Commit Graph

3759 Commits

Author SHA1 Message Date
Srinivas Kandagatla 9d31821fa9 dmaengine: qcom: bam_dma: make bam clk optional
When BAM is remotely controlled it does not sound correct to control
its clk on Linux side. Make it optional, so that its not mandatory
for remote controlled BAM instances.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-03-01 14:14:27 +05:30
Yoshihiro Shimoda d716d9b702 dmaengine: rcar-dmac: fix max_chunk_size for R-Car Gen3
According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-02-27 20:34:38 +05:30
Yang Shunyong 2e67a0875b dmaengine: dmatest: add norandom option
Existing option noverify disables both random src/dst address offset
setup and data verification. Sometimes, we need to control random
src/dst address setup and verification separately, such as disabling
random to make sure that test covers addresses in all interleaving
banks, but data verification is still performed.

This patch adds option norandom to disable random offset setup. Option
noverify has been changed to disable data verification only.

Cc: Joey Zheng <yu.zheng@hxt-semitech.com>
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-02-12 09:16:01 +05:30
Linus Torvalds 367b0df173 Merge branch 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:

 - StrongARM SA1111 updates to modernise and remove cruft

 - Add StrongARM gpio drivers for board GPIOs

 - Verify size of zImage is what we expect to avoid issues with
   appended DTB

 - nommu updates from Vladimir Murzin

 - page table read-write-execute checking from Jinbum Park

 - Broadcom Brahma-B15 cache updates from Florian Fainelli

 - Avoid failure with kprobes test caused by inappropriately
   placed kprobes

 - Remove __memzero optimisation (which was incorrectly being
   used directly by some drivers)

* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
  ARM: 8745/1: get rid of __memzero()
  ARM: 8744/1: don't discard memblock for kexec
  ARM: 8743/1: bL_switcher: add MODULE_LICENSE tag
  ARM: 8742/1: Always use REFCOUNT_FULL
  ARM: 8741/1: B15: fix unused label warnings
  ARM: 8740/1: NOMMU: Make sure we do not hold stale data in mem[] array
  ARM: 8739/1: NOMMU: Setup VBAR/Hivecs for secondaries cores
  ARM: 8738/1: Disable CONFIG_DEBUG_VIRTUAL for NOMMU
  ARM: 8737/1: mm: dump: add checking for writable and executable
  ARM: 8736/1: mm: dump: make the page table dumping seq_file
  ARM: 8735/1: mm: dump: make page table dumping reusable
  ARM: sa1100/neponset: add GPIO drivers for control and modem registers
  ARM: sa1100/assabet: add BCR/BSR GPIO driver
  ARM: 8734/1: mm: idmap: Mark variables as ro_after_init
  ARM: 8733/1: hw_breakpoint: Mark variables as __ro_after_init
  ARM: 8732/1: NOMMU: Allow userspace to access background MPU region
  ARM: 8727/1: MAINTAINERS: Update brcmstb entries to cover B15 code
  ARM: 8728/1: B15: Register reboot notifier for KEXEC
  ARM: 8730/1: B15: Add suspend/resume hooks
  ARM: 8726/1: B15: Add CPU hotplug awareness
  ...
2018-02-02 09:50:51 -08:00
Linus Torvalds 2155e69a9d DMAengine updates for v4.16-rc1
This cycle we have small update for:
   - updates to xilinx and zynqmp dma controllers
   - update reside calculation for rcar controller
   - more RSTify fixes for documentation
   - Add support for race free transfer termination and updating
     for users for that
   - Support for new rev of hidma with addition new APIs to
     get device match data in ACPI/OF
   - Random updates to bunch of other drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJacYHYAAoJEHwUBw8lI4NHWc0P/0oMfdJXSCPbg/Sm/VrTwMR8
 QvWbVxkOdeG/2L4JQYqzuHI1fWFjWV/bCdMqugTfoCs1HGr/JIEcUntM2WLIwCu6
 lF8MjULfOiUieE5SmRj3pvMEKCVYQKVjQpffFRnfnHA7gtU8wpgUYjm9I8dYeat9
 R6JVnqpTL+yrSocjBOZ/PoQy4oboe3TiYH+SOVLZozLUu89+/52i0U+orPYpYXVu
 fu59x8J1YnFxTwNC7RhwTkp1TYW7zse/DtTWQxjJJfxzW+5Gove+VdhmJmfaOQDR
 mJrSzn+dPrFbR6IFs4+XE7ja/lZn5Sjs8vRWktC6/KKQrkUlxOYKDyuoLRwZGLEy
 hCLJo7FRt4n4jV25P4mJB1p9ePOHfzxSD/myXF6o81fX8haBJMr9SmSnWBeiYJpe
 ybz+AvYHn7sDW8WwHJzyuN4WJgDcSkWHqNzx2kjF1k3sYNYqMN4W94+9VIx6oxrI
 fucyry6dNAL9wYEfF8hlnH/3A3PKpWs4zE+trxrCnrj3hvzo3pTbhH+/fhqhR+Wk
 PRoD+yVTVZcPR2F9lysqDX26Rpbq6yHv5IqCyDjnwDuLqwF5yzIODgJ/glkQ1D+F
 bpzVN7BJyz0MMGSQX7ExMcw7PHgnycVW/rNBLVZ6QtBuc1BaYQHdqIpXqzwQr+4T
 8ewXGx5EVqCyYVnDty4y
 =7bH/
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:
 "This time is smallish update with updates mainly to drivers:

   - updates to xilinx and zynqmp dma controllers

   - update reside calculation for rcar controller

   - more RSTify fixes for documentation

   - add support for race free transfer termination and updating for
     users for that

   - support for new rev of hidma with addition new APIs to get device
     match data in ACPI/OF

   - random updates to bunch of other drivers"

* tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (47 commits)
  dmaengine: dmatest: fix container_of member in dmatest_callback
  dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
  dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
  dmaengine: qcom_hidma: simplify DT resource parsing
  dmaengine: xilinx_dma: Free BD consistent memory
  dmaengine: xilinx_dma: Fix warning variable prev set but not used
  dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
  dmaengine: doc: format struct fields using monospace
  dmaengine: doc: fix bullet list formatting
  dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
  dmaengine: cppi41: Fix channel queues array size check
  dmaengine: imx-sdma: Add MODULE_FIRMWARE
  dmaengine: xilinx_dma: Fix typos
  dmaengine: xilinx_dma: Differentiate probe based on the ip type
  dmaengine: xilinx_dma: fix style issues from checkpatch
  dmaengine: xilinx_dma: Fix kernel doc warnings
  dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
  dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
  dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
  dmaengine: zynqmp_dma: Fix race condition in the probe
  ...
2018-01-31 11:52:20 -08:00
Vinod Koul 330542fc1c Merge branch 'topic/xilinx' into for-linus 2018-01-31 13:51:32 +05:30
Vinod Koul b8e1a96359 Merge branch 'topic/virt-dma' into for-linus 2018-01-31 13:51:26 +05:30
Vinod Koul cea0dd4d96 Merge branch 'topic/timb' into for-linus 2018-01-31 13:51:21 +05:30
Vinod Koul db90305b1f Merge branch 'topic/ti' into for-linus 2018-01-31 13:51:16 +05:30
Vinod Koul 21359a84a0 Merge branch 'topic/tegra' into for-linus 2018-01-31 13:51:11 +05:30
Vinod Koul 6811837d53 Merge branch 'topic/stm' into for-linus 2018-01-31 13:51:06 +05:30
Vinod Koul 581f5b1431 Merge branch 'topic/sprd' into for-linus 2018-01-31 13:50:52 +05:30
Vinod Koul 5039104f37 Merge branch 'topic/rcar' into for-linus 2018-01-31 13:50:47 +05:30
Vinod Koul 2cb1800ccf Merge branch 'topic/qcom_hidma' into for-linus 2018-01-31 13:50:40 +05:30
Vinod Koul c203f677c0 Merge branch 'topic/qcom' into for-linus 2018-01-31 13:50:35 +05:30
Vinod Koul c4cc2c3a24 Merge branch 'topic/mic' into for-linus 2018-01-31 13:50:29 +05:30
Vinod Koul bcf73a7b30 Merge branch 'topic/imx' into for-linus 2018-01-31 13:50:25 +05:30
Vinod Koul 1eac32184d Merge branch 'topic/cppi' into for-linus 2018-01-31 13:49:40 +05:30
Linus Torvalds d772794637 Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
 "The main RCU changes in this cycle were:

   - Updates to use cond_resched() instead of cond_resched_rcu_qs()
     where feasible (currently everywhere except in kernel/rcu and in
     kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
     offline CPUs.

   - Updates to simplify RCU's dyntick-idle handling.

   - Updates to remove almost all uses of smp_read_barrier_depends() and
     read_barrier_depends().

   - Torture-test updates.

   - Miscellaneous fixes"

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
  torture: Save a line in stutter_wait(): while -> for
  torture: Eliminate torture_runnable and perf_runnable
  torture: Make stutter less vulnerable to compilers and races
  locking/locktorture: Fix num reader/writer corner cases
  locking/locktorture: Fix rwsem reader_delay
  torture: Place all torture-test modules in one MAINTAINERS group
  rcutorture/kvm-build.sh: Skip build directory check
  rcutorture: Simplify functions.sh include path
  rcutorture: Simplify logging
  rcutorture/kvm-recheck-*: Improve result directory readability check
  rcutorture/kvm.sh: Support execution from any directory
  rcutorture/kvm.sh: Use consistent help text for --qemu-args
  rcutorture/kvm.sh: Remove unused variable, `alldone`
  rcutorture: Remove unused script, config2frag.sh
  rcutorture/configinit: Fix build directory error message
  rcutorture: Preempt RCU-preempt readers more vigorously
  torture: Reduce #ifdefs for preempt_schedule()
  rcu: Remove have_rcu_nocb_mask from tree_plugin.h
  rcu: Add comment giving debug strategy for double call_rcu()
  tracing, rcu: Hide trace event rcu_nocb_wake when not used
  ...
2018-01-30 10:15:30 -08:00
Yang Shunyong 66b3bd2356 dmaengine: dmatest: fix container_of member in dmatest_callback
The type of arg passed to dmatest_callback is struct dmatest_done.
It refers to test_done in struct dmatest_thread, not done_wait.

Fixes: 6f6a23a213 ("dmaengine: dmatest: move callback wait ...")
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Acked-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-30 12:24:43 +05:30
Russell King 3a175cdf43 Merge branches 'fixes', 'misc', 'sa1111' and 'sa1100-for-next' into for-next 2018-01-21 15:38:10 +00:00
Nicolas Pitre ff5fdafc9e ARM: 8745/1: get rid of __memzero()
The __memzero assembly code is almost identical to memset's except for
two orr instructions. The runtime performance of __memset(p, n) and
memset(p, 0, n) is accordingly almost identical.

However, the memset() macro used to guard against a zero length and to
call __memzero at compile time when the fill value is a constant zero
interferes with compiler optimizations.

Arnd found tha the test against a zero length brings up some new
warnings with gcc v8:

  https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82103

And successively rremoving the test against a zero length and the call
to __memzero optimization produces the following kernel sizes for
defconfig with gcc 6:

    text     data     bss       dec       hex  filename
12248142  6278960  413588  18940690   1210312  vmlinux.orig
12244474  6278960  413588  18937022   120f4be  vmlinux.no_zero_test
12239160  6278960  413588  18931708   120dffc  vmlinux.no_memzero

So it is probably not worth keeping __memzero around given that the
compiler can do a better job at inlining trivial memset(p,0,n) on its
own. And the memset code already handles a zero length just fine.

Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2018-01-21 15:37:56 +00:00
Wei Yongjun 2cbe23f8fc dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
devm_ioremap_resource() already checks if the resource is NULL, so
remove the unnecessary platform_get_resource() error check.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-19 11:07:50 +05:30
Rafael J. Wysocki 4b67157f04 Merge branch 'pm-core'
* pm-core: (29 commits)
  dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
  PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
  PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
  PM / runtime: Rework pm_runtime_force_suspend/resume()
  PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
  PM / core: Propagate wakeup_path status flag in __device_suspend_late()
  PM / core: Re-structure code for clearing the direct_complete flag
  PM: i2c-designware-platdrv: Optimize power management
  PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
  PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
  PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
  PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
  PM / core: Assign the wakeup_path status flag in __device_prepare()
  PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
  PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
  PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
  PM / core: Add helpers for subsystem callback selection
  PM / wakeup: Drop redundant check from device_init_wakeup()
  PM / wakeup: Drop redundant check from device_set_wakeup_enable()
  PM / wakeup: only recommend "call"ing device_init_wakeup() once
  ...
2018-01-18 02:55:09 +01:00
Geert Uytterhoeven 1131b0a4af dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
The current (empty) system sleep callbacks rely on the PM core to force
a runtime resume to reinitialize the DMAC registers during system
resume.  Without a reinitialization, e.g. SCIF DMA will hang silently
after a system resume on R-Car Gen3.

Make this explicit by using pm_runtime_force_{suspend,resume}() as the
system sleep callbacks instead.  Use SET_LATE_SYSTEM_SLEEP_PM_OPS() as
DMA engines must be initialized before all DMA slave devices.

Fixes: 17218e0092 "PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()"
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-01-17 12:46:18 +01:00
Vinod Koul 1ab8da1182 dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
Sparse warns that 'sprd_dma_prep_dma_memcpy' should be static so make it
static.

drivers/dma/sprd-dma.c:713:32: warning:
symbol'sprd_dma_prep_dma_memcpy' was not declared. Should it be static?

Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-15 11:33:11 +05:30
Rob Herring 37fa4905d2 dmaengine: qcom_hidma: simplify DT resource parsing
The hidma driver open codes populating address and IRQ resources from DT.
We have standard functions of_address_to_resource and of_irq_to_resource
for this, so use them instead.

The DT binding states each child should have 2 addresses and 1 IRQ, so we
can simplify the logic and do a fixed size resource allocation. Using the
standard of_address_to_resource will also do any address translation which
was missing.

Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-08 22:31:02 +05:30
Kedareswara rao Appana 0e847d44b3 dmaengine: xilinx_dma: Free BD consistent memory
Free BD consistent memory while freeing the channel
i.e in free_chan_resources.

Signed-off-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-08 16:24:50 +05:30
Kedareswara rao Appana 4b597c634a dmaengine: xilinx_dma: Fix warning variable prev set but not used
This patch fixes the below sparse warning in the driver
drivers/dma/xilinx/xilinx_dma.c: In function ‘xilinx_vdma_dma_prep_interleaved’:
drivers/dma/xilinx/xilinx_dma.c:1614:43: warning: variable ‘prev’ set but not used [-Wunused-but-set-variable]
  struct xilinx_vdma_tx_segment *segment, *prev = NULL;

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-08 16:24:50 +05:30
Kedareswara rao Appana 48c62fb051 dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
If the hardware is configured for Scatter Gather(SG) mode,
and hardware is idle, in the control register SG mode bit
must be set to a 0 then back to 1 by the software, to force
the CDMA SG engine to use a new value written to the CURDESC_PNTR
register, failure to do so could result errors from the dmaengine.

This patch updates the same.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2018-01-08 16:24:50 +05:30
Ingo Molnar 475c5ee193 Merge branch 'for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
Pull RCU updates from Paul E. McKenney:

- Updates to use cond_resched() instead of cond_resched_rcu_qs()
  where feasible (currently everywhere except in kernel/rcu and
  in kernel/torture.c).  Also a couple of fixes to avoid sending
  IPIs to offline CPUs.

- Updates to simplify RCU's dyntick-idle handling.

- Updates to remove almost all uses of smp_read_barrier_depends()
  and read_barrier_depends().

- Miscellaneous fixes.

- Torture-test updates.

Signed-off-by: Ingo Molnar <mingo@kernel.org>
2018-01-03 14:14:18 +01:00
Vignesh R d087f15786 dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
Register layout of a typical TPCC_EVT_MUX_M_N register is such that the
lowest numbered event is at the lowest byte address and highest numbered
event at highest byte address. But TPCC_EVT_MUX_60_63 register layout is
different,  in that the lowest numbered event is at the highest address
and highest numbered event is at the lowest address. Therefore, modify
ti_am335x_xbar_write() to handle TPCC_EVT_MUX_60_63 register
accordingly.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-22 17:48:07 +05:30
Gomonovych, Vasyl 5a358f50c3 dmaengine: cppi41: Fix channel queues array size check
The test should be >= ARRAY_SIZE() instead of > ARRAY_SIZE().

Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-22 17:47:04 +05:30
Nicolas Chauvet c0879342ef dmaengine: imx-sdma: Add MODULE_FIRMWARE
This avoid the following error when using an initramfs on wandboard quad
Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2

Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-22 17:35:44 +05:30
Vinod Koul 3093186898 dmaengine: xilinx_dma: Fix typos
some typos is comments, so fix them up
/s/enusres/ensures
/s/descripotrs/descriptors
/s/Submited/Submitted
/s/pollling/polling

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:48:08 +05:30
Kedareswara rao Appana c7a03599b5 dmaengine: xilinx_dma: Differentiate probe based on the ip type
This patch updates the probe banner info based on the ip probed.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:44:09 +05:30
Kedareswara rao Appana 22653af70e dmaengine: xilinx_dma: fix style issues from checkpatch
This patch fixes below.
ERROR: open brace '{' following function definitions go on the next line
+static int xilinx_dma_child_probe(struct xilinx_dma_device *xdev,
+				    struct device_node *node) {

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:44:09 +05:30
Kedareswara rao Appana e50a0ad159 dmaengine: xilinx_dma: Fix kernel doc warnings
This patch fixes the kernel doc warnings
in the driver.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:44:09 +05:30
Kedareswara rao Appana 23059408b6 dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
As per axi dmaengine spec the software must not move the tail pointer
to a location that has not been updated (next descriptor field of the
h/w descriptor should always point to a valid address).

When user submits multiple descriptors on the recv side, with the
current driver flow the last buffer descriptor next descriptor field
points to a invalid location, resulting the invalid data or errors from the
axidma dmaengine.

This patch fixes this issue by creating a buffer descritpor chain during
channel allocation itself and use those buffer descriptors for the
subsequent dma operations.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:44:09 +05:30
Kedareswara rao Appana fe0503e193 dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
VDMA engine default frame buffer configuration is cirular mode.
in this mode dmaengine continuously circles through h/w configured fstore
frame buffers.

When vdma h/w is configured for more than one frame.
for example h/w is configured for n number of frames, user
submits less than n number of frames and triggered the dmaengine
using issue_pending API.

since the h/w (or) driver default configuraiton is circular mode
h/w tries to write/read from an invalid frame buffer resulting
errors from the vdma dmaengine.

This patch fixes this issue by enabling the park mode as
default mode configuration for frame buffers in s/w,
so that driver can handle all cases for "k" frames where n%k==0
(n is a multiple of k) by simply replicating the frame pointers.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:44:09 +05:30
Kedareswara rao Appana 21e02a3e05 dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
Add variable for checking channel idle state to ensure that dma
descriptor is not submitted when dmaengine is in progress.

This will avoid the polling for a bit in the status register to know
dma state in the driver hot path.

Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 10:44:09 +05:30
Kedareswara rao Appana 5ba080aada dmaengine: zynqmp_dma: Fix race condition in the probe
Incase of interrupt property is not present,
Driver is trying to free an invalid irq,
This patch fixes it by adding a check before freeing the irq.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 09:37:06 +05:30
Kedareswara rao Appana 8d90035e37 dmaengine: zynqmp_dma: Fix issues with overflow interrupt
This patch fixes the below issues.
--> Need to clear the channel data count register
when overflow interrupts occurs.
--> Reduce the log level from _info to _dbg when
overflow interrupt occurs.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 09:37:06 +05:30
Kedareswara rao Appana 3c48d62de2 dmaengine: zynqmp_dma: Fix warning variable 'val' set but not used
This patch fixes the below warning

drivers/dma/xilinx/zynqmp_dma.c: In function 'zynqmp_dma_handle_ovfl_int':
drivers/dma/xilinx/zynqmp_dma.c:522:6: warning: variable 'val' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 09:37:06 +05:30
Kedareswara rao Appana 30df4574e4 dmaengine: zynqmp_dma: Fix kernel doc-format
This patch fixes the below kernel doc warnings
drivers/dma/xilinx/zynqmp_dma.c:552: info: Scanning doc for
zynqmp_dma_device_config
drivers/dma/xilinx/zynqmp_dma.c:558: warning: No description found for
return value of 'zynqmp_dma_device_config'
drivers/dma/xilinx/zynqmp_dma.c:649: info: Scanning doc for
zynqmp_dma_free_descriptors
drivers/dma/xilinx/zynqmp_dma.c:653: warning: No description found for
parameter 'chan'
drivers/dma/xilinx/zynqmp_dma.c:653: warning: Excess function parameter
'dchan' description in 'zynqmp_dma_free_descriptors'

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 09:37:06 +05:30
Kedareswara rao Appana 64c6f7da8c dmaengine: zynqmp_dma: Add runtime pm support
This patch adds runtime pm support in the driver.

Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-18 09:28:09 +05:30
Andreas Platschek 2610acf46b dmaengine: fsl-edma: disable clks on all error paths
Previously enabled clks are only disabled if clk_prepare_enable() fails.
However, there are other error paths were the previously enabled
clocks are not disabled.

To fix the problem, fsl_disable_clocks() now takes the number of clocks
that shall be disabled + unprepared. For existing calls were all clocks
were already successfully prepared + enabled, DMAMUX_NR is passed to
disable + unprepare all clocks.

In error paths were only some clocks were successfully prepared +
enabled the loop counter is passed, in order to disable + unprepare
all successfully prepared + enabled clocks.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-15 09:53:04 +05:30
Sinan Kaya b5419adcda dmaengine: qcom_hidma: Add identity register support
The location for destination event channel register has been relocated from
offset 0x28 to 0x40. Update the code accordingly.

Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-13 14:12:10 +05:30
Sinan Kaya 95fbfb7aa2 dmaengine: qcom_hidma: Add support for the new revision
Add support for probing the newer HW and also organize MSI capable hardware
into an array for maintenance reasons.

Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-13 14:12:10 +05:30
Sinan Kaya 38680bc6b1 dmaengine: qcom_hidma: check pending interrupts
Driver is missing the interrupts if two requests are queued up at the same
time as the interrupt handler is servicing a request that was just
delivered.

The ISR clears the interrupt at the end but it could be clearing the
interrupt for an outstanding event. Therefore, second interrupt never
arrives.

Clear the interrupt first and then check for completions.

Also, make sure that request start and interrupt clear do not overlap in
time by using a spinlock.

Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-12 11:02:43 +05:30
Tobias Jordan eb9436966f dmaengine: jz4740: disable/unprepare clk if probe fails
in error path of jz4740_dma_probe(), call clk_disable_unprepare() to clean
up.

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 25ce6c35fe MIPS: jz4740: Remove custom DMA API
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-11 09:00:06 +05:30
Colin Ian King dd54006fed dmaengine: timb_dma: fix spelling mistake: "Couldnt" -> "Couldn't"
Trivial fix to spelling mistake in dev_err error message text.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-11 08:57:38 +05:30
Adam Wallis 6f6a23a213 dmaengine: dmatest: move callback wait queue to thread context
Commit adfa543e73 ("dmatest: don't use set_freezable_with_signal()")
introduced a bug (that is in fact documented by the patch commit text)
that leaves behind a dangling pointer. Since the done_wait structure is
allocated on the stack, future invocations to the DMATEST can produce
undesirable results (e.g., corrupted spinlocks).

Commit a9df21e34b ("dmaengine: dmatest: warn user when dma test times
out") attempted to WARN the user that the stack was likely corrupted but
did not fix the actual issue.

This patch fixes the issue by pushing the wait queue and callback
structs into the the thread structure. If a failure occurs due to time,
dmaengine_terminate_all will force the callback to safely call
wake_up_all() without possibility of using a freed pointer.

