Commit Graph

580 Commits

Author SHA1 Message Date
Rafael J. Wysocki bde091ece2 cpuidle: menu: Simplify checks related to the polling state
After some recent menu governor changes, the promotion of the
"polling" state to a physical one is mostly controlled by the
latency limit (resulting from the "interactivity" factor) and
not by the time to the closest timer event, so it should be
sufficient to check the exit latency of that state for this
purpose (of course, its target residency still needs to be
within the next timer event range for energy-efficiency).

Also, the physical state the "polling" one is promoted to need not
be the next one in principle (in case the next state is disabled,
for example).

For these reasons, simplify the checks made to decide whether or
not to promote the "polling" state to a physical one and update
the target idle duration when it is promoted in case the residency
of the new state turns out to be above the tick boundary (in which
case there is no reason to stop the tick).

Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-10-12 10:46:37 +02:00
Rafael J. Wysocki 01bad1c689 cpuidle: poll_state: Revise loop termination condition
If need_resched() returns "false", breaking out of the loop in
poll_idle() will cause a new idle state to be selected, so in fact
it usually doesn't make sense to spin in it longer than the target
residency of the second state.  [Note that the "polling" state is
used only if there is at least one "real" state defined in addition
to it, so the second state is always there.]  On the other hand,
breaking out of it early (say in case the next state is disabled)
shouldn't hurt as it is polling anyway.

For this reason, make the loop in poll_idle() break if the CPU has
been spinning longer than the target residency of the second state
(the "polling" state can only be state[0]).

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-10-04 19:27:27 +02:00
Rafael J. Wysocki 53812cdc91 cpuidle: menu: Move the latency_req == 0 special case check
It is better to always update data->bucket before returning from
menu_select() to avoid updating the correction factor for a stale
bucket, so combine the latency_req == 0 special check with the more
general check below.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2018-10-04 19:27:27 +02:00
Rafael J. Wysocki 8b007ebec9 cpuidle: menu: Avoid computations for very close timers
If the next timer event (not including the tick) is closer than the
target residency of the second state or the PM QoS latency constraint
is below its exit latency, state[0] will be used regardless of any
other factors, so skip the computations in menu_select() then and
return 0 straight away from it.

Still, do that after the bucket has been determined to avoid
updating the correction factor for a stale bucket.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2018-10-04 19:27:27 +02:00
Rafael J. Wysocki eb40a380bf cpuidle: menu: Do not update last_state_idx in menu_select()
It is not necessary to update data->last_state_idx in menu_select()
as it only is used in menu_update() which only runs when
data->needs_update is set and that is set only when updating
data->last_state_idx in menu_reflect().

Accordingly, drop the update of data->last_state_idx from
menu_select() and get rid of the (now redundant) "out" label
from it.

No intentional behavior changes.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2018-10-04 19:26:38 +02:00
Rafael J. Wysocki 96c3d11df1 cpuidle: menu: Get rid of first_idx from menu_select()
Rearrange the code in menu_select() so that the loop over idle states
always starts from 0 and get rid of the first_idx variable.

While at it, add two empty lines to separate conditional statements
from one another.

No intentional behavior changes.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2018-10-04 19:25:53 +02:00
Rafael J. Wysocki 23e8ceb9ce cpuidle: menu: Compute first_idx when latency_req is known
Since menu_select() can only set first_idx to 1 if the exit latency
of the second state is not greater than the latency limit, it should
first determine that limit.  Thus first_idx should be computed after
the "interactivity" factor has been taken into account.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewedy-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2018-10-04 19:24:14 +02:00
Rafael J. Wysocki 5f26bdceb9 cpuidle: menu: Fix wakeup statistics updates for polling state
If the CPU exits the "polling" state due to the time limit in the
loop in poll_idle(), this is not a real wakeup and it just means
that the "polling" state selection was not adequate.  The governor
mispredicted short idle duration, but had a more suitable state been
selected, the CPU might have spent more time in it.  In fact, there
is no reason to expect that there would have been a wakeup event
earlier than the next timer in that case.

Handling such cases as regular wakeups in menu_update() may cause the
menu governor to make suboptimal decisions going forward, but ignoring
them altogether would not be correct either, because every time
menu_select() is invoked, it makes a separate new attempt to predict
the idle duration taking distinct time to the closest timer event as
input and the outcomes of all those attempts should be recorded.

For this reason, make menu_update() always assume that if the
"polling" state was exited due to the time limit, the next proper
wakeup event for the CPU would be the next timer event (not
including the tick).

Fixes: a37b969a61 "cpuidle: poll_state: Add time limit to poll_idle()"
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2018-10-04 10:23:37 +02:00
Rafael J. Wysocki 03dba27804 cpuidle: menu: Replace data->predicted_us with local variable
The predicted_us field in struct menu_device is only accessed in
menu_select(), so replace it with a local variable in that function.

With that, stop using expected_interval instead of predicted_us to
store the new predicted idle duration value if it is set to the
selected state's target residency which is quite confusing.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2018-10-03 12:02:44 +02:00
Fieah Lim 7037b43e00 cpuidle: enter_state: Don't needlessly calculate diff time
Currently, ktime_us_delta() is invoked unconditionally to compute the
idle residency of the CPU, but it only makes sense to do that if a
valid idle state has been entered, so move the ktime_us_delta()
invocation after the entered_state >= 0 check.

While at it, merge two comment blocks in there into one and drop
a space between type casting of diff.

This patch has no functional changes.

Signed-off-by: Fieah Lim <kw@fieahl.im>
[ rjw: Changelog cleanup, comment format fix ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-09-18 09:32:56 +02:00
Fieah Lim 6a5f95b5a4 cpuidle: Remove unnecessary wrapper cpuidle_get_last_residency()
cpuidle_get_last_residency() is just a wrapper for retrieving
the last_residency member of struct cpuidle_device.  It's also
weirdly the only wrapper function for accessing cpuidle_* struct
member (by my best guess is it could be a leftover from v2.x).

Anyhow, since the only two users (the ladder and menu governors)
can access dev->last_residency directly, and it's more intuitive to
do it that way, let's just get rid of the wrapper.

This patch tidies up CPU idle code a bit without functional changes.

Signed-off-by: Fieah Lim <kw@fieahl.im>
[ rjw: Changelog cleanup ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-09-18 09:24:44 +02:00
Rafael J. Wysocki 757ab15c3f cpuidle: menu: Retain tick when shallow state is selected
The case addressed by commit 5ef499cd57 (cpuidle: menu: Handle
stopped tick more aggressively) in the stopped tick case is present
when the tick has not been stopped yet too.  Namely, if only two CPU
idle states, shallow state A with target residency significantly
below the tick boundary and deep state B with target residency
significantly above it, are available and the predicted idle
duration is above the tick boundary, but below the target residency
of state B, state A will be selected and the CPU may spend indefinite
amount of time in it, which is not quite energy-efficient.

However, if the tick has not been stopped yet and the governor is
about to select a shallow idle state for the CPU even though the idle
duration predicted by it is above the tick boundary, it should be
fine to wake up the CPU early, so the tick can be retained then and
the governor will have a chance to select a deeper state when it runs
next time.

[Note that when this really happens, it will make the idle duration
 predictor believe that the CPU might be idle longer than predicted,
 which will make it more likely to predict longer idle durations going
 forward, but that will also cause deeper idle states to be selected
 going forward, on average, which is what's needed here.]

Fixes: 87c9fe6ee4 (cpuidle: menu: Avoid selecting shallow states with stopped tick)
Reported-by: Leo Yan <leo.yan@linaro.org>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+: 5ef499cd57 (cpuidle: menu: Handle ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-08-25 13:16:08 +02:00
Linus Torvalds dfec4a8478 More power management updates for 4.19-rc1
- Make the idle loop handle stopped scheduler tick correctly (Rafael
    Wysocki).
 
  - Prevent the menu cpuidle governor from letting CPUs spend too much
    time in shallow idle states when it is invoked with scheduler tick
    stopped and clean it up somewhat (Rafael Wysocki).
 
  - Avoid invoking the platform firmware to make the platform enter
    the ACPI S3 sleep state with suspended PCIe root ports which may
    confuse the firmware and cause it to crash (Rafael Wysocki).
 
  - Fix sysfs-related race in the ondemand and conservative cpufreq
    governors which may cause the system to crash if the governor
    module is removed during an update of CPU frequency limits (Henry
    Willard).
 
  - Select SRCU when building the system wakeup framework to avoid a
    build issue in it (zhangyi).
 
  - Make the descriptions of ACPI C-states vendor-neutral to avoid
    confusion (Prarit Bhargava).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJbfSnVAAoJEILEb/54YlRxBn4QAKQ8PqkSYkBby+1hb90ET4dk
 VaLkbCYXuzLK5rIDvnbYOALhVKo4B29Ex5GdCLN7cWkZMkrVKe7oX8QQTnp3/7lF
 URjTKgTNec5uJG652PrE3ESAa3X/kYggj6aeQOxDR4iYKzcpJEQ92ekFW+SoJTNp
 Jc2kZh3qkC2On64GB3ibsZaKnmHfPvLg0t4agwzuYq/Gff8NRJFk7kMwAPzqGzZo
 b2UVRcYFWIRkJjgmU9iInoeHIY8mBdT3IiKwTemZP1dOhb5T1AHOXwGTk6/cS+RH
 A9qx4eg7I3R00KmnYvO8WytYJeOu2qb83GIUx4fIJGOqfvevm5xkxB9F+nfE+ouj
 ROBqO4+X4XfQGPw8slayg0rJjI9JSkXLnLdl0Qw2WRlbc4/fVWntra1C57EeKFBR
 EG9UAF9+7nUUx0bOCLsfFF3+r9R3SDUjk7b4thyhYncyQRsYC+FL7ztlxnMzVtzW
 M5SF2sPrpcQzqmcszdUdbESI10n5X8m/crJW4rsbTxBpAM+coO+uLcvHWOY4MpkW
 BgBsR6bMDAlG/VlTFgeeP/tkCRd5zNlJi7yBFItXuOoVKXpnHCJuxq2WkZ1Rb74M
 Gk1d3TduekHJm8VsLEdCJR/tEk1cMc0zVUD/a1yzI4Z21QxvXUCqMDdws4/Ey184
 qmKgNR9R94vSC5xIPRhM
 =9GrU
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull more power management updates from Rafael Wysocki:
 "These fix the main idle loop and the menu cpuidle governor, clean up
  the latter, fix a mistake in the PCI bus type's support for system
  suspend and resume, fix the ondemand and conservative cpufreq
  governors, address a build issue in the system wakeup framework and
  make the ACPI C-states desciptions less confusing.

  Specifics:

   - Make the idle loop handle stopped scheduler tick correctly (Rafael
     Wysocki).

   - Prevent the menu cpuidle governor from letting CPUs spend too much
     time in shallow idle states when it is invoked with scheduler tick
     stopped and clean it up somewhat (Rafael Wysocki).

   - Avoid invoking the platform firmware to make the platform enter the
     ACPI S3 sleep state with suspended PCIe root ports which may
     confuse the firmware and cause it to crash (Rafael Wysocki).

   - Fix sysfs-related race in the ondemand and conservative cpufreq
     governors which may cause the system to crash if the governor
     module is removed during an update of CPU frequency limits (Henry
     Willard).

   - Select SRCU when building the system wakeup framework to avoid a
     build issue in it (zhangyi).

   - Make the descriptions of ACPI C-states vendor-neutral to avoid
     confusion (Prarit Bhargava)"

* tag 'pm-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: menu: Handle stopped tick more aggressively
  sched: idle: Avoid retaining the tick when it has been stopped
  PCI / ACPI / PM: Resume all bridges on suspend-to-RAM
  cpuidle: menu: Update stale polling override comment
  cpufreq: governor: Avoid accessing invalid governor_data
  x86/ACPI/cstate: Make APCI C1 FFH MWAIT C-state description vendor-neutral
  cpuidle: menu: Fix white space
  PM / sleep: wakeup: Fix build error caused by missing SRCU support
2018-08-22 07:42:36 -07:00
Rafael J. Wysocki 5ef499cd57 cpuidle: menu: Handle stopped tick more aggressively
Commit 87c9fe6ee4 (cpuidle: menu: Avoid selecting shallow states
with stopped tick) missed the case when the target residencies of
deep idle states of CPUs are above the tick boundary which may cause
the CPU to get stuck in a shallow idle state for a long time.

Say there are two CPU idle states available: one shallow, with the
target residency much below the tick boundary and one deep, with
the target residency significantly above the tick boundary.  In
that case, if the tick has been stopped already and the expected
next timer event is relatively far in the future, the governor will
assume the idle duration to be equal to TICK_USEC and it will select
the idle state for the CPU accordingly.  However, that will cause the
shallow state to be selected even though it would have been more
energy-efficient to select the deep one.

To address this issue, modify the governor to always use the time
till the closest timer event instead of the predicted idle duration
if the latter is less than the tick period length and the tick has
been stopped already.  Also make it extend the search for a matching
idle state if the tick is stopped to avoid settling on a shallow
state if deep states with target residencies above the tick period
length are available.

In addition, make it always indicate that the tick should be stopped
if it has been stopped already for consistency.

Fixes: 87c9fe6ee4 (cpuidle: menu: Avoid selecting shallow states with stopped tick)
Reported-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-08-20 13:37:03 +02:00
Linus Torvalds 5e2d059b52 powerpc updates for 4.19
Notable changes:
 
  - A fix for a bug in our page table fragment allocator, where a page table page
    could be freed and reallocated for something else while still in use, leading
    to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
    a powerpc only refcount.
 
  - Fixes to our pkey support. Several are user-visible changes, but bring us in
    to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
    for reporting many of these.
 
  - A series to improve the hvc driver & related OPAL console code, which have
    been seen to cause hardlockups at times. The hvc driver changes in particular
    have been in linux-next for ~month.
 
  - Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
 
  - Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
    anywhere other than as a paper weight.
 
  - An optimised memcmp implementation using Power7-or-later VMX instructions
 
  - Support for barrier_nospec on some NXP CPUs.
 
  - Support for flushing the count cache on context switch on some IBM CPUs
    (controlled by firmware), as a Spectre v2 mitigation.
 
  - A series to enhance the information we print on unhandled signals to bring it
    into line with other arches, including showing the offending VMA and dumping
    the instructions around the fault.
 
 Thanks to:
   Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
   Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
   Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
   Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
   Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
   Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
   Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
   Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
   Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
   Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
   Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
   Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
   Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
   Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
   Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
   B, zhong jiang.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCgAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAlt2O6cTHG1wZUBlbGxl
 cm1hbi5pZC5hdQAKCRBR6+o8yOGlgC7hD/4+cj796Df7GsVsIMxzQm7SS9dklIdO
 JuKj2Nr5HRzTH59jWlXukLG9mfTNCFgFJB4gEpK1ArDOTcHTCI9RRsLZTZ/kum66
 7Pd+7T40dLYXB5uecuUs0vMXa2fI3syKh1VLzACSXv3Dh9BBIKQBwW/aD2eww4YI
 1fS5LnXZ2PSxfr6KNAC6ogZnuaiD0sHXOYrtGHq+S/TFC7+Z6ySa6+AnPS+hPVoo
 /rHDE1Khr66aj7uk+PP2IgUrCFj6Sbj6hTVlS/iAuwbMjUl9ty6712PmvX9x6wMZ
 13hJQI+g6Ci+lqLKqmqVUpXGSr6y4NJGPS/Hko4IivBTJApI+qV/tF2H9nxU+6X0
 0RqzsMHPHy13n2torA1gC7ttzOuXPI4hTvm6JWMSsfmfjTxLANJng3Dq3ejh6Bqw
 76EMowpDLexwpy7/glPpqNdsP4ySf2Qm8yq3mR7qpL4m3zJVRGs11x+s5DW8NKBL
 Fl5SqZvd01abH+sHwv6NLaLkEtayUyohxvyqu2RU3zu5M5vi7DhqstybTPjKPGu0
 icSPh7b2y10WpOUpC6lxpdi8Me8qH47mVc/trZ+SpgBrsuEmtJhGKszEnzRCOqos
 o2IhYHQv3lQv86kpaAFQlg/RO+Lv+Lo5qbJ209V+hfU5nYzXpEulZs4dx1fbA+ze
 fK8GEh+u0L4uJg==
 =PzRz
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "Notable changes:

   - A fix for a bug in our page table fragment allocator, where a page
     table page could be freed and reallocated for something else while
     still in use, leading to memory corruption etc. The fix reuses
     pt_mm in struct page (x86 only) for a powerpc only refcount.

