Just like the previous fix for LogitechHD Webcam c270 in commit
11e7064f35, c310 model also requires the
same workaround for avoiding the kernel warning.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59741
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the Android firmware enables the audio interfaces in accessory
mode, it always declares in the control interface's baInterfaceNr array
that interfaces 0 and 1 belong to the audio function. However, the
accessory interface itself, if also enabled, already is at index 0 and
shifts the actual audio interface numbers to 1 and 2, which prevents the
PCM streaming interface from being seen by the host driver.
To get the PCM interface interface to work, detect when the descriptors
point to the (for this driver useless) accessory interface, and redirect
to the correct one.
Reported-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Tested-by: Jeremy Rosen <jeremy.rosen@openwide.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 927c9423dd (ALSA: usb-audio: add
Edirol UM-3G support) used a wrong quirk type, which would make the
driver refuse to attach with the error message "MIDIStreaming interface
descriptor not found".
Cc: <stable@vger.kernel.org> # 3.3 and later
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check only the uppermost 16 bits instead of the whole 32 bits of
the version information. Do this because all firmware version tested
with this version information worked correctly and the strict check
causes problems for several users.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
freqshift is only set for the data endpoint and syncmaxsize is only set
for the sync endpoint. This results in a syncmaxsize of zero used in the
proc output feedback format calculation, which gives a feedback format
incorrectly shown as 8.16 for UAC2 devices.
As neither the data nor the sync endpoint gives all the relevant
content, output the two combined.
Also remove the sync_endpoint "packet size" which is always zero
and the sync_endpoint "momentary freq" which is constant.
Tested with UAC2 async and UAC1 adaptive, not tested with UAC1 async.
Reported-by: B. Zhang <bb.zhang@free.fr>
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code does this:
be16_to_cpu(buf[i * 2] << 8 | buf[(i * 2) + 1])
Which is effectively (neglecting the index):
be16_to_cpu(be16_to_cpu(*((u16 *) buf)))
This means the int16 in the buffer is not converted at all.
Daniel Mack confirmed that the driver works on little endian
CPUs, leading to the conclusion that the device-side structure
is actually little endian.
This changes the code to use le16_to_cpu().
Caught by sparse.
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a function to handle conversion from snd_pcm_format_t
to bitwise with proper typing.
Change such conversions to use this function and silence sparse
warnings.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent changes in the USB API ("implement new semantics for
URB_ISO_ASAP") made the former meaning of the URB_ISO_ASAP flag the
default, and changed this flag to mean that URBs can be delayed.
This is not the behaviour wanted by any of the audio drivers because
it leads to discontinuous playback with very small period sizes.
Therefore, our URBs need to be submitted without this flag.
Reported-by: Joe Rayhawk <jrayhawk@fairlystable.org>
Cc: <stable@vger.kernel.org> # 3.8 only
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Scarlett 2i2 seems to take almost 500 ms to set the sample rate,
even if the clock is currently set to that value. This patch speeds
up prepare of the device, by avoiding setting the clock to something
it already is.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got strange errors in get_ctl_value() in mixer.c during
probing, e.g. on Hercules RMX2 DJ Controller:
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x201, wIndex = 0xa00, type = 4
ALSA mixer.c:352 cannot get ctl value: req = 0x83, wValue = 0x200, wIndex = 0xa00, type = 4
....
It turned out that the culprit is autopm: snd_usb_autoresume() returns
-ENODEV when called during card->probing = 1.
Since the call itself during card->probing = 1 is valid, let's fix the
return value of snd_usb_autoresume() as success.
Reported-and-tested-by: Daniel Schürmann <daschuer@mixxx.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The USB_DT_CS_ENDPOINT class-specific endpoint descriptor is usually
stuffed directly after the standard USB endpoint descriptor, and this is
where the driver currently expects it to be.
There are, however, devices in the wild that have it the other way
around in their descriptor sets, so the USB_DT_CS_ENDPOINT comes
*before* the standard enpoint. Devices known to implement it that way
are "Sennheiser BTD-500" and Plantronics USB headsets.
When the driver can't find the USB_DT_CS_ENDPOINT, it won't be able to
change sample rates, as the bitmask for the validity of this command is
storen in bmAttributes of that descriptor.
Fix this by searching the entire interface instead of just the extra
bytes of the first endpoint, in case the latter fails.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Torstein Hegge <hegge@resisty.net>
Reported-and-tested-by: Yves G <alsa-user@vivigatt.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the timeout for USB control set messages according to the USB 2
spec, using the macros from include/linux/usb.h.
The get timout becomes 5000 ms even though it is 500 ms in the
spec. This patch is required to run the Hercules RMX2 which needs a
timeout of 1240 ms.
More notes from author:
I still distinguish between set and get but as long both are 5000 ms
GCC will remove it anyway. IMHO this is more easy read and there is no
need to explain why we use a get timeout for set messages.
Signed-off-by: Daniel Schürmann <daschuer@mixxx.org>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=MXrq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.10
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
Unfortunately, none of the UAC standards provides a way to identify DSD
(Direct Stream Digital) formats. Hence, this patch adds a quirks
handler to identify USB interfaces that are capable of handling DSD.