Cc: stable@vger.kernel.org
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=197605
Fixes: adfa543e73 ("dmatest: don't use set_freezable_with_signal()")
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Suggested-by: Shunyong Yang <shunyong.yang@hxt-semitech.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-11 08:46:24 +05:30
Paul E. McKenney 98c1ec7cef drivers/dma/ioat: Remove now-redundant smp_read_barrier_depends()
Now that READ_ONCE() implies smp_read_barrier_depends(), the
__cleanup() and ioat_abort_descs() functions no longer need their
smp_read_barrier_depends() calls, which this commit removes.
It is actually not entirely clear why this driver ever included
smp_read_barrier_depends() given that it appears to be x86-only and
given that smp_read_barrier_depends() has no effect whatsoever except
on DEC Alpha.

Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: <dmaengine@vger.kernel.org>
2017-12-05 11:57:53 -08:00
Vasyl Gomonovych a8ffa34fa5 dmaengine: mic_x100_dma: Use PTR_ERR_OR_ZERO()
Fix ptr_ret.cocci warnings:
drivers/dma/mic_x100_dma.c:483:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci

Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:40:38 +05:30
Peter Ujfalusi 2c6929d2ea dmaengine: s3c24xx-dma: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi 3ee7e42f3c dmaengine: k3dma: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi 397c59bce6 dmaengine: img-mdc-dma: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi 47d71bc75d dmaengine: amba-pl08x: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi f0dd52c85d dmaengine: dma-jz4780: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi de92436ac4 dmaengine: bcm2835-dma: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Implement the device_synchronize callback to make sure that the terminated
descriptor is freed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi 174334bcd9 dmaengine: edma: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi b1faf0f564 dmaengine: omap-dma: Use vchan_terminate_vdesc() instead of desc_free
To avoid race with vchan_complete, use the race free way to terminate
running transfer.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi 1c7f072d94 dmaengine: virt-dma: Support for race free transfer termination
Even with the introduced vchan_synchronize() we can face race when
terminating a cyclic transfer.

If the terminate_all is called after the interrupt handler called
vchan_cyclic_callback(), but before the vchan_complete tasklet is called:
vc->cyclic is set to the cyclic descriptor, but the descriptor itself was
freed up in the driver's terminate_all() callback.
When the vhan_complete() is executed it will try to fetch the vc->cyclic
vdesc, but the pointer is pointing now to uninitialized memory leading to
(hard to reproduce) kernel crash.

In order to fix this, drivers should:
- call vchan_terminate_vdesc() from their terminate_all callback instead
calling their free_desc function to free up the descriptor.
- implement device_synchronize callback and call vchan_synchronize().

This way we can make sure that the descriptor is only going to be freed up
after the vchan_callback was executed in a safe manner.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Peter Ujfalusi 6af149d2b1 dmaengine: virt-dma: Add helper to free/reuse a descriptor
The vchan_vdesc_fini() can be used to free or reuse a given descriptor
after it has been marked as completed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-12-04 22:33:51 +05:30
Gustavo A. R. Silva 62a277d43d dmaengine: at_hdmac: fix potential NULL pointer dereference in atc_prep_dma_interleaved
_xt_ is being dereferenced before it is null checked, hence there is a
potential null pointer dereference.

Fix this by moving the pointer dereference after _xt_ has been null
checked.

This issue was detected with the help of Coccinelle.

Fixes: 4483320e24 ("dmaengine: Use Pointer xt after NULL check.")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-29 19:48:17 +05:30
Christophe JAILLET 5c9afbda91 dmaengine: ioat: Fix error handling path
If the last test in 'ioat_dma_self_test()' fails, we must release all
the allocated resources and not just part of them.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-29 19:47:46 +05:30
Kuninori Morimoto 73a47bd0da dmaengine: rcar-dmac: use TCRB instead of TCR for residue
SYS/RT/Audio DMAC includes independent data buffers for reading
and writing. Therefore, the read transfer counter and write transfer
counter have different values.
TCR indicates read counter, and TCRB indicates write counter.
The relationship is like below.

	        TCR       TCRB
	[SOURCE] -> [DMAC] -> [SINK]

In the MEM_TO_DEV direction, what really matters is how much data has
been written to the device. If the DMA is interrupted between read and
write, then, the data doesn't end up in the destination, so shouldn't
be counted. TCRB is thus the register we should use in this cases.

In the DEV_TO_MEM direction, the situation is more complex. Both the
read and write side are important. What matters from a data consumer
point of view is how much data has been written to memory.
On the other hand, if the transfer is interrupted between read and
write, we'll end up losing data. It can also be important to report.

In the MEM_TO_MEM direction, what matters is of course how much data
has been written to memory from data consumer point of view.
Here, because read and write have independent data buffers, it will
take a while for TCR and TCRB to become equal. Thus we should check
TCRB in this case, too.

Thus, all cases we should check TCRB instead of TCR.

Without this patch, Sound Capture has noise after PulseAudio support
(= 07b7acb51d ("ASoC: rsnd: update pointer more accurate")), because
the recorder will use wrong residue counter which indicates transferred
from sound device, but in reality the data was not yet put to memory
and recorder will record it.

However, because DMAC is buffering data until it can be transferable
size, TCRB might not be updated.
For example, if consumer doesn't know how much data can be received,
it requests enough size to DMAC. But in reality, it might receive very
few data. In such case, DMAC just buffered it until transferable size,
and no TCRB updated.

In such case, this buffered data will be transferred if CHCR::DE bit was
cleared, and this is happen if rcar_dmac_chan_halt(). In other word, it
happen when consumer called dmaengine_terminate_all().

Because of this behavior, it need to flush buffered data when it returns
"residue" (= dmaengine_tx_status()).
Otherwise, consumer might calculate wrong things if it called
dmaengine_tx_status() and dmaengine_terminate_all() consecutively.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-29 19:42:57 +05:30
Kuninori Morimoto a8d46a7f5d dmaengine: rcar-dmac: ensure CHCR DE bit is actually 0 after clearing
DMAC reads data from source device, and buffered it until transferable
size for sink device. Because of this behavior, DMAC is including
buffered data .

Now, CHCR DE bit is controlling DMA transfer enable/disable.

If DE bit was cleared during data transferring, or during buffering,
it will flush buffered data if source device was peripheral device
(The buffered data will be removed if source device was memory).
Because of this behavior, driver should ensure that DE bit is actually
0 after clearing.

This patch adds new rcar_dmac_chcr_de_barrier() and call it after CHCR
register access.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Tested-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-29 19:42:57 +05:30
Dmitry Osipenko f6160f3598 dmaengine: tegra-apb: Support non-flow controlled slave configuration
This allows DMA client to issue a non-flow controlled TX. In particular
it is needed for the fuse driver that reads fuse registers using APBDMA
to workaround a HW bug that results in hang when CPU and DMA perform
simultaneous access to fuse peripheral.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-29 19:35:05 +05:30
Linus Torvalds 23c258763b dmaengine updates for 4.15-rc1
Updates for this cycle include:
 - New driver for Spreadtrum dma controller, ST MDMA and DMAMUX controllers
 - PM support for IMG MDC drivers
 - Updates to bcm-sba-raid driver and improvements to sun6i driver
 - Subsystem conversion for:
   - timers to use timer_setup()
   - remove usage of PCI pool API
   - usage of %p format specifier
 - Minor updates to bunch of drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaCn48AAoJEHwUBw8lI4NHTe8P/RpJH8tDat/joT7Hl71stEod
 vKa0iSkW2fdwd6PeaRfd+UTloska1NE9rdgfh8pCVveoHjCPQBVBOC7V8DbMtlsi
 /IlJjFT74wl2R1aSHcSGoLGsIEyurz+9SK88qCU54OQSjVHSnfmyGI4ycTLQGH9U
 zce5JHWHB5MkdftM4eJaSE/t0Md1DBkxadFSQRkwQqqDqoLE7jgJUK0TADRukQqS
 fsDYPh/OhYAizAHlmEGuLZQheN0ld5W7n1sGsEnBD88wtBMvYHzAwT17B+BobxEp
 jyaoE5nV4AgqWh1mvixrmgKoj2KL3DDC+QeoHYCExdcgIrvc86xN3homx9g9y38a
 b99pgDDvXjw4N7S6AmRyQlm/5D0QyjUaoHgGklsaR3ix81dFwDY15aZa8/uQ4EAT
 iKH8DxAgOq6aG1MkUycQ/7QTenRbN4yWQQa+Mm5ncoNU8bpazyxf2l5L9OJWpFjX
 Q6VagNim+plGeUhpJ4IEfPi7LChXFaYsb1D7A/dqpIRvaYzwsy80b/DNhobGMDF6
 eTpny64AKHnozWw/KP5k3DfcYvoU/ytcSsWf8h+CPN7EdLMBqUXFgkVwtyf6WKNc
 UPl+2in08GLgfGb+n2IAdaQzlJ4dK2P7f7mx0T4OvRymu35HXd8nJjmMJ5ZyBr1t
 Z/0JVfcA66AL+XSt179C
 =t9Ix
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-4.15-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:
 "Updates for this cycle include:

   - new driver for Spreadtrum dma controller, ST MDMA and DMAMUX
     controllers

   - PM support for IMG MDC drivers

   - updates to bcm-sba-raid driver and improvements to sun6i driver

   - subsystem conversion for:
      - timers to use timer_setup()
      - remove usage of PCI pool API
      - usage of %p format specifier

   - minor updates to bunch of drivers"

* tag 'dmaengine-4.15-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (49 commits)
  dmaengine: ti-dma-crossbar: Correct am335x/am43xx mux value type
  dmaengine: dmatest: warn user when dma test times out
  dmaengine: Revert "rcar-dmac: use TCRB instead of TCR for residue"
  dmaengine: stm32_mdma: activate pack/unpack feature
  dmaengine: at_hdmac: Remove unnecessary 0x prefixes before %pad
  dmaengine: coh901318: Remove unnecessary 0x prefixes before %pad
  MAINTAINERS: Step down from a co-maintaner of DW DMAC driver
  dmaengine: pch_dma: Replace PCI pool old API
  dmaengine: Convert timers to use timer_setup()
  dmaengine: sprd: Add Spreadtrum DMA driver
  dt-bindings: dmaengine: Add Spreadtrum SC9860 DMA controller
  dmaengine: sun6i: Retrieve channel count/max request from devicetree
  dmaengine: Build bcm-sba-raid driver as loadable module for iProc SoCs
  dmaengine: bcm-sba-raid: Use common GPL comment header
  dmaengine: bcm-sba-raid: Use only single mailbox channel
  dmaengine: bcm-sba-raid: serialize dma_cookie_complete() using reqs_lock
  dmaengine: pl330: fix descriptor allocation fail
  dmaengine: rcar-dmac: use TCRB instead of TCR for residue
  dmaengine: sun6i: Add support for Allwinner A64 and compatibles
  arm64: allwinner: a64: Add devicetree binding for DMA controller
  ...
2017-11-14 16:49:31 -08:00
Vinod Koul cecd5fc551 Merge branch 'topic/xilinx' into for-linus 2017-11-14 10:37:28 +05:30
Vinod Koul 40b4ed1a1a Merge branch 'topic/timer_api' into for-linus 2017-11-14 10:37:18 +05:30
Vinod Koul 8e6c1db351 Merge branch 'topic/ti' into for-linus 2017-11-14 10:37:13 +05:30
Vinod Koul d2045ba3a4 Merge branch 'topic/sun' into for-linus 2017-11-14 10:37:07 +05:30
Vinod Koul 135ab7f53c Merge branch 'topic/sprd' into for-linus
Kconfig and Makefile conflicts so put them in right order (sprd ones after
stm ones)

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-14 10:36:09 +05:30
Vinod Koul 9c60271336 Merge branch 'topic/stm' into for-linus 2017-11-14 10:34:56 +05:30
Vinod Koul 2c8528592c Merge branch 'topic/sa11x0' into for-linus 2017-11-14 10:33:33 +05:30
Vinod Koul b683fa223b Merge branch 'topic/renasas' into for-linus 2017-11-14 10:33:24 +05:30
Vinod Koul c7960fc5e0 Merge branch 'topic/qcom' into for-linus 2017-11-14 10:33:16 +05:30
Vinod Koul 4cd46d0c5e Merge branch 'topic/pl330' into for-linus 2017-11-14 10:33:04 +05:30
Vinod Koul 9427702dcc Merge branch 'topic/imx' into for-linus 2017-11-14 10:32:52 +05:30
Vinod Koul 340b11b9f1 Merge branch 'topic/img' into for-linus 2017-11-14 10:32:49 +05:30
Vinod Koul 76a0370a46 Merge branch 'topic/dmatest' into for-linus 2017-11-14 10:32:36 +05:30
Vinod Koul 575d34b6de Merge branch 'topic/bcom' into for-linus 2017-11-14 10:32:28 +05:30
Vinod Koul 049d0d3849 Merge branch 'topic/axi' into for-linus 2017-11-14 10:32:20 +05:30
Vinod Koul 5ddab696e7 Merge branch 'topic/print_fixes' into for-linus 2017-11-14 10:31:59 +05:30
Peter Ujfalusi 288e7560e4 dmaengine: ti-dma-crossbar: Correct am335x/am43xx mux value type
The used 0x1f mask is only valid for am335x family of SoC, different family
using this type of crossbar might have different number of electable
events. In case of am43xx family 0x3f mask should have been used for
example.
Instead of trying to handle each family's mask, just use u8 type to store
the mux value since the event offsets are aligned to byte offset.

