iwl_power_update_mode expects to be called with mutex held, for example to
protect priv->vif. Only one caller currently does not do this, fix this.
Also, add a comment to iwl_power_update_mode to indicate this requirement.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
mac80211 will only enable powersaving for station mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Because DTIM information is required for powersave
but is only conveyed in beacons, wait for a beacon
before enabling powersave, and change the way the
information is conveyed to the driver accordingly.
mwl8k doesn't currently seem to implement PS but
requires the DTIM period in a different way; after
talking to Lennert we agreed to just have mwl8k do
the parsing itself in the finalize_join work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags
bit 0: Clear statistics
0: Do not clear Statistics counters
1: Clear to zero Statistics counters
Allow "clear" parameter to be set from the caller.
Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Duplicated define for listen interval (IWL_CONN_MAX_LISTEN_INTERVAL and
IWL_CONN_LISTEN_INTERVAL), remove IWL_CONN_LISTEN_INTERVAL
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Reported-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using device configuration structure to decide the type of thermal
throttle method for the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For static power save, the actual intervals are calculated by driver based on
the default table and DTIM flag, then sent to uCode when the scheme
is changed.
Three tables are defined based on DTIM period.
1. DTIM 0 - 2
2. DTIM 3 - 10
3. DTIM > 11
The actual number of DTIM a station may miss may not exceed the
following:
. Only 1 DTIM may be skipped at PI=4 when allowed
. Only 2 DTIMs may be skipped at PI=5 when allowed
. DTIM may be skipped only 5 sec after last activity
. DTIM may be skipped only 30 sec after connection establishment
Only allow user to override the power_level when rf is ready to make sure
power level gets changed upon request.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode detects critical temperature it should send "card state
notification" interrupt to driver and then shut itself down to prevent
overheating. There is a race condition where uCode shuts down before it
can deliver the interrupt to driver.
Additional method provided here for driver to enter CT_KILL state based
on temperature reading.
How it works:
Method 1:
If driver receive "card state notification" interrupt from uCode; it
enters "CT_KILL" state immediately
Method 2:
If the last temperature report by Card reach Critical temperature,
driver will send "statistic notification" request to uCode to verify the
temperature reading, if driver can not get reply from uCode within
300ms, driver will enter CT_KILL state automatically.
Method 3:
If the last temperature report by Card did not reach Critical
temperature, but uCode already shut down due to critical temperature.
All the host commands send to uCode will not get process by uCode;
when command queue reach the limit, driver will check the last reported
temperature reading, if it is within pre-defined margin, enter "CT_KILL"
state immediately. In this case, when uCode ready to exit from "CT_KILL" state,
driver need to restart the adapter in order to reset all the queues and
resume normal operation.
One additional issue being address here, when system is in CT_KILL
state, both tx and rx already stopped, but driver still can send host
command to uCode, it will flood the command queue since card was not
responding; adding STATUS_CT_KILL flag to reject enqueue host commands
to uCode if it is in CT_KILL state, when uCode is ready to come out of
CT_KILL, driver will clear the STATUS_CT_KILL bit and allow enqueue the host
commands to uCode to recover from CT_KILL state.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using powersave while idle saves a lot of power, but
we've had problems with this on some cards (5150 has
been reported to be problematic). However, on the new
6000 series we're seeing no problems, so for now let
that hardware benefit from idle mode, we can look at
the problems with other hardware one by one and then
enable those once we figure out the problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a bug in 4965 powersave that appears to
be related to the way it keeps track of its data
during sleep, but we haven't found it yet. Due to
that, using powersave may spontaneously cause the
device to SYSASSERT when transitioning from sleep
to wake. Therefore, disable powersave for 4965,
until (if ever, unfortunately) we can identify
and fix the problem.
Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982
which was closed, but now has re-appeared with
IDLE mode, which probably means we never really
fixed it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 does not have update_chain_flags defined and because if this we always
see the debug message that does not apply to it. Add a check to be specific
about what is actually happening.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some concerns were raised about the automatic adjustment
of sleep intervals to all the same, potentially high,
value, and I can imagine the hardware behaving better
when we don't ask too much of it.
