Add common platform_device and helper code to make the registration of
the built-in USB controllers easier on the board which are using them.
Also register the USB controller on the AP81 and PB44 boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2442/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The AR724X SoCs have more IRQ sources hooked into the MISC IRQ controller.
The patch adds support for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2440/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The status register of the miscellaneous interrupt controller is 32 bits
wide, but the actual value of NR_IRQS covers only 8 of them. Change
NR_IRQS in order to make all of those interrupt lines usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2441/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: lantiq: use export.h in favour of module.h
MAINTAINERS: The MIPS git tree has moved.
MIPS: Fix build error due to missing inclusion of <linux/export.h>.
MIPS: ASID conflict after CPU hotplug
MIPS: Octeon: Fix compile error in arch/mips/cavium-octeon/flash_setup.c
MIPS: errloongson2_clock: Fix build error by including linux/module.h
STAGING: octeon-ethernet: Fix compile error caused by skb_frag_struct change
MIPS: Hook up process_vm_readv and process_vm_writev system calls.
MIPS: Kernel hangs occasionally during boot.
MIPS: Octeon: Mark SMP-IPI interrupt as IRQF_NO_THREAD
MIPS: BCM47xx: fix build with GENERIC_GPIO configuration
MIPS: NXP: Remove unused source files.
MIPS: Yosemite, Emma: Fix off-by-two in arcs_cmdline buffer size check
The code located at arch/mips/lantiq/ included module.h to be able to use
the EXPORT_SYMBOL* macros. These can now be directly included using
export.h.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I am running SMP Linux 2.6.37-rc1 on BMIPS5000 (single core dual thread)
and observe some abnormalities when doing system suspend/resume which I
narrowed down to cpu hotplugging. The suspend brings the second thread
processor down and then restarts it, after which I see memory corruption
in userspace. I started digging and found out that problem occurs because
while doing execve() the child process is getting the same ASID as the
parent, which obviously corrupts parent's address space.
Further digging showed that activate_mm() calls get_new_mmu_context() to
get a new ASID, but at this time ASID field in entryHi is 1, and
asid_cache(cpu) is 0x100 (it was just reset to ASID_FIRST_VERSION when
the secondary TP was booting).
So, get_new_mmu_context() increments the asid_cache(cpu) value to
0x101, and thus puts 0x01 into entryHi. The result - ASID field does
not get changed as it was supposed to.
My solution is very simple - do not reset asid_cache(cpu) on TP warm
restart.
Patchwork: https://patchwork.linux-mips.org/patch/1797/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The parse_mtd_partitions() and mtd_device_register() functions were
combined into mtd_device_parse_register(). So call that instead.
Signed-off-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following compilation failure with v3.2-rc1 by including module.h:
CC [M] arch/mips/kernel/cpufreq/loongson2_clock.o
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:39:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:51:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:71:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:76:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:82:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:87:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:93:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:131:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:147:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: data definition has no type or storage class [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Werror=implicit-int]
arch/mips/kernel/cpufreq/loongson2_clock.c:166:1: error: parameter names (without types) in function declaration [-Werror]
arch/mips/kernel/cpufreq/loongson2_clock.c:168:15: error: expected declaration specifiers or '...' before string constant
arch/mips/kernel/cpufreq/loongson2_clock.c:169:20: error: expected declaration specifiers or '...' before string constant
arch/mips/kernel/cpufreq/loongson2_clock.c:170:16: error: expected declaration specifiers or '...' before string constant
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2922/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 5f7efb4 (Kbuild: append missing-syscalls to the default target
list) broke MIPS build.
Reported-tested-and-acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The Kernel hangs occasionally during boot after "Calibrating delay loop..".
This is caused by the c0_compare_int_usable() routine in cevt-r4k.c
returning false which causes the system to disable the timer and hang later.
