Fix a conditional statement checking for NULL in both
ds1685_rtc_sysfs_time_regs_show and ds1685_rtc_sysfs_time_regs_store
that was using a logical AND when it should be using a logical OR so
that we fail out of the function properly if the condition ever
evaluates to true.
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_read_alarm':
drivers/rtc/rtc-ds1685.c:402: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:409: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:416: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c: In function `ds1685_rtc_set_alarm':
drivers/rtc/rtc-ds1685.c:475: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:478: warning: comparison is always true due to limited range of data type
drivers/rtc/rtc-ds1685.c:481: warning: comparison is always true due to limited range of data type
u8 cannot contain a value larger than 0xff, hence drop the checks.
Wrapping the checks in unlikely() indicated some sense of humor, though ;-)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The newly added ds1685 driver causes a build error when enabled without
CONFIG_RTC_INTF_DEV:
drivers/rtc/rtc-ds1685.c:919:22: error: 'ds1685_rtc_alarm_irq_enable' undeclared here (not in a function)
.alarm_irq_enable = ds1685_rtc_alarm_irq_enable,
Apparently the driver was incorrectly changed to reflect the interface
change from 16380c153a ("RTC: Convert rtc drivers to use the
alarm_irq_enable method"), which removed the respective #ifdef from all
other rtc drivers.
This does the same change that was merged for the other drivers before and
removes the #ifdef, allowing the interrupts to be enabled through the
in-kernel rtc interface independent of the existence of /dev/rtc.
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add additional flag to read in async mode. In this mode the caller will get
reply via registered callback for capture_sample. Callbacks can be registered
using sensor_hub_register_callback function. The usage id parameter of the
capture_sample can be matched with the usage id of the requested attribute.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
This adds a driver for the Dallas/Maxim DS1685-family of RTC chips. It
supports the DS1685/DS1687, DS1688/DS1691, DS1689/DS1693, DS17285/DS17287,
DS17485/DS17487, and DS17885/DS17887 RTC chips. These chips are commonly
found in SGI O2 and SGI Octane systems. It was originally derived from a
driver patch submitted by Matthias Fuchs many years ago for use in
EPPC-405-UC modules, which also used these RTCs. In addition to the
time-keeping functions, this RTC also handles the shutdown mechanism of
the O2 and Octane and acts as a partial NVRAM for the boot PROMS in these
systems.
Verified on both an SGI O2 and an SGI Octane.
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version). The old compatible string is kept for backward compatibility.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new mvebu SoCs come with a new RTC driver. This patch adds the
support for this new IP which is currently found in the Armada 38x
SoCs.
This RTC provides two alarms, but only the first one is used in the
driver. The RTC also allows using periodic interrupts.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Abracon AB-RTCMC-32.768kHz-B5ZE-S3 alarm is only accurate to the minute.
For that reason, UIE mode is currently not supported by the driver. But
the device provides a watchdog timer which can be coupled with the alarm
mechanism to extend support and provide sub-minute alarm capability.
This patch implements that extension. More precisely, it makes use of the
watchdog timer for alarms which are less that four minutes in the future
(with second accuracy) and use standard alarm mechanism for other alarms
(with minute accuracy).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for Abracon AB-RTCMC-32.768kHz-B5ZE-S3
RTC/Calendar module w/ I2C interface.
This support includes RTC time reading and setting, Alarm (1 minute
accuracy) reading and setting, and battery low detection. The device also
supports frequency adjustment and two timers but those features are
currently not implemented in this driver. Due to alarm accuracy
limitation (and current lack of timer support in the driver), UIE mode is
not supported.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After we set the GET_TIME bit, the rtc time can't be read immediately. We
should wait up to 31.25 us, about one cycle of 32khz. Otherwise reading
RTC time will return a old time. If we clear the GET_TIME bit after
setting, the time of i2c transfer is certainly more than 31.25us.