So let's convert to use a succession of sleep levels
when requesting to go to deeper sleeps (which can only
happen with large DTIM intervals), using the succession
values from power level three, which have the benefit of
also having been tested extensively already.
As a result, the automatic sleep level adjustment will
now be mostly equivalent to power level three, except
for the RX/TX timeouts and possibly using smaller sleep
vectors to account for networking latency.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on required latency requested by pm_qos (via mac80211)
we can automatically adjust the sleep state. Also, mac80211 has
a user-visible dynamic sleep feature where we are supposed to
stay awake after sending/receiving frames to better receive
response frames to our packets, this can be integrated into the
sleep command.
Currently, and this patch doesn't change that yet, we default
to using sleep level 1 if PS is enabled. With a module parameter
to iwlcore, automatic adjustment to changing network latency
requirements can be enabled -- this isn't yet the default due
to requiring more testing.
The goal is to enable automatic adjustment and then go into the
deepest possible sleep state possible depending on the networking
latency requirements.
This patch does, however, enable IEEE80211_HW_SUPPORTS_DYNAMIC_PS
to avoid the double-timer (one in software and one in the device)
when transmitting -- the exact timeout may be ignored but that is
not of big concern.
Note also that we keep the hard-coded power indices around for
thermal throttling -- the specification of that calls for using
the specified power levels. Those can also be selected in debugfs
to allow easier testing of such parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the thermal throttle data structures and code
are really very intermingled with the sleep (power)
control code. They really do belong together in a way
since the thermal throttle code uses powersaving to
achieve its goal, but it's making it hard to work on
the powersave code. Split this up to make that easier.
I've also changed the antenna defines to an enum and
used the same enum for RX and TX.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the power update function, when driver fail to set the power, it
should not continue move forward and try to change the rx chain
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For legacy thermal throttling, set the new Thermal Throttling
state and change power index when thermal throttling manager detects
temperature changed. The current implementation sets the state to the
previous Thermal Throttling state, which causes system to enter wrong
power index. The worse case, it will trying to set the
lower power index when device reach critical temperature, it will cuase
issue for both system and the device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all the thermal throttling functions to background task to make
sure do not change power and rx chain in interrupt handler.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename "fat" to "ht40"
The term "fat channel" is deprecated in favor of "HT40"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part 2 of Thermal Throttling Management -
Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold
Two Thermal Throttling Management Methods; this patch introduce the
Advance Thermal Throttling:
TI-0: system power index, no tx/rx restriction, HT enabled
TI-1: power index 5, 1 spatial stream Tx, multiple spatial stream Rx, HT
enabled
TI-2: power index 5: 1 spatial stream Tx, 1 spatial stream Rx, HT
disabled
TI-CT-KILL: power index 5, no Tx, no Rx, HT disabled
For advance Thermal Throttling, CT_KILL_ENTER threshold and CT_KILL_EXIT
threshold are different; uCode will not stay awake until reach
CT_KILL_EXIT threshold.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Part 1 of Thermal Throttling Management -
Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold
Two Thermal Throttling Management Methods; this patch introduce the
Legacy Thermal Management:
IWL_TI_0: normal temperature, system power state
IWL_TI_1: high temperature detect, low power state
IWL_TI_2: higher temperature detected, lower power state
IWL_TI_CT_KILL: critical temperature detected, lowest power state
Once get into CT_KILL state, uCode go into sleep, driver will stop all
the active queues, then move to IWL_TI_CT_KILL state; also set up 5
seconds timer to toggle CSR flag, uCode wake up upon CSR flag change,
then measure the temperature.
If temperature is above CT_KILL exit threshold, uCode go backto sleep;
if temperature is below CT_KILL exit threshold, uCode send Card State
Notification response with appropriate CT_KILL status flag, and uCode
remain awake, Driver receive Card State Notification Response and update
the card temperature to the CT_KILL exit threshold.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes all the dead code that tries to adjust the power
saving level based on the system AC state (inacceptable policy
in the kernel) or based on overtemp conditions (unused).
Also, pass _all_ policy wrt. enabling PS to mac80211, since
we do not use the power_disabled internally I now use that to
mirror the mac80211 CONF_PS setting. When mac80211 turns off
CONF_PS we follow suit. This means that the user power level
(which can currently only be set from sysfs) is not touched
for mac80211 powersave changes.