That quirks handler can augment the already parsed formats bit-field,
by any of the new SNDRV_PCM_FMTBIT_DSD_{U8_U16} and setting the dsd_dop
flag in the audio format, if the driver should take care for the DOP
byte stuffing.
The only devices that are known to work with this are the ones with
a 'Playback Designs' vendor id.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is quite some confusion around the bit-ordering in DSD samples,
and no general agreement that defines whether hardware is supposed to
expect the oldest sample in the MSB or the LSB of a byte.
ALSA will hence set the rule that on the software API layer, bytes
always carry the oldest bit in the most significant bit of a byte, and
the driver has to translate that at runtime in order to match the
hardware layout.
This patch adds support for this by adding a boolean flag to the
audio format struct.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to provide a compatibility way for pushing DSD
samples through ordinary PCM channels, the "DoP open Standard" was
invented. See http://www.dsd-guide.com for the official document.
The host is required to stuff DSD marker bytes (0x05, 0xfa,
alternating) in the MSB of 24 bit wide samples on the bus, in addition
to the 16 bits of actual DSD sample payload.
To support this, the hardware and software stride logic in the driver
has to be tweaked a bit, as we make the userspace believe we're
operating on 16 bit samples, while we in fact push one more byte per
channel down to the hardware.
The DOP runtime information is stored in struct snd_usb_substream, so
we can keep track of our state across multiple calls to
prepare_playback_urb_dsd_dop().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For normal PCM transfer, this change has no effect, as the endpoint's
stride is always frame_bits/8. For DSD DOP streams, however, which is
added later, the hardware stride differs from the software stride, and
the endpoint has the correct information in these cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 88a8516a21 (ALSA: usbaudio: implement USB autosuspend)
introduced autopm for all USB audio/MIDI devices. However, many MIDI
devices, such as synthesizers, do not merely transmit MIDI messages but
use their MIDI inputs to control other functions. With autopm, these
devices would get powered down as soon as the last MIDI port device is
closed on the host.
Even some plain MIDI interfaces could get broken: they automatically
send Active Sensing messages while powered up, but as soon as these
messages cease, the receiving device would interpret this as an
accidental disconnection.
Commit f5f165418c (ALSA: usb-audio: Fix missing autopm for MIDI input)
introduced another regression: some devices (e.g. the Roland GAIA SH-01)
are self-powered but do a reset whenever the USB interface's power state
changes.
To work around all this, just disable autopm for all USB MIDI devices.
Reported-by: Laurens Holst
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When recording at 176.2KHz or 192Khz, the device adds a 32-bit length
header to the capture packets, which obviously needs to be ignored for
recording to work properly.
Userspace expected: L0 L1 L2 R0 R1 R2
...but actually got: R2 L0 L1 L2 R0 R1
Also, the last byte of the length header being interpreted as L0 of
the first sample caused spikes every 0.5ms, resulting in a loud 16KHz
tone (about the highest 'B' on a piano) being present throughout
captures.
Tested at all sample rates on an E-Mu 0404USB, and tested for
regressions on a generic USB headset.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turns out the devices from Playback Design need the delay quirk
after usb_set_interface from clocks.c as well. Make it a proper
quirks function and factor out the code to quirks.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usb_control_msg() function expects __u16 types and performs
the endianness conversions by itself.
However, in three places, a conversion is performed before it is
handed over to usb_control_msg(), which leads to a double conversion
(= no conversion):
* snd_usb_nativeinstruments_boot_quirk()
* snd_nativeinstruments_control_get()
* snd_nativeinstruments_control_put()
Caught by sparse:
sound/usb/mixer_quirks.c:512:38: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:512:38: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:512:38: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:35: warning: incorrect type in argument 5 (different base types)
sound/usb/mixer_quirks.c:543:35: expected unsigned short [unsigned] [usertype] value
sound/usb/mixer_quirks.c:543:35: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:56: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:543:56: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:543:56: got restricted __le16 [usertype] <noident>
sound/usb/quirks.c:502:35: warning: incorrect type in argument 5 (different base types)
sound/usb/quirks.c:502:35: expected unsigned short [unsigned] [usertype] value
sound/usb/quirks.c:502:35: got restricted __le16 [usertype] <noident>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some clocks might be read-only, e.g., external clocks (see also
UAC2 4.7.2.1).
In this case, setting the sample frequency will always fail
(even if the rate is equal to the current clock rate),
therefore do not write, but read the value and compare to the
requested rate.
If the clock is read only, avoid reading it twice.
If it doesn't match, return -ENXIO since the clock is invalid for
this configuration.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show the error code returned from the USB subsystem in
the debug messages.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a module param to disable auto clock selection.
This is provided for users that expect the audio stream to
fail when the clock source is invalid (e.g., the word clock
was unintentionally disconnected).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a selector is available on a device, it may be pointing to a
clock source which is currently invalid.
If there is a valid clock source which can be selected, switch
to it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the check that parse_audio_format_rates_v2() do after
receiving the clock source entity ID directly into the find
function and add a validation flag to the function.
This patch does not introduce any logic flow change.
It is provided to allow introducing automatic clock switching
easier later. By moving this uac_clock_source_is_valid callsite,
2 additional callsites can be avoided.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the endianness conversions with the kernel-wide swabbing macros
in get/set_sample_rate_v2.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct spelling of snd_usb_endpoint_implict_feedback_sink in all
occurances.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor style fix, following a general code style in the kernel.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().
No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge back for-linus branch for the badness table adjustment for VIA codecs
* for-linus:
ALSA: hda - Fix DAC assignment for independent HP
ALSA: hda - Fix abuse of snd_hda_lock_devices() for DSP loader
ALSA: hda - Fix typo in checking IEC958 emphasis bit
ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()
ALSA: snd-usb: mixer: propagate errors up the call chain
ALSA: usb: Parse UAC2 extension unit like for UAC1
ALSA: hda - Fix yet missing GPIO/EAPD setup in cirrus driver
Creation of individual mixer controls may fail, but that shouldn't cause
the entire mixer creation to fail. Even worse, if the mixer creation
fails, that will error out the entire device probing.
All the functions called by parse_audio_unit() should return -EINVAL if
they find descriptors that are unsupported or believed to be malformed,
so we can safely handle this error code as a non-fatal condition in
snd_usb_mixer_controls().
That fixes a long standing bug which is commonly worked around by
adding quirks which make the driver ignore entire interfaces. Some of
them might now be unnecessary.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Rodolfo Thomazelli <pe.soberbo@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In check_input_term() and parse_audio_feature_unit(), propagate the
error value that has been returned by a failing function instead of
-EINVAL. That helps cleaning up the error pathes in the mixer.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UAC2_EXTENSION_UNIT_V2 differs from UAC1_EXTENSION_UNIT, but can be handled in
the same way when parsing the unit. Otherwise parse_audio_unit() fails when it
sees an extension unit on a UAC2 device.
UAC2_EXTENSION_UNIT_V2 is outside the range allocated by UAC1.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"Playback Design" products need a 50ms delay after setting the USB
interface.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UAC2 compliant audio devices may announce the capability to transport
raw audio data on their endpoints. Catch this and handle it as
'special' stream on the ALSA side.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This field may use up to 32 bits, so it should be handled as unsigned
int.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The maxpacksize field is given in some quirks, but it gets ignored (in
favour of wMaxPacketSize from the first endpoint.) This patch favours
the one in the quirk.
Digidesign Mbox and Mbox 2 are the only affected quirks and the devices
are assumed to be working without this patch. So for safety against the
values in the quirk being incorrect, remove them.
The datainterval is also ignored but there are not currently any quirks
which choose to override this.
Cc: Damien Zammit <damien@zamaudio.com>
Cc: Chris J Arges <christopherarges@gmail.com>
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware also has a PCM capture device which is not implemented in
this patch.
It may be possible to generalise this to Saffire 6 USB support and some
of the other Focusrite interfaces, but as I don't have access to these
devices we should wait until capture support is working first.
Capture support is not implemented because the code assumes the endpoint
to have its own interface (instead, it shares the interface with playback)
and some thought will be needed to lift this limitation.
Signed-off-by: Mark Hills <mark@xwax.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The NuForce UDH-100 numbers its interfaces incorrectly, which makes the
interface associations come out wrong, which results in the driver
erroring out with the message "Audio class v2 interfaces need an
interface association".
Work around this by searching for the interface association descriptor
also in some other place where it might have ended up.
Reported-and-tested-by: Dave Helstroom <helstroom@google.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix three smatch warnings recently introduced:
sound/usb/caiaq/device.c:166 usb_ep1_command_reply_dispatch() warn:
variable dereferenced before check 'cdev' (see line 163)
sound/usb/caiaq/device.c:517 snd_disconnect() warn: variable
dereferenced before check 'card' (see line 514)
sound/usb/caiaq/input.c:510 snd_usb_caiaq_ep4_reply_dispatch() warn:
variable dereferenced before check 'cdev' (see line 506)
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Get rid of the proprietary functions log() and debug() and use the
generic dev_*() approach. A macro is needed to cast a cdev to a struct
device *.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is needed in order to make the device namespace cleaner, and will
help when moving this driver over to dev_*() logging.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
bootresponse in snd_usb_mbox2_boot_quirk is only 12 (decimal) u8's
long, but i9s passed to snd_usb_ctl_msg as it would be 0x12 (hexa)
long. Fix that by having proper size of the array, i.e. 0x12.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds quirks and mixer support for the M-Audio Fast Track C600 USB
audio interface. This device is very similar to the C400 - the C600
simply has some more inputs and outputs, so the existing C400 support
is extended to support this device as well.
Signed-off-by: Matt Gruskin <matthew.gruskin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk for the Roland/Cakewalk A-PRO keyboards accidentally used the
wrong interface number, which prevented the driver from attaching to the
device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: 2.6.37+ <stable@vger.kernel.org>
It looks like MODULE_SUPPORTED_DEVICES() is not implemented yet, but
still, having the entries in the list consistently separated by commas
and with balanced parenthesis won't hurt.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 23caaf19b1 (ALSA: usb-mixer: Add support for Audio Class v2.0)
forgot to adjust the length check for UAC 2.0 feature unit descriptors.
