On Amlogic GX SoCs, there is two CEC controllers :
- An Amlogic CEC custom in the AO domain
- The Synopsys HDMI-TX Controller in the EE domain
Each of these controllers needs a 32.768KHz clock, but there is two paths :
- In the EE domain, the "32k_clk" this patchs is adding
- In the AO domain, with a more complex dual divider more precise setup
The AO 32K clock support will be pushed later in the corresponding
gxbb-aoclk driver when the AE CEC driver is ready.
The EE 32k_clk must be pushed earlier since mainline support for CEC in the
Synopsys HDMI-TX controller is nearby.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Rebased patch on top of last changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
clk81 already has CLK_IS_CRITICAL so CLK_IGNORE_UNUSED is not
necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Disabling clk81 results in an immediate freeze of the whole system. This
can happen "accidentally" when the last child-clock of clk81 is disabled
(in this case the common clock framework also disables clk81, even if it
was only enabled indirectly before).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
It seems that the "cpu_clk" was carried over from the meson8b clock
controller driver. On Meson GX (GXBB/GXL/GXM) the registers which are
used by the cpu_clk have a different purpose (in other words: they don't
control the CPU clock anymore). HHI_SYS_CPU_CLK_CNTL1 bits 31:24 are
reserved according to the public S905 datasheet, while bit 23 is the
"A53_trace_clk_DIS" gate (which according to the datasheet should only
be used in case a silicon bug is discovered) and bits 22:20 are a
divider (A53_trace_clk). The meson clk-cpu code however expects that
bits 28:20 are reserved for a divider (according to the public S805
datasheet this "SCALE_DIV: This value represents an N+1 divider of the
input clock.").
The CPU clock on Meson GX SoCs is provided by the SCPI DVFS clock
driver instead. Two examples from a Meson GXL S905X SoC:
- vcpu (SCPI DVFS clock 0) rate: 1000000000 / cpu_clk rate: 708000000
- vcpu (SCPI DVFS clock 0) rate: 1512000000 / cpu_clk rate: 708000000
Unfortunately the CLKID_CPUCLK was already exported (but is currently
not used) to DT. Due to the removal of this clock definition there is
now a hole in the clk_hw_onecell_data (which is not a problem because
this case is already handled in gxbb_clkc_probe).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The CPU clock defined in the Meson GX clock driver is actually a
left-over from the Meson8b clock controller. Un-export the clock so we
can remove it from the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock ids of the three none AO uarts to the dt-bindings
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy the commit message to match similar change]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the SPICC gate clock to enable the SPICC controller.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy commit message to match similar changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the spdif master clock and the mux to select the appropriate spdif
clock parent depending on the data source.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock gates required for the spdif output
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
AHB BIST gate is actually controlled with bit 7.
This bug was detected while trying to use the NAND controller which is
using the DMA engine to transfer data to the NAND.
Since the ahb_bist_clk gate bit conflicts with the ahb_dma_clk gate bit,
the core was disabling the DMA engine clock as part of its 'disable
unused clks' procedure, which was causing all DMA transfers to fail after
this point.
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Cc: stable@vger.kernel.org
Reported-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1495643669-28221-1-git-send-email-boris.brezillon@free-electrons.com
Add a new R-Car E2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car V2H Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car M2-W/N Clock Pulse Generator / Module Standby and
Software Reset driver, using the CPG/MSSR driver core. This will enable
support for module resets, which are not supported by the existing
driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a new R-Car H2 Clock Pulse Generator / Module Standby and Software
Reset driver, using the CPG/MSSR driver core. This will enable support
for module resets, which are not supported by the existing driver.
The old driver can still be used through a Kconfig option, to preserve
backward compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Document use of the Renesas Clock Pulse Generator / Module Standby and
Software Reset DT Bindings for various member of the R-Car Gen2 family
(H2, M2-W, V2H, M2-N, and E2).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
The goals are to:
- Allow precise control over and automatic selection of which
(sub)drivers are used for which SoC (which may change in the
future),
- Allow adding support for new SoCs easily,
- Allow compile-testing of all (sub)drivers,
- Keep driver selection logic in the subsystem-specific Kconfig,
independent from the architecture-specific Kconfig (i.e. no "select"
from arch/arm64/Kconfig.platforms), to avoid dependencies.
