

* tag 'davinci-for-v5.2/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  usb: ohci-da8xx: drop the vbus GPIO
  ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx
  ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx
  usb: ohci-da8xx: disable the regulator if the overcurrent irq fired
  usb: ohci-da8xx: let the regulator framework keep track of use count
  ARM: davinci: add missing sentinels to GPIO lookup tables

Signed-off-by: Olof Johansson <olof@lixom.net>
2019-04-28 23:07:37 -07:00
Mathias Nyman 5afa0a5ed3 usb: xhci: add endpoint context tracing when an endpoint is added
The configure endpoint command configures all the endpoints that were
flagged to be added or dropped.

To know the content of each of the added endpoints we need to add tracing
to the .add_endpoint() callback, just after initializing all the context
values.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Mathias Nyman 90d6d5731d xhci: Add tracing for input control context
Add tracing for the add and drop bits in the input control context
used in Address device, configure endpoint, evaluate context commands.

The add and drop bits tell xHC which enpoints are added and dropped.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Mathias Nyman d70d5a8466 xhci: add port and bus number to port dynamic debugging
Improve port related dynamic debugging by printing out the bus number,
port number and port status register content each time there is a port
related debug messages.

Use the same port numbering method as usbcore to simplify debugging.
i.e. starting with port number 1.

Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Nicolas Saenz Julienne 33e39350eb usb: xhci: add Immediate Data Transfer support
Immediate data transfers (IDT) allow the HCD to copy small chunks of
data (up to 8bytes) directly into its output transfer TRBs. This avoids
the somewhat expensive DMA mappings that are performed by default on
most URBs submissions.

In the case an URB was suitable for IDT. The data is directly copied
into the "Data Buffer Pointer" region of the TRB and the IDT flag is
set. Instead of triggering memory accesses the HC will use the data
directly.

The implementation could cover all kind of output endpoints. Yet
Isochronous endpoints are bypassed as I was unable to find one that
matched IDT's constraints. As we try to bypass the default DMA mappings
on URB buffers we'd need to find a Isochronous device with an
urb->transfer_buffer_length <= 8 bytes.

The implementation takes into account that the 8 byte buffers provided
by the URB will never cross a 64KB boundary.

Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-27 14:53:58 +02:00
Chunfeng Yun 08048c04cc usb: host: xhci-plat: get optional clock by devm_clk_get_optional()
When the driver tries to get optional clock, it ignores all errors except
-EPROBE_DEFER, but if only ignores -ENOENT, it will cover some real errors,
such as -ENOMEM, so use devm_clk_get_optional() to get optional clock.

Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:24:25 +02:00
Chunfeng Yun 9d918dcea0 usb: xhci-mtk: get optional clock by devm_clk_get_optional()
Use devm_clk_get_optional() to get optional clock instead of
optional_clk_get() which uses devm_clk_get() to get clock and
checks for -EPROBE_DEFER but not -ENOENT as devm_clk_get_optional()
does, in fact, only ignoring -ENOENT will cover more errors, so the
replacement doesn't change original purpose.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
Yan Zhu 9bcb762ce0 usb: host: use usb_endpoint_maxp instead of usb_maxpacket
fhci_queue_urb() shouldn't use urb->pipe to compute the maxpacket
size anyway.It should use usb_endpoint_maxp(&urb->ep->desc).

Signed-off-by: Yan Zhu <zhuyan34@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-19 14:23:34 +02:00
JC Kuo 5f9be5f3f8 usb: host: xhci-tegra: Add Tegra186 XUSB support
This commit adds Tegra186 XUSB host mode controller support. This is
very similar to the existing support for Tegra124 and Tegra210, except
that the number of ports and PHYs differs and the IPFS wrapper being
gone.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 12:15:53 +02:00
JC Kuo 160fa3a1f5 usb: host: xhci-tegra: Selectively program IPFS
Starting with Tegra186, the XUSB controller no longer has the IPFS
wrapper. This commit adds a "has_ipfs" field to struct tegra_xusb_soc
that can be used to declare the existence of the IPFS wrapper.

For the existing chips (i.e. Tegra124 and Tegra210), the new field is
set to true. A future patch adding support for Tegra186 will set it to
false.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-16 12:15:53 +02:00
Bartosz Golaszewski 512de1ce7b usb: ohci-da8xx: drop the vbus GPIO
All users now setup a fixed regulator for the vbus supply. We can drop
the vbus GPIO code.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-04-12 19:46:48 +05:30
Bartosz Golaszewski d327330185 usb: ohci-da8xx: disable the regulator if the overcurrent irq fired
Historically the power supply management in this driver has been handled
in two separate places in parallel. Device-tree users simply defined an
appropriate regulator, while two boards with no DT support (da830-evm and
omapl138-hawk) passed functions defined in their respective board files
over platform data. These functions simply used legacy GPIO calls to
watch the oc GPIO for interrupts and disable the vbus GPIO when the irq
fires.

Commit d193abf1c9 ("usb: ohci-da8xx: add vbus and overcurrent gpios")
updated these GPIO calls to the modern API and moved them inside the
driver.

This however is not the optimal solution for the vbus GPIO which should
be modeled as a fixed regulator that can be controlled with a GPIO.

In order to keep the overcurrent protection available once we move the
board files to using fixed regulators we need to disable the enable_reg
regulator when the overcurrent indicator interrupt fires. Since we
cannot call regulator_disable() from interrupt context, we need to
switch to using a oneshot threaded interrupt.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-04-12 19:45:52 +05:30
Bartosz Golaszewski 8e2f5eae24 usb: ohci-da8xx: let the regulator framework keep track of use count
There's no reason to have a separate variable to keep track of the
regulator state. The regulator core already does that. Remove
reg_enabled from struct da8xx_ohci_hcd.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-04-12 19:43:54 +05:30
Will Deacon fb24ea52f7 drivers: Remove explicit invocations of mmiowb()
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:

	@mmiowb@
	@@
	- mmiowb();

and invoked as:

$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done

NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
2019-04-08 12:01:02 +01:00
Greg Kroah-Hartman 8cdfd068c1 Merge 5.1-rc3 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-01 07:42:04 +02:00
Mukesh Ojha f276e00279 usb: u132-hcd: fix resource leak
if platform_driver_register fails, cleanup the allocated resource
gracefully.

Signed-off-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-28 00:08:49 +09:00
Kangjie Lu 3de3dbe7c1 usb: u132-hcd: fix potential NULL pointer dereference
In case create_singlethread_workqueue fails, the fix notifies
callers the error to avoid potential NULL pointer dereferences.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-26 16:42:53 +09:00
Mathias Nyman d92f2c59cc xhci: Don't let USB3 ports stuck in polling state prevent suspend
Commit 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.

Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.

Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).

Original patch was sent to stable, this one should go there as well

Fixes: 2f31a67f01 ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-22 17:16:05 +01:00
Mathias Nyman 8867ea2621 usb: xhci: dbc: Don't free all memory with spinlock held
The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled

move the memory cleanup outside the spinlock

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-22 17:16:05 +01:00
Mathias Nyman 6cbcf59693 xhci: Fix port resume done detection for SS ports with LPM enabled
A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.

Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.

Add U1 and U2 to the possible link states when checking for finished
port resume.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-22 17:16:05 +01:00
Yasushi Asano 40fc165304 usb: host: xhci-rcar: Add XHCI_TRUST_TX_LENGTH quirk
When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.

[  101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?

Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.

Signed-off-by: Yasushi Asano <yasano@jp.adit-jv.com>
Signed-off-by: Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-03-19 14:57:31 +01:00
Linus Torvalds b7a7d1c1ec DMA mapping updates for 5.1
- add debugfs support for dumping dma-debug information (Corentin Labbe)
  - Kconfig cleanups (Andy Shevchenko and me)
  - debugfs cleanups (Greg Kroah-Hartman)
  - improve dma_map_resource and use it in the media code
  - arch_setup_dma_ops / arch_teardown_dma_ops cleanups
  - various small cleanups and improvements for the per-device coherent
    allocator
  - make the DMA mask an upper bound and don't fail "too large" dma mask
    in the remaning two architectures - this will allow big driver
    cleanups in the following merge windows
 -----BEGIN PGP SIGNATURE-----
 
 iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlyCKUgLHGhjaEBsc3Qu
 ZGUACgkQD55TZVIEUYP1vA//WNK5cxQVGZZsmsmkcNe3sCaJCZD4MpVpq/D+l87t
 3j1C1qmduOPyI1m061niYk7j4B4DeyeLs+XOeUsl5Yz+FqVvDICuNHXXJQSUr3Ao
 JbMfBis8Ne65Eyz0xxBltCWM7WiE6fdo7AGoR4Bzj3+f4xGOOazkRy4R6r67bU6x
 v3R5dTvfbSlvvKhn+j8ksAEYb+WPUmr6Z2dnlF0mShnOCpZVy0wd0M1gtEFKrVHx
 zKz9/va4/7yEcpdVqNtSDlHIsSZcFE3ZfTRWq6ZtBoRN+gNwrI0YylY7HtCfJWZG
 IxMiuQ+8SHGE8+NI2d56bs4MsHbqPBRSuadJNuZaTzdxs6FDTEnlCDeXwGF1cHf2
 qhVMfn17V4TZNT4NAd2wHa60cjTMoqraWeS06/b2tyXTF0uxyWj0BCjaHNJa+Ayc
 KCulq1n2LmTDiOGnZJT7Oui6PO5etOHAmvgMQumBNkzQJbPGvuiYGgsciYAMSmuy
 NccIrghQzR9BlG6U1srzTiGQJnpm38x1hWphtU6gQPwz5iKt3FBAfEWCic8U81QE
 JKSwoYv/5ChO+sy9880t/FLO8hn/7L55IOdZEfGkQ22gFzf3W5f9v2jFQc8XN2BO
 Fc6EjWERrmTzUi0f1Ooj3VPRtWuZq86KqlKByy6iZ5eXwxpGE1M0HZVoHYCW+aDd
 MYc=
 =nAMI
 -----END PGP SIGNATURE-----

Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping

Pull DMA mapping updates from Christoph Hellwig:

 - add debugfs support for dumping dma-debug information (Corentin
   Labbe)

 - Kconfig cleanups (Andy Shevchenko and me)

 - debugfs cleanups (Greg Kroah-Hartman)

 - improve dma_map_resource and use it in the media code

 - arch_setup_dma_ops / arch_teardown_dma_ops cleanups

 - various small cleanups and improvements for the per-device coherent
   allocator

 - make the DMA mask an upper bound and don't fail "too large" dma mask
   in the remaning two architectures - this will allow big driver
   cleanups in the following merge windows

* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
  Documentation/DMA-API-HOWTO: update dma_mask sections
  sparc64/pci_sun4v: allow large DMA masks
  sparc64/iommu: allow large DMA masks
  sparc64: refactor the ali DMA quirk
  ccio: allow large DMA masks
  dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
  dma-mapping: remove dma_mark_declared_memory_occupied
  dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
  dma-mapping: improve selection of dma_declare_coherent availability
  dma-mapping: remove an incorrect __iommem annotation
  of: select OF_RESERVED_MEM automatically
  device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
  mfd/sm501: depend on HAS_DMA
  dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
  dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
  dma-mapping: move debug configuration options to kernel/dma
  dma-debug: add dumping facility via debugfs
  dma: debug: no need to check return value of debugfs_create functions
  videobuf2: replace a layering violation with dma_map_resource
  dma-mapping: don't BUG when calling dma_map_resource on RAM
  ...
2019-03-10 11:54:48 -07:00
Linus Torvalds f90d64483e USB/PHY patches for 5.1-rc1
Here is the big USB/PHY driver pull request for 5.1-rc1.
 
 The usual set of gadget driver updates, phy driver updates (you will
 have a merge issue with Kconfig and Makefile), xhci updates, and typec
 additions.  Also included in here are a lot of small cleanups and fixes
 and driver updates where needed.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXH+hsw8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ynfNwCgqKKg+MxJ9pFjrwfWYOrbk+BBe2UAn2Elp4ia
 8FTdneQfN2J8Hhc6KGXE
 =Kx9I
 -----END PGP SIGNATURE-----

Merge tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/PHY updates from Greg KH:
 "Here is the big USB/PHY driver pull request for 5.1-rc1.

  The usual set of gadget driver updates, phy driver updates, xhci
  updates, and typec additions. Also included in here are a lot of small
  cleanups and fixes and driver updates where needed.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
  wusb: Remove unnecessary static function ckhdid_printf
  usb: core: make default autosuspend delay configurable
  usb: core: Fix typo in description of "authorized_default"
  usb: chipidea: Refactor USB PHY selection and keep a single PHY
  usb: chipidea: Grab the (legacy) USB PHY by phandle first
  usb: chipidea: imx: set power polarity
  dt-bindings: usb: ci-hdrc-usb2: add property power-active-high
  usb: chipidea: imx: remove unused header files
  usb: chipidea: tegra: Fix missed ci_hdrc_remove_device()
  usb: core: add option of only authorizing internal devices
  usb: typec: tps6598x: handle block writes separately with plain-I2C adapters
  usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
  usb: xhci: fix build warning - missing prototype
  usb: xhci: dbc: Fixing typo error.
  usb: xhci: remove unused member 'parent' in xhci_regset struct
  xhci: tegra: Prevent error pointer dereference
  USB: serial: option: add Telit ME910 ECM composition
  usb: core: Replace hardcoded check with inline function from usb.h
  usb: core: skip interfaces disabled in devicetree
  usb: typec: mux: remove redundant check on variable match
  ...
2019-03-06 16:48:27 -08:00
Balaji Manoharan 8fde481ef3 usb: xhci: Fix for Enabling USB ROLE SWITCH QUIRK on INTEL_SUNRISEPOINT_LP_XHCI
This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.

Signed-off-by: Balaji Manoharan <m.balaji@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-21 10:54:22 +01:00
Jean-Philippe Menil 4ee925dfe0 usb: xhci: fix build warning - missing prototype
Fix build warning when building drivers/usb/host/xhci-mem.o with W=1 due
to missing prototype for xhci_free_virt_devices_depth_first.

This function is only used in xhci-mem.c so just make it static.

Signed-off-by: Jean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-21 10:54:22 +01:00
Prabhat Chand Pandey ea5cc92517 usb: xhci: dbc: Fixing typo error.
Replaced "xhci_dbc_flush_reqests" with xhci_dbc_flush_requests".

Signed-off-by: Prabhat Chand Pandey <prabhat.chand.pandey@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20 20:18:23 +01:00
Chunfeng Yun 58f7691fd7 usb: xhci: remove unused member 'parent' in xhci_regset struct
The member @parent of xhci_regset struct is not used in fact,
so remove it

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20 20:18:23 +01:00
Thierry Reding 0326ccb5fe xhci: tegra: Prevent error pointer dereference
During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: 6494a9ad86 ("usb: xhci: tegra: Add genpd support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20 17:55:04 +01:00
Christoph Hellwig 82c5de0ab8 dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
All users of dma_declare_coherent want their allocations to be
exclusive, so default to exclusive allocations.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-20 07:27:00 -07:00
YueHaibing 8e9fd85c59 usb: host: oxu210hp-hcd: remove set but not used variables 'uframes, transfer_buffer_length'
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/usb/host/oxu210hp-hcd.c: In function 'scan_periodic':
drivers/usb/host/oxu210hp-hcd.c:2256:13: warning:
 variable 'uframes' set but not used [-Wunused-but-set-variable]

drivers/usb/host/oxu210hp-hcd.c: In function 'oxu_urb_enqueue':
drivers/usb/host/oxu210hp-hcd.c:2835:6: warning:
 variable 'transfer_buffer_length' set but not used [-Wunused-but-set-variable]

They are never used since introduction.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-19 14:41:38 +01:00
Arnd Bergmann b8961b1eb7 Merge tag 'davinci-for-v5.1/soc-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
DaVinci SoC updates for v5.1 (part 2)

This pull request contains changes needed to help get rid of
hard-coded GPIO base value passed from DaVinci platform data.

The OHCI related changes also help by moving over-current support
from board-files to OHCI driver making future DT-coversion easy.

The OHCI parts are acked by its maintainer.

* tag 'davinci-for-v5.1/soc-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  usb: ohci-da8xx: remove unused callbacks from platform data
  ARM: davinci: da830-evm: remove legacy usb helpers
  ARM: davinci: omapl138-hawk: remove legacy usb helpers
  usb: ohci-da8xx: add vbus and overcurrent gpios
  ARM: davinci: da830-evm: use gpio lookup entries for usb gpios
  ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios
  usb: ohci-da8xx: add a helper pointer to &pdev->dev
  usb: ohci-da8xx: add a new line after local variables
  ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API
  ARM: davinci: mityomapl138: use device properties for at24 eeprom
  ARM: davinci: mityomapl138: use nvmem notifiers
  ARM: davinci: remove dead code related to MAC address reading
  ARM: davinci: sffsdr: use device properties for at24 eeprom
  ARM: davinci: sffsdr: fix the at24 eeprom device name
  ARM: davinci: dm646x-evm: use device properties for at24 eeprom
  ARM: davinci: dm644x-evm: use device properties for at24 eeprom
  ARM: davinci: da830-evm: use device properties for at24 eeprom
  ARM: davinci: dm365-evm: use device properties for at24 eeprom
  ARM: davinci: mityomapl138: don't read the MAC address from machine code
  ARM: davinci: da850-evm: remove dead MTD code

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2019-02-15 20:38:14 +01:00
Colin Ian King a8ded8eb77 usb: host: oxu210hp-hcd: fix indentation issue
A statement is indented too deeply, fix this by removing a tab.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-02-12 10:30:48 +01:00
Bartosz Golaszewski d193abf1c9 usb: ohci-da8xx: add vbus and overcurrent gpios
There are two users upstream which register external callbacks for
switching the port power on/off and overcurrent protection. Both
users only use two GPIOs for that. Instead of having that functionality
in the board files, move the logic into the OHCI driver - including
the interrupt handler for overcurrent detection.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-02-12 13:48:51 +05:30
Bartosz Golaszewski 3d2ab9f35e usb: ohci-da8xx: add a helper pointer to &pdev->dev
Add a helper pointer to &pdev->dev. This improves readability by
removing all the &pdev->dev dereferencing.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-02-12 13:28:40 +05:30
Bartosz Golaszewski 08e46f18b7 usb: ohci-da8xx: add a new line after local variables
Add a new line after local variables. This improves the coding style.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2019-02-12 13:28:40 +05:30
Miquel Raynal f91649c525 usb: ehci-orion: add S2RAM support
Add suspend/resume callbacks to reset the host controller properly
during S2RAM operation.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:22:35 +01:00
Miquel Raynal e04585184d usb: ehci-orion: avoid double PHY initialization
No need to initialize the PHY from the driver's probe. It is done by
the core automatically and doing it twice would increment the
phy->powercount counter to 2 instead of 1. During later suspend
operation, the counter will be decremented to one, no phy->power_off()
will occur and worse than that, the following phy->power_on() at
resume time will also be skipped, failing the whole S2RAM operation.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:22:35 +01:00
Ofer Heifetz 12453a897e usb: host: xhci: mvebu: add reset on resume quirk
The mvebu xHCI host driver does not have suspend/resume support. Use of
the XHCI_RESET_ON_RESUME quirk is mandatory in order to avoid failures
after resume. This will work only if no USB device is plugged-in.

While at it, mention in the Kconfig file that this IP is also present
on the A3700 SoC.

Signed-off-by: Ofer Heifetz <oferh@marvell.com>
[miquel.raynal@bootlin.com: Reword the commit message]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-30 09:22:35 +01:00
Greg Kroah-Hartman c9381e185f Merge 5.0-rc4 into usb-next
We need the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-28 08:44:58 +01:00
Greg Kroah-Hartman e36f8b7b7d USB: host: whci: rename Kbuild file
We have been using Makefile for well over a decade now, use that name
instead of Kbuild.

Also, while moving the file, add the proper SPDX identifier at the top
of it.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22 09:08:17 +01:00
Greg Kroah-Hartman cae8dc3b68 USB: add missing SPDX lines to Kconfig and Makefiles
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles.  Add
the correct GPL-2.0 identifier to them to make scanning tools happy.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-22 09:08:17 +01:00
Lubomir Rintel 70d0ba4cf7 USB: EHCI: ehci-mv: add MODULE_DEVICE_TABLE
This fixes autoloading the module by the OF compatible string.

Fixes: 813e18b18a ("USB: EHCI: ehci-mv: add DT support")
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 10:07:05 +01:00
Ran Wang 5f620bb643 drivers: usb :fsl: Remove USB Errata checking code
Remove USB errata checking code from driver. Applicability of erratum
is retrieved by reading corresponding property in device tree.
This property is written during device tree fixup.

Besides, replace spaces with tabs to make code aligned.

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 10:02:09 +01:00
Ran Wang 73855109a9 usb: kconfig: remove dependency FSL_SOC for ehci fsl driver
CONFIG_USB_EHCI_FSL is not dependent on FSL_SOC, it can be built on
non-PPC platforms.

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 10:02:09 +01:00
Ran Wang 972a34e1c7 usb: ehci: fsl: Update register accessing for arm/arm64 platforms
arm/arm64's io.h doesn't define clrbits32() and clrsetbits_be32(), which
causing compile failure on some Layerscape Platforms (such as LS1021A and
LS2012A which also integrates FSL EHCI controller). So use
ioread32be()/iowrite32be() instead to make it workable on both
powerpc and arm.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-01-18 10:02:09 +01:00