Fixes: 42dbdcc6bf ("dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-08 19:51:40 +05:30
Adam Wallis a9df21e34b dmaengine: dmatest: warn user when dma test times out
Commit adfa543e73 ("dmatest: don't use set_freezable_with_signal()")
introduced a bug (that is in fact documented by the patch commit text)
that leaves behind a dangling pointer. Since the done_wait structure is
allocated on the stack, future invocations to the DMATEST can produce
undesirable results (e.g., corrupted spinlocks). Ideally, this would be
cleaned up in the thread handler, but at the very least, the kernel
is left in a very precarious scenario that can lead to some long debug
sessions when the crash comes later.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=197605
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-08 11:24:03 +05:30
Vinod Koul 087ffdd288 dmaengine: Revert "rcar-dmac: use TCRB instead of TCR for residue"
This reverts commit 847449f23dcb: ("dmaengine: rcar-dmac: use TCRB instead
of TCR for residue") as it breaks small serial console.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-08 11:04:49 +05:30
Pierre-Yves MORDRET d83f4131c2 dmaengine: stm32_mdma: activate pack/unpack feature
If source and destination bus width differs pack/unpack MDMA
feature has to be activated for alignment.
This pack/unpack feature implies to have both source/destination address
and buffer length aligned on bus width.

Fixes: a4ffb13c89 ("dmaengine: Add STM32 MDMA driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-08 10:49:53 +05:30
Vinod Koul 77ea824c6d dmaengine: at_hdmac: Remove unnecessary 0x prefixes before %pad
Since commit 3cab1e7112 ("lib/vsprintf: refactor duplicate code
to special_hex_number()") %pad doesn't need 0x prefix so drop that.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-08 10:47:04 +05:30
Vinod Koul 6d82e05b3c dmaengine: coh901318: Remove unnecessary 0x prefixes before %pad
Since commit 3cab1e7112 ("lib/vsprintf: refactor duplicate code
to special_hex_number()") %pad doesn't need 0x prefix so drop that.

Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-11-08 10:46:46 +05:30
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Romain Perier 10c191a11c dmaengine: pch_dma: Replace PCI pool old API
The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-31 17:01:06 +05:30
Kees Cook bcdc4bd356 dmaengine: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-24 20:11:21 +05:30
Baolin Wang 9b3b8171f7 dmaengine: sprd: Add Spreadtrum DMA driver
This patch adds the DMA controller driver for Spreadtrum SC9860 platform.

Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-24 20:07:55 +05:30
Stefan Brüns 464aa6f54b dmaengine: sun6i: Retrieve channel count/max request from devicetree
To avoid introduction of a new compatible for each small SoC/DMA controller
variation, move the definition of the channel count to the devicetree.

The number of vchans is no longer explicit, but limited by the highest
port/DMA request number. The result is a slight overallocation for SoCs
with a sparse port mapping.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-23 11:44:03 +05:30
Anup Patel 7076a1e4a4 dmaengine: Build bcm-sba-raid driver as loadable module for iProc SoCs
By default, we build Broadcom SBA RAID driver as loadable module for
iProc SOCs so that kernel image is little smaller and we load SBA RAID
driver only when required.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-23 11:35:47 +05:30
Anup Patel d5c334870e dmaengine: bcm-sba-raid: Use common GPL comment header
This patch makes the comment header of Broadcom SBA RAID driver
similar to the GPL comment header used across Broadcom driver
sources.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-23 11:35:47 +05:30
Anup Patel 4e9f8187ae dmaengine: bcm-sba-raid: Use only single mailbox channel
Each mailbox channel used by Broadcom SBA RAID driver is
a separate HW ring.

Currently, Broadcom SBA RAID driver creates one DMA channel
using one or more mailbox channels. When we are using more
than one mailbox channels for a DMA channel, the sba_request
are distributed evenly among multiple mailbox channels which
results in sba_request being completed out-of-order.

The above described out-of-order completion of sba_request
breaks the dma_async_is_complete() API because it assumes
DMA cookies are completed in orderly fashion.

To ensure correct behaviour of dma_async_is_complete() API,
this patch updates Broadcom SBA RAID driver to use only
single mailbox channel. If additional mailbox channels are
specified in DT then those will be ignored.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-23 11:35:47 +05:30
Anup Patel 5d74aa7f64 dmaengine: bcm-sba-raid: serialize dma_cookie_complete() using reqs_lock
As-per documentation in driver/dma/dmaengine.h, the
dma_cookie_complete() API should be called with lock
held.

This patch ensures that Broadcom SBA RAID driver calls
the dma_cookie_complete() API with reqs_lock held.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-23 11:35:47 +05:30
Stefan Roese c5709d3769 dmaengine: altera: Use IRQ-safe spinlock calls in the error paths as well
The patch edf10919 [dmaengine: altera: fix spinlock usage] missed to
change 2 occurrences of spin_unlock_bh() to spin_unlock_irqrestore().
This patch fixes this by moving to the IRQ-safe call in the error
paths as well.

Fixes: edf10919 (dmaengine: altera: fix spinlock usage)
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Sylvain Lesne <lesne@alse-fr.com>
[add fixes tag and fix typo in log]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-20 11:51:10 +05:30
Alexander Kochetkov e588710311 dmaengine: pl330: fix descriptor allocation fail
If two concurrent threads call pl330_get_desc() when DMAC descriptor
pool is empty it is possible that allocation for one of threads will fail
with message:

kernel: dma-pl330 20078000.dma-controller: pl330_get_desc:2469 ALERT!

Here how that can happen. Thread A calls pl330_get_desc() to get
descriptor. If DMAC descriptor pool is empty pl330_get_desc() allocates
new descriptor on shared pool using add_desc() and then get newly
allocated descriptor using pluck_desc(). At the same time thread B calls
pluck_desc() and take newly allocated descriptor. In that case descriptor
allocation for thread A will fail.

Using on-stack pool for new descriptor allow avoid the issue described.
The patch modify pl330_get_desc() to use on-stack pool for allocation
new descriptors.

Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-20 11:46:45 +05:30
Hiroyuki Yokoyama 847449f23d dmaengine: rcar-dmac: use TCRB instead of TCR for residue
SYS/RT/Audio DMAC includes independent data buffers for reading
and writing. Therefore, the read transfer counter and write transfer
counter have different values.
TCR indicates read counter, and TCRB indicates write counter.
The relationship is like below.

        TCR       TCRB
[SOURCE] -> [DMAC] -> [SINK]

In the MEM_TO_DEV direction, what really matters is how much data has
been written to the device. If the DMA is interrupted between read and
write, then, the data doesn't end up in the destination, so shouldn't
be counted. TCRB is thus the register we should use in this cases.

In the DEV_TO_MEM direction, the situation is more complex. Both the
read and write side are important. What matters from a data consumer
point of view is how much data has been written to memory.
On the other hand, if the transfer is interrupted between read and
write, we'll end up losing data. It can also be important to report.

In the MEM_TO_MEM direction, what matters is of course how much data
has been written to memory from data consumer point of view.
Here, because read and write have independent data buffers, it will
take a while for TCR and TCRB to become equal. Thus we should check
TCRB in this case, too.

Thus, all cases we should check TCRB instead of TCR.

Without this patch, Sound Capture has noise after PluseAudio support
(= 07b7acb51d ("ASoC: rsnd: update pointer more accurate")), because
the recorder will use wrong residue counter which indicates transferred
from sound device, but in reality the data was not yet put to memory
and recorder will record it.

Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
[Kuninori: added detail information in log]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-20 11:43:32 +05:30
Stefan Brüns 12e0177055 dmaengine: sun6i: Add support for Allwinner A64 and compatibles
The A64 SoC has the same dma engine as the H3 (sun8i), with a
reduced amount of physical channels. To allow future reuse of the
compatible, leave the channel count etc. in the config data blank
and retrieve it from the devicetree.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:31:36 +05:30
Stefan Brüns 500fa9e76b dmaengine: sun6i: Move number of pchans/vchans/request to device struct
Preparatory patch: If the same compatible is used for different SoCs which
have a common register layout, but different number of channels, the
channel count can no longer be stored in the config. Store it in the
device structure instead.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:31:24 +05:30
Stefan Brüns d5f6d8cf31 dmaengine: sun6i: Enable additional burst lengths/widths on H3
The H3 supports bursts lengths of 1, 4, 8 and 16 transfers, each with
a width of 1, 2, 4 or 8 bytes.

The register value for the the width is log2-encoded, change the
conversion function to provide the correct value for width == 8.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:31:24 +05:30
Stefan Brüns 88d8622c00 dmaengine: sun6i: Restructure code to allow extension for new SoCs
The current code mixes three distinct operations when transforming
the slave config to register settings:

  1. special handling of DMA_SLAVE_BUSWIDTH_UNDEFINED, maxburst == 0
  2. range checking
  3. conversion of raw to register values

As the range checks depend on the specific SoC, move these out of the
conversion to distinct operations.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:31:24 +05:30
Stefan Brüns 5a6a6202fa dmaengine: sun6i: Correct burst length field offsets for H3
For the H3, the burst lengths field offsets in the channel configuration
register differs from earlier SoC generations.

Using the A31 register macros actually configured the H3 controller
do to bursts of length 1 always, which although working leads to higher
bus utilisation.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:31:24 +05:30
Stefan Brüns 50b1249754 dmaengine: sun6i: Correct setting of clock autogating register for A83T/H3
The H83T uses a compatible string different from the A23, but requires
the same clock autogating register setting.

The H3 also requires setting the clock autogating register, but has
the register at a different offset.

Add three suitable callbacks for the existing controller generations
and set it in the controller config structure.

Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:31:24 +05:30
Ed Blake 56d355e6f5 dmaengine: img-mdc: Add runtime PM
Add runtime PM support to disable the clock when the h/w is not in use.
The existing clock_prepare_enable is removed from probe() as the clock
is no longer permanently enabled.

Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:15:39 +05:30
Ed Blake fd9f22ae15 dmaengine: img-mdc: Add suspend / resume handling
Add suspend / resume handling using suspend_late and resume_early, and
check that all channels are idle before suspending.

DMA drivers should use suspend_late / resume_early to ensure that all
DMA client devices are suspended before the DMA device itself, and that
client devices are resumed after the DMA device. This avoids suspending
the DMA device while transactions are still active.

It is the responsibility of client drivers to terminate all DMA
transactions in their suspend handlers, so there should be no active
transactions by the time suspend_late is called.

There's no need to save and restore registers for MDC during suspend /
resume, as all transactions will be terminated as a result of the
suspend, and all required registers are programmed anyway at the start
of any new transactions following resume.

Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-16 12:15:30 +05:30
Geert Uytterhoeven f47a4133ea dmaengine: nbpfaxi: Use of_device_get_match_data() helper
Use the of_device_get_match_data() helper instead of open coding.
Note that when used with DT, there's always a valid match.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-12 22:20:51 +05:30
Peter Ujfalusi 05ec62a106 dmaengine: omap-dma: Implement protection for invalid max_burst
the device's max_burst to 16777215 (EN is 24bit unsigned value) so
clients can take this into consideration when setting up the transfer.

During slave transfer preparation check if the requested maxburst is valid.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-12 22:13:48 +05:30
Peter Ujfalusi ea09ea51dd dmaengine: edma: Implement protection for invalid max_burst
the device's max_burst to 32767 (CIDX is 16bit signed value) so clients
can take this into consideration when setting up the transfer.

During slave transfer preparation check if the requested maxburst is valid.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-12 22:13:06 +05:30
Colin Ian King f2fd4d9f32 dmaengine: stm32: remove redundant initialization of hwdesc
hwdesc is being initialized to desc->hwdesc but this is never read
as hwdesc is overwritten in a for-loop.  Remove the redundant
initialization and move the declaration of hwdesc into the for-loop.

Cleans up clang warning:
Value stored to 'hwdesc' during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-12 19:34:41 +05:30
Arnd Bergmann ea62e2ccbb dmaengine: stm32_mdma: add CONFIG_OF dependency
Without CONFIG_OF we get a build warning:

warning: (STM32_MDMA) selects DMA_OF which has unmet direct dependencies (DMADEVICES && OF)

This adds a dependency on CONFIG_OF. Since this means
we no longer need to select 'DMA_OF', I'm dropping that line
as well.

Fixes: a4ffb13c89 ("dmaengine: Add STM32 MDMA driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-12 19:33:55 +05:30
Vinod Koul 38502f232e dmaengine: stm32: use %p format specfier for pointer
Pointer print was using explict cast and printing as %x which causes below
warn on some arch's so print using %p format specfier.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-08 20:28:15 +05:30
Dan Carpenter 4219ff33b2 dmaengine: stm32-dmamux: Fix a NULL vs IS_ERR() check in probe
devm_ioremap_resource() doesn't return NULL, it returns error pointers.

Fixes: df7e762db5 ("dmaengine: Add STM32 DMAMUX driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-08 16:17:39 +05:30
Pierre-Yves MORDRET a4ffb13c89 dmaengine: Add STM32 MDMA driver
This patch adds the driver for the STM32 MDMA controller.

Master Direct memory access (MDMA) is used in order to provide high-speed
data transfer between memory and memory or between peripherals and memory.

MDMA controller provides a master AXI interface for main memory and
peripheral registers access (system access port) and a master AHB
interface only for Cortex-M7 TCM memory access (TCM access port).

MDMA works in conjunction with the standard DMA controllers (DMA1 or DMA2).
It offers up to 64 channels, each dedicated to managing memory access
requests from one of the DMA stream memory buffer or other peripherals
(w/ integrated FIFO).

Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-10-08 14:45:34 +05:30
Sylvain Lesne edf10919e5 dmaengine: altera: fix spinlock usage
Since this lock is acquired in both process and IRQ context, failing to
to disable IRQs when trying to acquire the lock in process context can
lead to deadlocks.

Signed-off-by: Sylvain Lesne <lesne@alse-fr.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-28 13:11:46 +05:30
Sylvain Lesne d9ec46416d dmaengine: altera: fix response FIFO emptying
Commit 6084fc2ec4 ("dmaengine: altera: Use macros instead of structs
to describe the registers") introduced a minus sign before a register
offset.

This leads to soft-locks of the DMA controller, since reading the last
status byte is required to pop the response from the FIFO. Failing to
do so will lead to a full FIFO, which means that the DMA controller
will stop processing descriptors.

Signed-off-by: Sylvain Lesne <lesne@alse-fr.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-28 13:11:46 +05:30
Russell King 73d2a3cef4 dmaengine: sa11x0: add DMA filters
Add DMA filters for the sa11x0 DMA channels.  This will allow us to
migrate away from directly using the DMA filter function in drivers.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-27 16:11:51 +05:30
Pierre-Yves MORDRET df7e762db5 dmaengine: Add STM32 DMAMUX driver
This patch implements the STM32 DMAMUX driver.

The DMAMUX request multiplexer allows routing a DMA request line between
the peripherals and the DMA controllers of the product. The routing
function is ensured by a programmable multi-channel DMA request line
multiplexer. Each channel selects a unique DMA request line,
unconditionally or synchronously with events from its DMAMUX
synchronization inputs. The DMAMUX may also be used as a DMA request
generator from programmable events on its input trigger signals

Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-27 16:01:35 +05:30
Sricharan R 6b4faeac05 dmaengine: qcom-bam: Process multiple pending descriptors
The bam dmaengine has a circular FIFO to which we
add hw descriptors that describes the transaction.
The FIFO has space for about 4096 hw descriptors.

Currently we add one descriptor and wait for it to
complete with interrupt and then add the next pending
descriptor. In this way, the FIFO is underutilized
since only one descriptor is processed at a time, although
there is space in FIFO for the BAM to process more.

Instead keep adding descriptors to FIFO till its full,
that allows BAM to continue to work on the next descriptor
immediately after signalling completion interrupt for the
previous descriptor.

Also when the client has not set the DMA_PREP_INTERRUPT for
a descriptor, then do not configure BAM to trigger a interrupt
upon completion of that descriptor. This way we get a interrupt
only for the descriptor for which DMA_PREP_INTERRUPT was
requested and there signal completion of all the previous completed
descriptors. So we still do callbacks for all requested descriptors,
but just that the number of interrupts are reduced.

CURRENT:

            ------      -------   ---------------
            |DES 0|     |DESC 1|  |DESC 2 + INT |
            ------      -------   ---------------
               |           |            |
               |           |            |
INTERRUPT:   (INT)       (INT)	      (INT)
CALLBACK:     (CB)        (CB)         (CB)

		MTD_SPEEDTEST READ PAGE: 3560 KiB/s
		MTD_SPEEDTEST WRITE PAGE: 2664 KiB/s
		IOZONE READ: 2456 KB/s
		IOZONE WRITE: 1230 KB/s

	bam dma interrupts (after tests): 96508

CHANGE:

        ------  -------    -------------
        |DES 0| |DESC 1   |DESC 2 + INT |
        ------  -------   --------------
				|
				|
          		      (INT)
			      (CB for 0, 1, 2)

		MTD_SPEEDTEST READ PAGE: 3860 KiB/s
		MTD_SPEEDTEST WRITE PAGE: 2837 KiB/s
		IOZONE READ: 2677 KB/s
		IOZONE WRITE: 1308 KB/s

	bam dma interrupts (after tests): 58806

Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-25 11:47:26 +05:30
Peter Ujfalusi 2ccb4837c9 dmaengine: ti-dma-crossbar: Fix possible race condition with dma_inuse
When looking for unused xbar_out lane we should also protect the set_bit()
call with the same mutex to protect against concurrent threads picking the
same ID.

Fixes: ec9bfa1e1a ("dmaengine: ti-dma-crossbar: dra7: Use bitops instead of idr")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-21 23:03:42 +05:30
Corentin Labbe 8f3b00347b dmaengine: sun6i: use of_device_get_match_data
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() return NULL.

Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-21 22:53:38 +05:30
Peter Ujfalusi 87a2f622cc dmaengine: edma: Align the memcpy acnt array size with the transfer
Memory to Memory transfers does not have any special alignment needs
regarding to acnt array size, but if one of the areas are in memory mapped
regions (like PCIe memory), we need to make sure that the acnt array size
is aligned with the mem copy parameters.

Before "dmaengine: edma: Optimize memcpy operation" change the memcpy was set
up in a different way: acnt == number of bytes in a word based on
__ffs((src | dest | len), bcnt and ccnt for looping the necessary number of
words to comlete the trasnfer.

Instead of reverting the commit we can fix it to make sure that the ACNT size
is aligned to the traswnfer.

Fixes: df6694f803 (dmaengine: edma: Optimize memcpy operation)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-21 22:51:07 +05:30
Nicolin Chen f9d4a398f1 dmaengine: imx-sdma: Correct src_addr_widths and directions
The driver already supports DMA_DEV_TO_DEV in sdma_config(),
DMA_SLAVE_BUSWIDTH_2_BYTES and DMA_SLAVE_BUSWIDTH_1_BYTE in
sdma_prep_slave_sg(). So this patch adds them to the lists.

Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-21 22:45:42 +05:30
Lars-Peter Clausen f3ae7d9155 dmaengine: xilinx_dma: Move enum xdma_ip_type to driver file
The enum xdma_ip_type is only used inside the Xilinx DMA driver and not
exported to any consumers (nor should it be). So move it from the global
header to driver file itself.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-17 18:59:54 +05:30
Lars-Peter Clausen 008913dbeb dmaengine: axi-dmac: Fix software cyclic mode
When running in software cyclic mode the driver currently does not go back
to the first segment once the last segment has been reached. Effectively
making the transfer non-cyclic.

Fix this by going back to the first segment once the last segment has been
reached for cyclic transfers.

Special care need to be taken to avoid a segment from being submitted
multiple times concurrently, which could happen for transfers with a number
of segments that is smaller than the DMA controller's internal queue.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-17 18:58:18 +05:30
Lars-Peter Clausen 63ab76dbbd dmaengine: axi-dmac: Only use hardware cyclic mode for single segment transfers
In hardware cyclic mode the submitted segment is repeated. This means
hardware cyclic mode can only be used if the transfer has a single segment.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-17 18:58:18 +05:30
Linus Torvalds cd7b34fe1c dmaengine updates for 4.14-rc1
- Removal of DMA_SG support as we have no users for this feature
  - New driver for Altera / Intel mSGDMA IP core
  - Support for memset in dmatest and qcom_hidma driver
  - Update for non cyclic mode in k3dma, bunch of update in bam_dma, bcm sba-raid
  - Constify device ids across drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZsXteAAoJEHwUBw8lI4NHPwcP/iihF1n7jOQVtUm3zxPvUV+n
 GzU7+rqAEDLKBaIttK28LIjgvg0AC/4aiEsosfCzTjpkzMHteRw00YyplwF7/wdM
 O0owKOIub4PriDiL6d/SWFnhcWwv0/KLbyKscQcOwwvkksG/mwMn1VfW7alCrz1w
 81TOQaW9SxLxL7guJU0aQHljkudT53l8Dgsp55iC9Ccz515Iuu7dQm3DnSG3sYjJ
 Ct4u4MWWzDmmKKpbDoYe/Z+fiQT0WKuGfI7QHURVnw5qLo2sDKREWGbThhRG/lZj
 YlnLQnkjWwLU5dyX1MyIWipPxe83sjf/7OwJ7XUlLjD6o+lNEuQxjmNkVAh0hNRc
 dgrXRuqPRJMW40uOvAMDHTkexxikWc5ggt5LN9dIYDOdaS4Ch5ewf19SRi9pSDap
 FZeIWY1FWwQCAU7HQMwSYyRLBjlmEmeSkElkXCd+2wu5aH2oKOMUMbUIYcqL4fjD
 qMAR7kfn6e92fDT1gR1ZKL79Cfe9zsCQA3XmecpC/HwqiE3XtfZuDY/73cXD0MeO
 SbJUCv4ldPGjrTKBHvs0wiWbxi5Mj5sXglmSaD0lEhtMsOfhPHY2BGatTzSmKKwO
 WwmKAvM8qElQZy2Eh25dvlE04yAOofoJb6Pf/AraQOLTUkMyF8wRWEpltjUuttM9
 VzQLvh8s25naKM5mOAM2
 =88SI
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-4.14-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:
 "This one features the usual updates to the drivers and one good part
  of removing DA_SG from core as it has no users.

  Summary:

   - Remove DMA_SG support as we have no users for this feature
   - New driver for Altera / Intel mSGDMA IP core
   - Support for memset in dmatest and qcom_hidma driver
   - Update for non cyclic mode in k3dma, bunch of update in bam_dma,
     bcm sba-raid
   - Constify device ids across drivers"

* tag 'dmaengine-4.14-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (52 commits)
  dmaengine: sun6i: support V3s SoC variant
  dmaengine: sun6i: make gate bit in sun8i's DMA engines a common quirk
  dmaengine: rcar-dmac: document R8A77970 bindings
  dmaengine: xilinx_dma: Fix error code format specifier
  dmaengine: altera: Use macros instead of structs to describe the registers
  dmaengine: ti-dma-crossbar: Fix dra7 reserve function
  dmaengine: pl330: constify amba_id
  dmaengine: pl08x: constify amba_id
  dmaengine: bcm-sba-raid: Remove redundant SBA_REQUEST_STATE_COMPLETED
  dmaengine: bcm-sba-raid: Explicitly ACK mailbox message after sending
  dmaengine: bcm-sba-raid: Add debugfs support
  dmaengine: bcm-sba-raid: Remove redundant SBA_REQUEST_STATE_RECEIVED
  dmaengine: bcm-sba-raid: Re-factor sba_process_deferred_requests()
  dmaengine: bcm-sba-raid: Pre-ack async tx descriptor
  dmaengine: bcm-sba-raid: Peek mbox when we have no free requests
  dmaengine: bcm-sba-raid: Alloc resources before registering DMA device
  dmaengine: bcm-sba-raid: Improve sba_issue_pending() run duration
  dmaengine: bcm-sba-raid: Increase number of free sba_request
  dmaengine: bcm-sba-raid: Allow arbitrary number free sba_request
  dmaengine: bcm-sba-raid: Remove reqs_free_count from sba_device
  ...
2017-09-07 14:03:05 -07:00
Vinod Koul 41bd0314fa Merge branch 'topic/dmatest' into for-linus 2017-09-06 21:55:10 +05:30
Vinod Koul 346ea25e81 Merge branch 'topic/qcom' into for-linus 2017-09-06 21:54:48 +05:30
Vinod Koul 05890d550c Merge branch 'topic/ppc4xx' into for-linus 2017-09-06 21:54:41 +05:30
Vinod Koul 918a21eeec Merge branch 'topic/of' into for-linus 2017-09-06 21:54:31 +05:30
Vinod Koul dccafbf2d3 Merge branch 'topic/k3dma' into for-linus 2017-09-06 21:54:24 +05:30
Vinod Koul f6cc35eefe Merge branch 'topic/ioat' into for-linus 2017-09-06 21:54:16 +05:30
Vinod Koul 07e24b8559 Merge branch 'topic/bcm' into for-linus 2017-09-06 21:54:09 +05:30
Vinod Koul a431cbafcb Merge branch 'topic/altera' into for-linus 2017-09-06 21:54:01 +05:30
Icenowy Zheng a702e47eab dmaengine: sun6i: support V3s SoC variant
Allwinner V3s has a DMA engine similar to the ones from A31, but with
fewer channels and DRQs.

Add support for it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-05 09:07:20 +05:30
Icenowy Zheng 0430a7c753 dmaengine: sun6i: make gate bit in sun8i's DMA engines a common quirk
Originally we enable a special gate bit when the compatible indicates
A23/33.

But according to BSP sources and user manuals, more SoCs will need this
gate bit.

So make it a common quirk configured in the config struct.

Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-05 09:07:20 +05:30
Lars-Peter Clausen 574897dc14 dmaengine: xilinx_dma: Fix error code format specifier
'err' is a signed int and error codes are typically negative numbers, so
use '%d' instead of '%u' to format the error code in the error message.

Fixes: ba16db36b5 ("dmaengine: vdma: Add clock support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-09-05 09:03:21 +05:30
Stefan Roese 6084fc2ec4 dmaengine: altera: Use macros instead of structs to describe the registers
This patch moves from a struct declaration for the DMA controller
registers to macros with offests to the base address. This is mainly
done to remove the sparse warnings, since the function parameter of
ioread32/iowrite32 is "void __iomem *" instead of a pointer to struct
members. With this patch applied, no sparse warning is seen anymore.

Please note that the struct for the descriptors is still kept in place,
as the code largely accesses the struct members as internal variables
before the complete struct is copied into the descriptor FIFO of the
DMA controller.

Additionally this patch also removes two warnings "variable xxx set but
not used" seen when compiling with "W=1". The registers need to be read
to flush the response FIFO, but nothing needs to be done with them. So
the code is correct here and the warning is a false one.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-29 08:17:43 +05:30
Alexander Smirnov a2f6721b42 dmaengine: ti-dma-crossbar: Fix dra7 reserve function
DMA crossbar uses 'xbar->dma_inuse' variable to manage allocated routes.
Each bit represents respective DMA channel. If the channel is free, bit
is set to '0', if channel is allocated, bit should be set to '1'.

In reserve function, the bits for requested DMA channels are cleared, so
they are not really reserved, but freed and become ready for allocation.

Signed-off-by: Alexander Smirnov <asmirnov@ilbers.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 22:02:05 +05:30
Arvind Yadav b753351ec8 dmaengine: pl330: constify amba_id
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 21:11:08 +05:30
Arvind Yadav b80fa1217c dmaengine: pl08x: constify amba_id
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 21:11:08 +05:30
Anup Patel ecbf9ef15a dmaengine: bcm-sba-raid: Remove redundant SBA_REQUEST_STATE_COMPLETED
The SBA_REQUEST_STATE_COMPLETED state was added to keep track
of sba_request which got completed but cannot be freed because
underlying Async Tx descriptor was not ACKed by DMA client.

Instead of above, we can free the sba_request with non-ACKed
Async Tx descriptor and sba_alloc_request() will ensure that
it always allocates sba_request with ACKed Async Tx descriptor.
This alternate approach makes SBA_REQUEST_STATE_COMPLETED state
redundant hence this patch removes it.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 29e0f486d9 dmaengine: bcm-sba-raid: Explicitly ACK mailbox message after sending
We should explicitly ACK mailbox message because after
sending message we can know the send status via error
attribute of brcm_message.

This will also help SBA-RAID to use "txdone_ack" method
whenever mailbox controller supports it.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 8529a927e2 dmaengine: bcm-sba-raid: Add debugfs support
This patch adds debugfs support to report stats via debugfs
which in-turn will help debug hang or error situations.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel b99c238669 dmaengine: bcm-sba-raid: Remove redundant SBA_REQUEST_STATE_RECEIVED
The SBA_REQUEST_STATE_RECEIVED state is now redundant because
received sba_request are immediately freed or moved to completed
list in sba_process_received_request().

This patch removes redundant SBA_REQUEST_STATE_RECEIVED state.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel d6ffd2395a dmaengine: bcm-sba-raid: Re-factor sba_process_deferred_requests()
Currently, sba_process_deferred_requests() handles both pending
and completed sba_request which is unnecessary overhead for
sba_issue_pending() because completed sba_request handling is
not required in sba_issue_pending().

This patch breaks sba_process_deferred_requests() into two parts
sba_process_received_request() and _sba_process_pending_requests().

The sba_issue_pending() will only process pending sba_request
by calling _sba_process_pending_requests(). This will improve
sba_issue_pending().

The sba_receive_message() will only process received sba_request
by calling sba_process_received_request() for each received
sba_request. The sba_process_received_request() will also call
_sba_process_pending_requests() after handling received sba_request
because we might have pending sba_request not submitted by previous
call to sba_issue_pending().

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel fd8eb5395f dmaengine: bcm-sba-raid: Pre-ack async tx descriptor
We should pre-ack async tx descriptor at time of
allocating sba_request (just like other RAID drivers).

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 6df8f913d2 dmaengine: bcm-sba-raid: Peek mbox when we have no free requests
When setting up RAID array on several NVMe disks we observed that
sba_alloc_request() start failing (due to no free requests left)
and RAID array setup becomes very slow.

To improve performance, we do mbox channel peek when we have
no free requests. This improves performance of RAID array setup
because mbox requests that were completed but not processed by
mbox completion worker will be processed immediately by mbox
channel peek.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel eb67744b9a dmaengine: bcm-sba-raid: Alloc resources before registering DMA device
We should allocate DMA channel resources before registering the
DMA device in sba_probe() because we can get DMA request soon
after registering the DMA device. If DMA channel resources are
not allocated before first DMA request then SBA-RAID driver will
crash.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel f83385142c dmaengine: bcm-sba-raid: Improve sba_issue_pending() run duration
The pending sba_request list can become very long in real-life usage
(e.g. setting up RAID array) which can cause sba_issue_pending() to
run for long duration.

This patch adds common sba_process_deferred_requests() to process
few completed and pending requests so that it finishes in short
duration. We use this common sba_process_deferred_requests() in
both sba_issue_pending() and sba_receive_message().

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 5346aafcef dmaengine: bcm-sba-raid: Increase number of free sba_request
Currently, we have only 1024 free sba_request created
by sba_prealloc_channel_resources(). This is too low
and the prep_xxx() callbacks start failing more often
at time of RAID array setup over NVMe disks.

This patch sets number of free sba_request created by
sba_prealloc_channel_resources() to be:
<number_of_mailbox_channels> x 8192

Due to above, we will have sufficient number of free
sba_request and prep_xxx() callbacks failing is very
unlikely.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 5655e00f5c dmaengine: bcm-sba-raid: Allow arbitrary number free sba_request
Currently, we cannot have any arbitrary number of free sba_request
because sba_prealloc_channel_resources() allocates an array of
sba_request using devm_kcalloc() and kcalloc() cannot provide
memory beyond certain size.

This patch removes "reqs" (sba_request array) from sba_device
and makes "cmds" as variable array (instead of pointer) in
sba_request. This helps sba_prealloc_channel_resources() to
allocate sba_request and associated SBA command in one allocation
which in-turn allows arbitrary number of free sba_request.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel abfa251afe dmaengine: bcm-sba-raid: Remove reqs_free_count from sba_device
The reqs_free_count member of sba_device is not used anywhere
hence no point in tracking number of free sba_request.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel e7ae72aa65 dmaengine: bcm-sba-raid: Remove redundant resp_dma from sba_request
Both resp and resp_dma are redundant in sba_request because
resp is unused and resp_dma carries same information present
in tx.phys of sba_request. This patch removes both resp and
resp_dma from sba_request.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 10f1a33080 dmaengine: bcm-sba-raid: Remove redundant next_count from sba_request
The next_count in sba_request is redundant because same information
is captured by next_pending_count. This patch removes next_count
from sba_request.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel 57a2850859 dmaengine: bcm-sba-raid: Common flags for sba_request state and fence
This patch merges sba_request state and fence into common
sba_request flags. The sba_request flags not only saves
memory but it can also be extended in-future without adding
new members.

We also make each sba_request state as separate bit in
sba_request flags to help debugging situations where a
sba_request is accidently in two states.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel e4274cfa42 dmaengine: bcm-sba-raid: Reduce locking context in sba_alloc_request()
We don't require to hold "sba->reqs_lock" for long-time
in sba_alloc_request() because lock protection is not
required when initializing members of "struct sba_request".

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Anup Patel e897091ab9 dmaengine: bcm-sba-raid: Minor improvments in comments
This patch does following improvments to comments:
1. Make section comments consistent across the driver by
avoiding " SBA " in some of the comments
2. Add/update few more section comments

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:44:24 +05:30
Abhishek Sahu 749d0d4bbb dmaengine: qcom: bam_dma: add command descriptor flag
If DMA_PREP_CMD flag is passed in prep_slave_sg then peripheral
driver has passed the data is in BAM command descriptor format
and BAM driver should set CMD bit for each of the HW descriptors.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 16:40:18 +05:30
Vinod Koul 3eeb515636 dmaengine: remove BUG_ON while registering devices
DMAengine core has BUG_ON to check for mandatory operations and ones based
on capabilities, but they use BUG_ON, so remove and move to error returns
and logging the errors gracefully

Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-28 09:39:46 +05:30
Kuninori Morimoto 5e857047ba dmaengine: rcar-dmac: initialize all data before registering IRQ handler
Anton Volkov noticed that engine->dev is NULL before
of_dma_controller_register() in probe.
Thus there might be a NULL pointer dereference in
rcar_dmac_chan_start_xfer while accessing chan->chan.device->dev which
is equal to (&dmac->engine)->dev.
On same reason, same and similar things will happen if we didn't
initialize all necessary data before calling register irq function.
To be more safety code, this patch initialize all necessary data
before calling register irq function.

Reported-by: Anton Volkov <avolkov@ispras.ru>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-25 12:27:07 +05:30
Antonio Borneo aa1841b983 dmaengine: k3dma: remove useless ON_WARN_ONCE()
Commit 36387a2b1f ("k3dma: Fix
memory handling in preparation for cyclic mode") adds few
calls to ON_WARN_ONCE() to track the use of ds_run/ds_done.

After the two fixes:
- dmaengine: k3dma: fix non-cyclic mode
- dmaengine: k3dma: fix re-free of the same descriptor
the behaviour of ds_run/ds_done is properly fixed.
The remaining ON_WARN_ONCE() are never triggered and can be
removed.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-25 12:15:40 +05:30
Antonio Borneo 132b473cd5 dmaengine: k3dma: fix double free of descriptor
Commit 36387a2b1f ("k3dma: Fix
memory handling in preparation for cyclic mode") adds code
to free the descriptor in ds_done.

In cyclic mode, ds_done is never used and it's always NULL,
so the added code is not executed.

In non-cyclic mode, ds_done is used as a flag: when not NULL
it signals that the descriptor has been consumed. No need to
free it because it would be free by vchan_complete().

The fix takes back the code changed by the commit above:
- remove the free on the descriptor;
- initialize ds_done to NULL for the next run.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-25 12:15:40 +05:30
Antonio Borneo 626c4e85a1 dmaengine: k3dma: fix non-cyclic mode
Commit 36387a2b1f ("k3dma: Fix
memory handling in preparation for cyclic mode") broke the
logic around ds_run/ds_done in case of non-cyclic DMA.

This went unnoticed as the only user of k3dma was the i2s
audio driver but, with a patch set to enable dma on SPI, the
issue popped out.

The fix re-applies the initialization to ds_run/ds_done in
k3_dma_start_txd() that were removed by the commit above.

Also, one of the calls to k3_dma_start_txd() is triggered by
(ds_done != NULL), so remove the noisy and useless call to
WARN_ON_ONCE().

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-25 12:15:40 +05:30
Ujjal Singh 268e2519f5 dmaengine: ioatdma: Add intr_coalesce sysfs entry
We observed performance increase with DMA copy from memory
to MMIO by changing the interrupt coalescing value to 0.
The previous set value was projected on the C5xxx Xeon
platform and no longer holds true. Removing hard coded
value and providing a tune-able in sysfs in order to allow
user to tune this on a per channel basis. By default this
value will be set to 0.
Example of sysfs variable importing for interrupt coalescing
value from command line:
echo 5> /sys/devices/pci0000:00/0000:00:04.0/dma/dma0chan0/
quickdata/intr_coalesce

Reported-by: Nithin Sujir <nsujir@tintri.com>
Signed-off-by: Ujjal Singh <ujjal.singh@intel.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-23 21:32:21 +05:30
Vinod Koul 99380edf9e dmaengine: xgene-dma: remove unused xgene_dma_invalidate_buffer
Commit c678fa66341c: ("dmaengine: remove DMA_SG as it is dead code in
kernel") removes DMA_SG from dmaengine subsystem but missed removing unused
xgene_dma_invalidate_buffer function, so remove it

drivers/dma/xgene-dma.c:394:13: warning: ‘xgene_dma_invalidate_buffer’ defined but not used [-Wunused-function]
 static void xgene_dma_invalidate_buffer(__le64 *ext8)

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-22 22:13:44 +05:30
Vinod Koul 491bea00a1 dmaengine: altera: remove DMA_SG
Commit c678fa66341c: ("dmaengine: remove DMA_SG as it is dead code in
kernel") removes DMA_SG from dmaengine subsystem but missed the newly added
driver, so remove it from here as well

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-22 22:03:43 +05:30
Dave Jiang c678fa6634 dmaengine: remove DMA_SG as it is dead code in kernel
There are no in kernel consumers for DMA_SG op. Removing operation,
dead code, and test code in dmatest.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-22 09:22:11 +05:30
Arvind Yadav 87c56dcba4 dmaengine: at_xdmac: Handle return value of clk_prepare_enable.
clk_prepare_enable() can fail here and we must check its return value.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-21 22:20:44 +05:30
Arvind Yadav 1edc85dc56 dmaengine: at_xdmac: Fix compilation warning.
Replace '%d' by '%zu' to fix the compilation warning:-
   "format ‘%d’ expects argument of type ‘int’,but argument has type ‘size_t’ [-Wformat=]"

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-21 22:20:43 +05:30
Bhumika Goyal e43341ca85 dmaengine: ste_dma40: make stedma40_chan_cfg const
Make these const as they are only used during a copy operation.
Done using Coccinelle.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-21 21:56:12 +05:30
Anton Vasilyev a63efead7f dmaengine: qcom_hidma: avoid freeing an uninitialized pointer
If device_node np doesn't contain child or first child doesn't have
property "reg" then hidma_mgmt_of_populate_channels() perfoms
deallocation on uninitialized local variable res.

The patch adds res initialization by NULL.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-21 21:51:00 +05:30
Sergei Shtylyov 7f5770678b dmaengine: tegra210-adma: fix of_irq_get() error check
of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would then
call request_irq(0, ...) in tegra_adma_alloc_chan_resources() and never get
valid channel interrupt.

Check for 'tdc->irq <= 0' instead and return -ENXIO from the driver's probe
iff of_irq_get() returned 0.

Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-08-09 11:39:16 +05:30
Greg Kroah-Hartman 13efe1a053 dmaengine: ppc4xx: remove DRIVER_ATTR() usage
It's better to be explicit and use the DRIVER_ATTR_RW() and
DRIVER_ATTR_RO() macros when defining a driver's sysfs file.

Bonus is this fixes up a checkpatch.pl warning.

This is part of a series to drop DRIVER_ATTR() from the tree entirely.

Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-21 12:02:49 +05:30
Vinod Koul dd2bceb0a8 dmaengine: bcm-scm-raid: statify functions
This driver builds with warnings which can be fixed by making these
functions static.

  CC [M]  drivers/dma/bcm-sba-raid.o
drivers/dma/bcm-sba-raid.c:786:1: warning: no previous prototype for ‘sba_prep_dma_xor_req’ [-Wmissing-prototypes]
 sba_prep_dma_xor_req(struct sba_device *sba,
 ^
drivers/dma/bcm-sba-raid.c:995:1: warning: no previous prototype for ‘sba_prep_dma_pq_req’ [-Wmissing-prototypes]
 sba_prep_dma_pq_req(struct sba_device *sba, dma_addr_t off,
 ^
drivers/dma/bcm-sba-raid.c:1247:1: warning: no previous prototype for ‘sba_prep_dma_pq_single_req’ [-Wmissing-prototypes]
 sba_prep_dma_pq_single_req(struct sba_device *sba, dma_addr_t off,
 ^

Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-19 10:03:24 +05:30
Sinan Kaya 8e7341750b dmaengine: qcom_hidma: correct channel QOS register offset
A regression was found while testing QOS with different channels.
The QOS register offset is 0x700 rather than 0x300.

Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-19 09:38:55 +05:30
Sinan Kaya 0217cccdbf dmaengine: qcom_hidma: correct overriding message
A false overriding information is being presented during boot
under this scenario.

1. First object checks for kernel command line value against zero.
2. It doesn't find it, it sets the command line variable to the
value coming from ACPI/DT.
3. Second object is being probed.
4. Second object sees that the value of kernel command line
override is non-zero, it prints an overriding message even though
value matches ACPI/DT value.

hidma-mgmt QCOM8060:03: overriding max-write-burst-bytes: 1024

Add an additional check to verify that kernel command line value
is different from the ACPI/DT value.

Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-19 09:38:55 +05:30
Sinan Kaya 5e2db086be dmaengine: qcom_hidma: introduce memset support
HIDMA HW supports memset operation in addition to memcpy.
Since the memset API is present on the kernel now, bring the
memset feature into life.

The descriptor format is the same for both memcpy and memset.
Type of the descriptor is 4 when memset is requested.
The lowest 8 bits of the source DMA argument is used as a
fill pattern.

Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-19 09:33:21 +05:30
Rob Herring c6c93048ba dmaengine: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-19 09:30:44 +05:30
Stefan Roese a85c6f1b29 dmaengine: Add driver for Altera / Intel mSGDMA IP core
This driver adds support for the Altera / Intel modular Scatter-Gather
Direct Memory Access (mSGDMA) intellectual property (IP) to the Linux
DMAengine subsystem. Currently it supports the following op modes:

- DMA_MEMCPY
- DMA_SG
- DMA_SLAVE

This implementation has been tested on an Altera Cyclone FPGA connected
via PCIe, both on an ARM and an x86 platform.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-18 22:04:54 +05:30
Sinan Kaya 61b5f54d8c dmaengine: dmatest: add support for memset test
Introducing memset test into dmatest. This change allows us to test
memset capable HW using the dmatest test procedure. The new dmatest
value for memset is 2 and it is not the default value.

Memset support patch shares the same code path as the other dmatest
code to reuse as much as we can.

The first value inside the source buffer is used as a pattern
to fill in the destination buffer space.

Prior to running the test, source/destination buffers are initialized
in the current code.

"The remaining bits are the inverse of a counter which increments by
 one for each byte address."

Memset test will fill in the upper bits of pattern with the inverse of
fixed counter value 1 as opposed to an incrementing value in a loop.

An example run is as follows:

echo dma0chan0 > /sys/module/dmatest/parameters/channel
echo 2 >  /sys/module/dmatest/parameters/dmatest
echo 2000 >  /sys/module/dmatest/parameters/timeout
echo 10 >  /sys/module/dmatest/parameters/iterations
echo 1 >  /sys/module/dmatest/parameters/run

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-18 21:55:34 +05:30
Arvind Yadav 01fa2fae5a dmaengine: ioat: constify pci_device_id.
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
  12582	   3056	     16	  15654	   3d26	drivers/dma/ioat/init.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
  14773	    865	     16	  15654	   3d26	drivers/dma/ioat/init.o

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
2017-07-18 21:32:14 +05:30
Linus Torvalds 2ceedf97ae dmaengine updates for 4.13-rc1
- removal of AVR32 support in dw driver as AVR32 is gone
  - new driver for Broadcom stream buffer accelerator (SBA) RAID driver
  - add support for Faraday Technology FTDMAC020 in amba-pl08x driver
  - IOMMU support in pl330 driver
  - updates to bunch of drivers
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZYG73AAoJEHwUBw8lI4NH+DoP/1f0TsYrQFCjNqa4nybjU1Sd
 bbqnpouuJscwt8Qk2LGuSimi0QG91gQOLvrmueFbXtEg86nPOfa0RnWGNF4qwYFK
 oliDlXF2PnV65J5kl7CvqXCj6bFiXCULVdO9JD2HFoFB1+lzXN9JQqOG5ne29BQ6
 g3HNRlUTXNzQXWisgbAOLxuuvyfv68Zo3wCLYLkd4vC/C4zmxM+KXUG8+s0hS7t3
 AOUpYW6F/C+y1Ax+SiACm0QGNZ4rc6/+ZUIIXUO5CfTYGjv6QUdzxiLHtc4br25l
 2CoN9IP4V/OxHaW9T1jA61TeAAFr63oXYfDMBBzclzVryZRAIU72ups31uRQXpFz
 99zUQ0OsdOCvy0oPInhNd8u+cpyh/4e2RDgSZ9rxw3xVaKFh8lsw5OtcCBQzCMeI
 xgFCUBHsLjEi4uafJcl6n2T7+Y4Y0KgOmxPHZo3tpq/2a5M6tVy8k68m3afCQylF
 1SOxzVZdDRUutPpviQWop6RgP0EcVuzaUJ0vO4nat4j77vuimaPqdk+oLV46XP2d
 5I52kcvbVI4BbJavTjVs3FRdcez0pW37iOw+5MOxHE3dnBp4X/3btFzBY4aOsdg0
 wVut3B+9U4WHDBF2ConBxxMvGqMYmcssOQ096GdC6oBHHS7x6n7tEVPiZ5iUacn5
 LB8k9AZtpBC7nUWPH7FS
 =srPZ
 -----END PGP SIGNATURE-----

Merge tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma

Pull dmaengine updates from Vinod Koul:

 - removal of AVR32 support in dw driver as AVR32 is gone

 - new driver for Broadcom stream buffer accelerator (SBA) RAID driver

 - add support for Faraday Technology FTDMAC020 in amba-pl08x driver

 - IOMMU support in pl330 driver

 - updates to bunch of drivers

* tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
  dmaengine: qcom_hidma: correct API violation for submit
  dmaengine: zynqmp_dma: Remove max len check in zynqmp_dma_prep_memcpy
  dmaengine: tegra-apb: Really fix runtime-pm usage
  dmaengine: fsl_raid: make of_device_ids const.
  dmaengine: qcom_hidma: allow ACPI/DT parameters to be overridden
  dmaengine: fsldma: set BWC, DAHTS and SAHTS values correctly
  dmaengine: Kconfig: Simplify the help text for MXS_DMA
  dmaengine: pl330: Delete unused functions
  dmaengine: Replace WARN_TAINT_ONCE() with pr_warn_once()
  dmaengine: Kconfig: Extend the dependency for MXS_DMA
  dmaengine: mxs: Use %zu for printing a size_t variable
  dmaengine: ste_dma40: Cleanup scatterlist layering violations
  dmaengine: imx-dma: cleanup scatterlist layering violations
  dmaengine: use proper name for the R-Car SoC
  dmaengine: imx-sdma: Fix compilation warning.
  dmaengine: imx-sdma: Handle return value of clk_prepare_enable
  dmaengine: pl330: Add IOMMU support to slave tranfers
  dmaengine: DW DMAC: Handle return value of clk_prepare_enable
  dmaengine: pl08x: use GENMASK() to create bitmasks
  dmaengine: pl08x: Add support for Faraday Technology FTDMAC020
  ...
2017-07-08 12:36:50 -07:00
Linus Torvalds f72e24a124 This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
 code related to dma-mapping, and will further consolidate arch code
 into common helpers.
 
 This pull request contains:
 
  - removal of the DMA_ERROR_CODE macro, replacing it with calls
    to ->mapping_error so that the dma_map_ops instances are
    more self contained and can be shared across architectures (me)
  - removal of the ->set_dma_mask method, which duplicates the
    ->dma_capable one in terms of functionality, but requires more
    duplicate code.
  - various updates for the coherent dma pool and related arm code
    (Vladimir)
  - various smaller cleanups (me)
 -----BEGIN PGP SIGNATURE-----
 
 iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlldmw0LHGhjaEBsc3Qu
 ZGUACgkQD55TZVIEUYOiKA/+Ln1mFLSf3nfTzIHa24Bbk8ZTGr0B8TD4Vmyyt8iG
 oO3AeaTLn3d6ugbH/uih/tPz8PuyXsdiTC1rI/ejDMiwMTSjW6phSiIHGcStSR9X
 VFNhmMFacp7QpUpvxceV0XZYKDViAoQgHeGdp3l+K5h/v4AYePV/v/5RjQPaEyOh
 YLbCzETO+24mRWdJxdAqtTW4ovYhzj6XsiJ+pAjlV0+SWU6m5L5E+VAPNi1vqv1H
 1O2KeCFvVYEpcnfL3qnkw2timcjmfCfeFAd9mCUAc8mSRBfs3QgDTKw3XdHdtRml
 LU2WuA5cpMrOdBO4mVra2plo8E2szvpB1OZZXoKKdCpK3VGwVpVHcTvClK2Ks/3B
 GDLieroEQNu2ZIUIdWXf/g2x6le3BcC9MmpkAhnGPqCZ7skaIBO5Cjpxm0zTJAPl
 PPY3CMBBEktAvys6DcudOYGixNjKUuAm5lnfpcfTEklFdG0AjhdK/jZOplAFA6w4
 LCiy0rGHM8ZbVAaFxbYoFCqgcjnv6EjSiqkJxVI4fu/Q7v9YXfdPnEmE0PJwCVo5
 +i7aCLgrYshTdHr/F3e5EuofHN3TDHwXNJKGh/x97t+6tt326QMvDKX059Kxst7R
 rFukGbrYvG8Y7yXwrSDbusl443ta0Ht7T1oL4YUoJTZp0nScAyEluDTmrH1JVCsT
 R4o=
 =0Fso
 -----END PGP SIGNATURE-----

Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping

Pull dma-mapping infrastructure from Christoph Hellwig:
 "This is the first pull request for the new dma-mapping subsystem

  In this new subsystem we'll try to properly maintain all the generic
  code related to dma-mapping, and will further consolidate arch code
  into common helpers.

  This pull request contains:

   - removal of the DMA_ERROR_CODE macro, replacing it with calls to
     ->mapping_error so that the dma_map_ops instances are more self
     contained and can be shared across architectures (me)

   - removal of the ->set_dma_mask method, which duplicates the
     ->dma_capable one in terms of functionality, but requires more
     duplicate code.

   - various updates for the coherent dma pool and related arm code
     (Vladimir)

   - various smaller cleanups (me)"

* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
  ARM: dma-mapping: Remove traces of NOMMU code
  ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
  ARM: NOMMU: Introduce dma operations for noMMU
  drivers: dma-mapping: allow dma_common_mmap() for NOMMU
  drivers: dma-coherent: Introduce default DMA pool
  drivers: dma-coherent: Account dma_pfn_offset when used with device tree
  dma: Take into account dma_pfn_offset
  dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
  dma-mapping: remove dmam_free_noncoherent
  crypto: qat - avoid an uninitialized variable warning
  au1100fb: remove a bogus dma_free_nonconsistent call
  MAINTAINERS: add entry for dma mapping helpers
  powerpc: merge __dma_set_mask into dma_set_mask
  dma-mapping: remove the set_dma_mask method
  powerpc/cell: use the dma_supported method for ops switching
  powerpc/cell: clean up fixed mapping dma_ops initialization
  tile: remove dma_supported and mapping_error methods
  xen-swiotlb: remove xen_swiotlb_set_dma_mask
  arm: implement ->dma_supported instead of ->set_dma_mask
  mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
  ...
2017-07-06 19:20:54 -07:00
Linus Torvalds 920f2ecdf6 sound updates for 4.13-rc1
This development cycle resulted in a fair amount of changes in both
 core and driver sides.  The most significant change in ALSA core is
 about PCM.  Also the support of of-graph card and the new DAPM widget
 for DSP are noteworthy changes in ASoC core.  And there're lots of
 small changes splat over the tree, as you can see in diffstat.
 
 Below are a few highlights:
 
 ALSA core:
 - Removal of set_fs() hackery from PCM core stuff, and the code
   reorganization / optimization thereafter
 - Improved support of PCM ack ops, and a new ABI for improved
   control/status mmap handling
 - Lots of constifications in various codes
 
 ASoC core:
 - The support of of-graph card, which may work as a better generic
   device for a replacement of simple-card
 - New widget types intended mainly for use with DSPs
 
 ASoC drivers:
 - New drivers for Allwinner V3s SoCs
 - Ensonic ES8316 codec support
 - More Intel SKL and KBL works
 - More device support for Intel SST Atom (mostly for cheap tablets and
   2-in-1 devices)
 - Support for Rockchip PDM controllers
 - Support for STM32 I2S and S/PDIF controllers
 - Support for ZTE AUD96P22 codecs
 
 HD-audio:
 - Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
   for HP and Dell machines
 - A few more fixes for i915 component binding
 
 Note that of-graph change may bring the conflicts with a later pull
 request of devicetree, as currently found in linux-next.
 -----BEGIN PGP SIGNATURE-----
 
 iQJCBAABCAAsFiEECxfAB4MH3rD5mfB6bDGAVD0pKaQFAllbtmMOHHRpd2FpQHN1
 c2UuZGUACgkQbDGAVD0pKaTMkhAAnqvRvh9nYBI1E2VGtJON/AFcsF4s6xdJd0ow
 Bn5Kq/07rGWxAi8Cy69LM930eQrZl+xR69I7LMkC54BxVNhvhXNef7E5GXPbRi+3
 l6dkBmkqvwmmHP5iiOxKtYSAnUfJitu1rmtAOVAjRh8rsWNeLuI8N8V/uilQBioi
 lRywdBjdylub00H1DL8cmZHbrBb4pYrL/LepTswZL3I/UZ225fMiIGFd8tXpQPwZ
 IKRZiuzrc3SykxSsL/aNeyxP+2qTYRtPfl/FGenKBBO2PJmGAb00yAdtQJRcD2eX
 Xf1alfvpNgpy/U6+C7dJgNWQvvr+lPCaFXuMukIDno/zg/xD1V1Ev/fnbVEINLve
 xMOnuJSGGaY6fu6eZ4Cck0VfZIj7UVA9x8zvBOKntIhq/VLfE7DDu3p9tiAZAVfH
 nMOLAhy+0kFyHSrv6zVWQj+cmjPwLvaW7fNWVljL5/MWuF5GJi05DUOfV/vk8BaO
 EnyVqe2ynzNLTsFpLHHy6XKgKtSTkPygxYSNuI7kSYAxD5qE6hXXKXTAqJ3LjDkO
 tGiFmxp/vHrlNvcyRjXc30th/9PPj/mRBcJ2KyjXPa63L5ZW86PiyIHKxJA4yogv
 y4z2ZlhIz90cZvpigFHtFqq1puVlDtKDbAaJ6AKrP8HEHUlMiPNApsSjWWBUcfzV
 DXzrlg0=
 =PUEh
 -----END PGP SIGNATURE-----

Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound

Pull sound updates from Takashi Iwai:
 "This development cycle resulted in a fair amount of changes in both
  core and driver sides. The most significant change in ALSA core is
  about PCM. Also the support of of-graph card and the new DAPM widget
  for DSP are noteworthy changes in ASoC core. And there're lots of
  small changes splat over the tree, as you can see in diffstat.

  Below are a few highlights:

  ALSA core:
   - Removal of set_fs() hackery from PCM core stuff, and the code
     reorganization / optimization thereafter
   - Improved support of PCM ack ops, and a new ABI for improved
     control/status mmap handling
   - Lots of constifications in various codes

  ASoC core:
   - The support of of-graph card, which may work as a better generic
     device for a replacement of simple-card
   - New widget types intended mainly for use with DSPs

  ASoC drivers:
   - New drivers for Allwinner V3s SoCs
   - Ensonic ES8316 codec support
   - More Intel SKL and KBL works
   - More device support for Intel SST Atom (mostly for cheap tablets
     and 2-in-1 devices)
   - Support for Rockchip PDM controllers
   - Support for STM32 I2S and S/PDIF controllers
   - Support for ZTE AUD96P22 codecs

  HD-audio:
   - Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
     for HP and Dell machines
   - A few more fixes for i915 component binding"

* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
  ALSA: hda - Fix unbalance of i915 module refcount
  ASoC: Intel: Skylake: Remove driver debugfs exit
  ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
  ALSA: hda/realtek - Remove GPIO_MASK
  ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
  ALSA: pcm: add a documentation for tracepoints
  ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
  ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
  ASoC: Intel: Skylake: Add support to read firmware registers
  ASoC: Intel: Skylake: Add sram address to sst_addr structure
  ASoC: Intel: Skylake: Debugfs facility to dump module config
  ASoC: Intel: Skylake: Add debugfs support
  ASoC: fix semicolon.cocci warnings
  ASoC: rt5645: Add quirk override by module option
  ASoC: rsnd: make arrays path and cmd_case static const
  ASoC: audio-graph-card: add widgets and routing for external amplifier support
  ASoC: audio-graph-card: update bindings for amplifier support
  ASoC: rt5665: calibration should be done before jack detection
  ASoC: rsnd: constify dev_pm_ops structures.
  ASoC: nau8825: change crosstalk-bypass property to bool type
  ...
2017-07-06 10:56:51 -07:00
Vinod Koul 3edc85023a Merge branch 'topic/rcar' into for-linus 2017-07-04 10:05:22 +05:30
Vinod Koul 2e76eba5e0 Merge branch 'topic/pl330' into for-linus 2017-07-04 10:05:18 +05:30
Vinod Koul 98cd085ebb Merge branch 'topic/pl08x' into for-linus 2017-07-04 10:05:10 +05:30
Vinod Koul 70ef9af765 Merge branch 'topic/mxs' into for-linus 2017-07-04 10:05:01 +05:30
Vinod Koul 87fce2f5f4 Merge branch 'topic/mv_xor' into for-linus 2017-07-04 10:04:48 +05:30
Vinod Koul 930a63485f Merge branch 'topic/dw' into for-linus 2017-07-04 10:04:36 +05:30
Vinod Koul 1326fe64e7 Merge branch 'topic/bcm' into for-linus 2017-07-04 10:04:28 +05:30