This would make the code abort on encountering a feature unit without
per-channel controls, and thus prevented the driver to work with any
device having such a unit, such as the RME Babyface or Fireface UCX.
Reported-by: Florian Hanisch <fhanisch@uni-potsdam.de>
Tested-by: Matthew Robbetts <wingfeathera@gmail.com>
Tested-by: Michael Beer <beerml@sigma6audio.de>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: 2.6.35+ <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Because currently snd_printd() and snd_printdd() macros are expanded
to empty when CONFIG_SND_DEBUG=n, a compile warning like below
appears sometimes, and we had to covert it by ugly ifdefs:
sound/pci/hda/patch_sigmatel.c: In function ‘stac92hd71bxx_fixup_hp’:
sound/pci/hda/patch_sigmatel.c:2434:24: warning: unused variable ‘spec’ [-Wunused-variable]
For "fixing" these issues better, this patch replaces snd_printd() and
snd_printdd() definitions with empty inline functions instead of
macros. This should have the same effect but shut up warnings like
above.
But since we had already put ifdefs, changing to inline functions
would trigger compile errors. So, such ifdefs is removed in this
patch.
In addition, snd_pci_quirk name field is defined only when
CONFIG_SND_DEBUG_VERBOSE is set, and the reference to it in
snd_printdd() argument triggers the build errors, too. For avoiding
these errors, introduce a new macro snd_pci_quirk_name() that is
defined no matter how the debug option is set.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add names of the clock sources for the M-Audio Fast Track
C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attain constant real-world latency by skipping 16 data packets.
The number of packets to be skipped was found by trial and error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Taking another look at the C400 descriptors, I see now that there is
a clock selector (0x80) for this device.
Right now, the clock source points to the internal clock (0x81), which
is also valid. When the external clock source (0x82) is selected in the
mixer, and the rates mismatch (if it's free-running it is fixed to
48KHz), xruns will occur.
Set the clock ID to the clock selector unit (0x81), which then
allows the validation code to function correctly.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [0d9741c0: ALSA: usb-audio: sync ep init fix for
audioformat mismatch] introduced the correction of parameters to be
set for sync EP. But since the new code assumes that the sync EP is
always paired with the data EP of another direction, it triggers Oops
when a device only with a single direction is used.
This patch adds a proper check of sync EP type and the presence of the
paired substream for avoiding the crash.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the following sparse warning:
sound/usb/mixer_quirks.c:1209:23: warning:
symbol 'ebox44_table' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is based on 3.8-rc1. It fixes two things:
1) A kernel panic caused by incorrect allocation of a u8 variable
"bootresponse".
2) A noisy dmesg (urb status -32) caused by broken pipe to an
invalid midi endpoint.
It is also a little cleaner because there is no need for a new
QUIRK_MIDI type as suggested by kernel developers, since the device
follows exactly the MIDIMAN protocol.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support the Creative BT-D1 Bluetooth USB audio device. Before this
patch, Linux had trouble finding the correct USB descriptors and bailed
out with these messages:
no or invalid class specific endpoint descriptor
Now it still prints these messages on hotplug:
snd-usb-audio: probe of ...:1.0 failed with error -5
snd-usb-audio: probe of ...:1.2 failed with error -5
snd-usb-audio: probe of ...:1.3 failed with error -5
But the device works correctly, including the HID support.
The patch is diff'ed against 3.8-rc1 but should apply to older kernels
as well.
Signed-off-by: Alexander Schremmer <alex@alexanderweb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable delay report on capture path. The delay is reset when an
URB is retired and increment at each call to .pointer based
on frame counter changes. The precision of the delay
information is limited to 1ms as in the playback case.
This reverts commit 3f94fad095.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This update contains overall only driver-specific fixes.
Slightly large LOC are seen in usb-audio driver for a couple of new
device quirks and cs42l71 ASoC driver for enhanced features.
The others are a few small (regression) fixes HD-audio, and yet other
small / trival ASoC fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JoY5
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
This patch is the result of a lot of trial and error, since there are no specs
available for the device.
Full duplex support is provided, i.e. playback and recording in stereo.
The format is hardcoded at 48000Hz @ 24 bit, which is the maximum that the
device supports. Also, MIDI in and MIDI out both work.
Users will notice that the S/PDIF light also flashes when playback or recording
is active. I believe this means that S/PDIF input/output is simultaneously
activated with the analogue i/o during use.
But this particular functionality remains untested.
Note that this particular version of the patch is so far untested on the
physical hardware because I have not compiled a full kernel with the changes.
However, extensive testing has been done by many users of the hardware
who believe other versions of my patch have worked since circa 2009.
[Modified to make a function static by tiwai]
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As Joe Cooper <swelljoe@gmail.com> reported, "On most HP Envy laptops
the snd-usb-audio module causes the system to become unresponsive and
Gnome Shell 3 to crash.".
See also:
http://mailman.alsa-project.org/pipermail/alsa-devel/2012-December/057729.html
Add a quirk to ignore this device (for now) to solve the instability
issue and allow other USB audio devices to be used.