   - Fixes to our pkey support. Several are user-visible changes, but
     bring us in to line with x86 behaviour and/or fix outright bugs.
     Thanks to Florian Weimer for reporting many of these.

   - A series to improve the hvc driver & related OPAL console code,
     which have been seen to cause hardlockups at times. The hvc driver
     changes in particular have been in linux-next for ~month.

   - Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.

   - Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
     use anywhere other than as a paper weight.

   - An optimised memcmp implementation using Power7-or-later VMX
     instructions

   - Support for barrier_nospec on some NXP CPUs.

   - Support for flushing the count cache on context switch on some IBM
     CPUs (controlled by firmware), as a Spectre v2 mitigation.

   - A series to enhance the information we print on unhandled signals
     to bring it into line with other arches, including showing the
     offending VMA and dumping the instructions around the fault.

  Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
  Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
  Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
  Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
  Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
  Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
  Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
  Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
  Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
  Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
  Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
  Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
  Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
  Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
  Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
  Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
  Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
  Rao, zhong jiang"

* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
  powerpc/mm/book3s/radix: Add mapping statistics
  powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
  powerpc/mm/hash: Remove unnecessary do { } while(0) loop
  powerpc/64s: move machine check SLB flushing to mm/slb.c
  powerpc/powernv/idle: Fix build error
  powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
  powerpc/mm: remove warning about ‘type’ being set
  powerpc/32: Include setup.h header file to fix warnings
  powerpc: Move `path` variable inside DEBUG_PROM
  powerpc/powermac: Make some functions static
  powerpc/powermac: Remove variable x that's never read
  cxl: remove a dead branch
  powerpc/powermac: Add missing include of header pmac.h
  powerpc/kexec: Use common error handling code in setup_new_fdt()
  powerpc/xmon: Add address lookup for percpu symbols
  powerpc/mm: remove huge_pte_offset_and_shift() prototype
  powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
  powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
  powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
  powerpc/fadump: handle crash memory ranges array index overflow
  ...
2018-08-17 11:32:50 -07:00
Rafael J. Wysocki 50f7ccc647 cpuidle: menu: Update stale polling override comment
The comment to explain why the menu governor uses idle state 1
instead of idle state 0 as the first one sometimes is stale (among
other things it mentions a user setting not present any more),
so update it.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-08-16 23:05:43 +02:00
Rafael J. Wysocki f390c5eb28 cpuidle: menu: Fix white space
Fix some damaged white space in menu_select().

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-08-15 00:08:51 +02:00
Akshay Adiga 1961acad2f powernv/cpuidle: Use parsed device tree values for cpuidle_init
Export pnv_idle_states and nr_pnv_idle_states so that its accessible to
cpuidle driver. Use properties from pnv_idle_states structure for powernv
cpuidle_init.

Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2018-07-31 19:56:44 +10:00
Sudeep Holla 818489e511 ARM: cpuidle: silence error on driver registration failure
It's perfectly fine to have multiple cpuidle driver compiled in the
build configuration. However, it's not good to throw error on driver
registration failure if some other driver is already initialised and
assigned. In such cases, __cpuidle_register_driver returns -EBUSY and
we can check for such error before throwing the error.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-06-25 09:33:34 +02:00
Linus Torvalds c90fca951e powerpc updates for 4.18
Notable changes:
 
  - Support for split PMD page table lock on 64-bit Book3S (Power8/9).
 
  - Add support for HAVE_RELIABLE_STACKTRACE, so we properly support live
    patching again.
 
  - Add support for patching barrier_nospec in copy_from_user() and syscall entry.
 
  - A couple of fixes for our data breakpoints on Book3S.
 
  - A series from Nick optimising TLB/mm handling with the Radix MMU.
 
  - Numerous small cleanups to squash sparse/gcc warnings from Mathieu Malaterre.
 
  - Several series optimising various parts of the 32-bit code from Christophe Leroy.
 
  - Removal of support for two old machines, "SBC834xE" and "C2K" ("GEFanuc,C2K"),
    which is why the diffstat has so many deletions.
 
 And many other small improvements & fixes.
 
 There's a few out-of-area changes. Some minor ftrace changes OK'ed by Steve, and
 a fix to our powernv cpuidle driver. Then there's a series touching mm, x86 and
 fs/proc/task_mmu.c, which cleans up some details around pkey support. It was
 ack'ed/reviewed by Ingo & Dave and has been in next for several weeks.
 
 Thanks to:
   Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al Viro, Andrew
   Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Balbir Singh,
   Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King, Dave
   Hansen, Fabio Estevam, Finn Thain, Frederic Barrat, Gautham R. Shenoy, Haren
   Myneni, Hari Bathini, Ingo Molnar, Jonathan Neuschäfer, Josh Poimboeuf,
   Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu
   Malaterre, Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
   Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
   Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica Gupta, Ravi
   Bangoria, Russell Currey, Sam Bobroff, Samuel Mendoza-Jonas, Segher
   Boessenkool, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stewart Smith,
   Thiago Jung Bauermann, Torsten Duwe, Vaibhav Jain, Wei Yongjun, Wolfram Sang,
   Yisheng Xie, YueHaibing.
 -----BEGIN PGP SIGNATURE-----
 
 iQIwBAABCAAaBQJbGQKBExxtcGVAZWxsZXJtYW4uaWQuYXUACgkQUevqPMjhpYBq
 TRAAioK7rz5xYMkxaM3Ng3ybobEeNAwQqOolz98xvmnB9SfDWNuc99vf8cGu0/fQ
 zc8AKZ5RcnwipOjyGlxW9oa1ZhVq0xtYnQPiYLEKMdLQmh5D+C7+KpvAd1UElweg
 ub40/xDySWfMujfuMSF9JDCWPIXyojt4Xg5nJKIVRrAm/3YMe/+i5Am7NWHuMCEb
 aQmZtlYW5Mz81XY0968hjpUO6eKFRmsaM7yFAhGTXx6+oLRpGj1PZB4AwdRIKS2L
 Ak7q/VgxtE4W+s3a0GK2s+eXIhGKeFuX9AVnx3nti+8/K1OqrqhDcLMUC/9JpCpv
 EvOtO7dxPnZujHjdu4Eai/xNoo4h6zRy7bWqve9LoBM40CP5jljKzu1lwqqb5yO0
 jC7/aXhgiSIxxcRJLjoI/TYpZPu40MifrkydmczykdPyPCnMIWEJDcj4KsRL/9Y8
 9SSbJzRNC/SgQNTbUYPZFFi6G0QaMmlcbCb628k8QT+Gn3Xkdf/ZtxzqEyoF4Irq
 46kFBsiSSK4Bu0rVlcUtJQLgdqytWULO6NKEYnD67laxYcgQd8pGFQ8SjZhRZLgU
 q5LA3HIWhoAI4M0wZhOnKXO6JfiQ1UbO8gUJLsWsfF0Fk5KAcdm+4kb4jbI1H4Qk
 Vol9WNRZwEllyaiqScZN9RuVVuH0GPOZeEH1dtWK+uWi0lM=
 =ZlBf
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "Notable changes:

   - Support for split PMD page table lock on 64-bit Book3S (Power8/9).

   - Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
     live patching again.

   - Add support for patching barrier_nospec in copy_from_user() and
     syscall entry.

   - A couple of fixes for our data breakpoints on Book3S.

   - A series from Nick optimising TLB/mm handling with the Radix MMU.

   - Numerous small cleanups to squash sparse/gcc warnings from Mathieu
     Malaterre.

   - Several series optimising various parts of the 32-bit code from
     Christophe Leroy.

   - Removal of support for two old machines, "SBC834xE" and "C2K"
     ("GEFanuc,C2K"), which is why the diffstat has so many deletions.

  And many other small improvements & fixes.

  There's a few out-of-area changes. Some minor ftrace changes OK'ed by
  Steve, and a fix to our powernv cpuidle driver. Then there's a series
  touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
  around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
  been in next for several weeks.

  Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
  Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
  Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
  Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
  Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
  Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
  Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
  Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
  Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
  Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
  Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
  Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
  Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
  Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"

* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
  powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
  cpuidle: powernv: Fix promotion from snooze if next state disabled
  powerpc: fix build failure by disabling attribute-alias warning in pci_32
  ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
  powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
  powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
  powerpc/pkeys: Detach execute_only key on !PROT_EXEC
  powerpc/powernv: copy/paste - Mask SO bit in CR
  powerpc: Remove core support for Marvell mv64x60 hostbridges
  powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
  powerpc/boot: Remove support for Marvell mv64x60 i2c controller
  powerpc/boot: Remove support for Marvell MPSC serial controller
  powerpc/embedded6xx: Remove C2K board support
  powerpc/lib: optimise PPC32 memcmp
  powerpc/lib: optimise 32 bits __clear_user()
  powerpc/time: inline arch_vtime_task_switch()
  powerpc/Makefile: set -mcpu=860 flag for the 8xx
  powerpc: Implement csum_ipv6_magic in assembly
  powerpc/32: Optimise __csum_partial()
  powerpc/lib: Adjust .balign inside string functions for PPC32
  ...
2018-06-07 10:23:33 -07:00
Gautham R. Shenoy 0a4ec6aa03 cpuidle: powernv: Fix promotion from snooze if next state disabled
The commit 78eaa10f02 ("cpuidle: powernv/pseries: Auto-promotion of
snooze to deeper idle state") introduced a timeout for the snooze idle
state so that it could be eventually be promoted to a deeper idle
state. The snooze timeout value is static and set to the target
residency of the next idle state, which would train the cpuidle
governor to pick the next idle state eventually.

The unfortunate side-effect of this is that if the next idle state(s)
is disabled, the CPU will forever remain in snooze, despite the fact
that the system is completely idle, and other deeper idle states are
available.

This patch fixes the issue by dynamically setting the snooze timeout
to the target residency of the next enabled state on the device.

Before Patch:
  POWER8 : Only nap disabled.
  $ cpupower monitor sleep 30
  sleep took 30.01297 seconds and exited with status 0
                |Idle_Stats
  PKG |CORE|CPU | snoo | Nap  | Fast
     0|   8|   0| 96.41|  0.00|  0.00
     0|   8|   1| 96.43|  0.00|  0.00
     0|   8|   2| 96.47|  0.00|  0.00
     0|   8|   3| 96.35|  0.00|  0.00
     0|   8|   4| 96.37|  0.00|  0.00
     0|   8|   5| 96.37|  0.00|  0.00
     0|   8|   6| 96.47|  0.00|  0.00
     0|   8|   7| 96.47|  0.00|  0.00

  POWER9: Shallow states (stop0lite, stop1lite, stop2lite, stop0, stop1,
  stop2) disabled:
  $ cpupower monitor sleep 30
  sleep took 30.05033 seconds and exited with status 0
                |Idle_Stats
  PKG |CORE|CPU | snoo | stop | stop | stop | stop | stop | stop | stop | stop
     0|  16|   0| 89.79|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00
     0|  16|   1| 90.12|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00
     0|  16|   2| 90.21|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00
     0|  16|   3| 90.29|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00

After Patch:
  POWER8 : Only nap disabled.
  $ cpupower monitor sleep 30
  sleep took 30.01200 seconds and exited with status 0
                |Idle_Stats
  PKG |CORE|CPU | snoo | Nap  | Fast
     0|   8|   0| 16.58|  0.00| 77.21
     0|   8|   1| 18.42|  0.00| 75.38
     0|   8|   2|  4.70|  0.00| 94.09
     0|   8|   3| 17.06|  0.00| 81.73
     0|   8|   4|  3.06|  0.00| 95.73
     0|   8|   5|  7.00|  0.00| 96.80
     0|   8|   6|  1.00|  0.00| 98.79
     0|   8|   7|  5.62|  0.00| 94.17

  POWER9: Shallow states (stop0lite, stop1lite, stop2lite, stop0, stop1,
  stop2) disabled:

  $ cpupower monitor sleep 30
  sleep took 30.02110 seconds and exited with status 0
                |Idle_Stats
  PKG |CORE|CPU | snoo | stop | stop | stop | stop | stop | stop | stop | stop
     0|   0|   0|  0.69|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  9.39| 89.70
     0|   0|   1|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.05| 93.21
     0|   0|   2|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00| 89.93
     0|   0|   3|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00|  0.00| 93.26

Fixes: 78eaa10f02 ("cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2018-06-05 22:16:24 +10:00
Rafael J. Wysocki 0fc784fb09 cpuidle: governors: Consolidate PM QoS handling
There is some code duplication related to the PM QoS handling between
the existing cpuidle governors, so move that code to a common helper
function and call that from the governors.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-05-30 23:13:00 +02:00
Rafael J. Wysocki cf7eeea947 cpuidle: governors: Drop redundant checks related to PM QoS
PM_QOS_RESUME_LATENCY_NO_CONSTRAINT is defined as the 32-bit integer
maximum, so it is not necessary to test the return value of
dev_pm_qos_raw_read_value() against it directly in the menu and
ladder cpuidle governors.

Drop these redundant checks.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-05-30 23:13:00 +02:00
Rafael J. Wysocki 87c9fe6ee4 cpuidle: menu: Avoid selecting shallow states with stopped tick
If the scheduler tick has been stopped already and the governor
selects a shallow idle state, the CPU can spend a long time in that
state if the selection is based on an inaccurate prediction of idle
time.  That effect turns out to be relevant, so it needs to be
mitigated.

To that end, modify the menu governor to discard the result of the
idle time prediction if the tick is stopped and the predicted idle
time is less than the tick period length, unless the tick timer is
going to expire soon.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2018-04-09 11:54:57 +02:00
Rafael J. Wysocki 296bb1e51a cpuidle: menu: Refine idle state selection for running tick
If the tick isn't stopped, the target residency of the state selected
by the menu governor may be greater than the actual time to the next
tick and that means lost energy.

To avoid that, make tick_nohz_get_sleep_length() return the current
time to the next event (before stopping the tick) in addition to the
estimated one via an extra pointer argument and make menu_select()
use that value to refine the state selection when necessary.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2018-04-09 11:54:56 +02:00
Rafael J. Wysocki 45f1ff59e2 cpuidle: Return nohz hint from cpuidle_select()
Add a new pointer argument to cpuidle_select() and to the ->select
cpuidle governor callback to allow a boolean value indicating
whether or not the tick should be stopped before entering the
selected state to be returned from there.

Make the ladder governor ignore that pointer (to preserve its
current behavior) and make the menu governor return 'false" through
it if:
 (1) the idle exit latency is constrained at 0, or
 (2) the selected state is a polling one, or
 (3) the expected idle period duration is within the tick period
     range.

In addition to that, the correction factor computations in the menu
governor need to take the possibility that the tick may not be
stopped into account to avoid artificially small correction factor
values.  To that end, add a mechanism to record tick wakeups, as
suggested by Peter Zijlstra, and use it to modify the menu_update()
behavior when tick wakeup occurs.  Namely, if the CPU is woken up by
the tick and the return value of tick_nohz_get_sleep_length() is not
within the tick boundary, the predicted idle duration is likely too
short, so make menu_update() try to compensate for that by updating
the governor statistics as though the CPU was idle for a long time.

Since the value returned through the new argument pointer of
cpuidle_select() is not used by its caller yet, this change by
itself is not expected to alter the functionality of the code.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
2018-04-06 09:29:34 +02:00
Rafael J. Wysocki 4dc2375c1a cpuidle: poll_state: Avoid invoking local_clock() too often
Rik reports that he sees an increase in CPU use in one benchmark
due to commit 612f1a22f067 "cpuidle: poll_state: Add time limit to
poll_idle()" that caused poll_idle() to call local_clock() in every
iteration of the loop.  Utilization increase generally means more
non-idle time with respect to total CPU time (on the average) which
implies reduced CPU frequency.

Doug reports that limiting the rate of local_clock() invocations
in there causes much less power to be drawn during a CPU-intensive
parallel workload (with idle states 1 and 2 disabled to enforce more
state 0 residency).