The false return happens because the routine is using a series of four calls
to irq_disable_hazard() as a delay while it waits for the timer changes to
propagate to the cp0 cause register. On newer MIPS cores, like the 74K, the
series of irq_disable_hazard() calls turn into ehb instructions and can take
as little as a few clock ticks for all 4 instructions. This is not enough of
a delay, so the routine thinks the timer is not working. This fix uses up
to a max number of cycle counter ticks for the delay and uses
back_to_back_c0_hazard() instead of irq_disable_hazard() to handle the
hazard condition between cp0 writes and cp0 reads.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to exclude it from force threading to allow RT patch set to work.
And while on this line
* Remove IRQF_DISABLED as as this flag is NOOP
* Add IRQF_PERCPU as this is a per cpu interrupt.
Signed-off-by: Venkat Subbiah <venkat.subbiah@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
To: linux-mips@linux-mips.org
To: linux-rt-users@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/2817/
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since eb9ae7f2 (gpio: fix build error in include/asm-generic/gpio.h)
the generic version of gpio.h calls __gpio_{set,get}_value which we
do not define. Get rid of asm-generic/gpio.h and define the missing
stubs directly for BCM47xx to build.
Reported-by: Ralf Baechle <ralf@linux-mips.org>
To: linux-mips@linux-mips.org
CC: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2885/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cause is a misplaced bracket.
The code
strlen(buf+1)
will be two bytes less than
strlen(buf)+1
The +1 is in this code to reserve space for an additional space character.
[ralf@linux-mips.org: Thomas' original patch fixed the issue only for
Yosemite but the same bug exists also in Emma.]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Patchwork: https://patchwork.linux-mips.org/patch/2861/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scsi: drop unused Kconfig symbol
pci: drop unused Kconfig symbol
stmmac: drop unused Kconfig symbol
x86: drop unused Kconfig symbol
powerpc: drop unused Kconfig symbols
powerpc: 40x: drop unused Kconfig symbol
mips: drop unused Kconfig symbols
openrisc: drop unused Kconfig symbols
arm: at91: drop unused Kconfig symbol
samples: drop unused Kconfig symbol
m32r: drop unused Kconfig symbol
score: drop unused Kconfig symbols
sh: drop unused Kconfig symbol
um: drop unused Kconfig symbol
sparc: drop unused Kconfig symbol
alpha: drop unused Kconfig symbol
Fix up trivial conflict in drivers/net/ethernet/stmicro/stmmac/Kconfig
as per Michal: the STMMAC_DUAL_MAC config variable is still unused and
should be deleted.
* 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits)
i2c-s3c2410: Add device tree support
i2c-s3c2410: Keep a copy of platform data and use it
i2c-nomadik: cosmetic coding style corrections
i2c-au1550: dev_pm_ops conversion
i2c-au1550: increase timeout waiting for master done
i2c-au1550: remove unused ack_timeout
i2c-au1550: remove usage of volatile keyword
i2c-tegra: __iomem annotation fix
i2c-eg20t: Add initialize processing in case i2c-error occurs
i2c-eg20t: Fix flag setting issue
i2c-eg20t: add stop sequence in case wait-event timeout occurs
i2c-eg20t: Separate error processing
i2c-eg20t: Fix 10bit access issue
i2c-eg20t: Modify returned value s32 to long
i2c-eg20t: Fix bus-idle waiting issue
i2c-designware: Fix PCI core warning on suspend/resume
i2c-designware: Add runtime power management support
i2c-designware: Add support for Designware core behind PCI devices.
i2c-designware: Push all register reads/writes into the core code.
i2c-designware: Support multiple cores using same ISR
...
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
None of these files are using modular infrastructure, and build
tests reveal that none of these files are really relying on any
implicit inclusions via. module.h either. So delete them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files are not modules, but were including module.h only for
EXPORT_SYMBOL and/or THIS_MODULE. Now that we have the lightweight
export.h, use it in these kinds of cases.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We need to call out inclusion of smp.h, or with the module.h cleanup
we'll get things like:
arch/mips/loongson/common/platform.c:21: error: implicit declaration of function 'smp_processor_id'
arch/mips/vr41xx/common/giu.c:84: error: implicit declaration of function 'smp_processor_id'
arch/mips/vr41xx/common/rtc.c:85: error: implicit declaration of function 'smp_processor_id'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We are relying on asm/elf.h being present implicitly. Once we clean
up the root cause of that, we'll see this, so fix it in advance.
arch/mips/kernel/cpu-probe.c: In function 'set_elf_platform':
arch/mips/kernel/cpu-probe.c:298: error: '__elf_platform' undeclared (first use in this function)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Replace the usage of "volatile"s with register accessor functions.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
leases: fix write-open/read-lease race
nfs: drop unnecessary locking in llseek
ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
vfs: add generic_file_llseek_size
vfs: do (nearly) lockless generic_file_llseek
direct-io: merge direct_io_walker into __blockdev_direct_IO
direct-io: inline the complete submission path
direct-io: separate map_bh from dio
direct-io: use a slab cache for struct dio
direct-io: rearrange fields in dio/dio_submit to avoid holes
direct-io: fix a wrong comment
direct-io: separate fields only used in the submission path from struct dio
vfs: fix spinning prevention in prune_icache_sb
vfs: add a comment to inode_permission()
vfs: pass all mask flags check_acl and posix_acl_permission
vfs: add hex format for MAY_* flag values
vfs: indicate that the permission functions take all the MAY_* flags
compat: sync compat_stats with statfs.
vfs: add "device" tag to /proc/self/mountstats
cleanup: vfs: small comment fix for block_invalidatepage
...
Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
This was found by inspection while tracking a similar
bug in compat_statfs64, that has been fixed in mainline
since decemeber.
- This fixes a bug where not all of the f_spare fields
were cleared on mips and s390.
- Add the f_flags field to struct compat_statfs
- Copy f_flags to userspace in case someone cares.
- Use __clear_user to copy the f_spare field to userspace
to ensure that all of the elements of f_spare are cleared.
On some architectures f_spare is has 5 ints and on some
architectures f_spare only has 4 ints. Which makes
the previous technique of clearing each int individually
broken.
I don't expect anyone actually uses the old statfs system
call anymore but if they do let them benefit from having
the compat and the native version working the same.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
Later IRIX versions provide them in <sys/regdef.h> and gas also accepts
$ta0 .. $ta3 since binutils 2.18 so Linux should do the same for source
compatibility.
The hard coded constants are moved to struct mips_pmu. All counter
register access move to the read_counter and write_counter function
pointers, which are set to either 32-bit or 64-bit access methods at
initialization time.
Many of the function pointers in struct mips_pmu were not needed as
there was only a single implementation, these were removed.
I couldn't figure out what made struct cpu_hw_events.msbs[] at all
useful, so I removed it too.
Some functions and other declarations were reordered to reduce the
need for forward declarations.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The contents of arch/mips/kernel/perf_event.c and
arch/mips/kernel/perf_event_mipsxx.c were divided in a seemingly ad
hoc manner, with the first including the second.
I moved all the hardware counter support code to perf_event_mipsxx.c
and removed the gating #ifdefs to the Kconfig and Makefile.
Now perf_event.c contains only the callchain support, everything else
is in perf_event_mipsxx.c
There are no code changes, only moving of functions from one file to
the other, or removing empty unneeded functions.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Dezhong Diao <dediao@cisco.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2791/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Get rid of a bunch of useless inline declarations, and join a bunch of
improperly split lines.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2793/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It seems that BSP could be setup twice, but the nlm_cpu_ready array is only
set for ASPs in smpboot.S, not including BSP.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Cc: "Jayachandran C." <jayachandranc@netlogicmicro.com>
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2695/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>,
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch gets rid of all CONFIG_SOC_AU1XXX defines in
DMA/DBDMA-related code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xxx-ide uses defines from the pb1200/db1200 headers:
get DBDMA ID through platform resource information,
hardcode register spacing. The only 2 users of this driver (and
the only boards it can really work on realiably) use the same
register layout.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-ide@vger.kernel.org
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-ide@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/2716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gabor Juhos