Reported-by: Joe Cooper <swelljoe@gmail.com>
Tested-by: Isaac Smith <hunternet93@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial branch from Jiri Kosina:
"Usual stuff -- comment/printk typo fixes, documentation updates, dead
code elimination."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
HOWTO: fix double words typo
x86 mtrr: fix comment typo in mtrr_bp_init
propagate name change to comments in kernel source
doc: Update the name of profiling based on sysfs
treewide: Fix typos in various drivers
treewide: Fix typos in various Kconfig
wireless: mwifiex: Fix typo in wireless/mwifiex driver
messages: i2o: Fix typo in messages/i2o
scripts/kernel-doc: check that non-void fcts describe their return value
Kernel-doc: Convention: Use a "Return" section to describe return values
radeon: Fix typo and copy/paste error in comments
doc: Remove unnecessary declarations from Documentation/accounting/getdelays.c
various: Fix spelling of "asynchronous" in comments.
Fix misspellings of "whether" in comments.
eisa: Fix spelling of "asynchronous".
various: Fix spelling of "registered" in comments.
doc: fix quite a few typos within Documentation
target: iscsi: fix comment typos in target/iscsi drivers
treewide: fix typo of "suport" in various comments and Kconfig
treewide: fix typo of "suppport" in various comments
...
The only required change is to extend the existing Xonar U1
mixer quirks to the U3, which seems to be controlled the same
way.
Signed-off-by: Denis Washington <denisw@online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch below prevents the 6fire usb driver going into panic state
when stopping playing. On some systems the urb in handler
(usb6fire_pcm_in_urb_handler) is being called while urbs are being
killed off, this causes the driver to set panic state and can result in
the kernel warning 'URB %p submitted while active'.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 947d299686 , "ALSA: snd-usb:
properly initialize the sync endpoint", while correcting the
initialization of the sync endpoint when opening just the data
endpoint, prevents devices that has a sync endpoint, with a channel
number different than that of the data endpoint, from functioning.
Due to a different channel and period bytes count, attempting to
initialize the sync endpoint will fail at the usb host driver.
For example, when using xhci:
cannot submit urb 0, error -90: internal error
With this patch, if a sync endpoint has multiple audioformats, a
matching audioformat is preferred. An audioformat must be found
with at least one channel and support the requested sample rate
and PCM format, otherwise the stream will not be opened.
If the number of channels differ between the selected audioformat
and the requested format, adjust the period bytes count accordingly.
It is safe to perform the calculation on the basis of the channel
count, since the requested PCM audio format and the rate must be
supported by the selected audioformat.
Cc: Jeffrey Barish <jeff_barish@earthlink.net>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [88a8516a: ALSA: usbaudio: implement USB autosuspend] added
the support of autopm for USB MIDI output, but it didn't take the MIDI
input into account.
This patch adds the following for fixing the autopm:
- Manage the URB start at the first MIDI input stream open, instead of
the time of instance creation
- Move autopm code to the common substream_open()
- Make snd_usbmidi_input_start/_stop() more robust and add the running
state check
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a similar protection against the disconnection race and the
invalid use of usb instance after disconnection, as well as we've done
for the USB audio PCM.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=51201
Reviewd-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A lot of headsets/headphones have a "Speaker" mixer control. This confuses
PulseAudio to think it is a speaker instead of a headphone/headset.
Therfore, we rename it to "Headphone".
We determine if something is a headphone similar to how udev determines
form factor (see 78-sound-card.rules).
BugLink: https://bugs.launchpad.net/bugs/1082357
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback endpoint uses implicit feedback mode, similar
to the M-Audio FTU. Like with the FTU, we need to associate
the sync pipe ourselves.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add ranges for various Fast Track C400 controls, as observed
while using the vendor's mixer control software (res values
are an estimation).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the unit ID and the control as parameters to the creation of the
effect unit control for the M-Audio Fast Track Ultra. This allows the
code to be shared with other devices that use different unit ID and
control, such as the M-Audio Fast Track C400.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code mishandles the case where the device is a UAC2
and the bDescriptorSubtype is a UAC2 Effect Unit (0x07).
It tries to parse it as a Processing Unit (which is similar to two
other UAC1 units with overlapping subtypes), but since the structure
is different (See: 4.7.2.10, 4.7.2.11 in UAC2 standard), the parsing
is done incorrectly and prevents the device from initializing.
For now, just ignore the unit.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, channel IDs exceeding 31 (0x1f) cannot be used.
The channel ID is derived from the cmask. Extending cmask
to a 64-bit type would only allow it to go up to 63 (0x3f).
Some devices have channel IDs exceeding that as well.
To address that, add an offset to the mixer element which
is then accounted for in the UAC set/get functions.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For implicit feedback endpoints, the number of bytes for each packet
is matched by the corresponding synchronizing endpoint.
The size is calculated by taking the actual size and dividing it by
the stride - currently by the endpoint's stride, but we should use the
synchronization source's stride.
This is evident when the number of channels differ between the
synchronization source and the implicitly fed-back endpoint, as with
M-Audio Fast Track C400 - the synchronization source (capture)
has 4 channels, while the implicit feedback mode endpoint has 6.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the support for channel maps of the PCM streams on USB audio
devices. The channel map information is already found in
ChannelConfig descriptor entries, which haven't been referred until
now.