These two reports together suggest that executing local_clock() on
multiple CPUs in parallel at a high rate may cause chips to get hot
and trigger thermal/power limits on them to kick in, so reduce the
rate of local_clock() invocations in poll_idle() to avoid that issue.

Fixes: 612f1a22f067 "cpuidle: poll_state: Add time limit to poll_idle()"
Reported-by: Rik van Riel <riel@surriel.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Rik van Riel <riel@surriel.com>
2018-03-29 13:06:08 +02:00
Rafael J. Wysocki 64bdff6980 PM: cpuidle/suspend: Add s2idle usage and time state attributes
Add a new attribute group called "s2idle" under the sysfs directory
of each cpuidle state that supports the ->enter_s2idle callback
and put two new attributes, "usage" and "time", into that group to
represent the number of times the given state was requested for
suspend-to-idle and the total time spent in suspend-to-idle after
requesting that state, respectively.

That will allow diagnostic information related to suspend-to-idle
to be collected without enabling advanced debug features and
analyzing dmesg output.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-03-29 13:06:08 +02:00
Marek Szyprowski 8919d779f1 cpuidle: Enable coupled cpuidle support on Exynos3250 platform
All the needed code has been already merged to mach-exynos core in
commit af9971144d ("ARM: EXYNOS: add coupled cpuidle support for
Exynos3250"), so enable support for coupled variant also for Exynos3250
SoCs.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-03-29 13:06:08 +02:00
Rafael J. Wysocki a37b969a61 cpuidle: poll_state: Add time limit to poll_idle()
If poll_idle() is allowed to spin until need_resched() returns 'true',
it may actually spin for a much longer time than expected by the idle
governor, since set_tsk_need_resched() is not always called by the
timer interrupt handler.  If that happens, the CPU may spend much
more time than anticipated in the "polling" state.

To prevent that from happening, limit the time of the spinning loop
in poll_idle().

Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
2018-03-29 13:06:07 +02:00
Markus Elfring bda4d21b6e ARM: cpuidle: Drop memory allocation error message from arm_idle_init_cpu()
Omit an extra message for a memory allocation failure in this function.

This issue was detected by using the Coccinelle software.

Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-03-05 12:39:32 +01:00
Linus Torvalds 03f51d4efa powerpc updates for 4.16
Highlights:
 
  - Enable support for memory protection keys aka "pkeys" on Power7/8/9 when
    using the hash table MMU.
 
  - Extend our interrupt soft masking to support masking PMU interrupts as well
    as "normal" interrupts, and then use that to implement local_t for a ~4x
    speedup vs the current atomics-based implementation.
 
  - A new driver "ocxl" for "Open Coherent Accelerator Processor Interface
    (OpenCAPI)" devices.
 
  - Support for new device tree properties on PowerVM to describe hotpluggable
    memory and devices.
 
  - Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit VDSO.
 
  - Freescale updates from Scott:
      "Contains fixes for CPM GPIO and an FSL PCI erratum workaround, plus a
       minor cleanup patch."
 
 As well as quite a lot of other changes all over the place, and small fixes and
 cleanups as always.
 
 Thanks to:
   Alan Modra, Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andreas
   Schwab, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Anshuman
   Khandual, Anton Blanchard, Arnd Bergmann, Balbir Singh, Benjamin
   Herrenschmidt, Bhaktipriya Shridhar, Bryant G. Ly, Cédric Le Goater,
   Christophe Leroy, Christophe Lombard, Cyril Bur, David Gibson, Desnes A. Nunes
   do Rosario, Dmitry Torokhov, Frederic Barrat, Geert Uytterhoeven, Guilherme G.
   Piccoli, Gustavo A. R. Silva, Gustavo Romero, Ivan Mikhaylov, Joakim
   Tjernlund, Joe Perches, Josh Poimboeuf, Juan J. Alvarez, Julia Cartwright,
   Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre,
   Michael Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
   Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud, Ram Pai,
   Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee, Simon Guo, Stewart
   Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann, Vaibhav Jain, Vasyl
   Gomonovych.
 -----BEGIN PGP SIGNATURE-----
 
 iQIwBAABCAAaBQJadF6wExxtcGVAZWxsZXJtYW4uaWQuYXUACgkQUevqPMjhpYA2
 nBAAnguCEyAIYpc+ffE3WU9xJEWxa6bKuVufHcUFVntGiGD+igmMS+SHp4ay3Aos
 HcA4WFrpzNb2KZ++kmFWtAKWnMfCiW9xuYJNicjr7X5ZiVBEhLWN/mQCwBKs3p6L
 5+HhvytcdkKVbEcyVjEGvRL40AyxXNOI02o6Co9X8vanHsmWB4q0eWe4PHstZqlg
 6K6kazMp+NTvEFYwKNXDOvuHouKSL57l14SLROH7CpJkNTOQ9s+W59/LmnuCjRlu
 o70b7iWOAEbF9tvMma1ksDZVNj7mSyaymLYCyOXu4CkuuleJacZYJ9oQGNddoIbC
 wk7l93vPT/yze7DYg8x3uXpKcaDEvEepPuQ/ubz+UXFQWuJtl5ej6Cv+0eOmyZIs
 +bjWhGHKdNttnsiPlTRCX/gWD13RE1dB6xXJlfOJ7Oz9OnXXK8ZKc1NTREbQXRWM
 8tClAwf9upWpm86GHPVnyrgYbgZo5b1os4SoS8e3kESzakrQVQP7J376u2DtccRq
 2AGqjJ+tl5tYPnhm8zG1cNrpqHHpgkNGqLS7DvWRg3EPmEKVQcltN1b/0aKaAjHA
 aTRofjrVo+jJ4MX1uyEo59yNCEQPfjkmHRQdLwm+xjWTzEPfIMzpWyXm14tawDQf
 OjcAe90W/qQ18brw4z+2BI14J76XziOSX/QcunOn1u/sqaM=
 =3rYn
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "Highlights:

   - Enable support for memory protection keys aka "pkeys" on Power7/8/9
     when using the hash table MMU.

   - Extend our interrupt soft masking to support masking PMU interrupts
     as well as "normal" interrupts, and then use that to implement
     local_t for a ~4x speedup vs the current atomics-based
     implementation.

   - A new driver "ocxl" for "Open Coherent Accelerator Processor
     Interface (OpenCAPI)" devices.

   - Support for new device tree properties on PowerVM to describe
     hotpluggable memory and devices.

   - Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 64-bit
     VDSO.

   - Freescale updates from Scott: fixes for CPM GPIO and an FSL PCI
     erratum workaround, plus a minor cleanup patch.

  As well as quite a lot of other changes all over the place, and small
  fixes and cleanups as always.

  Thanks to: Alan Modra, Alastair D'Silva, Alexey Kardashevskiy,
  Alistair Popple, Andreas Schwab, Andrew Donnellan, Aneesh Kumar K.V,
  Anju T Sudhakar, Anshuman Khandual, Anton Blanchard, Arnd Bergmann,
  Balbir Singh, Benjamin Herrenschmidt, Bhaktipriya Shridhar, Bryant G.
  Ly, Cédric Le Goater, Christophe Leroy, Christophe Lombard, Cyril Bur,
  David Gibson, Desnes A. Nunes do Rosario, Dmitry Torokhov, Frederic
  Barrat, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo A. R. Silva,
  Gustavo Romero, Ivan Mikhaylov, Joakim Tjernlund, Joe Perches, Josh
  Poimboeuf, Juan J. Alvarez, Julia Cartwright, Kamalesh Babulal,
  Madhavan Srinivasan, Mahesh Salgaonkar, Mathieu Malaterre, Michael
  Bringmann, Michael Hanselmann, Michael Neuling, Nathan Fontenot,
  Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Philippe Bergheaud,
  Ram Pai, Russell Currey, Santosh Sivaraj, Scott Wood, Seth Forshee,
  Simon Guo, Stewart Smith, Sukadev Bhattiprolu, Thiago Jung Bauermann,
  Vaibhav Jain, Vasyl Gomonovych"

* tag 'powerpc-4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (199 commits)
  powerpc/mm/radix: Fix build error when RADIX_MMU=n
  macintosh/ams-input: Use true and false for boolean values
  macintosh: change some data types from int to bool
  powerpc/watchdog: Print the NIP in soft_nmi_interrupt()
  powerpc/watchdog: regs can't be null in soft_nmi_interrupt()
  powerpc/watchdog: Tweak watchdog printks
  powerpc/cell: Remove axonram driver
  rtc-opal: Fix handling of firmware error codes, prevent busy loops
  powerpc/mpc52xx_gpt: make use of raw_spinlock variants
  macintosh/adb: Properly mark continued kernel messages
  powerpc/pseries: Fix cpu hotplug crash with memoryless nodes
  powerpc/numa: Ensure nodes initialized for hotplug
  powerpc/numa: Use ibm,max-associativity-domains to discover possible nodes
  powerpc/kernel: Block interrupts when updating TIDR
  powerpc/powernv/idoa: Remove unnecessary pcidev from pci_dn
  powerpc/mm/nohash: do not flush the entire mm when range is a single page
  powerpc/pseries: Add Initialization of VF Bars
  powerpc/pseries/pci: Associate PEs to VFs in configure SR-IOV
  powerpc/eeh: Add EEH notify resume sysfs
  powerpc/eeh: Add EEH operations to notify resume
  ...
2018-02-02 10:01:04 -08:00
Nicholas Piggin f2ac428e0e powerpc/pseries/cpuidle: add polling idle for shared processor guests
For shared processor guests (e.g., KVM), add an idle polling mode rather
than immediately returning to the hypervisor when the guest CPU goes
idle.

Test setup is a 2 socket POWER9 with 4 guests running, each with vCPUs
equal to 1/2 of real of CPUs. Saturated each guest with tbench. Using
polling idle gives about 1.4x throughput.

Kernel compile speed was not changed significantly.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2018-01-18 15:43:44 +11:00
Nicholas Piggin ced54c08d8 cpuidle/powernv: avoid double irq enable coming out of idle
Since e1689795a7 ("cpuidle: Add common time keeping and irq enabling"),
cpuidle drivers are expected to return from ->enter with irqs disabled.

Update the cpuidle-powernv snooze and cede loops to disable irqs before
returning.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2018-01-18 15:43:44 +11:00
Nicholas Piggin f1343d0446 cpuidle/powernv: avoid double irq enable coming out of idle
Since e1689795a7 ("cpuidle: Add common time keeping and irq enabling"),
cpuidle drivers are expected to return from ->enter with irqs disabled.

Update the cpuidle-powernv snooze loop to disable irqs before returning.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2018-01-18 15:43:43 +11:00
gaurav jindal 3cfd68b5ba cpuidle: Avoid NULL argument in cpuidle_switch_governor()
Checks if the new governor is NULL before updating the
cupidle_curr_governor.

Signed-off-by: gaurav jindal <gauravjindal1104@gmail.com>
[ rjw : Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2018-01-05 14:01:30 +01:00
Linus Torvalds 5b0e2cb020 powerpc updates for 4.15
Non-highlights:
 
  - Five fixes for the >128T address space handling, both to fix bugs in our
    implementation and to bring the semantics exactly into line with x86.
 
 Highlights:
 
  - Support for a new OPAL call on bare metal machines which gives us a true NMI
    (ie. is not masked by MSR[EE]=0) for debugging etc.
 
  - Support for Power9 DD2 in the CXL driver.
 
  - Improvements to machine check handling so that uncorrectable errors can be
    reported into the generic memory_failure() machinery.
 
  - Some fixes and improvements for VPHN, which is used under PowerVM to notify
    the Linux partition of topology changes.
 
  - Plumbing to enable TM (transactional memory) without suspend on some Power9
    processors (PPC_FEATURE2_HTM_NO_SUSPEND).
 
  - Support for emulating vector loads form cache-inhibited memory, on some
    Power9 revisions.
 
  - Disable the fast-endian switch "syscall" by default (behind a CONFIG), we
    believe it has never had any users.
 
  - A major rework of the API drivers use when initiating and waiting for long
    running operations performed by OPAL firmware, and changes to the
    powernv_flash driver to use the new API.
 
  - Several fixes for the handling of FP/VMX/VSX while processes are using
    transactional memory.
 
  - Optimisations of TLB range flushes when using the radix MMU on Power9.
 
  - Improvements to the VAS facility used to access coprocessors on Power9, and
    related improvements to the way the NX crypto driver handles requests.
 
  - Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
 
 Thanks to:
   Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh
   Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao,
   Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R.
   Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren
   Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami
   Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
   Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de
   Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen
   Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain,
   Vaidyanathan Srinivasan, William A. Kennington III.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJaDXGuAAoJEFHr6jzI4aWAEqwP/0TA35KFAK6wqfkCf67z4q+O
 I+5piI4eDV4jdCakfoIN1JfjhQRULNePSoCHTccan30mu/bm30p69xtOLL2/h5xH
 Mhz/eDBAOo0lrT20nyZfYMW3FnM66wnNf++qJ0O+8L052r4WOB02J0k1uM1ST01D
 5Lb5mUoxRLRzCgKRYAYWJifn+IFPUB9NMsvMTym94krAFlIjIzMEQXhDoln+jJMr
 QmY5f1BTA/fLfXobn0zwoc/C1oa2PUtxd+rxbwGrLoZ6G843mMqUi90SMr5ybhXp
 RzepnBTj4by3vOsnk/X1mANyaZfLsunp75FwnjHdPzKrAS/TuPp8D/iSxxE/PzEq
 cLwJFBnFXSgQMefDErXxhHSDz2dAg5r14rsTpDcq2Ko8TPV4rPsuSfmbd9Txekb0
 yWHsjoJUBBMl2QcWqIHl+AlV8j1RklF6solcTBcGnH1CZJMfa05VKXV7xGEvOHa0
 RJ+/xPyR9KjoB/SUp++9Vmx/M6SwQYFOJlr3Zpg9LNtR8WpoPYu1E6eO+u1Hhzny
 eJqaNstH+i+VdY9eqszkAsEBh8o9M/+b+7Wx7TetvU+v368CbXtgFYs9qy2oZjPF
 t9sY/BHaHZ8eZ7I00an77a0fVV5B1PVASUtIz5CqkwGpMvX6Z6W2K/XUUFI61kuu
 E06HS6Ht8UPJAzrAPUMl
 =Rq81
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "A bit of a small release, I suspect in part due to me travelling for
  KS. But my backlog of patches to review is smaller than usual, so I
  think in part folks just didn't send as much this cycle.

  Non-highlights:

   - Five fixes for the >128T address space handling, both to fix bugs
     in our implementation and to bring the semantics exactly into line
     with x86.

  Highlights:

   - Support for a new OPAL call on bare metal machines which gives us a
     true NMI (ie. is not masked by MSR[EE]=0) for debugging etc.

   - Support for Power9 DD2 in the CXL driver.

   - Improvements to machine check handling so that uncorrectable errors
     can be reported into the generic memory_failure() machinery.

   - Some fixes and improvements for VPHN, which is used under PowerVM
     to notify the Linux partition of topology changes.

   - Plumbing to enable TM (transactional memory) without suspend on
     some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND).

   - Support for emulating vector loads form cache-inhibited memory, on
     some Power9 revisions.

   - Disable the fast-endian switch "syscall" by default (behind a
     CONFIG), we believe it has never had any users.

   - A major rework of the API drivers use when initiating and waiting
     for long running operations performed by OPAL firmware, and changes
     to the powernv_flash driver to use the new API.

   - Several fixes for the handling of FP/VMX/VSX while processes are
     using transactional memory.

   - Optimisations of TLB range flushes when using the radix MMU on
     Power9.

   - Improvements to the VAS facility used to access coprocessors on
     Power9, and related improvements to the way the NX crypto driver
     handles requests.

   - Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.

  Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew
  Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin
  Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard,
  Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven,
  Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley,
  Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu,
  Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
  Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia
  Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee,
  Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel
  Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A.
  Kennington III"

* tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits)
  powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature
  powerpc/64s: Fix masking of SRR1 bits on instruction fault
  powerpc/64s: mm_context.addr_limit is only used on hash
  powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
  powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
  powerpc/64s/hash: Fix fork() with 512TB process address space
  powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
  powerpc/64s/hash: Fix 512T hint detection to use >= 128T
  powerpc: Fix DABR match on hash based systems
  powerpc/signal: Properly handle return value from uprobe_deny_signal()
  powerpc/fadump: use kstrtoint to handle sysfs store
  powerpc/lib: Implement UACCESS_FLUSHCACHE API
  powerpc/lib: Implement PMEM API
  powerpc/powernv/npu: Don't explicitly flush nmmu tlb
  powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm()
  powerpc/powernv/idle: Round up latency and residency values
  powerpc/kprobes: refactor kprobe_lookup_name for safer string operations
  powerpc/kprobes: Blacklist emulate_update_regs() from kprobes
  powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace
  powerpc/kprobes: Disable preemption before invoking probe handler for optprobes
  ...
2017-11-16 12:47:46 -08:00
Rafael J. Wysocki 622ade3a2f Merge branch 'pm-cpuidle'
* pm-cpuidle:
  intel_idle: Graceful probe failure when MWAIT is disabled
  cpuidle: Avoid assignment in if () argument
  cpuidle: Clean up cpuidle_enable_device() error handling a bit
  cpuidle: ladder: Add per CPU PM QoS resume latency support
  ARM: cpuidle: Refactor rollback operations if init fails
  ARM: cpuidle: Correct driver unregistration if init fails
  intel_idle: replace conditionals with static_cpu_has(X86_FEATURE_ARAT)
  cpuidle: fix broadcast control when broadcast can not be entered

 Conflicts:
	drivers/idle/intel_idle.c
2017-11-13 01:34:14 +01:00
Rafael J. Wysocki 4762573b93 Merge branch 'pm-qos'
* pm-qos:
  PM / QoS: Fix device resume latency framework
  PM / QoS: Drop PM_QOS_FLAG_REMOTE_WAKEUP
2017-11-13 01:33:48 +01:00
Vaidyanathan Srinivasan 8d4e10e9ed powerpc/powernv/idle: Round up latency and residency values
On PowerNV platforms, firmware provides exit latency and
target residency for each of the idle states in nano
seconds.  Cpuidle framework expects the values in micro
seconds.  Round up to nearest micro seconds to avoid errors
in cases where the values are defined as fractional micro
seconds.

Default idle state of 'snooze' has exit latency of zero.  If
other states have fractional micro second exit latency, they
would get rounded down to zero micro second and make cpuidle
framework choose deeper idle state when snooze loop is the
right choice.

Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-11-13 08:00:29 +11:00
Gaurav Jindal 3fc74bd8a7 cpuidle: Avoid assignment in if () argument
Clean up cpuidle_enable_device() to avoid doing an assignment
in an expression evaluated as an argument of if (), which also
makes the code in question more readable.

Signed-off-by: Gaurav Jindal <gauravjindal1104@gmail.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-11-08 23:15:30 +01:00
Gaurav Jindal e7b06a09e7 cpuidle: Clean up cpuidle_enable_device() error handling a bit
Do not fetch per CPU drv if cpuidle_curr_governor is NULL
to avoid useless per CPU processing.

Signed-off-by: Gaurav Jindal <gauravjindal1104@gmail.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-11-08 23:09:52 +01:00
Ramesh Thomas c523c68da2 cpuidle: ladder: Add per CPU PM QoS resume latency support
Individual CPUs may have special requirements to not enter
deep idle states. For example, a CPU running real time
applications would not want to enter deep idle states to
avoid latency impacts. At the same time other CPUs that
do not have such a requirement could allow deep idle
states to save power.

This was already implemented in the menu governor.
Implementing similar changes in the ladder governor which
gets selected when CONFIG_NO_HZ and CONFIG_NO_HZ_IDLE are not
set. Refer following commits for the menu governor changes.

Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-11-08 12:16:01 +01:00
Rafael J. Wysocki 4e37fd4d5d Merge branch 'pm-qos' into pm-cpuidle 2017-11-08 12:15:50 +01:00
Rafael J. Wysocki 0759e80b84 PM / QoS: Fix device resume latency framework
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.

First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value.  However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.

Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.

To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.

Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.

Fixes: 85dc0b8a40 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Ramesh Thomas <ramesh.thomas@intel.com>
2017-11-08 12:14:51 +01:00
Paul Burton fb615d61b5 Update MIPS email addresses
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:

 - Have 10 or more patches in mainline authored using an @imgtec.com
   email address, or any patches dated within the past year.

 - Are still with Imagination but leaving as part of the MIPS business
   unit, as determined from an internal email address list.

 - Haven't already updated their email address (ie. JamesH) or expressed
   a desire to be excluded (ie. Maciej).

 - Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
   myself.

New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list.  An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.

Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.

Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-11-03 09:02:30 -07:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Leo Yan 7943bfaeb6 ARM: cpuidle: Refactor rollback operations if init fails
If init fails, we need execute two levels rollback operations: the first
level is for the failed CPU rollback operations, the second level is to
iterate all succeeded CPUs to cancel their registration; currently the
code uses one function to finish these two levels rollback operations.

This commit is to refactor rollback operations, so it adds a new
function arm_idle_init_cpu() to encapsulate one specified CPU driver
registration and rollback the first level operations; and use function
arm_idle_init() to iterate all CPUs and finish the second level's
rollback operations.

Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-10-14 01:01:11 +02:00
Leo Yan 0f87855d96 ARM: cpuidle: Correct driver unregistration if init fails
If cpuidle init fails, the code misses to unregister the driver for
current CPU. Furthermore, we also need to rollback to cancel all
previous CPUs registration; but the code retrieves driver handler by
using function cpuidle_get_driver(), this function returns back
current CPU driver handler but not previous CPU's handler, which leads
to the failure handling code cannot unregister previous CPUs driver.

This commit fixes two mentioned issues, it adds error handling path
'goto out_unregister_drv' for current CPU driver unregistration; and
it is to replace cpuidle_get_driver() with cpuidle_get_cpu_driver(),
the later function can retrieve driver handler for previous CPUs
according to the CPU device handler so can unregister the driver
properly.

This patch also adds extra error handling paths 'goto out_kfree_dev'
and 'goto out_kfree_drv' and adjusts the freeing sentences for previous
CPUs; so make the code more readable for freeing 'dev' and 'drv'
structures.

Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Fixes: d50a7d8acd (ARM: cpuidle: Support asymmetric idle definition)
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-10-14 01:00:18 +02:00
Nicholas Piggin f187851b9b cpuidle: fix broadcast control when broadcast can not be entered
When failing to enter broadcast timer mode for an idle state that
requires it, a new state is selected that does not require broadcast,
but the broadcast variable remains set. This causes
tick_broadcast_exit to be called despite not having entered broadcast
mode.

This causes the WARN_ON_ONCE(!irqs_disabled()) to trigger in some
cases. It does not appear to cause problems for code today, but seems
to violate the interface so should be fixed.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-09-28 02:18:07 +02:00
Stefan Wahren ed40fad9a5 ARM: cpuidle: Avoid memleak if init fail
In case there are no DT idle states defined or
cpuidle_register_driver() fails, the copy of the idle driver is leaked:

    unreferenced object 0xede0dc00 (size 1024):
    comm "swapper/0", pid 1, jiffies 4294937431 (age 744.510s)
    hex dump (first 32 bytes):
    94 9e 0b c1 00 00 00 00 00 00 00 00 00 00 00 00 ................
    57 46 49 00 00 00 00 00 00 00 00 00 00 00 00 00 WFI.............
    backtrace:
    [<c1295f04>] arm_idle_init+0x44/0x1ac
    [<c0301e6c>] do_one_initcall+0x3c/0x16c
    [<c1200d70>] kernel_init_freeable+0x110/0x1d0
    [<c0cb3624>] kernel_init+0x8/0x114
    [<c0307a98>] ret_from_fork+0x14/0x3c

So fix this by freeing the unregistered copy in error case.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: d50a7d8acd (ARM: cpuidle: Support asymmetric idle definition)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-09-19 23:10:51 +02:00
Linus Torvalds 7318413077 Merge branch '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "This is the main pull request for 4.14 for MIPS; below a summary of
  the non-merge commits:

  CM:
   - Rename mips_cm_base to mips_gcr_base
   - Specify register size when generating accessors
   - Use BIT/GENMASK for register fields, order & drop shifts
   - Add cluster & block args to mips_cm_lock_other()

  CPC:
   - Use common CPS accessor generation macros
   - Use BIT/GENMASK for register fields, order & drop shifts
   - Introduce register modify (set/clear/change) accessors
   - Use change_*, set_* & clear_* where appropriate
   - Add CM/CPC 3.5 register definitions
   - Use GlobalNumber macros rather than magic numbers
   - Have asm/mips-cps.h include CM & CPC headers
   - Cluster support for topology functions
   - Detect CPUs in secondary clusters

  CPS:
   - Read GIC_VL_IDENT directly, not via irqchip driver

  DMA:
   - Consolidate coherent and non-coherent dma_alloc code
   - Don't use dma_cache_sync to implement fd_cacheflush

  FPU emulation / FP assist code:
   - Another series of 14 commits fixing corner cases such as NaN
     propgagation and other special input values.
   - Zero bits 32-63 of the result for a CLASS.D instruction.
   - Enhanced statics via debugfs
   - Do not use bools for arithmetic. GCC 7.1 moans about this.
   - Correct user fault_addr type

  Generic MIPS:
   - Enhancement of stack backtraces
   - Cleanup from non-existing options
   - Handle non word sized instructions when examining frame
   - Fix detection and decoding of ADDIUSP instruction
   - Fix decoding of SWSP16 instruction
   - Refactor handling of stack pointer in get_frame_info
   - Remove unreachable code from force_fcr31_sig()
   - Convert to using %pOF instead of full_name
   - Remove the R6000 support.
   - Move FP code from *_switch.S to *_fpu.S
   - Remove unused ST_OFF from r2300_switch.S
   - Allow platform to specify multiple its.S files
   - Add #includes to various files to ensure code builds reliable and
     without warning..
   - Remove __invalidate_kernel_vmap_range
   - Remove plat_timer_setup
   - Declare various variables & functions static
   - Abstract CPU core & VP(E) ID access through accessor functions
   - Store core & VP IDs in GlobalNumber-style variable
   - Unify checks for sibling CPUs
   - Add CPU cluster number accessors
   - Prevent direct use of generic_defconfig
   - Make CONFIG_MIPS_MT_SMP default y
   - Add __ioread64_copy
   - Remove unnecessary inclusions of linux/irqchip/mips-gic.h

  GIC:
   - Introduce asm/mips-gic.h with accessor functions
   - Use new GIC accessor functions in mips-gic-timer
   - Remove counter access functions from irq-mips-gic.c
   - Remove gic_read_local_vp_id() from irq-mips-gic.c
   - Simplify shared interrupt pending/mask reads in irq-mips-gic.c
   - Simplify gic_local_irq_domain_map() in irq-mips-gic.c
   - Drop gic_(re)set_mask() functions in irq-mips-gic.c
   - Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
     gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
   - Convert remaining shared reg access, local int mask access and
     remaining local reg access to new accessors
   - Move GIC_LOCAL_INT_* to asm/mips-gic.h
   - Remove GIC_CPU_INT* macros from irq-mips-gic.c
   - Move various definitions to the driver
   - Remove gic_get_usm_range()
   - Remove __gic_irq_dispatch() forward declaration
   - Remove gic_init()
   - Use mips_gic_present() in place of gic_present and remove
     gic_present
   - Move gic_get_c0_*_int() to asm/mips-gic.h
   - Remove linux/irqchip/mips-gic.h
   - Inline __gic_init()
   - Inline gic_basic_init()
   - Make pcpu_masks a per-cpu variable
   - Use pcpu_masks to avoid reading GIC_SH_MASK*
   - Clean up mti, reserved-cpu-vectors handling
   - Use cpumask_first_and() in gic_set_affinity()
   - Let the core set struct irq_common_data affinity

  microMIPS:
   - Fix microMIPS stack unwinding on big endian systems

  MIPS-GIC:
   - SYNC after enabling GIC region

  NUMA:
   - Remove the unused parent_node() macro

  R6:
   - Constify r2_decoder_tables
   - Add accessor & bit definitions for GlobalNumber

  SMP:
   - Constify smp ops
   - Allow boot_secondary SMP op to return errors

  VDSO:
   - Drop gic_get_usm_range() usage
   - Avoid use of linux/irqchip/mips-gic.h

  Platform changes:

  Alchemy:
   - Add devboard machine type to cpuinfo
   - update cpu feature overrides
   - Threaded carddetect irqs for devboards

  AR7:
   - allow NULL clock for clk_get_rate

  BCM63xx:
   - Fix ENETDMA_6345_MAXBURST_REG offset
   - Allow NULL clock for clk_get_rate

  CI20:
   - Enable GPIO and RTC drivers in defconfig
   - Add ethernet and fixed-regulator nodes to DTS

  Generic platform:
   - Move Boston and NI 169445 FIT image source to their own files
   - Include asm/bootinfo.h for plat_fdt_relocated()
   - Include asm/time.h for get_c0_*_int()
   - Include asm/bootinfo.h for plat_fdt_relocated()
   - Include asm/time.h for get_c0_*_int()
   - Allow filtering enabled boards by requirements
   - Don't explicitly disable CONFIG_USB_SUPPORT
   - Bump default NR_CPUS to 16

  JZ4700:
   - Probe the jz4740-rtc driver from devicetree

  Lantiq:
   - Drop check of boot select from the spi-falcon driver.
   - Drop check of boot select from the lantiq-flash MTD driver.
   - Access boot cause register in the watchdog driver through regmap
   - Add device tree binding documentation for the watchdog driver
   - Add docs for the RCU DT bindings.
   - Convert the fpi bus driver to a platform_driver
   - Remove ltq_reset_cause() and ltq_boot_select(
   - Switch to a proper reset driver
   - Switch to a new drivers/soc GPHY driver
   - Add an USB PHY driver for the Lantiq SoCs using the RCU module
   - Use of_platform_default_populate instead of __dt_register_buses
   - Enable MFD_SYSCON to be able to use it for the RCU MFD
   - Replace ltq_boot_select() with dummy implementation.

  Loongson 2F:
   - Allow NULL clock for clk_get_rate

  Malta:
   - Use new GIC accessor functions

  NI 169445:
   - Add support for NI 169445 board.
   - Only include in 32r2el kernels

  Octeon:
   - Add support for watchdog of 78XX SOCs.
   - Add support for watchdog of CN68XX SOCs.
   - Expose support for mips32r1, mips32r2 and mips64r1
   - Enable more drivers in config file
   - Add support for accessing the boot vector.
   - Remove old boot vector code from watchdog driver
   - Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
   - Make CSR functions node aware.
   - Allow access to CIU3 IRQ domains.
   - Misc cleanups in the watchdog driver

  Omega2+:
   - New board, add support and defconfig

  Pistachio:
   - Enable Root FS on NFS in defconfig

  Ralink:
   - Add Mediatek MT7628A SoC
   - Allow NULL clock for clk_get_rate
   - Explicitly request exclusive reset control in the pci-mt7620 PCI driver.

  SEAD3:
   - Only include in 32 bit kernels by default

  VoCore:
   - Add VoCore as a vendor t0 dt-bindings
   - Add defconfig file"

* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
  MIPS: Refactor handling of stack pointer in get_frame_info
  MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
  MIPS: microMIPS: Fix decoding of swsp16 instruction
  MIPS: microMIPS: Fix decoding of addiusp instruction
  MIPS: microMIPS: Fix detection of addiusp instruction
  MIPS: Handle non word sized instructions when examining frame
  MIPS: ralink: allow NULL clock for clk_get_rate
  MIPS: Loongson 2F: allow NULL clock for clk_get_rate
  MIPS: BCM63XX: allow NULL clock for clk_get_rate
  MIPS: AR7: allow NULL clock for clk_get_rate
  MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
  mips: Save all registers when saving the frame
  MIPS: Add DWARF unwinding to assembly
  MIPS: Make SAVE_SOME more standard
  MIPS: Fix issues in backtraces
  MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
  MIPS: Ci20: Enable RTC driver
  watchdog: octeon-wdt: Add support for 78XX SOCs.
  watchdog: octeon-wdt: Add support for cn68XX SOCs.
  watchdog: octeon-wdt: File cleaning.
  ...
2017-09-15 20:43:33 -07:00
Linus Torvalds 439644096c Power management updates for v4.14-rc1
- Drop the P-state selection algorithm based on a PID controller
    from intel_pstate and make it use the same P-state selection
    method (based on the CPU load) for all types of systems in the
    active mode (Rafael Wysocki, Srinivas Pandruvada).
 