This is implemented by:
- Introducing Kconfig symbols for all drivers and sub-drivers,
- Introducing the Kconfig symbol CLK_RENESAS, which is enabled
automatically when building for a Renesas ARM platform, and which
enables all required drivers without interaction of the user, based
on SoC-specific ARCH_* symbols,
- Allowing the user to enable any Kconfig symbol manually if
COMPILE_TEST is enabled,
- Using the new Kconfig symbols instead of the ARCH_* symbols to
control compilation in the Makefile,
- Always entering drivers/clk/renesas/ during the build.
Note that currently not all (sub)drivers are enabled for
compile-testing, as they depend on independent fixes in other
subsystems.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Coccinelle warns:
drivers/clk/renesas/renesas-cpg-mssr.c:323:14-21: ERROR: PTR_ERR applied after initialization to constant on line 260
Initialize clk using ERR_PTR(-ENOTSUPP) instead of NULL to fix this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
support more cpu freq, and add armcore div setting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch exports related BUS/VPU/RGA/HDCP/IEP/TSP/WIFI/
VIO/USB/EFUSE/GPU/CRYPTO clocks for dts reference.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
we use SCLK_TESTCLKOUT1 and SCLK_TESTCLKOUT2 for camera, so add those ids.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With CONFIG_RESET_CONTROLLER=n we see the following link error in the
meson gxbb clk driver:
drivers/built-in.o: In function 'gxbb_aoclkc_probe':
drivers/clk/meson/gxbb-aoclk.c:161: undefined reference to 'devm_reset_controller_register'
Fix this by selecting the reset controller subsystem.
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: Added fixes-by tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cfr. the errata of April 14, 2017, for the R-Car Gen3 Hardware Manual
Rev. 0.53E.
These have no user-visible effect, as the clock frequencies stay the
same.
Fixes: 5573d19412 ("clk: renesas: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The pm_subsys_data.clock_list member exists only if CONFIG_PM_CLK=y.
Hence direct accesses to this field break compile-testing on platforms
where CONFIG_PM_CLK=n.
To fix this, use the pm_clk_no_clocks() helper instead, for which a
dummy version is provided if CONFIG_PM_CLK=n.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
R-Car V2H does not have "DIV6" programmable clocks, hence there is no
need to build clk-div6.o.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the "intc-ex" clock to the R8A7796 CPG MSSR driver.
According to information from the hardware team the INTC-EX
parent clock is CP. The next data sheet version will include
this information.
[takeshi.kihara.df: Ported from commit f099aa0757 ("clk: shmobile:
r8a7795: Add INTC-EX clock") to drivers/clk/renesas/r8a7796-cpg-mssr.c]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to tables 7.5b and 7.6b of the RZ/G Series Hardware User's
Manual Rev.1.00, MD19=0 is a prohibited setting.
Hence stop looking at MD19, and remove all PLL configurations for
MD19=0.
Fixes: 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RZ/G1E does not have the SCU-SRC[0789] modules and module clocks.
Fixes: 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car V2H and E2 do not have the PLL0CR register, but use a fixed
multiplier (depending on mode pins) and divider.
This corrects the clock rate of "pll0" (PLL0 VCO after post divider) on
R-Car V2H and E2 from 1.5 GHz to 1 GHz.
Inspired by Sergei Shtylyov's work for the common R-Car Gen2 and RZ/G
Clock Pulse Generator support core.
Fixes: 7c4163aae3 ("ARM: dts: r8a7792: initial SoC device tree")
Fixes: 0dce5454d5 ("ARM: shmobile: Initial r8a7794 SoC device tree")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pull some more input subsystem updates from Dmitry Torokhov:
"An updated xpad driver with a few more recognized device IDs, and a
new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads
via SPI bus"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cros_ec_keyb - remove extraneous 'const'
Input: add support for PlayStation 1/2 joypads connected via SPI
Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth
Input: xpad - sync supported devices with xboxdrv
Input: xpad - sort supported devices by USB ID
Neil Armstrong