Each chmap entry is added to audioformat list entry and copied to TLV
dynamically instead of creating a whole chmap array.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a playback stream is paused, the stream isn't actually stopped,
thus we still need to take care of the in-flight data amount for the
delay calculation. Otherwise the value of subs->last_delay is no
longer reliable and can give a bogus value after resuming from pause.
This will result in "delay: estimated XX, actual YY" error messages.
Also, during pause after all in flight data are processed
(i.e. last_delay = 0), we don't have to calculate the actual delay
from the current frame. Give a short path in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It doesn't make sense to calculate the delay for capture streams in
the current implementation. It's always zero, so we should skip the
computation in snd_usb_pcm_pointer() in the case of capture.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jeffrey Barish reported an obvious bug in the pcm part of the usb-audio
driver which causes the code to not initialize the sync endpoint from
configure_endpoint().
Reported-by: Jeffrey Barish <jeff_barish@earthlink.net>
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
PCM hw_free and close should wait until all the pending stop
operations have been finished. Basically only PCM trigger callback
should use non-wait calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As we are stopping the endpoints asynchronously now, it's better to
trigger the stop of both data and sync endpoints and wait for pending
stopping operations, instead of the sequential trigger-and-wait
procedure.
So the wait argument in snd_usb_endpoint_stop() is dropped, and it's
expected that the caller synchronizes explicitly by calling
snd_usb_endpoint_sync_pending_stop(). (Actually there is only one
place calling this, so it was safe to change.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For further code simplification, drop the conditional call for
usb_kill_urb() with can_wait argument in deactivate_urbs(), and use
only usb_unlink_urb() and wait_clear_urbs() pairs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reduce the redundant arguments for snd_usb_endpoint_start() and
snd_usb_endpoint_stop(). Also replaced from int to bool.
No functional changes by this commit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The async unlink behavior has been working over years. The option was
provided only as a workaround for 2.4.x kernel. Let's get rid of it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'rt' was dereferenced before the NULL check.
Moved the code after the check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"Whether" is misspelled in various comments across the tree; this
fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 88a8516a21 (ALSA: usbaudio: implement USB autosuspend) added
autosuspend code to all files making up the snd-usb-audio driver.
However, midi.c is part of snd-usb-lib and is also used by other
drivers, not all of which support autosuspend. Thus, calls to
usb_autopm_get_interface() could fail, and this unexpected error would
result in the MIDI output being completely unusable.
Make it work by ignoring the error that is expected with drivers that do
not support autosuspend.
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Reported-by: Devin Venable <venable.devin@gmail.com>
Reported-by: Dr Nick Bailey <nicholas.bailey@glasgow.ac.uk>
Reported-by: Jannis Achstetter <jannis_achstetter@web.de>
Reported-by: Rui Nuno Capela <rncbc@rncbc.org>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: 2.6.39+ <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Use bitmap_weight to count the total number of bits set in bitmap.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent change for USB-audio disconnection race fixes introduced a
mutex deadlock again. There is a circular dependency between
chip->shutdown_rwsem and pcm->open_mutex, depicted like below, when a
device is opened during the disconnection operation:
A. snd_usb_audio_disconnect() ->
card.c::register_mutex ->
chip->shutdown_rwsem (write) ->
snd_card_disconnect() ->
pcm.c::register_mutex ->
pcm->open_mutex
B. snd_pcm_open() ->
pcm->open_mutex ->
snd_usb_pcm_open() ->
chip->shutdown_rwsem (read)
Since the chip->shutdown_rwsem protection in the case A is required
only for turning on the chip->shutdown flag and it doesn't have to be
taken for the whole operation, we can reduce its window in
snd_usb_audio_disconnect().
Reported-by: Jiri Slaby <jslaby@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Probing this device currently fails in snd_usb_audio_probe() because
the call to snd_usb_create_mixer() fails. This is due to unknown or
non-standard interface descriptor subtypes in parse_audio_unit():
usbaudio: unit 51: unexpected type 0x09
snd-usb-audio: probe of 1-8:1.0 failed with error -5
Some people are working around this by recompiling usb-audio with the
call to snd_usb_create_mixer() commented out. It would be nice to
avoid that.
While the best idea would be to look into the mixer creation failure,
a reasonable short-term solution is to use quirks to only probe the
trouble-free interfaces. This allows audio and MIDI interfaces to be
used without any obvious issues.
Interface 0 is the main one to ignore. It contains lots of
control-fu, including the unexpected interface descriptor subtypes.
Interface 5 is for firmware updates and I'm not sure how to get
support for this. Interface 3 is some sort of control interface that
I don't understand:
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 1 Audio
bInterfaceSubClass 1 Control Device
bInterfaceProtocol 0
iInterface 0
AudioControl Interface Descriptor:
bLength 9
bDescriptorType 36
bDescriptorSubtype 1 (HEADER)
bcdADC 1.00
wTotalLength 9
bInCollection 1
baInterfaceNr( 0) 1
Signed-off-by: Martin Schwenke <martin@meltin.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are bug reports of a crash with USB-audio devices when PCM
prepare is performed immediately after the stream is stopped via
trigger callback. It turned out that the problem is that we don't
wait until all URBs are killed.