Doug said:
: I think we are safe. At 400kHz (the max speed of this part) each bit can
: be transferred no faster than 2.5us. In order to do a valid i2c
: transaction we need to _at least_ write the address of the device and the
: data onto the bus, which is 16 bits. 16 * 2.5us = 40us. That's above the
: 31.25us
[akpm@linux-foundation.org: tweak comment per review discussion]
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Cc: Heiko Stübner <heiko@sntech.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intended for monitoring and controlling the security features. These bits
are required to bring this unit back to live after a security violation
event was detected. The code to bring it back to live will follow after a
vendor clearance.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current in-tree users of ISL12057 RTC chip (NETGEAR ReadyNAS 102, 104 and
2120) do not have the IRQ#2 pin of the chip (associated w/ the Alarm1
mechanism) connected to their SoC, but to a PMIC (TPS65251 FWIW). This
specific hardware configuration allows the NAS to wake up when the alarms
rings.
Recently introduced alarm support for ISL12057 relies on the provision of
an "interrupts" property in system .dts file, which previous three users
will never get. For that reason, alarm support on those devices is not
function. To support this use case, this patch adds a new DT property for
ISL12057 (isil,irq2-can-wakeup-machine) to indicate that the chip is
capable of waking up the device using its IRQ#2 pin (even though it does
not have its IRQ#2 pin connected directly to the SoC).
This specific configuration was tested on a ReadyNAS 102 by setting an
alarm, powering off the device and see it reboot as expected when the
alarm rang w/:
# echo `date '+%s' -d '+ 1 minutes'` > /sys/class/rtc/rtc0/wakealarm
# shutdown -h now
As a side note, the ISL12057 remains in the list of trivial devices,
because the property is not per se required by the device to work but can
help handle system w/ specific requirements. In exchange, the new feature
is described in details in a specific documentation file.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds alarm support to Intersil ISL12057 driver. This allows to
configure the chip to generate an interrupt when the alarm matches current
time value. Alarm can be programmed up to one month in the future and is
accurate to the second.
The patch was developed to support two different configurations: systems
w/ and w/o RTC chip IRQ line connected to the main CPU.
The latter is the one found on current 3 kernel users of the chip for
which support was initially developed (Netgear ReadyNAS 102, 104 and 2120
NAS). On those devices, the IRQ#2 pin of the chip is not connected to the
SoC but to a PMIC. This allows setting an alarm, powering off the device
and have it wake up when the alarm rings. To support that configuration
the driver does the following:
1. it has alarm_irq_enable() function returns -ENOTTY when no IRQ
is passed to the driver.
2. it marks the device as a wakeup source in all cases (whether an
IRQ is passed to the driver or not) to have 'wakealarm' sysfs
entry created.
3. it marks the device has not supporting UIE mode when no IRQ is
passed to the driver (see the commmit message of c9f5c7e7a8)
This specific configuration was tested on a ReadyNAS 102 by setting an
alarm, powering off the device and see it reboot as expected when the
alarm rang.
The former configuration was tested on a Netgear ReadyNAS 102 after some
soldering of the IRQ#2 pin of the RTC chip to a MPP line of the SoC (the
one used usually handles the reset button). The test was performed using
a modified .dts file reflecting this change (see below) and rtc-test.c
program available in Documentation/rtc.txt. This test program ran as
expected, which validates alarm supports, including interrupt support.