  - Rework the cpufreq core and governors to make it possible to
    take cross-CPU utilization updates into account and modify the
    schedutil governor to actually do so (Viresh Kumar).
 
  - Clean up the handling of transition latency information in the
    cpufreq core and untangle it from the information on which drivers
    cannot do dynamic frequency switching (Viresh Kumar).
 
  - Add support for new SoCs (MT2701/MT7623 and MT7622) to the
    mediatek cpufreq driver and update its DT bindings (Sean Wang).
 
  - Modify the cpufreq dt-platdev driver to autimatically create
    cpufreq devices for the new (v2) Operating Performance Points
    (OPP) DT bindings and update its whitelist of supported systems
    (Viresh Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen,
    Finley Xiao).
 
  - Add support for Ux500 to the cpufreq-dt driver and drop the
    obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
 
  - Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
    Nguyen).
 
  - Fix and clean up assorted issues in the cpufreq drivers and core
    (Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
    Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
 
  - Update the IO-wait boost handling in the schedutil governor to
    make it less aggressive (Joel Fernandes).
 
  - Rework system suspend diagnostics to make it print fewer messages
    to the kernel log by default, add a sysfs knob to allow more
    suspend-related messages to be printed and add Low Power S0 Idle
    constraints checks to the ACPI suspend-to-idle code (Rafael
    Wysocki, Srinivas Pandruvada).
 
  - Prefer suspend-to-idle over S3 on ACPI-based systems with the
    ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
    interface present in the ACPI tables (Rafael Wysocki).
 
  - Update documentation related to system sleep and rename a number
    of items in the code to make it cleare that they are related to
    suspend-to-idle (Rafael Wysocki).
 
  - Export a variable allowing device drivers to check the target
    system sleep state from the core system suspend code (Florian
    Fainelli).
 
  - Clean up the cpuidle subsystem to handle the polling state on
    x86 in a more straightforward way and to use %pOF instead of
    full_name (Rafael Wysocki, Rob Herring).
 
  - Update the devfreq framework to fix and clean up a few minor
    issues (Chanwoo Choi, Rob Herring).
 
  - Extend diagnostics in the generic power domains (genpd) framework
    and clean it up slightly (Thara Gopinath, Rob Herring).
 
  - Fix and clean up a couple of issues in the operating performance
    points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
 
  - Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
    (AVS) driver (David Wu).
 
  - Fix the usage of notifiers in CPU power management on some
    platforms (Alex Shi).
 
  - Update the pm-graph system suspend/hibernation and boot profiling
    utility (Todd Brandt).
 
  - Make it possible to run the cpupower utility without CPU0 (Prarit
    Bhargava).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZrcDJAAoJEILEb/54YlRx9FUQAIUKvWBAARc61ZIZXjbqZF1v
 aEMOBuksFns0CMekdptSic6n4wc81E/XYMS8yDhOOMpyDzfAZsTWjmu+gKwN7w3l
 E/yf/NVlhob9JZ7MqGgqD4EUFfFIaKBXPlWFdDi2rdCUXE2L8xJ7rla8i7zyZlc5
 pYHfAppBbF4qUcEY4OoOVOOGRZCfMdiLXj0iZOhMX8Y6yLBRk/AjnVADYsF33hoj
 gBEfomU+H0K5V8nQEp0ZFKDArPwL+oElHQj6i+nxBpGfPM5evvLXhHOyR6AsldJ5
 J4YI1kMuQNSCmvHMqOTxTYyJf8Jcf3Fj4wcjwaVMVGceY1lz6McAKknnFnCqCvz+
 mskn84gFCBCM8EoJDqRf0b9MQHcuRyQKM+yw4tjnR9r8yd32erb85ZWFHcPWYhCT
 fZatNOwFFv2MU+2vo5J3yeUNSWIKT+uBjy+tKPbrDkUwpKZVRj3Oj+hP3Mq9NE8U
 YBqltsj7tmrdA634zI8C7jfS6wF221S0fId/iPszwmPJaVn/lq8Ror7pWL5YI8U7
 SCJFjiqDiGmAcQEkuWwFAQnscZkyHpO+Y3A+jfXl/izoaZETaI5+ceIHBaocm3+5
 XrOOpHS3ik8EHf9ji0KFCKZ/pYDwllday3cBQPWo3sMIzpQ2lrjbqdnE1cVnBrld
 OtHZAeD/jLUXuY6XW2jN
 =mAiV
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "This time (again) cpufreq gets the majority of changes which mostly
  are driver updates (including a major consolidation of intel_pstate),
  some schedutil governor modifications and core cleanups.

  There also are some changes in the system suspend area, mostly related
  to diagnostics and debug messages plus some renames of things related
  to suspend-to-idle. One major change here is that suspend-to-idle is
  now going to be preferred over S3 on systems where the ACPI tables
  indicate to do so and provide requsite support (the Low Power Idle S0
  _DSM in particular). The system sleep documentation and the tools
  related to it are updated too.

  The rest is a few cpuidle changes (nothing major), devfreq updates,
  generic power domains (genpd) framework updates and a few assorted
  modifications elsewhere.

  Specifics:

   - Drop the P-state selection algorithm based on a PID controller from
     intel_pstate and make it use the same P-state selection method
     (based on the CPU load) for all types of systems in the active mode
     (Rafael Wysocki, Srinivas Pandruvada).

   - Rework the cpufreq core and governors to make it possible to take
     cross-CPU utilization updates into account and modify the schedutil
     governor to actually do so (Viresh Kumar).

   - Clean up the handling of transition latency information in the
     cpufreq core and untangle it from the information on which drivers
     cannot do dynamic frequency switching (Viresh Kumar).

   - Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
     cpufreq driver and update its DT bindings (Sean Wang).

   - Modify the cpufreq dt-platdev driver to autimatically create
     cpufreq devices for the new (v2) Operating Performance Points (OPP)
     DT bindings and update its whitelist of supported systems (Viresh
     Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
     Xiao).

   - Add support for Ux500 to the cpufreq-dt driver and drop the
     obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).

   - Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
     Nguyen).

   - Fix and clean up assorted issues in the cpufreq drivers and core
     (Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
     Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).

   - Update the IO-wait boost handling in the schedutil governor to make
     it less aggressive (Joel Fernandes).

   - Rework system suspend diagnostics to make it print fewer messages
     to the kernel log by default, add a sysfs knob to allow more
     suspend-related messages to be printed and add Low Power S0 Idle
     constraints checks to the ACPI suspend-to-idle code (Rafael
     Wysocki, Srinivas Pandruvada).

   - Prefer suspend-to-idle over S3 on ACPI-based systems with the
     ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
     interface present in the ACPI tables (Rafael Wysocki).

   - Update documentation related to system sleep and rename a number of
     items in the code to make it cleare that they are related to
     suspend-to-idle (Rafael Wysocki).

   - Export a variable allowing device drivers to check the target
     system sleep state from the core system suspend code (Florian
     Fainelli).

   - Clean up the cpuidle subsystem to handle the polling state on x86
     in a more straightforward way and to use %pOF instead of full_name
     (Rafael Wysocki, Rob Herring).

   - Update the devfreq framework to fix and clean up a few minor issues
     (Chanwoo Choi, Rob Herring).

   - Extend diagnostics in the generic power domains (genpd) framework
     and clean it up slightly (Thara Gopinath, Rob Herring).

   - Fix and clean up a couple of issues in the operating performance
     points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).

   - Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
     (AVS) driver (David Wu).

   - Fix the usage of notifiers in CPU power management on some
     platforms (Alex Shi).

   - Update the pm-graph system suspend/hibernation and boot profiling
     utility (Todd Brandt).

   - Make it possible to run the cpupower utility without CPU0 (Prarit
     Bhargava)"

* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
  cpuidle: Make drivers initialize polling state
  cpuidle: Move polling state initialization code to separate file
  cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
  cpufreq: imx6q: Fix imx6sx low frequency support
  cpufreq: speedstep-lib: make several arrays static, makes code smaller
  PM: docs: Delete the obsolete states.txt document
  PM: docs: Describe high-level PM strategies and sleep states
  PM / devfreq: Fix memory leak when fail to register device
  PM / devfreq: Add dependency on PM_OPP
  PM / devfreq: Move private devfreq_update_stats() into devfreq
  PM / devfreq: Convert to using %pOF instead of full_name
  PM / AVS: rockchip-io: add io selectors and supplies for RV1108
  cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
  cpufreq: dt-platdev: Drop few entries from whitelist
  cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
  ARM: ux500: don't select CPUFREQ_DT
  cpuidle: Convert to using %pOF instead of full_name
  cpufreq: Convert to using %pOF instead of full_name
  PM / Domains: Convert to using %pOF instead of full_name
  cpufreq: Cap the default transition delay value to 10 ms
  ...
2017-09-05 12:19:08 -07:00
Rafael J. Wysocki 7b01463e51 Merge branch 'pm-sleep'
* pm-sleep:
  ACPI / PM: Check low power idle constraints for debug only
  PM / s2idle: Rename platform operations structure
  PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
  PM / s2idle: Rename freeze_state enum and related items
  PM / s2idle: Rename PM_SUSPEND_FREEZE to PM_SUSPEND_TO_IDLE
  ACPI / PM: Prefer suspend-to-idle over S3 on some systems
  platform/x86: intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle
  PM / suspend: Define pr_fmt() in suspend.c
  PM / suspend: Use mem_sleep_labels[] strings in messages
  PM / sleep: Put pm_test under CONFIG_PM_SLEEP_DEBUG
  PM / sleep: Check pm_wakeup_pending() in __device_suspend_noirq()
  PM / core: Add error argument to dpm_show_time()
  PM / core: Split dpm_suspend_noirq() and dpm_resume_noirq()
  PM / s2idle: Rearrange the main suspend-to-idle loop
  PM / timekeeping: Print debug messages when requested
  PM / sleep: Mark suspend/hibernation start and finish
  PM / sleep: Do not print debug messages by default
  PM / suspend: Export pm_suspend_target_state
2017-09-04 00:06:02 +02:00
Rafael J. Wysocki 1b39e3f813 cpuidle: Make drivers initialize polling state
Make the drivers that want to include the polling state into their
states table initialize it explicitly and drop the initialization of
it (which in fact is conditional, but that is not obvious from the
code) from the core.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2017-08-30 03:06:33 +02:00
Rafael J. Wysocki 34c2f65b71 cpuidle: Move polling state initialization code to separate file
Move the polling state initialization code to a separate file built
conditionally on CONFIG_ARCH_HAS_CPU_RELAX to get rid of the #ifdef
in driver.c.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2017-08-30 03:06:27 +02:00
Rafael J. Wysocki dc2251bf98 cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
On some architectures the first (index 0) idle state is a polling
one and it doesn't really save energy, so there is the
CPUIDLE_DRIVER_STATE_START symbol allowing some pieces of
cpuidle code to avoid using that state.

However, this makes the code rather hard to follow.  It is better
to explicitly avoid the polling state, so add a new cpuidle state
flag CPUIDLE_FLAG_POLLING to mark it and make the relevant code
check that flag for the first state instead of using the
CPUIDLE_DRIVER_STATE_START symbol.

In the ACPI processor driver that cannot always rely on the state
flags (like before the states table has been set up) define
a new internal symbol ACPI_IDLE_STATE_START equivalent to the
CPUIDLE_DRIVER_STATE_START one and drop the latter.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
2017-08-30 03:05:29 +02:00
Paul Burton fe7a38c625 MIPS: Unify checks for sibling CPUs
Up until now we have open-coded checks for whether CPUs are siblings,
with slight variations on whether we consider the package ID or not.

This will only get more complex when we introduce cluster support, so in
preparation for that this patch introduces a cpus_are_siblings()
function which can be used to check whether or not 2 CPUs are siblings
in a consistent manner.

By checking globalnumber with the VP ID masked out this also has the
neat side effect of being ready for multi-cluster systems already.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30 00:57:27 +02:00
Paul Burton f875a832d2 MIPS: Abstract CPU core & VP(E) ID access through accessor functions
We currently have fields in struct cpuinfo_mips for the core & VP(E) ID
of a particular CPU, and various pieces of code directly access those
fields. This patch abstracts such access by introducing accessor
functions cpu_core(), cpu_set_core(), cpu_vpe_id() & cpu_set_vpe_id()
and having code that needs to access these values call those functions
rather than directly accessing the struct cpuinfo_mips fields. This
prepares us for changes to the way in which those values are stored in
later patches.

The cpu_vpe_id() function is introduced even though we already had a
cpu_vpe_id() macro for a couple of reasons:

  1) It's more consistent with the core, and future cluster, accessors.

  2) It ensures a sensible return type without explicit casts.

  3) It's generally preferable to use functions rather than macros.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2017-08-30 00:57:26 +02:00
Ying Huang 966a967116 smp: Avoid using two cache lines for struct call_single_data
struct call_single_data is used in IPIs to transfer information between
CPUs.  Its size is bigger than sizeof(unsigned long) and less than
cache line size.  Currently it is not allocated with any explicit alignment
requirements.  This makes it possible for allocated call_single_data to
cross two cache lines, which results in double the number of the cache lines
that need to be transferred among CPUs.

This can be fixed by requiring call_single_data to be aligned with the
size of call_single_data. Currently the size of call_single_data is the
power of 2.  If we add new fields to call_single_data, we may need to
add padding to make sure the size of new definition is the power of 2
as well.

Fortunately, this is enforced by GCC, which will report bad sizes.

To set alignment requirements of call_single_data to the size of
call_single_data, a struct definition and a typedef is used.

To test the effect of the patch, I used the vm-scalability multiple
thread swap test case (swap-w-seq-mt).  The test will create multiple
threads and each thread will eat memory until all RAM and part of swap
is used, so that huge number of IPIs are triggered when unmapping
memory.  In the test, the throughput of memory writing improves ~5%
compared with misaligned call_single_data, because of faster IPIs.

Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[ Add call_single_data_t and align with size of call_single_data. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/87bmnqd6lz.fsf@yhuang-mobile.sh.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-08-29 15:14:38 +02:00
Rob Herring 84dc4141f0 cpuidle: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-25 01:29:55 +02:00
Rafael J. Wysocki 28ba086ed3 PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
Rename the ->enter_freeze cpuidle driver callback to ->enter_s2idle
to make it clear that it is used for entering suspend-to-idle and
rename the related functions, variables and so on accordingly.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-08-11 01:29:56 +02:00
Gautham R. Shenoy 785a12afdb powerpc/powernv/idle: Disable LOSE_FULL_CONTEXT states when stop-api fails
Currently, we use the opal call opal_slw_set_reg() to inform the
Sleep-Winkle Engine (SLW) to restore the contents of some of the
Hypervisor state on wakeup from deep idle states that lose full
hypervisor context (characterized by the flag
OPAL_PM_LOSE_FULL_CONTEXT).

However, the current code has a bug in that if opal_slw_set_reg()
fails, we don't disable the use of these deep states (winkle on
POWER8, stop4 onwards on POWER9).

This patch fixes this bug by ensuring that if programing the
sleep-winkle engine to restore the hypervisor states in
pnv_save_sprs_for_deep_states() fails, then we exclude such states by
clearing the OPAL_PM_LOSE_FULL_CONTEXT flag from
supported_cpuidle_states. As a result POWER8 will be prevented from
using winkle for CPU-Hotplug, and POWER9 will put the offlined CPUs to
the default stop state when available.

Further, we ensure in the initialization of the cpuidle-powernv driver
to only include those states whose flags are present in
supported_cpuidle_states, thereby skipping OPAL_PM_LOSE_FULL_CONTEXT
states when they have been disabled due to stop-api failure.