This patch adds a new function to synchronize the pending stop
operation on an endpoint, and calls in the prepare callback for
avoiding the crash above.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=49181
Reported-and-tested-by: Artem S. Tashkinov <t.artem@lycos.com>
Cc: <stable@vger.kernel.org> [v3.6]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similar like the previous commit, cover with chip->shutdown_rwsem
and chip->shutdown checks.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace mutex with rwsem for codec->shutdown protection so that
concurrent accesses are allowed.
Also add the protection to snd_usb_autosuspend() and
snd_usb_autoresume(), too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Close some races at disconnection of a USB audio device by adding the
chip->shutdown_mutex and chip->shutdown check at appropriate places.
The spots to put bandaids are:
- PCM prepare, hw_params and hw_free
- where the usb device is accessed for communication or get speed, in
mixer.c and others; the device speed is now cached in subs->speed
instead of accessing to chip->dev
The accesses in PCM open and close don't need the mutex protection
because these are already handled in the core PCM disconnection code.
The autosuspend/autoresume codes are still uncovered by this patch
because of possible mutex deadlocks. They'll be covered by the
upcoming change to rwsem.
Also the mixer codes are untouched, too. These will be fixed in
another patch, too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Reloop Audio needs a fixed endpoint quirk with S24_3LE format and
UAC_EP_CS_ATTR_SAMPLE_RATE attribute.
Signed-off-by: Didier Villevalois <ptitjes@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without this quirk the VG-99 will work in standard mode (set under
USB on System menu page 2) giving 16 bits at 44.1 Khz audio in/out
but no midi, and is not recognised when set to advanced mode.
After applying this, I can also use the VG-99 in advanced mode: 24
24 bits audio in/out at 44.1 Khz, and midi in/out. Sysex is so far
untested.
In standard mode, the device appears with ID 0x00b3, so the
behaviour isn't affected by this quirk.
Thanks to Clemens Ladisch for simplifying and correcting my initial
attempt!
Signed-off-by: Pete Leigh <pete.leigh@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable ep is initialized but never used
otherwise, so remove the unused variable.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This update contains a few cleanup works, regression/stable fixes
gathered since the last pull request.
- Clean up with generic hd-audio jack handling code by David
Henningsson
- A few regression fixes for standardized HD-audio auto-parser
- Misc clean-up and small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=ehiy
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates #2 from Takashi Iwai:
"This update contains a few cleanup works, regression/stable fixes
gathered since the last pull request.
- Clean up with generic hd-audio jack handling code by David
Henningsson
- A few regression fixes for standardized HD-audio auto-parser
- Misc clean-up and small fixes"
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - do not detect jack on internal speakers for Realtek
ALSA: hda - Fix missing beep on ASUS X43U notebook
ALSA: hda - Remove AZX_DCAPS_POSFIX_COMBO
ALSA: hda - Warn an allocation for an uninitialized array
ALSA: hda/cirrus - Add missing init/free of hda_gen_spec
ALSA: hda - Fix memory leaks at error path in patch_cirrus.c
ALSA: hda - Add missing hda_gen_spec to struct via_spec
ALSA: hda - remove "Mic Jack Mode" for headset jacks (Latitude Exx30)
ALSA: hda - make Cirrus codec use generic unsol event handler
ALSA: hda - make VIA codec use generic unsol event handler
ALSA: hda - Remove dead GPIO code for VIA codec
ALSA: usb-audio: Add TASCAM US122 MKII playback
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
Also fix the calls to next_packet_size() for the pause case. This was
missed in 245baf983 ("ALSA: snd-usb: fix calls to next_packet_size").
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reported-and-tested-by: Christian Tefzer <ctrefzer@gmx.de>
Cc: stable@kernel.org
[ Taking directly because Takashi is on vacation - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While going through Ubuntu bugs, I discovered this patch being
posted and a confirmation that the patch works as expected.
Finding out how the hw volume really works would be preferrable
to just disabling the broken one, but this would be better than
nothing.
Credit: sndfnsdfin (qawsnews)
BugLink: https://bugs.launchpad.net/bugs/559939
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for USB suspend breakage moved the code to set up EP
from hw_params to prepare, but it means also the EP setup might be
called multiple times unnecessarily because the prepare callback can
be called multiple times without starting the stream (e.g. OSS
emulation).
This patch adds a new flag to struct snd_usb_substream indicating
whether the setup of EP is required, and do it only when necessary,
i.e. right after hw_params or suspend.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move interface and endpoint configuration from hw_params to prepare
callback. During system suspend/resume when the USB device power isn't
cycled the interface and endpoint configuration need to be set before
audio playback can continue. Resume involves another call to prepare
but not to hw_params, moving it here allows a playing stream to continue
after resume.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the interface to configure an endpoint so that it doesn't require
a hw_params struct. This will allow it to be called from prepare
instead of hw_params, configuring it after system resume.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the peiod_bytes member of snd_usb_substream. It was no longer being
set, but will be needed to resume properly in a future commit.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for the missing fine delayed time adjustment gives
strange error messages at each start of the playback stream, such as
delay: estimated 0, actual 352
delay: estimated 353, actual 705
These come from the sanity check in retire_playback_urb(). Before the
stream is activated via start_endpoints(), a few silent packets have
been already sent. And at this point the delay account is still in
the state as if the new packets are just queued, so the driver gets
confused and spews the bogus error messages.