As a side note, the ISL12057 remains in the list of trivial devices, i.e.
no specific DT binding being added by this patch: i2c core automatically
handles extraction of IRQ line info from .dts file. For instance, if one
wants to reference the interrupt line for the alarm in its .dts file,
adding interrupt and interrupt-parent properties works as expected:
isl12057: isl12057@68 {
compatible =3D "isil,isl12057";
interrupt-parent =3D <&gpio0>;
interrupts =3D <6 IRQ_TYPE_EDGE_FALLING>;
reg =3D <0x68>;
};
FWIW, if someone is looking for a way to test alarm support on a system on
which the chip IRQ line has the ability to boot the system (e.g. ReadyNAS
102, 104, etc):
# echo 0 > /sys/class/rtc/rtc0/wakealarm
# echo `date '+%s' -d '+ 1 minutes'` > /sys/class/rtc/rtc0/wakealarm
# shutdown -h now
With the commands above, after a minute, the system comes back to life.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull EFI updates from Ingo Molnar:
"Main changes:
- Move efivarfs from the misc filesystem section to pseudo filesystem
- Expose firmware platform size in sysfs
- Improve robustness of get_memory_map() by removing assumptions on
the size of efi_memory_desc_t.
- various cleanups and fixes
The biggest risk is the get_memory_map() change, which changes the way
that both the arm64 and x86 EFI boot stub build the early memory map.
There are no known regressions with it at the moment, BYMMV"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Don't look for chosen@0 node on DT platforms
firmware: efi: Remove unneeded guid unparse
efi/libstub: Call get_memory_map() to obtain map and desc sizes
efi: Small leak on error in runtime map code
efi: rtc-efi: Mark UIE as unsupported
arm64/efi: efistub: Apply __init annotation
efi: Expose underlying UEFI firmware platform size to userland
efi: Rename efi_guid_unparse to efi_guid_to_str
efi: Update the URLs for efibootmgr
fs: Make efivarfs a pseudo filesystem, built by default with EFI
Pull timer updates from Ingo Molnar:
"The main changes in this cycle were:
- rework hrtimer expiry calculation in hrtimer_interrupt(): the
previous code had a subtle bug where expiry caching would miss an
expiry, resulting in occasional bogus (late) expiry of hrtimers.
- continuing Y2038 fixes
- ktime division optimization
- misc smaller fixes and cleanups"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hrtimer: Make __hrtimer_get_next_event() static
rtc: Convert rtc_set_ntp_time() to use timespec64
rtc: Remove redundant rtc_valid_tm() from rtc_hctosys()
rtc: Modify rtc_hctosys() to address y2038 issues
rtc: Update rtc-dev to use y2038-safe time interfaces
rtc: Update interface.c to use y2038-safe time interfaces
time: Expose get_monotonic_boottime64 for in-kernel use
time: Expose getboottime64 for in-kernel uses
ktime: Optimize ktime_divns for constant divisors
hrtimer: Prevent stale expiry time in hrtimer_interrupt()
ktime.h: Introduce ktime_ms_delta
since that's a more logical and accurate place - Leif Lindholm
* Update efibootmgr URL in Kconfig help - Peter Jones
* Improve accuracy of EFI guid function names - Borislav Petkov
* Expose firmware platform size in sysfs for the benefit of EFI boot
loader installers and other utilities - Steve McIntyre
* Cleanup __init annotations for arm64/efi code - Ard Biesheuvel
* Mark the UIE as unsupported for rtc-efi - Ard Biesheuvel
* Fix memory leak in error code path of runtime map code - Dan Carpenter
* Improve robustness of get_memory_map() by removing assumptions on the
size of efi_memory_desc_t (which could change in future spec
versions) and querying the firmware instead of guessing about the
memmap size - Ard Biesheuvel
* Remove superfluous guid unparse calls - Ivan Khoronzhuk
* Delete unnecessary chosen@0 DT node FDT code since was duplicated
from code in drivers/of and is entirely unnecessary - Leif Lindholm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iPpM
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI updates from Matt Fleming:
" - Move efivarfs from the misc filesystem section to pseudo filesystem,
since that's a more logical and accurate place - Leif Lindholm
- Update efibootmgr URL in Kconfig help - Peter Jones
- Improve accuracy of EFI guid function names - Borislav Petkov
- Expose firmware platform size in sysfs for the benefit of EFI boot
loader installers and other utilities - Steve McIntyre
- Cleanup __init annotations for arm64/efi code - Ard Biesheuvel
- Mark the UIE as unsupported for rtc-efi - Ard Biesheuvel
- Fix memory leak in error code path of runtime map code - Dan Carpenter
- Improve robustness of get_memory_map() by removing assumptions on the
size of efi_memory_desc_t (which could change in future spec
versions) and querying the firmware instead of guessing about the
memmap size - Ard Biesheuvel
- Remove superfluous guid unparse calls - Ivan Khoronzhuk
- Delete unnecessary chosen@0 DT node FDT code since was duplicated
from code in drivers/of and is entirely unnecessary - Leif Lindholm
There's nothing super scary, mainly cleanups, and a merge from Ricardo who
kindly picked up some patches from the linux-efi mailing list while I
was out on annual leave in December.