Fixes: 1e1601b38e ("powerpc/powernv/idle: Restore SPRs for deep idle
states via stop API.")

Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-08-08 20:21:23 +10:00
Linus Torvalds d691b7e7d1 powerpc updates for 4.13
Highlights include:
 
  - Support for STRICT_KERNEL_RWX on 64-bit server CPUs.
 
  - Platform support for FSP2 (476fpe) board
 
  - Enable ZONE_DEVICE on 64-bit server CPUs.
 
  - Generic & powerpc spin loop primitives to optimise busy waiting
 
  - Convert VDSO update function to use new update_vsyscall() interface
 
  - Optimisations to hypercall/syscall/context-switch paths
 
  - Improvements to the CPU idle code on Power8 and Power9.
 
 As well as many other fixes and improvements.
 
 Thanks to:
   Akshay Adiga, Andrew Donnellan, Andrew Jeffery, Anshuman Khandual, Anton
   Blanchard, Balbir Singh, Benjamin Herrenschmidt, Christophe Leroy, Christophe
   Lombard, Colin Ian King, Dan Carpenter, Gautham R. Shenoy, Hari Bathini, Ian
   Munsie, Ivan Mikhaylov, Javier Martinez Canillas, Madhavan Srinivasan,
   Masahiro Yamada, Matt Brown, Michael Neuling, Michal Suchanek, Murilo
   Opsfelder Araujo, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Paul
   Mackerras, Pavel Machek, Russell Currey, Santosh Sivaraj, Stephen Rothwell,
   Thiago Jung Bauermann, Yang Li.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZXyPCAAoJEFHr6jzI4aWAI9QQAISf2x5y//cqCi4ISyQB5pTq
 KLS/yQajNkQOw7c0fzBZOaH5Xd/SJ6AcKWDg8yDlpDR3+sRRsr98iIRECgKS5I7/
 DxD9ywcbSoMXFQQo1ZMCp5CeuMUIJRtugBnUQM+JXCSUCPbznCY5DchDTLyTBTpO
 MeMVhI//JxthhoOMA9MudiEGaYCU9ho442Z4OJUSiLUv8WRbvQX9pTqoc4vx1fxA
 BWf2mflztBVcIfKIyxIIIlDLukkMzix6gSYPMCbC7lzkbnU7JSqKiheJXjo1gJS2
 ePHKDxeNR2/QP0g/j3aT/MR1uTt9MaNBSX3gANE1xQ9OoJ8m1sOtCO4gNbSdLWae
 eXhDnoiEp930DRZOeEioOItuWWoxFaMyYk3BMmRKV4QNdYL3y3TRVeL2/XmRGqYL
 Lxz4IY/x5TteFEJNGcRX90uizNSi8AaEXPF16pUk8Ctt6eH3ZSwPMv2fHeYVCMr0
 KFlKHyaPEKEoztyzLcUR6u9QB56yxDN58bvLpd32AeHvKhqyxFoySy59x9bZbatn
 B2y8mmDItg860e0tIG6jrtplpOVvL8i5jla5RWFVoQDuxxrLAds3vG9JZQs+eRzx
 Fiic93bqeUAS6RzhXbJ6QQJYIyhE7yqpcgv7ME1W87SPef3HPBk9xlp3yIDwdA2z
 bBDvrRnvupusz8qCWrxe
 =w8rj
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "Highlights include:

   - Support for STRICT_KERNEL_RWX on 64-bit server CPUs.

   - Platform support for FSP2 (476fpe) board

   - Enable ZONE_DEVICE on 64-bit server CPUs.

   - Generic & powerpc spin loop primitives to optimise busy waiting

   - Convert VDSO update function to use new update_vsyscall() interface

   - Optimisations to hypercall/syscall/context-switch paths

   - Improvements to the CPU idle code on Power8 and Power9.

  As well as many other fixes and improvements.

  Thanks to: Akshay Adiga, Andrew Donnellan, Andrew Jeffery, Anshuman
  Khandual, Anton Blanchard, Balbir Singh, Benjamin Herrenschmidt,
  Christophe Leroy, Christophe Lombard, Colin Ian King, Dan Carpenter,
  Gautham R. Shenoy, Hari Bathini, Ian Munsie, Ivan Mikhaylov, Javier
  Martinez Canillas, Madhavan Srinivasan, Masahiro Yamada, Matt Brown,
  Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Naveen N.
  Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pavel Machek,
  Russell Currey, Santosh Sivaraj, Stephen Rothwell, Thiago Jung
  Bauermann, Yang Li"

* tag 'powerpc-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
  powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs
  powerpc/mm/radix: Implement STRICT_RWX/mark_rodata_ro() for Radix
  powerpc/mm/hash: Implement mark_rodata_ro() for hash
  powerpc/vmlinux.lds: Align __init_begin to 16M
  powerpc/lib/code-patching: Use alternate map for patch_instruction()
  powerpc/xmon: Add patch_instruction() support for xmon
  powerpc/kprobes/optprobes: Use patch_instruction()
  powerpc/kprobes: Move kprobes over to patch_instruction()
  powerpc/mm/radix: Fix execute permissions for interrupt_vectors
  powerpc/pseries: Fix passing of pp0 in updatepp() and updateboltedpp()
  powerpc/64s: Blacklist rtas entry/exit from kprobes
  powerpc/64s: Blacklist functions invoked on a trap
  powerpc/64s: Un-blacklist system_call() from kprobes
  powerpc/64s: Move system_call() symbol to just after setting MSR_EE
  powerpc/64s: Blacklist system_call() and system_call_common() from kprobes
  powerpc/64s: Convert .L__replay_interrupt_return to a local label
  powerpc64/elfv1: Only dereference function descriptor for non-text symbols
  cxl: Export library to support IBM XSL
  powerpc/dts: Use #include "..." to include local DT
  powerpc/perf/hv-24x7: Aggregate result elements on POWER9 SMT8
  ...
2017-07-07 13:55:45 -07:00
Linus Torvalds 408c9861c6 Power management updates for v4.13-rc1
- Rework suspend-to-idle to allow it to take wakeup events signaled
    by the EC into account on ACPI-based platforms in order to properly
    support power button wakeup from suspend-to-idle on recent Dell
    laptops (Rafael Wysocki).
 
    That includes the core suspend-to-idle code rework, support for
    the Low Power S0 _DSM interface, and support for the ACPI INT0002
    Virtual GPIO device from Hans de Goede (required for USB keyboard
    wakeup from suspend-to-idle to work on some machines).
 
  - Stop trying to export the current CPU frequency via /proc/cpuinfo
    on x86 as that is inaccurate and confusing (Len Brown).
 
  - Rework the way in which the current CPU frequency is exported by
    the kernel (over the cpufreq sysfs interface) on x86 systems with
    the APERF and MPERF registers by always using values read from
    these registers, when available, to compute the current frequency
    regardless of which cpufreq driver is in use (Len Brown).
 
  - Rework the PCI/ACPI device wakeup infrastructure to remove the
    questionable and artificial distinction between "devices that
    can wake up the system from sleep states" and "devices that can
    generate wakeup signals in the working state" from it, which
    allows the code to be simplified quite a bit (Rafael Wysocki).
 
  - Fix the wakeup IRQ framework by making it use SRCU instead of
    RCU which doesn't allow sleeping in the read-side critical
    sections, but which in turn is expected to be allowed by the
    IRQ bus locking infrastructure (Thomas Gleixner).
 
  - Modify some computations in the intel_pstate driver to avoid
    rounding errors resulting from them (Srinivas Pandruvada).
 
  - Reduce the overhead of the intel_pstate driver in the HWP
    (hardware-managed P-states) mode and when the "performance"
    P-state selection algorithm is in use by making it avoid
    registering scheduler callbacks in those cases (Len Brown).
 
  - Rework the energy_performance_preference sysfs knob in
    intel_pstate by changing the values that correspond to
    different symbolic hint names used by it (Len Brown).
 
  - Make it possible to use more than one cpuidle driver at the same
    time on ARM (Daniel Lezcano).
 
  - Make it possible to prevent the cpuidle menu governor from using
    the 0 state by disabling it via sysfs (Nicholas Piggin).
 
  - Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
    on AMD systems (Yazen Ghannam).
 
  - Make the CPPC cpufreq driver take the lowest nonlinear performance
    information into account (Prashanth Prakash).
 
  - Add support for hi3660 to the cpufreq-dt driver, fix the
    imx6q driver and clean up the sfi, exynos5440 and intel_pstate
    drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
    Rafael Wysocki, Tao Wang).
 
  - Fix a few minor issues in the generic power domains (genpd)
    framework and clean it up somewhat (Krzysztof Kozlowski,
    Mikko Perttunen, Viresh Kumar).
 
  - Fix a couple of minor issues in the operating performance points
    (OPP) framework and clean it up somewhat (Viresh Kumar).
 
  - Fix a CONFIG dependency in the hibernation core and clean it up
    slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
 
  - Add rk3228 support to the rockchip-io adaptive voltage scaling
    (AVS) driver (David Wu).
 
  - Fix an incorrect bit shift operation in the RAPL power capping
    driver (Adam Lessnau).
 
  - Add support for the EPP field in the HWP (hardware managed
    P-states) control register, HWP.EPP, to the x86_energy_perf_policy
    tool and update msr-index.h with HWP.EPP values (Len Brown).
 
  - Fix some minor issues in the turbostat tool (Len Brown).
 
  - Add support for AMD family 0x17 CPUs to the cpupower tool and fix
    a minor issue in it (Sherry Hurwitz).
 
  - Assorted cleanups, mostly related to the constification of some
    data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
    Kozlowski).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZWrICAAoJEILEb/54YlRxZYMQAIRhfbyDxKq+ByvSilUS8kTA
 AItwJ8FFzykhiwN75Cqabg4rAGyWma7IRs1vzU7zeC1aEQIn+bTQtvk+utZNI+g2
 ANFlDha20q/sXsP/CDMMTIAdW9tSOC0TOvFI9s2V2Y8dJZhoekO4ctx34FAfUS5d
 Ao6rwSAWCMsCXcGaTAlqTA+TEJmBG7u6Iq6hq6ngltoFwOv3mWWBVn52VVaJ7SMp
 9/IPbbLGMFAedrgEBRGCR+MME1xZZpvcZIJaTt1Mgn7Cx3cJaysIUAvqY/SsvFGq
 5FcUTcF2qpK3+AGawiAxZIjvOBsGRtIwqKinNIzYWs/NjiIdzmgVAmTeuPtTqp+5
 HFehUdtkFcnuDnLqSNzAaZUa7tw84cJkwnbVMnesx0MkG6rZ1SeL22E2Sabpcdsh
 3Yo1ThzJSxi59DhiiE92EQnNCEjmCldRy+8q5Ag035muxl6EJYvuNBMnZv/BMCUn
 ltSNOrmps1DlN+Col8ORIeNzQ1YjYzWMqKAYzSbyccm4ug/iSHx0/DuESmQ4GTlF
 YCwkmqyWiHrBwpl51jc+4a7SGlMmKRqU+MJes0CjagaaqoUAb8qeBOpzEJ0yNwjZ
 wtI41l6blE6kbMD3yqGdCfiB2S7GlPVoxa15eX1wRyLH3fLjwwrzJirEaiBS86tI
 1PzHZEOmBlh3DYC6DBKA
 =Wsph
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "The big ticket items here are the rework of suspend-to-idle in order
  to add proper support for power button wakeup from it on recent Dell
  laptops and the rework of interfaces exporting the current CPU
  frequency on x86.

  In addition to that, support for a few new pieces of hardware is
  added, the PCI/ACPI device wakeup infrastructure is simplified
  significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
  bus locking infrastructure.

  Also, there are some functional improvements for intel_pstate, tools
  updates and small fixes and cleanups all over.

  Specifics:

   - Rework suspend-to-idle to allow it to take wakeup events signaled
     by the EC into account on ACPI-based platforms in order to properly
     support power button wakeup from suspend-to-idle on recent Dell
     laptops (Rafael Wysocki).

     That includes the core suspend-to-idle code rework, support for the
     Low Power S0 _DSM interface, and support for the ACPI INT0002
     Virtual GPIO device from Hans de Goede (required for USB keyboard
     wakeup from suspend-to-idle to work on some machines).

   - Stop trying to export the current CPU frequency via /proc/cpuinfo
     on x86 as that is inaccurate and confusing (Len Brown).

   - Rework the way in which the current CPU frequency is exported by
     the kernel (over the cpufreq sysfs interface) on x86 systems with
     the APERF and MPERF registers by always using values read from
     these registers, when available, to compute the current frequency
     regardless of which cpufreq driver is in use (Len Brown).

   - Rework the PCI/ACPI device wakeup infrastructure to remove the
     questionable and artificial distinction between "devices that can
     wake up the system from sleep states" and "devices that can
     generate wakeup signals in the working state" from it, which allows
     the code to be simplified quite a bit (Rafael Wysocki).

   - Fix the wakeup IRQ framework by making it use SRCU instead of RCU
     which doesn't allow sleeping in the read-side critical sections,
     but which in turn is expected to be allowed by the IRQ bus locking
     infrastructure (Thomas Gleixner).

   - Modify some computations in the intel_pstate driver to avoid
     rounding errors resulting from them (Srinivas Pandruvada).

   - Reduce the overhead of the intel_pstate driver in the HWP
     (hardware-managed P-states) mode and when the "performance" P-state
     selection algorithm is in use by making it avoid registering
     scheduler callbacks in those cases (Len Brown).

   - Rework the energy_performance_preference sysfs knob in intel_pstate
     by changing the values that correspond to different symbolic hint
     names used by it (Len Brown).

   - Make it possible to use more than one cpuidle driver at the same
     time on ARM (Daniel Lezcano).

   - Make it possible to prevent the cpuidle menu governor from using
     the 0 state by disabling it via sysfs (Nicholas Piggin).

   - Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
     AMD systems (Yazen Ghannam).

   - Make the CPPC cpufreq driver take the lowest nonlinear performance
     information into account (Prashanth Prakash).

   - Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
     driver and clean up the sfi, exynos5440 and intel_pstate drivers
     (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
     Wysocki, Tao Wang).

   - Fix a few minor issues in the generic power domains (genpd)
     framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
     Perttunen, Viresh Kumar).

   - Fix a couple of minor issues in the operating performance points
     (OPP) framework and clean it up somewhat (Viresh Kumar).

   - Fix a CONFIG dependency in the hibernation core and clean it up
     slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).

   - Add rk3228 support to the rockchip-io adaptive voltage scaling
     (AVS) driver (David Wu).

   - Fix an incorrect bit shift operation in the RAPL power capping
     driver (Adam Lessnau).

   - Add support for the EPP field in the HWP (hardware managed
     P-states) control register, HWP.EPP, to the x86_energy_perf_policy
     tool and update msr-index.h with HWP.EPP values (Len Brown).

   - Fix some minor issues in the turbostat tool (Len Brown).

   - Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
     minor issue in it (Sherry Hurwitz).

   - Assorted cleanups, mostly related to the constification of some
     data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
     Kozlowski)"

* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
  cpufreq: Update scaling_cur_freq documentation
  cpufreq: intel_pstate: Clean up after performance governor changes
  PM: hibernate: constify attribute_group structures.
  cpuidle: menu: allow state 0 to be disabled
  intel_idle: Use more common logging style
  PM / Domains: Fix missing default_power_down_ok comment
  PM / Domains: Fix unsafe iteration over modified list of domains
  PM / Domains: Fix unsafe iteration over modified list of domain providers
  PM / Domains: Fix unsafe iteration over modified list of device links
  PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
  PM / Domains: Call driver's noirq callbacks
  PM / core: Drop run_wake flag from struct dev_pm_info
  PCI / PM: Simplify device wakeup settings code
  PCI / PM: Drop pme_interrupt flag from struct pci_dev
  ACPI / PM: Consolidate device wakeup settings code
  ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
  PM / QoS: constify *_attribute_group.
  PM / AVS: rockchip-io: add io selectors and supplies for rk3228
  powercap/RAPL: prevent overridding bits outside of the mask
  PM / sysfs: Constify attribute groups
  ...
2017-07-04 13:39:41 -07:00
Nicholas Piggin 3ed09c9458 cpuidle: menu: allow state 0 to be disabled
The menu driver does not allow state0 to be disabled completely.
If it is disabled but other enabled states don't meet latency
requirements, it is still used.