For fixing the issue, we just need to check whether the received
packet is valid, whether it's zero sized or not.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Playback Designs' USB devices have some hardware limitations on their
USB interface. In particular:
- They need a 20ms delay after each class compliant request as the
hardware ACKs the USB packets before the device is actually ready
for the next command. Sending data immediately will result in buffer
overflows in the hardware.
- The devices send bogus feedback data at the start of each stream
which confuse the feedback format auto-detection.
This patch introduces a new quirks hook that is called after each
control packet and which adds a delay for all devices that match
Playback Designs' USB VID for now.
In addition, it adds a counter to snd_usb_endpoint to drop received
packets on the floor. Another new quirks function that is called once
an endpoint is started initializes that counter for these devices on
their sync endpoint.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Andreas Koch <andreas@akdesigninc.com>
Supported-by: Demian Martin <demianm_1@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 68e67f40b ("ALSA: snd-usb: move calls to usb_set_interface")
saved us some unnecessary calls to snd_usb_set_interface() but ignored
the fact that there is at least one device out there which operates on
two endpoint in different interfaces simultaniously.
Take care for this by catching the case where data and sync endpoints
are located on different interfaces and calling snd_usb_set_interface()
between the start of the two endpoints.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Robert M. Albrecht <linux@romal.de>
Cc: stable@kernel.org [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to support devices with implicit feedback streaming models,
packet sizes are now stored with each individual urb, and the PCM
handling code which fills the buffers purely relies on the size fields
now.
However, calling snd_usb_audio_next_packet_size() for all possible
packets in an URB at once, prior to letting the PCM code do its job
does in fact not lead to the same behaviour than what the old code did:
The PCM code will break its loop once a period boundary is reached,
consequently using up less packets that it really could.
As snd_usb_audio_next_packet_size() implements a feedback mechanism to
the endpoints phase accumulator, the number of calls to that function
matters, and when called too often, the data rate runs out of bounds.
Fix this by making the next_packet function public, and call it from the
PCM code as before if the packet data sizes are not defined.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Parts of commit 294c4fb8 ("ALSA: usb: refine delay information with USB
frame counter") were unfortunately lost during the refactoring of the
snd-usb driver in 3.5.
This patch adds them back, restoring the correct delay information
behaviour.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usb_endpoint_free() frees the structure that contains its argument.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit e9ba389c5 ("ALSA: usb-audio: Fix scheduling-while-atomic bug in
PCM capture stream") fixed a scheduling-while-atomic bug that happened
when snd_usb_endpoint_start was called from the trigger callback, which
is an atmic context. However, the patch breaks the idea of the endpoints
reference counting, which is the reason why the driver has been
refactored lately.
Revert that commit and let snd_usb_endpoint_start() take care of the URB
cancellation again. As this function is called from both atomic and
non-atomic context, add a flag to denote whether the function may sleep.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A PCM capture stream on usb-audio causes a scheduling-while-atomic
BUG, as reported in the bugzilla entry below. It's because
snd_usb_endpoint_start() is called at first at trigger START for a
capture stream, and this function contains the left-over EP
deactivation codes. The problem doesn't happen for a playback stream
because the function is called at PCM prepare time, which can sleep.
This patch fixes the BUG by moving the EP deactivation code into the
PCM prepare callback.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=46011
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
uac_clock_source_is_valid() uses the control selector value to access
the bmControls bitmap of the clock source unit. This is wrong, as
control selector values start from 1, while the bitmap uses all
available bits.
In other words, "Clock Validity Control" is stored in D3..2, not D5..4
of the clock selector unit's bmControls.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Andreas Koch <andreas@akdesigninc.com>
Cc: stable@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The rework of the snd-usb endpoint logic moved the calls to
snd_usb_set_interface() into the snd_usb_endpoint implemenation. This
changed the order in which these calls are issued to the device, and
thereby caused regressions for some webcams.
Fix this by moving the calls back to pcm.c for now to make it work again
and use snd_usb_endpoint_activate() to really tear down all remaining
URBs in the flight, consequently fixing another regression caused by USB
packets on the wire after altsetting 0 has been selected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Philipp Dreimann <philipp@dreimann.net>
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the new PCM streaming logic, the interface number is assigned to
usb stream instance (subs->interface) after the format and rate setups
are succeeded, but some codes are still passing subs->interface as the
reference to helper functions. This leads to initializing with an
invalid iface number (-1).
This patch replaces the wrong references with the ones from the target
fmt correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the following warning:
CC [M] sound/usb/caiaq/device.o
sound/usb/caiaq/device.c: In function ‘snd_probe’:
sound/usb/caiaq/device.c:500:16: warning: ‘card’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai