Include linux/mfd/pcf50633/pmic.h instead of duplicating the same defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It should be marked as readable but wasn't, breaking DC servo operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using regmap apis for accessing the device registers and
using RBTREE caching mechanims for caching registers.
Enabling caching of the registers which is used for voltage
controls. By doing this, the modify_bits operation is faster as
it does not involve the i2c register read from device, just read
from cache. This results faster set voltage operation.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For 88pm860x pmic, it can wake the system from low power mode by irq,
its sub-devs like RTC and onkey can be enabled for this usage.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6030_irq_set_wake is not used anywhere else in the kernel
except as irq_chip.irq_set_wake. No reason for it to be exported.
Also fixes build warning:
drivers/mfd/twl6030-irq.c:230:5: warning: symbol 'twl6030_irq_set_wake' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6030 family of PMIC use a shadow interrupt status register
while kernel processes the current interrupt event.
However, any write(0 or 1) to register INT_STS_A, INT_STS_B or
INT_STS_C clears all 3 interrupt status registers.
Since clear of the interrupt is done on 32k clk, depending on I2C
bus speed, we could in-adverently clear the status of a interrupt
status pending on shadow register in the current implementation.
This is due to the fact that multi-byte i2c write operation into
three seperate status register could result in multiple load
and clear of status and result in lost interrupts.
Instead, doing a single byte write to INT_STS_A register with 0x0
will clear all three interrupt status registers without the related
risk.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
da9052 has been converted to use regmap API, so we can remove the unused
io_lock mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch allows to decouple and recouple the gic from the PRCMU.
This is needed to put the A9 core in retention mode with the cpuidle
driver.
It is based on top of the "DB8500 PRCMU update" patchset.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_base of the tps65912 irq platform data should be
initialized with the board provided irq_base data.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The code is currently always checking the first resource of every
device only (several times.) This has been broken since the ACPI check
was added in February 2010 in commit
91fedede03.
Fix the check to run on each resource individually, once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes warnings and needed for correctness.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There could be possible race condition where the host dev's
are alloced and added to platform dev just before usbhs_init.
Just move usbhs_init before adding child dev.
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the hardcoded magic values for dma mask and use the dma
mask api/macro available.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The callers of pcf50633_write_block assume pcf50633_write_block return 0 on
success, thus make it return 0 instead of the number of registers written on
success.
Currently pcf50633_write_block is called in drivers/mfd/pcf50633-irq.c and
drivers/rtc/rtc-pcf50633.c.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The val_len parameters for regmap_raw_write should be "count * sizeof(u8)"
(or simply "count") instead of "count * sizeof(u16)".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AB9540 variant of the AB8500 is basically close enough
to use the same driver. This adds the new registers and
deviations for this new chip variant.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This makes the AB8500 state struct contain the IRQ mask and
register offsets previously hard-coded so as to make room for
more AB8500 variants.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are currently four different versions of the AB8500
around: AB8500, AB8505, AB9540 and AB8540. Unfortunately:
- Some of the chips (AB8500, AB8505, AB9540) cannot read
the AB8500_REV_REG register but return errors
- Some of them have the same ID value in the hardware
register AB8500_REV_REV, for example the first versions
of AB8505 and AB9540 have 0xFF in this register -
just like the AB8500.
So we need to be able to enforce a certain version from
the platform. We do this by using the id of the platform
device that provides the read/write functions.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We were not freeing the irq properly in the error path in
the AB8500 driver.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The jack detection on WM1811 is often required during system suspend, add
it as another check when deciding if we should suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the default state that the runtime PM infrastructure expects so
instead just kick the runtime PM core to suspend us if we're not doing
anything (as is default).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The gpio_to_irq() macro is now defined as __gpio_to_irq() instead of IRQ_GPIO().
The __gpio_to_irq() function returns -ENXIO if the referenced gpio_chip
structure does not define a to_irq() member.
This is true of the asic3 gpio_chip structure, and thus calls to gpio_to_irq()
now fail (for example from the gpio-vbus module).
This patch defines the to_irq() member in the asic3 gpio_chip structure.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As 'make versioncheck' points out, there's no need for
drivers/mfd/ab5500-core.c to #include <linux/version.h>, so this patch
removes the unneeded include.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adds support for boards which have an STMPE GPIO device without the
interrupt pin connected. This means that no interrupt can be received
but the GPIO pins can still be driven and read.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adds support for boards which have an STMPE device without the
interrupt pin connected.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implementing irq_set_wake() so that device should able
to wakeup the system through different interrupt provided
by this device like gpios, onkey, rtc etc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are many samsung mfd devices.
The s5m core driver try to support various samsung s5m series.
It will cover S5M8767A and S5M8763 and S5M8751.
This patch is enable to support various s5m series.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_base of the tps65910 irq platform data should be
initialized with the board provided irq_base data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If device type is not supported in driver, have to retun error.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove "wm8350->irq_base = pdata->irq_base" to avoid
null pointer exception and wm8350->irq_base got from
irq_alloc_descs().
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds an initial PRCMU register access API, which
for now should only be used for a very limited set of registers.
The idea about this API is that we split the PRCMU driver in
one part that deals with interaction with the PRCMU firmware
and one part that simply provide write accessors in the PRCMU
register range. The latter are just a collection of registers
exposed in the PRCMU register range for various purposes and
not related to the PRCMU firmware.
Currently we support some limited GPIO, SPI and UART settings
through this API.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In prcmu firmware version 3.4.4 the issue with longer
intervalls than 131 s was fixed, we don't expect the
issue to creep back up.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This updates the operating point handling code by:
- Supporting the DDR OPP retention state.
- Supporting another low operating point named
APE_50_PARTLY_25_OPP
- Adding an interface to figure out if the sleep state change
was properly achieved.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As drivers have progressed and got some more review we have
consequently moved things around:
- Some device drivers have changed name and some were wrong
from the beginning.
- We removed the dependency from some domains to the VAPE
domain - SIA MMDSP, SIA PIPE, SVA MMDSP and SVA PIPE power
domains are handled outside the framework while ESRAM12
and ESRAM34 are actually handled inside the PRCMU.
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This updates the clock handling in the DB8500 PRCMU driver with
the latest findings and API changes related to changes in the
backing firmware in the PRCMU.
- Add the necessary interfaces to get the frequencies of the
clocks and set the rate of some of the clocks.
- Add support for controlling the clocks PLLSOC0, PLLDSI,
DSI0, DSI1 and DSI escape clocks (DSInESCCLK).
- Correct the PLLSDI enable/disable sequence by using the
DSIPLL_CLAMPI bit.
After this we will have the interfaces and code to implement the
U8500 clock framework properly.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This prefixes a number of accessor functions with db8500_* since
they are DB8500-specific and we need to move to this naming
scheme.
We also replace numerous instances of machine_is() with cpu_is()
which covers the right type of ASICs rather than entire machines
i.e. boards.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch exports a function that can be used to tell which
version of the DB8500 PRCMU firmware is available, and revamps the
firmware detection code a bit.
Reviewed-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This removes the U8400 legacy from PRCMU and cpufreq drivers.
This platform has no current in-kernel users.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add __devinit annotation for da9052_spi_probe to fix below build warning:
WARNING: drivers/built-in.o(.text+0x349b4): Section mismatch in reference from the function da9052_spi_probe() to the function .devinit.text:da9052_device_init()
The function da9052_spi_probe() references
the function __devinit da9052_device_init().
This is often because da9052_spi_probe lacks a __devinit
annotation or the annotation of da9052_device_init is wrong.
Also add __devexit annotation for da9052_spi_remove because we have
__devexit_p around it in the remove callback.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MC13783 can be programmed to wait some clock cycles between the
touchscreen polarization and the resistance conversion. This is
needed to adjust for touchscreens with high capacitance between
plates.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TPS65217 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators
- White LED
- USB battery charger
This patch adds support for tps65217 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This has been deprecated for considerable time now and support has been
removed from the regulator API. dev_name should be used instead.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Axel Lin