Fix this by starting with the first enabled idle state. Fall back
to state 0 if no idle states are enabled (arguably this should be
-EINVAL if it is attempted, but this is the minimal fix).

Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-29 22:59:17 +02:00
Nicholas Piggin 7ded429152 cpuidle: powerpc: no memory barrier after break from idle
A memory barrier is not required after the task wakes up,
only if we clear the polling flag before waking. The case
where we have work to do is the important one, so optimise
for it.

Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-06-28 13:08:12 +10:00
Nicholas Piggin 624e46d035 cpuidle: powerpc: read mostly for common globals
Ensure these don't get put into bouncing cachelines.

Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-06-28 13:08:12 +10:00
Nicholas Piggin 3fc5ee927f cpuidle: powerpc: cpuidle set polling before enabling irqs
local_irq_enable can cause interrupts to be taken which could
take significant amount of processing time. The idle process
should set its polling flag before this, so another process that
wakes it during this time will not have to send an IPI.

Expand the TIF_POLLING_NRFLAG coverage to as large as possible.

Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-06-28 13:08:11 +10:00
Daniel Lezcano d50a7d8acd ARM: cpuidle: Support asymmetric idle definition
Some hardware have clusters with different idle states. The current code does
not support this and fails as it expects all the idle states to be identical.

Because of this, the Mediatek mtk8173 had to create the same idle state for a
big.Little system and now the Hisilicon 960 is facing the same situation.

Solve this by simply assuming the multiple driver will be needed for all the
platforms using the ARM generic cpuidle driver which makes sense because of the
different topologies we can support with a single kernel for ARM32 or ARM64.

Every CPU has its own driver, so every single CPU can specify in the DT the
idle states.

This simple approach allows to support the future dynamIQ system, current SMP
and HMP.

Tested on:
 - 96boards: Hikey 620
 - 96boards: Hikey 960
 - 96boards: dragonboard410c
 - Mediatek 8173

Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-24 01:51:00 +02:00
Ingo Molnar 902b319413 Merge branch 'WIP.sched/core' into sched/core
Conflicts:
	kernel/sched/Makefile

Pick up the waitqueue related renames - it didn't get much feedback,
so it appears to be uncontroversial. Famous last words? ;-)

Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-06-20 12:28:21 +02:00
Nicholas Piggin 2201f994a5 powerpc/64s/idle: Move soft interrupt mask logic into C code
This simplifies the asm and fixes irq-off tracing over sleep
instructions.

Also move powersave_nap check for POWER8 into C code, and move
PSSCR register value calculation for POWER9 into C.

Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-06-19 19:46:26 +10:00
Rafael J. Wysocki f63e4f7d41 Merge branches 'pm-cpufreq', 'pm-cpuidle' and 'pm-devfreq'
* pm-cpufreq:
  cpufreq: conservative: Allow down_threshold to take values from 1 to 10
  Revert "cpufreq: schedutil: Reduce frequencies slower"

* pm-cpuidle:
  cpuidle: dt: Add missing 'of_node_put()'

* pm-devfreq:
  PM / devfreq: exynos-ppmu: Staticize event list
  PM / devfreq: exynos-ppmu: Handle return value of clk_prepare_enable
  PM / devfreq: exynos-nocp: Handle return value of clk_prepare_enable
2017-06-15 01:51:33 +02:00
Christophe Jaillet b2cdd8e1b5 cpuidle: dt: Add missing 'of_node_put()'
'of_node_put()' should be called on pointer returned by
'of_parse_phandle()' when done. In this function this is done in all path
except this 'continue', so add it.

Fixes: 97735da074 (drivers: cpuidle: Add status property to ARM idle states)
Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-06-12 14:36:13 +02:00
Gautham R. Shenoy f9122ee4f5 cpuidle-powernv: Allow Deep stop states that don't stop time
The current code in the cpuidle-powernv intialization only allows deep
stop states (indicated by OPAL_PM_STOP_INST_DEEP) which lose timebase
(indicated by OPAL_PM_TIMEBASE_STOP). This assumption goes back to
POWER8 time where deep states used to lose the timebase. However, on
POWER9, we do have stop states that are deep (they lose hypervisor
state) but retain the timebase.

Fix the initialization code in the cpuidle-powernv driver to allow
such deep states.

Further, there is a bug in cpuidle-powernv driver with
CONFIG_TICK_ONESHOT=n where we end up incrementing the nr_idle_states
even if a platform idle state which loses time base was not added to
the cpuidle table.

Fix this by ensuring that the nr_idle_states variable gets incremented
only when the platform idle state was added to the cpuidle table.

Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-05-30 14:59:51 +10:00
Peter Zijlstra f9fccdb9ef cpuidle: Fix idle time tracking
Ville reported that on his Core2, which has TSC stop in idle, we would
always report very short idle durations. He tracked this down to
commit:

  e93e59ce5b ("cpuidle: Replace ktime_get() with local_clock()")

which replaces ktime_get() with local_clock().

Add a sched_clock_idle_wakeup_event() call, which will re-sync the
clock with ktime_get_ns() when TSC is unstable and no-op otherwise.

Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Fixes: e93e59ce5b ("cpuidle: Replace ktime_get() with local_clock()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-05-15 10:15:20 +02:00
Rafael J. Wysocki 80449d89d4 Merge branches 'pm-domains', 'pm-cpuidle', 'pm-sleep' and 'powercap'
* pm-domains:
  PM / Domains: Add DT file to MAINTAINERS
  PM / Domains: Fix DT example

* pm-cpuidle:
  x86/intel_idle: add Gemini Lake support
  cpuidle: check dev before usage in cpuidle_use_deepest_state()

* pm-sleep:
  ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle
  PM / wakeup: Integrate mechanism to abort transitions in progress

* powercap:
  powercap: intel_rapl: Add support for Gemini Lake
2017-05-09 23:21:46 +02:00
Li, Fei 41dc750ea6 cpuidle: check dev before usage in cpuidle_use_deepest_state()
In case of there is no cpuidle devices registered, dev will be null, and
panic will be triggered like below;
In this patch, add checking of dev before usage, like that done in
cpuidle_idle_call.

Panic without fix:
[  184.961328] BUG: unable to handle kernel NULL pointer dereference at
  (null)
[  184.961328] IP: cpuidle_use_deepest_state+0x30/0x60
...
[  184.961328]  play_idle+0x8d/0x210
[  184.961328]  ? __schedule+0x359/0x8e0
[  184.961328]  ? _raw_spin_unlock_irqrestore+0x28/0x50
[  184.961328]  ? kthread_queue_delayed_work+0x41/0x80
[  184.961328]  clamp_idle_injection_func+0x64/0x1e0

Fixes: bb8313b603 (cpuidle: Allow enforcing deepest idle state selection)
Signed-off-by: Li, Fei <fei.li@intel.com>
Tested-by: Shi, Feng <fengx.shi@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-05-01 23:17:20 +02:00
Rafael J. Wysocki 060d0fbb43 Merge branches 'pm-cpuidle', 'pm-core', 'pm-domains', 'pm-avs' and 'pm-devfreq'
* pm-cpuidle:
  cpuidle: powernv: Avoid a branch in the core snooze_loop() loop
  cpuidle: powernv: Don't continually set thread priority in snooze_loop()
  cpuidle: powernv: Don't bounce between low and very low thread priority
  cpuidle: cpuidle-cps: remove unused variable
  powernv-cpuidle: Validate DT property array size

* pm-core:
  PM / runtime: Document autosuspend-helper side effects
  PM / runtime: Fix autosuspend documentation

* pm-domains:
  PM / Domains: Ignore domain-idle-states that are not compatible
  PM / Domains: Don't warn about IRQ safe device for an always on PM domain
  PM / Domains: Respect errors from genpd's ->power_off() callback
  PM / Domains: Enable users of genpd to specify always on PM domains
  PM / Domains: Clean up code validating genpd's status
  PM / Domain: remove conditional from error case

* pm-avs:
  PM / AVS: rockchip-io: add io selectors and supplies for rk3328

* pm-devfreq:
  PM / devfreq: Move struct devfreq_governor to devfreq directory
2017-04-28 23:15:34 +02:00
Anton Blanchard 0baa91cb73 cpuidle: powernv: Avoid a branch in the core snooze_loop() loop
When in the snooze_loop() we want to take up the least amount of
resources. On my version of gcc (6.3), we end up with an extra
branch because it predicts snooze_timeout_en to be false, whereas it
is almost always true.

Use likely() to avoid the branch and be a little nicer to the
other non idle threads on the core.

Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-19 23:17:19 +02:00
Anton Blanchard 26eb48a9fa cpuidle: powernv: Don't continually set thread priority in snooze_loop()
The powerpc64 kernel exception handlers have preserved thread priorities
for a long time now, so there is no need to continually set it.

Just set it once on entry and once exit.

Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-19 23:17:18 +02:00
Anton Blanchard 79b578111f cpuidle: powernv: Don't bounce between low and very low thread priority
The core of snooze_loop() continually bounces between low and very
low thread priority. Changing thread priorities is an expensive
operation that can negatively impact other threads on a core.

All CPUs that can run PowerNV support very low priority, so we can
avoid the change completely.

Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-19 23:17:18 +02:00
Marcin Nowakowski 02018b3929 cpuidle: cpuidle-cps: remove unused variable
'core' in cps_cpuidle_init has never been used and is unnecessary, so
remove the dead code.

Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-04-19 23:04:54 +02:00
Vaidyanathan Srinivasan 293d264f13 cpuidle: powernv: Pass correct drv->cpumask for registration
drv->cpumask defaults to cpu_possible_mask in __cpuidle_driver_init().
On PowerNV platform cpu_present could be less than cpu_possible in cases
where firmware detects the cpu, but it is not available to the OS.  When
CONFIG_HOTPLUG_CPU=n, such cpus are not hotplugable at runtime and hence
we skip creating cpu_device.

This breaks cpuidle on powernv where register_cpu() is not called for
cpus in cpu_possible_mask that cannot be hot-added at runtime.

Trying cpuidle_register_device() on cpu without cpu_device will cause
crash like this:

cpu 0xf: Vector: 380 (Data SLB Access) at [c000000ff1503490]
    pc: c00000000022c8bc: string+0x34/0x60
    lr: c00000000022ed78: vsnprintf+0x284/0x42c
    sp: c000000ff1503710
   msr: 9000000000009033
   dar: 6000000060000000
  current = 0xc000000ff1480000
  paca    = 0xc00000000fe82d00   softe: 0        irq_happened: 0x01
    pid   = 1, comm = swapper/8
Linux version 4.11.0-rc2 (sv@sagarika) (gcc version 4.9.4
(Buildroot 2017.02-00004-gc28573e) ) #15 SMP Fri Mar 17 19:32:02 IST 2017
enter ? for help
[link register   ] c00000000022ed78 vsnprintf+0x284/0x42c
[c000000ff1503710] c00000000022ebb8 vsnprintf+0xc4/0x42c (unreliable)
[c000000ff1503800] c00000000022ef40 vscnprintf+0x20/0x44
[c000000ff1503830] c0000000000ab61c vprintk_emit+0x94/0x2cc
[c000000ff15038a0] c0000000000acc9c vprintk_func+0x60/0x74
[c000000ff15038c0] c000000000619694 printk+0x38/0x4c
[c000000ff15038e0] c000000000224950 kobject_get+0x40/0x60
[c000000ff1503950] c00000000022507c kobject_add_internal+0x60/0x2c4
[c000000ff15039e0] c000000000225350 kobject_init_and_add+0x70/0x78
[c000000ff1503a60] c00000000053c288 cpuidle_add_sysfs+0x9c/0xe0
[c000000ff1503ae0] c00000000053aeac cpuidle_register_device+0xd4/0x12c
[c000000ff1503b30] c00000000053b108 cpuidle_register+0x98/0xcc
[c000000ff1503bc0] c00000000085eaf0 powernv_processor_idle_init+0x140/0x1e0
[c000000ff1503c60] c00000000000cd60 do_one_initcall+0xc0/0x15c
[c000000ff1503d20] c000000000833e84 kernel_init_freeable+0x1a0/0x25c
[c000000ff1503dc0] c00000000000d478 kernel_init+0x24/0x12c
[c000000ff1503e30] c00000000000b564 ret_from_kernel_thread+0x5c/0x78

This patch fixes the bug by passing correct cpumask from
powernv-cpuidle driver.

Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
[ rjw: Comment massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-03-29 22:55:36 +02:00
Gautham R. Shenoy ecad4502d0 powernv-cpuidle: Validate DT property array size
The various properties associated with powernv idle states such as
names, flags, residency-ns, latencies-ns, psscr, psscr-mask are
exposed in the device-tree as property arrays such the pointwise
entries in each of these arrays correspond to the properties of the
same idle state.

This patch validates that the lengths of the property arrays are the
same. If there is a mismatch, the patch will ensure that we bail out
and not expose the platform idle states via cpuidle.

Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-03-29 00:14:00 +02:00
Vaidyanathan Srinivasan ad0a45fd9c cpuidle: Validate cpu_dev in cpuidle_add_sysfs()
If a given cpu is not in cpu_present and cpu hotplug
is disabled, arch can skip setting up the cpu_dev.

Arch cpuidle driver should pass correct cpu mask
for registration, but failing to do so by the driver
causes error to propagate and crash like this:

[   30.076045] Unable to handle kernel paging request for data at address 0x00000048
[   30.076100] Faulting instruction address: 0xc0000000007b2f30
cpu 0x4d: Vector: 300 (Data Access) at [c000003feb18b670]
    pc: c0000000007b2f30: kobject_get+0x20/0x70
    lr: c0000000007b3c94: kobject_add_internal+0x54/0x3f0
    sp: c000003feb18b8f0
   msr: 9000000000009033
   dar: 48
 dsisr: 40000000
  current = 0xc000003fd2ed8300
  paca    = 0xc00000000fbab500   softe: 0        irq_happened: 0x01
    pid   = 1, comm = swapper/0
Linux version 4.11.0-rc2-svaidy+ (sv@sagarika) (gcc version 6.2.0
20161005 (Ubuntu 6.2.0-5ubuntu12) ) #10 SMP Sun Mar 19 00:08:09 IST 2017
enter ? for help
[c000003feb18b960] c0000000007b3c94 kobject_add_internal+0x54/0x3f0
[c000003feb18b9f0] c0000000007b43a4 kobject_init_and_add+0x64/0xa0
[c000003feb18ba70] c000000000e284f4 cpuidle_add_sysfs+0xb4/0x130
[c000003feb18baf0] c000000000e26038 cpuidle_register_device+0x118/0x1c0
[c000003feb18bb30] c000000000e26c48 cpuidle_register+0x78/0x120
[c000003feb18bbc0] c00000000168fd9c powernv_processor_idle_init+0x110/0x1c4
[c000003feb18bc40] c00000000000cff8 do_one_initcall+0x68/0x1d0
[c000003feb18bd00] c0000000016242f4 kernel_init_freeable+0x280/0x360
[c000003feb18bdc0] c00000000000d864 kernel_init+0x24/0x160
[c000003feb18be30] c00000000000b4e8 ret_from_kernel_thread+0x5c/0x74

Validating cpu_dev fixes the crash and reports correct error message like:

[   30.163506] Failed to register cpuidle device for cpu136
[   30.173329] Registration of powernv driver failed.

Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
[ rjw: Comment massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-03-21 22:26:37 +01:00
Linus Torvalds 1827adb11a Merge branch 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up from Ingo Molnar:
 "The point of these changes is to significantly reduce the
  <linux/sched.h> header footprint, to speed up the kernel build and to
  have a cleaner header structure.

  After these changes the new <linux/sched.h>'s typical preprocessed
  size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
  lines), which is around 40% faster to build on typical configs.

  Not much changed from the last version (-v2) posted three weeks ago: I
  eliminated quirks, backmerged fixes plus I rebased it to an upstream
  SHA1 from yesterday that includes most changes queued up in -next plus
  all sched.h changes that were pending from Andrew.