This means no "association status" checks are necessary since
mac80211 will not allow power save to be enabled when not
associated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi internally needs to keep track of whether PS
is enabled in the firmware or not. To do this, it keeps
a bit in the status flags, called STATUS_POWER_PMI.
The code to set this bit looks as follows:
static int iwl_set_power(struct iwl_priv *priv, void *cmd)
{
return iwl_send_cmd_pdu_async(priv, POWER_TABLE_CMD,
sizeof(struct iwl_powertable_cmd),
cmd, NULL);
}
int iwl_power_update_mode(...)
{
[...]
if (final_mode != IWL_POWER_MODE_CAM)
set_bit(STATUS_POWER_PMI, &priv->status);
iwl_update_power_cmd(priv, &cmd, final_mode);
cmd.keep_alive_beacons = 0;
if (final_mode == IWL_POWER_INDEX_5)
cmd.flags |= IWL_POWER_FAST_PD;
ret = iwl_set_power(priv, &cmd);
if (final_mode == IWL_POWER_MODE_CAM)
clear_bit(STATUS_POWER_PMI, &priv->status);
else
set_bit(STATUS_POWER_PMI, &priv->status);
if (priv->cfg->ops->lib->update_chain_flags && update_chains)
priv->cfg->ops->lib->update_chain_flags(priv);
[...]
}
Now, this bit really needs to track what the _firmware_
thinks, not what the driver thinks. Therefore, there is
a race condition here -- the driver sets the bit before
it knows that the async command sent to the card in the
iwl_set_power function has been processed. As a result,
the call to update_chain_flags() may think that the card
has been woken up (PMI bit cleared) while in reality it
hasn't processed the async POWER_TABLE_CMD yet.
This leads to bugs -- any commands the update_chain_flags
function sends can get stuck and subsequent commands also
fail.
The fix is almost trivial: since there's no reason to send
an async command here (in fact, there almost never should
be since many mac80211 callbacks can sleep) just make the
function wait for the card to process the command and then
return and clear the PMI bit.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If user set new power level, accept the new power level and only
send command to host if the interface is up and radio on.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces where possible usage of pci register
defined in the driver by ones defined in pci_regs.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies 3945 and iwlagn power save management
This patch also better separates system state from user setting.
System state shall be removed later as this shall be shifted to user space
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call IWL_DEBUG macro with explicit priv argument.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch eliminates 3945 power_data structure and make use of
of iwl_power_data.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch rearrange code in iwl-power.c function to make it a little more
readable. No functional changes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes includes of iwl-helpers.h where not needed
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces personal emails with hopefully
always valid Intel Linux Wireless, which will be routed
to a current maintainer
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch doesn't fail power save setting when calibration is
not done yet. The new power index is registered and will
be evaluated again anyway upon calibration completion.
This patch also eliminates WARN_ON in mac80211 hw_config during
initialization
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwlwifi by removing uneeded declarations and removing
uneeded symbol export reducing the namespace pollution. It also fixes some
typos in comments.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes usage of the results from disconnected antenna alg to
know how many antennas are connected.
It also synchronizes between the chain noise alg and the W/A that
disables power management during association. All the antennas must be
enables during the chain noise algorithm. Hence, power management is
restored only after the completion of the algorithm.
In the future, we will need to update the AP that we don't support MIMO
if there is only one antenna connected. We also need to update the rate
scaling algorithm.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch disables power save upon association and enables it back
after association. This allows to associate to AP on a radar channel
if power save is enabled.
Radar and passive channels are not allowed for TX (required for association)
unless RX is received but PS may close the radio and no RX will be received
effectively failing association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up pci registers handling.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/ath5k/base.c
drivers/net/wireless/b43/main.c
drivers/net/wireless/ipw2100.c
drivers/net/wireless/ipw2200.c
drivers/net/wireless/iwlwifi/iwl-3945.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-5000.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-eeprom.c
drivers/net/wireless/iwlwifi/iwl-hcmd.c
drivers/net/wireless/iwlwifi/iwl-power.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects power_level in sysfs.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for power save for 5000 HW.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965.h to iwl-dev.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-commands to iwl-commands.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add power level support
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre