This adds support for the AU Optronics G185HAN01 18.5" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the AU Optronics G133HAN01 13.3" LVDS FullHD TFT
LCD panel, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Convert from a single mode to display timings, which allow to describe
the minimum/maximium blanking and clock rates, add enable/disable delays
and provide the bus format.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LQ123P1JX31 panel support 8 bits per component.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In the loop on .timings, we should check .num_timings to see if it's the
only mode specified, not .num_modes, which should be used with .modes.
Fixes: cda553725c ("drm/panel: simple: Set appropriate mode type")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Chunghwa CLAA070WP03XG is a 7" 1280x800 panel, which can be
supported by the simple panel driver.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO T215HVN01 is a 21.5" FHD (1920x1080) color TFT LCD panel.
This panel is used on the Acer Chromebase 21.5-inch All-in-One (DC221HQ).
Link to spec: http://www.udmgroup.com/ftp/T215HVN01.0.pdf
v2: fix alphabetical order
v3: remove minor revision suffix ".0" and add link to spec
v4: add dt-binding documentation
Signed-off-by: Haixia Shi <hshi@chromium.org>
Tested-by: Haixia Shi <hshi@chromium.org>
Reviewed-by: Stéphane Marchesin <marcheu@chromium.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp 15" LQ150X1LG11 panel is an XGA TFT LCD panel.
The simple-panel driver is used to get support for essential
functionality of the panel.
Signed-off-by: Gustaf Lindström <gl@axentia.se>
Signed-off-by: Peter Rosin <peda@axentia.se>
[treding@nvidia.com: change .bpc from 8 to 6]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the JDI LT070ME05000 WUXGA DSI panel used in
Nexus 7 2013 devices.
Programming sequence for the panel is was originally found in the
android-msm-flo-3.4-lollipop-release branch from:
https://android.googlesource.com/kernel/msm.git
And video mode setting is from dsi-panel-jdi-dualmipi1-video.dtsi
file in:
git://codeaurora.org/kernel/msm-3.10.git LNX.LA.3.6_rb1.27
Cc: Archit Taneja <archit.taneja@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The format is RGB888 not RGB666.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Taking our cue from commit a42f6e3f8f ("drm/panel: simple: Add delay
timing for Sharp LQ123P1JX31"), let's add timings:
.prepare = t1 + t3
.enable = t7
.unprepare = t11 + 12
Without this, the panel may not be given enough time to come up.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This display expects DE pin and data lines to be active high, add the
necessary flags.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for Innolux Corporation 10.1" G101ICE-L01 WXGA
(1280x800) LVDS panel to the simple-panel driver.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to page 16 of the Sharp LQ123P1JX31 datasheet, we need to add
the missing delay timing. Panel prepare time should be t1 (0.5 to 10 ms)
plus t3 (0 to 100 ms), panel enable time should equal to t7 (0 to 50 ms)
and panel unprepare time should be t11 (1 to 50 ms) plus t12 (500 ms).
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add simple-panel support for the Sharp LQ101K1LY04, which is a 10"
WXGA (1280x800) LVDS panel.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG LP079QX1-SP0V is an 7.9" QXGA TFT with LED Backlight unit and
32 pins eDP interface. This module supports 1536x2048 mode.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LQ123P1JX31 is an 12.3", 2400x1600 TFT-LCD panel connected
using eDP interfaces.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Samsung LSN122DL01-C01 is an 12.2" 2560x1600 (WQXGA) TFT-LCD panel
connected using eDP interfaces.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG LP097QX1-SPA1 is an 9.7", 2048x1536 (QXGA) TFT-LCD panel
connected using eDP interfaces.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some backlight drivers ignore the power property and instead only use
the state property. Fixup the panel driver to set the state property in
addition to the power property.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This blank line was introduced in commit c8521969de ("drm/panel:
simple: Add support for BOE TV080WUM-NL0"), likely by mistake.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both the Innolux ZJ070NA-01P and Samsung LTN101NT05 were listing the
horizontal and vertical resolutions in the size.width and size.height
fields, whereas they should contain the physical dimensions of the
panel.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for TPK U.S.A. LLC Fusion 7", 10.1" panels to the DRM simple
panel driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Innolux AT070TN92 panel.
Signed-off-by: Riccardo Bortolato <bortolato@navaltechitalia.it>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All modes exposed by simple panels should be tagged as driver defined
modes. Moreover, if a panel supports only one mode, this mode is
obviously the preferred one.
Doing this also fix a problem occurring when a 'video=' parameter is
passed on the kernel command line. In some cases the user provided mode
will be preferred over the simple panel ones, which might result in
unpredictable behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[treding@nvidia.com: reshuffle some code for consistency]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Olimex LCD-OLinuXino-4.3TS panel to the DRM simple
panel driver.
It is a 480x272 panel connected through a 24-bits RGB interface.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a basic TFT panel with a 40-pin FPC connector on it. The
specification doesn't define timings, but the Adafruit instructions
were setting up 800x480 CVT.
v2: Add .bus_format and vsync/hsync flags.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
[treding@nvidia.com: keep entries properly sorted]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The drivers current default configuration drives the pixel data
on rising edge of the pixel clock. However, most display sample
data on rising edge... This leads to color shift artefacts visible
especially at edges.
This patch changes the relevant defines to be useful and actually
set the bits, and changes pixel clock polarity to drive the pixel
data on falling edge by default. The patch also adds an explicit
pixel clock polarity flag to the display introduced with the driver
(NEC WQVGA "nec,nl4827hc19-05b") using the new bus_flags field to
retain the initial behavior.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Introduce bus_flags to specify display bus properties like signal
polarities. This is useful for parallel display buses, e.g. to
specify the pixel clock or data enable polarity.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
This contains a refactoring of parts of the DSI core to allow creating
DSI devices from non-DSI control busses (i.e. I2C, SPI, ...).
Other than that there's support for a couple of new panels as well as
a few cleanup patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zrRb
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux into drm-next
drm/panel: Changes for v4.6-rc1
This contains a refactoring of parts of the DSI core to allow creating
DSI devices from non-DSI control busses (i.e. I2C, SPI, ...).
Other than that there's support for a couple of new panels as well as
a few cleanup patches.
* tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux:
drm/bridge: Make (pre/post) enable/disable callbacks optional
drm/panel: simple: Add URT UMSH-8596MD-xT panels support
dt-bindings: Add URT UMSH-8596MD-xT panel bindings
of: Add United Radiant Technology Corporation vendor prefix
drm/panel: simple: Support for LG lp120up1 panel
dt-bindings: Add LG lp120up1 panel bindings
drm/panel: simple: Fix g121x1_l03 hsync/vsync polarity
drm/dsi: Get DSI host by DT device node
drm/dsi: Add routine to unregister a DSI device
drm/dsi: Try to match non-DT DSI devices
drm/dsi: Use mipi_dsi_device_register_full() for DSI device creation
drm/dsi: Check for CONFIG_OF when defining of_mipi_dsi_device_add()
Add support for United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT
LCD panels in the simple-panel driver.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG lp120up1 TFT LCD panel with eDP interface is a 12.0" 1920x1280
panel, which can be supported by the simple panel driver.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set hsync/vsync to active low for g121x1_l03 panel to match the
recommended setting in the datasheet.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current default configuration is as follows:
- Invert VSYNC signal (active LOW)
- Invert HSYNC signal (active LOW)
The mode flags allow to specify the required polarity per
mode. Furthermore, none of the current driver settings is
actually a standard polarity.
This patch applies the current driver default polarities as
explicit flags to the display which has been introduced with
the driver (NEC WQVGA "nec,nl4827hc19-05b"). The driver now
also parses the flags field and applies the configuration
accordingly, by using the following values as standard
polarities: (e.g. when no flags are specified):
- VSYNC signal not inverted (active HIGH)
- HSYNC signal not inverted (active HIGH)
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Document that 'width' and 'height' are measured in millimeters.
Signed-off-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Kyocera TCG121XGLP panel is an XGA LCD TFT panel connected through
LVDS, which can be supported by the simple panel driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Sharp LS043T1LE01 is a 4.3", 540x960 TFT-LCD panel connected using
two DSI lanes. It is for example found on the Qualcomm Snapdragon 800
Dragonboard (APQ8074).
Signed-off-by: Werner Johansson <werner.johansson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the Panasonic panel found in some Xperia Z2
tablets.
Signed-off-by: Werner Johansson <werner.johansson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The BOE TV080WUM-NL0 is an 8.0", 1200x1920 (WUXGA) TFT-LCD panel
connected using four DSI lanes. It can be supported by the simple-panel
driver.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The LG4573 is used on the LG LCD LB043WV2-SD01, an industrial 4.3" TFT
panel with SPI control interface.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Okaya RS800480T-7X0GP to the DRM simple panel
driver.
The RS800480T-7X0GP is a WVGA (800x480) panel with an 18-bit parallel
LCD interface. It supports pixel clocks in the range of 30-40 MHz.
This panel details can be found at:
http://boundarydevices.com/product/7-800x480-display/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for the NEC NL4827HC19-05B 480x272 panel to the DRM
simple panel driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[treding@nvidia.com: add .bpc field for panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B080UAN01 is an 8.0" WUXGA TFT LCD panel connected using four
DSI lanes. It can be supported by the simple-panel driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
According to the data sheet, the minimum horizontal blanking interval
is 54 clocks (1 + 52 + 1), but tests with a Nitrogen6X have shown the
minimum working horizontal blanking interval to be 60 clocks.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lucas Stach