  I've re-tested the series both on x86 and on cross-arch defconfigs,
  and did a bisectability test at a number of random points.

  I tried to test as many build configurations as possible, but some
  build breakage is probably still left - but it should be mostly
  limited to architectures that have no cross-compiler binaries
  available on kernel.org, and non-default configurations"

* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
  sched/headers: Clean up <linux/sched.h>
  sched/headers: Remove #ifdefs from <linux/sched.h>
  sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
  sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
  sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
  sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
  sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
  sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
  sched/core: Remove unused prefetch_stack()
  sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
  sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
  sched/headers: Remove <linux/signal.h> from <linux/sched.h>
  sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
  sched/headers: Remove the runqueue_is_locked() prototype
  sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
  sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
  sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
  sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
  sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
  sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
  ...
2017-03-03 10:16:38 -08:00
Linus Torvalds 080e4168c0 More power management updates for v4.11-rc1
- Fix for a cpuidle menu governor problem that started to take an
    unnecessary spinlock after one of the recent updates and that
    did not play well with the RT patch (Rafael Wysocki).
 
  - Fix for the new intel_pstate operation mode switching feature
    added recently that did not reinitialize P-state limits properly
    when switching operation modes (Rafael Wysocki).
 
  - Removal of unused global notifiers from the PM QoS framework
    (Viresh Kumar).
 
  - Generic power domains framework update to make it handle
    asynchronous invocations of PM callbacks in the "noirq" phases
    of system suspend/hibernation correctly (Ulf Hansson).
 
  - Two hibernation core cleanups (Rafael Wysocki).
 
  - intel_idle cleanup related to the sysfs interface (Len Brown).
 
  - Off-by-one bug fix in the OPP (Operating Performance Points)
    framework (Andrzej Hajda).
 
  - OPP framework's documentation fix (Viresh Kumar).
 
  - cpufreq qoriq driver cleanup (Tang Yuantian).
 
  - Fixes for typos in comments in the device runtime PM framework
    (Christophe Jaillet).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJYuLeGAAoJEILEb/54YlRxJvcP/0BRmh8Hn4Itx/NIWNg71X6j
 U+v8Pn8T3MP33gCcleLYlgre2JUIAUDmhdK99+UOx+/abhjMhQSaF3HhTOwYaPtQ
 6njoHVS0NnfqUf+x5kp+EpRxBVNucYVbdRTVd1DsHIeLLz/96DFOzb/R7tko/pKx
 pFMWvNdotHLLgXOG1UvdRimwTDlFMffxFzD8Se53LPjRXS0S73A5VWfqZOye44Re
 j3W1AJ0Idgq5uduA6J8x1MWbaxDq1h+j6CSUm05yvqrINzxXwXt0Hv6stCQTo+Gb
 YMdiBd8MujNyAgcchw3jiDQ8Vp+zmfLPcHrfPe//SSefj26eB8LyVNSYelvbUdOz
 cNjvyErva37MmaegCL9QC7WbLM+A7VE6bU6YzDCi/rR8jYMJ51Fb9jGiYb/oimry
 OLlblEekikUsskWv4hGV1JVt5VhmUMlagWtexxn+lMszATcZro0tfXu/vgQWksYs
 noUnwuWJWxvj2aNMsvbzW3HLlTGSmYl2UxJ7IymQQaTDblwF9Kg61rm3+5coUctd
 ifceynDVp9Gju25faYgZ+Dq9+o8ktlOGOHRRPdLIRNJ/T+4tUDnlGkdbPb+Tfn03
 XUIzYCu74U8/oW8gOk6t0WpmWzvxEXNgdirdEIR6y3loYIC0Jr3v4gyD975Eug74
 Hzfrdg7ignAmWV+nf6UY
 =SeUF
 -----END PGP SIGNATURE-----

Merge tag 'pm-extra-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull more power management updates deom Rafael Wysocki:
 "These fix two bugs introduced by recent power management updates (in
  the cpuidle menu governor and intel_pstate) and a few other issues,
  clean up things and remove unused code.

  Specifics:

   - Fix for a cpuidle menu governor problem that started to take an
     unnecessary spinlock after one of the recent updates and that did
     not play well with the RT patch (Rafael Wysocki).

   - Fix for the new intel_pstate operation mode switching feature added
     recently that did not reinitialize P-state limits properly when
     switching operation modes (Rafael Wysocki).

   - Removal of unused global notifiers from the PM QoS framework
     (Viresh Kumar).

   - Generic power domains framework update to make it handle
     asynchronous invocations of PM callbacks in the "noirq" phases of
     system suspend/hibernation correctly (Ulf Hansson).

   - Two hibernation core cleanups (Rafael Wysocki).

   - intel_idle cleanup related to the sysfs interface (Len Brown).

   - Off-by-one bug fix in the OPP (Operating Performance Points)
     framework (Andrzej Hajda).

   - OPP framework's documentation fix (Viresh Kumar).

   - cpufreq qoriq driver cleanup (Tang Yuantian).

   - Fixes for typos in comments in the device runtime PM framework
     (Christophe Jaillet)"

* tag 'pm-extra-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / OPP: Documentation: Fix opp-microvolt in examples
  intel_idle: stop exposing platform acronyms in sysfs
  cpufreq: intel_pstate: Fix limits issue with operation mode switching
  PM / hibernate: Define pr_fmt() and use pr_*() instead of printk()
  PM / hibernate: Untangle power_down()
  cpuidle: menu: Avoid taking spinlock for accessing QoS values
  PM / QoS: Remove global notifiers
  PM / runtime: Fix some typos
  cpufreq: qoriq: clean up unused code
  PM / OPP: fix off-by-one bug in dev_pm_opp_get_max_volt_latency loop
  PM / Domains: Power off masters immediately in the power off sequence
  PM / Domains: Rename is_async to one_dev_on for genpd_power_off()
  PM / Domains: Move genpd_power_off() above genpd_power_on()
2017-03-02 17:33:52 -08:00
Ingo Molnar 03441a3482 sched/headers: Prepare for new header dependencies before moving code to <linux/sched/stat.h>
We are going to split <linux/sched/stat.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.

Create a trivial placeholder <linux/sched/stat.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.

Include the new header in the files that are going to need it.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:34 +01:00
Ingo Molnar 4f17722c72 sched/headers: Prepare for new header dependencies before moving code to <linux/sched/loadavg.h>
We are going to split <linux/sched/loadavg.h> out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.

Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.

Include the new header in the files that are going to need it.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:27 +01:00
Ingo Molnar e601757102 sched/headers: Prepare for new header dependencies before moving code to <linux/sched/clock.h>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.

Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.

Include the new header in the files that are going to need it.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:27 +01:00
Ingo Molnar 4c822698cb sched/headers: Prepare for new header dependencies before moving code to <linux/sched/idle.h>
We are going to split  <linux/sched/idle.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.

Create a trivial placeholder <linux/sched/idle.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.

Include the new header in the files that are going to need it.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:26 +01:00
Rafael J. Wysocki 6dbf5cea05 cpuidle: menu: Avoid taking spinlock for accessing QoS values
After commit 9908859aca (cpuidle/menu: add per CPU PM QoS resume
latency consideration) the cpuidle menu governor calls
dev_pm_qos_read_value() on CPU devices to read the current resume
latency QoS constraint values for them.  That function takes a spinlock
to prevent the device's power.qos pointer from becoming NULL during
the access which is a problem for the RT patchset where spinlocks are
converted into mutexes and the idle loop stops working.

However, it is not even necessary for the menu governor to take
that spinlock, because the power.qos pointer accessed under it
cannot be modified during the access anyway.

For this reason, introduce a "raw" routine for accessing device
QoS resume latency constraints without locking and use it in the
menu governor.

Fixes: 9908859aca (cpuidle/menu: add per CPU PM QoS resume latency consideration)
Acked-by: Alex Shi <alex.shi@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-02-27 15:07:38 +01:00
Linus Torvalds 38705613b7 powerpc updates for 4.11 part 1.
Highlights include:
 
  - Support for direct mapped LPC on POWER9, giving Linux direct access to
    devices that may be on there such as a UART.
 
  - Memory hotplug support for the Power9 Radix MMU.
 
  - Add new AUX vectors describing the processor's cache geometry, to be used by
    glibc.
 
  - The ability for a guest to ask the hypervisor to resize the guest's hash
    table, and in addition support for doing so automatically when memory is
    hotplugged into/out-of the guest. This allows the hash table to be sized
    based on the current memory usage of the guest, rather than the maximum
    possible memory usage.
 
  - Implementation of optprobes (kprobe optimisation) for powerpc.
 
 In addition there's the topic branch shared with the KVM tree, which includes
 support for guests to use the Radix MMU on Power9.
 
 Thanks to:
   Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton Blanchard,
   Benjamin Herrenschmidt, Chris Packham, Daniel Axtens, Daniel Borkmann, David
   Gibson, Finn Thain, Gautham R. Shenoy, Gavin Shan, Greg Kurz, Joel Stanley,
   John Allen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
   Neuling, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi
   Bangoria, Reza Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJYrWj0AAoJEFHr6jzI4aWAsn4P/08Kz3TtOvDuuPGVNoO7fWOn
 ag5/zVt8R4FuCALqWpAZbVqMuUU4wLxG0RuWlmBNYYhrjMC6JxHpOSjQXxM2D7YT
 CdGTJxG414r6HMOeToL9i/z33o0m+KT07tscer+QMKlXVKCR2z0fEJch+zoPBHYA
 5eVBFpLLTtbNiX9UnrcM/vYz61d56kT4YJey9/8qbAkTAc1rMPa8ucU5UiKYJ7yX
 mF8cd7WE+7aqif9V8yN59G2rcbz+h3pbMw/gzImiYsYrUj4fLjU+VTKL5PPT+UFy
 WWBXD3MAMm1dksMMZi3hgoo2BZhDn3RkymeYi6Jo4kDknNMPZzkMxGyvaJ8Eq5H/
 bIYXdS1AbTtvaaEEuWqDFjpnChOEvj/8IeqitU0jjlql8BVjNKg/ESaaKucZr+pO
 pk2Mfvw0Tb/lxJT5qj27yq4aRsxJwdFOoPYCN7MquPp/wV2Tg5M6h4nVQ4T6Wl0S
 tMFQeCqXflhDWh0Xgr2UXpF66/YTj3Du5LasOTkgGeU30Z8TcNGFEmDWShKP3cEm
 e0oQE+OHhIGN4WSBXBAto/Gw8/0v3pXlMs+VEfeHqenwPss2sWtSwXWe8khmiy9e
 DJ48sTzj75/Zx1fiqRldw9YEnrL+NK0eOOpvzxeyKpfvdUytc+chFfEqUmO6kl3Z
 DW2UmlZxmW+b0SfexCHL
 =Icle
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc updates from Michael Ellerman:
 "Highlights include:

   - Support for direct mapped LPC on POWER9, giving Linux direct access
     to devices that may be on there such as a UART.

   - Memory hotplug support for the Power9 Radix MMU.

   - Add new AUX vectors describing the processor's cache geometry, to
     be used by glibc.

   - The ability for a guest to ask the hypervisor to resize the guest's
     hash table, and in addition support for doing so automatically when
     memory is hotplugged into/out-of the guest. This allows the hash
     table to be sized based on the current memory usage of the guest,
     rather than the maximum possible memory usage.

   - Implementation of optprobes (kprobe optimisation) for powerpc.

  In addition there's the topic branch shared with the KVM tree, which
  includes support for guests to use the Radix MMU on Power9.

  Thanks to:
    Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
    Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
    Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
    Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
    Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
    Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
    Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"

* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
  powerpc/mm/radix: Skip ptesync in pte update helpers
  powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
  powerpc/mm/radix: Update pte update sequence for pte clear case
  powerpc/mm: Update PROTFAULT handling in the page fault path
  powerpc/xmon: Fix data-breakpoint
  powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
  powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
  powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
  powerpc/pseries: Fix typo in parameter description
  powerpc/kprobes: Remove kprobe_exceptions_notify()
  kprobes: Introduce weak variant of kprobe_exceptions_notify()
  powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
  powerpc/powernv: Fix opal_exit tracepoint opcode
  powerpc: Add a prototype for mcount() so it can be versioned
  powerpc: Drop GPL from of_node_to_nid() export to match other arches
  powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
  powerpc/kprobes: Implement Optprobes
  powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
  powerpc: Add helper to check if offset is within relative branch range
  powerpc/bpf: Introduce __PPC_SH64()
  ...
2017-02-22 10:30:38 -08:00
Gautham R. Shenoy 09206b600c powernv: Pass PSSCR value and mask to power9_idle_stop
The power9_idle_stop method currently takes only the requested stop
level as a parameter and picks up the rest of the PSSCR bits from a
hand-coded macro. This is not a very flexible design, especially when
the firmware has the capability to communicate the psscr value and the
mask associated with a particular stop state via device tree.

This patch modifies the power9_idle_stop API to take as parameters the
PSSCR value and the PSSCR mask corresponding to the stop state that
needs to be set. These PSSCR value and mask are respectively obtained
by parsing the "ibm,cpu-idle-state-psscr" and
"ibm,cpu-idle-state-psscr-mask" fields from the device tree.

In addition to this, the patch adds support for handling stop states
for which ESL and EC bits in the PSSCR are zero. As per the
architecture, a wakeup from these stop states resumes execution from
the subsequent instruction as opposed to waking up at the System
Vector.

The older firmware sets only the Requested Level (RL) field in the
psscr and psscr-mask exposed in the device tree. For older firmware
where psscr-mask=0xf, this patch will set the default sane values that
the set for for remaining PSSCR fields (i.e PSLL, MTL, ESL, EC, and
TR). For the new firmware, the patch will validate that the invariants
required by the ISA for the psscr values are maintained by the
firmware.

This skiboot patch that exports fully populated PSSCR values and the
mask for all the stop states can be found here:
https://lists.ozlabs.org/pipermail/skiboot/2016-September/004869.html

[Optimize the number of instructions before entering STOP with
ESL=EC=0, validate the PSSCR values provided by the firimware
maintains the invariants required as per the ISA suggested by Balbir
Singh]

Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-01-31 08:32:13 +11:00
Gautham R. Shenoy 9e9fc6f00a cpuidle:powernv: Add helper function to populate powernv idle states.
In the current code for powernv_add_idle_states, there is a lot of code
duplication while initializing an idle state in powernv_states table.

Add an inline helper function to populate the powernv_states[] table
for a given idle state. Invoke this for populating the "Nap",
"Fastsleep" and the stop states in powernv_add_idle_states.

Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-01-31 08:32:13 +11:00
Alex Shi 9908859aca cpuidle/menu: add per CPU PM QoS resume latency consideration
There may be special requirements on CPU response time, like if a
interrupt is pinned to a CPU, that CPU should not go into excessively
deep idle states.  For this reason, add a mechanism for adding
PM QoS resume latency constraints for individual CPUs and modify the
menu governor to take them into account.

To that end, extend the device PM QoS pm_qos_resume_latency attribute
to CPUs, which is possible, because the exit latency for CPUs is
effectively equivalent to the resume latency for devices.

Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Rik van Riel <riel@redhat.com>
[ rjw : Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-01-30 11:03:32 +01:00
Alex Shi 8e37e1a2a3 cpuidle/menu: stop seeking deeper idle if current state is deep enough
Obsolete commit 71abbbf856 (cpuidle: extend cpuidle and menu governor
to handle dynamic states) wanted to introduce dynamic C-states, but that
idea was dropped long ago.  The nonsense deeper C-state checking
remained, though.

Since both target_residency and exit_latency are longer for deeper
idle state, there's no need to waste CPU time on useless checks.

Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Rik van Riel <riel@redhat.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-01-30 10:56:00 +01:00
Linus Torvalds 7c0f6ba682 Replace <asm/uaccess.h> with <linux/uaccess.h> globally
This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-24 11:46:01 -08:00
Rafael J. Wysocki 0e7414b7aa cpuidle: Add a kerneldoc comment to cpuidle_use_deepest_state()
Since cpuidle_use_deepest_state() is not static, add a proper
kerneldoc comment to it to document its purpose.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-12-06 02:25:03 +01:00