Perhaps the biggest risk is the get_memory_map() change from Ard, which
changes the way that both the arm64 and x86 EFI boot stub build the
early memory map. It would be good to have it bake in linux-next for a
while.
"
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Array of platform_device_id elements should be terminated with empty
element.
Fixes: 5bccae6ec4 ("rtc: s5m-rtc: add real-time clock driver for s5m8767")
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc_set_ntp_time() uses timespec which is y2038-unsafe,
so modify to use timespec64 which is y2038-safe, then
replace rtc_time_to_tm() with rtc_time64_to_tm().
Also adjust all its call sites(only NTP uses it) accordingly.
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
rtc_read_time() has already judged valid tm by rtc_valid_tm(),
so just remove it.
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
rtc_hctosys() has a number of y2038 issues.
This patch resolves them by:
- Replace rtc_tm_to_time() with y2038-safe rtc_tm_to_time64()
- Replace do_settimeofday() with y2038-safe do_settimeofday64()
After this patch, it should not have any remaining y2038 issues.
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, rtc-dev.c uses y2038 problematic rtc_tm_to_time()
and rtc_time_to_tm(). So replace them with their corresponding
y2038-safe versions: rtc_tm_to_time64() and rtc_time64_to_tm().
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Currently, interface.c uses y2038 problematic rtc_tm_to_time()
and rtc_time_to_tm(). So replace them with their corresponding
y2038-safe versions: rtc_tm_to_time64() and rtc_time64_to_tm().
Cc: pang.xunlei <pang.xunlei@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tools like hwclock attempt to enable the RTC update interrupt (UIE) to
maximize the accuracy of the reported time value. The EFI rtc does not
have interrupt capability so this is a pointless exercise to begin with,
but the generic RTC framework ends up issuing a SetWakeupTime() Runtime
Services call before drawing that conclusion on its own.
Instead, we can mark UIE as unsupported at driver probe time. The net
result is the same, but without the spurious SetWakeupTime() call.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
As we removed all the !DT boards during 3.19 cycle, we can now remove these
options.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Support for keyword 'boolean' will be dropped later on.
No functional change.
Reference: http://lkml.kernel.org/r/cover.1418003065.git.cj@linux.com
Signed-off-by: Christoph Jaeger <cj@linux.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Commit 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
replaces SIMPLE_DEV_PM_OPS with direct declaration of snvs_rtc_pm_ops,
but does so outside #ifdef CONFIG_PM_SLEEP. This causes the driver
build to fail if CONFIG_PM_SLEEP is not configured.
Fixes: 7654e9d4fd ("drivers/rtc/rtc-snvs: fix suspend/resume")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some nice cleanups like removing bootmem, and removal of __get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP implementation, but is
only used by us and arm(64). We have an ack from Steve Capper, and although we
didn't get an ack from Andrew he told us to take the patch through the powerpc
tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was happy for
us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL. That patch
also appears in Corey Minyard's IPMI tree, you may see a conflict there.
There is also an RTC driver for OPAL. We weren't able to get any response from
the RTC maintainer, Alessandro Zummo, so in the end we just merged the driver.
The usual batch of Freescale updates from Scott.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jvyT
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
"Some nice cleanups like removing bootmem, and removal of
__get_cpu_var().
There is one patch to mm/gup.c. This is the generic GUP
implementation, but is only used by us and arm(64). We have an ack
from Steve Capper, and although we didn't get an ack from Andrew he
told us to take the patch through the powerpc tree.
There's one cxl patch. This is in drivers/misc, but Greg said he was
happy for us to manage fixes for it.
There is an infrastructure patch to support an IPMI driver for OPAL.
There is also an RTC driver for OPAL. We weren't able to get any
response from the RTC maintainer, Alessandro Zummo, so in the end we
just merged the driver.
The usual batch of Freescale updates from Scott"
* tag 'powerpc-3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (101 commits)
powerpc/powernv: Return to cpu offline loop when finished in KVM guest
powerpc/book3s: Fix partial invalidation of TLBs in MCE code.
powerpc/mm: don't do tlbie for updatepp request with NO HPTE fault
powerpc/xmon: Cleanup the breakpoint flags
powerpc/xmon: Enable HW instruction breakpoint on POWER8
powerpc/mm/thp: Use tlbiel if possible
powerpc/mm/thp: Remove code duplication
powerpc/mm/hugetlb: Sanity check gigantic hugepage count
powerpc/oprofile: Disable pagefaults during user stack read
powerpc/mm: Check for matching hpte without taking hpte lock
powerpc: Drop useless warning in eeh_init()
powerpc/powernv: Cleanup unused MCE definitions/declarations.
powerpc/eeh: Dump PHB diag-data early
powerpc/eeh: Recover EEH error on ownership change for BCM5719
powerpc/eeh: Set EEH_PE_RESET on PE reset
powerpc/eeh: Refactor eeh_reset_pe()
powerpc: Remove more traces of bootmem
powerpc/pseries: Initialise nvram_pstore_info's buf_lock
cxl: Name interrupts in /proc/interrupt
cxl: Return error to PSL if IRQ demultiplexing fails & print clearer warning
...
rtc_timer_do_work() only judges -ETIME failure of__rtc_set_alarm(), but
doesn't handle other failures like -EIO, -EBUSY, etc.
If there is a failure other than -ETIME, the next rtc_timer will stay in
the timerqueue. Then later rtc_timers will be enqueued directly because
they have a later expires time, so the alarm irq will never be programmed.
When such failures happen, this patch will retry __rtc_set_alarm(), if
still can't program the alarm time, it will remove current rtc_timer from
timerqueue and fetch next one, thus preventing it from affecting other rtc
timers.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, ab8500 doesn't set uie_unsupported of rtc_device, while it
doesn't support UIE, see ab8500_rtc_set_alarm().
Thus, when going through rtc_update_irq_enable()->rtc_timer_enqueue(),
there's a chance it has an alarm timer1 queued before which is going to
fired, so this update timer2 will be queued because it isn't the leftmost
one, which means rtc_timer_enqueue() will return 0.
This will result in two problems:
1) UIE EMUL will not be used.
2) When the alarm timer1 is fired, in rtc_timer_do_work() timer2 will
fail to set the alarm time, so this rtc will disfunctional due to
timer2 with the earliest expires in the timerqueue.
So, rtc drivers must set this flag if they don't support UIE.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alarm interrupt handler also reads registers which are part of SNVS
and need clocks enabled. However, the resume function is called after
IRQ's have been enabled, hence this leads to a abort:
Unhandled fault: external abort on non-linefetch (0x1008) at 0x908c604c
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 421 Comm: sh Not tainted 3.18.0-rc5-00135-g0689c67-dirty #1592
task: 8e03e800 ti: 8cad8000 task.ti: 8cad8000
PC is at snvs_rtc_irq_handler+0x14/0x74
LR is at handle_irq_event_percpu+0x3c/0x144
Fix this by using the .{suspend/resume}_noirq callbacks instead of
.{suspend/resume} .
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add clock enable and disable support for the SNVS peripheral, which is
required for using the RTC within the SNVS block.
The clock is not strictly enforced, as this would break the i.MX devices.
The clocking for the i.MX devices seems to be enabled elsewhere and
enabling RTC SNVS for Vybrid results in a crash. This patch adds the
clock support but also makes it optional so Vybrid platform can use the
clock if defined while making sure not to break i.MX.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.
It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.
Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Mark, it is generally useful to log the error code when
reporting a failure. This patch improves existing calls to dev_err() in
ISL12057 driver to also report error code.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Suggested-by: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As suggested by Uwe, instead of clearing oscillator failure bit
unconditionally at driver load, this patch adds proper handling of the
flag. The driver now returns -ENODATA when reading time from the device
and oscillator failure bit is set. The flag is now cleared only when the
a new time value is pushed to the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The month register of ISL12057 RTC chip includes a century bit which
reports overflow of year register from 99 to 0. This bit can also be
written, which allows using it to extend the time interval the chip can
support from 99 to 199 years.
This patch adds support for century overflow bit in tm to regs and regs to
tm helpers in ISL12057 driver.
This was tested by putting a device 100 years in the future (using a
specific kernel due to the inability of userland tools such as date or
hwclock to pass year 2038), rebooting on a kernel w/ this patch applied
and verifying the device was still 100 years in the future.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Suggested-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When Intersil ISL12057 support was added by commit 70e123373c ("rtc: Add
support for Intersil ISL12057 I2C RTC chip"), two masks for time registers
values imported from the device were either wrong or omitted, leading to
additional bits from those registers to impact read values:
- mask for hour register value when reading it in AM/PM mode. As
AM/PM mode is not the usual mode used by the driver, this error
would only have an impact on an externally configured RTC hour
later read by the driver.
- mask for month value. The lack of masking would provide an
erroneous value if century bit is set.
This patch fixes those two masks.
Fixes: 70e123373c ("rtc: Add support for Intersil ISL12057 I2C RTC chip")
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MCP7940x is same RTC as MCP7941x. The difference is that MCP7941x chips
contain additional EEPROM on a different i2c address.
DS1307 driver already supports MCP7941x, so just add a new i2c device id
and rename functions and defines accordingly.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the watchdog functionality of the DS1374 rtc. Based on
the m41t80 watchdog functionality Note: watchdog uses the same registers
as alarm.
[akpm@linux-foundation.org: don't forget mutex_unlock() in ds1374_wdt_open() error path]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Soeren Andersen <san@rosetechnology.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: hao liu <hao.liu@csr.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case the card is woken up of the rtc alarm, the
devm_rtc_device_register function detects it as a pending alarm about a
month in the future. Fix this by clearing the alarm in module probe.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Haoyu hym8563 datasheet this saves som power. Might be
importat to battery life. And maybe it works for the NXP part as well.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To guarantee that a set alarm occurs in the future, the set alarm time
is rounded up to the nearest minute. Also we cannot handle UIE as it
requires second precision.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Incorrect mask was used for hour and monthday fields.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The NXP datasheet says:
"Bits labeled as N should always be written with logic 0."
At least one of those bits is sometime read as a 1, therfore violating
this rule. To fix this we mask away those bits.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some code that was left from before block read/write was used.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix minor coding style issues like comment style, indentation and remove
a few unnecessary casts.
Also drop the 1 from OMAP1 in the driver description.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ALARM interrupt must not be disabled during shutdown in order to be
able to power up the system using an RTC alarm.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new property "ti,system-power-controller" to register the RTC as a
power-off handler.
Some RTC IP revisions can control an external PMIC via the pmic_power_en
pin, which can be configured to transition to OFF on ALARM2 events and
back to ON on subsequent ALARM (wakealarm) events.
This is based on earlier work by Colin Foe-Parker and AnilKumar Ch. [1]
[1] https://www.mail-archive.com/linux-omap@vger.kernel.org/msg82127.html
[akpm@linux-foundation.org: add comment]
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Colin Foe-Parker <colin.foeparker@logicpd.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add helper to read raw BCD time that can be used in interrupt context.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some legacy RTC IP revisions has a power-up reset flag in the status
register that later revisions lack.
As this flag is always read back as set on later revisions (or is
overloaded with a different flag), make sure to only clear the flag and
print the info message on legacy platforms.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove DRIVER_NAME macro which was used for unrelated strings (e.g.
id-table entry and module name), but not for related ones (e.g. module
name and alias).
Also move the module alias to the other module-info entries.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add struct omap_rtc to hold previously global data as well as the
IP-block feature flags.
Also convert the register-access macros to proper inline helper functions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure not to register the class device until after the device has
been configured.
Currently, the device is not fully configured (e.g. 24-hour mode) when
the class device is registered, something which involves driver
callbacks for example to read the current time.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some debug messages and return errors from subsystems rather than
always fail with -EIO.
Note that the class-registration error has already been logged by rtc
core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use writel instead of writeb when disabling interrupts at probe as
ALARM2 is not cleared otherwise on some IP-block revisions (e.g.
AM3352).
Note that the driver currently never enables the ALARM2 interrupt.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The platform device must be registered as wakeup capable before
registering the class device, or the wakealarm attribute will not be
created.
Also make sure to unregister the wakeup source on probe errors.
Fixes: 1d2e2b65d0 ("rtc: omap: restore back (hard-code) wakeup support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series fixes a few issues with the omap rtc-driver, cleans up a
bit, adds device abstraction, and finally adds support for the PMIC
control feature found in some revisions of this RTC IP block.
Ultimately, this allows for powering off the Beaglebone and waking it up
again on RTC alarms.
This patch (of 20):
Make sure not to reset the clock-source configuration when enabling the
32kHz clock mux.
Until the clock source can be configured through device tree we must not
overwrite settings made by the bootloader (e.g. clock-source
selection).
Fixes: cd914bba03 ("drivers/rtc/rtc-omap.c: add support for enabling 32khz clock")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Keerthy J <j-keerthy@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some rtc devices always return '0' when rtc_class_ops.read_time is
called. So if rtc_time isn't verified in callback, rtc interface cannot
know whether rtc_time is valid.
Check rtc_time by using 'rtc_valid_tm' in '__rtc_read_time'. And add
the message for debugging.
Signed-off-by: Hyogi Gim <hyogi.gim@lge.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move rtc register to be later than hardware initialization. The reason
is that devm_rtc_device_register() will do read_time() which is a
callback accessing hardware. This sometimes causes a hang in the
hardware related callback.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer core updates from Thomas Gleixner:
"The time(r) departement provides:
- more infrastructure work on the year 2038 issue
- a few fixes in the Armada SoC timers
- the usual pile of fixlets and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Use the reference clock on A375 SoC
watchdog: orion: Use the reference clock on Armada 375 SoC
clocksource: armada-370-xp: Add missing clock enable
time: Fix sign bug in NTP mult overflow warning
time: Remove timekeeping_inject_sleeptime()
rtc: Update suspend/resume timing to use 64bit time
rtc/lib: Provide y2038 safe rtc_tm_to_time()/rtc_time_to_tm() replacement
time: Fixup comments to reflect usage of timespec64
time: Expose get_monotonic_coarse64() for in-kernel uses
time: Expose getrawmonotonic64 for in-kernel uses
time: Provide y2038 safe mktime() replacement
time: Provide y2038 safe timekeeping_inject_sleeptime() replacement
time: Provide y2038 safe do_settimeofday() replacement
time: Complete NTP adjustment threshold judging conditions
time: Avoid possible NTP adjustment mult overflow.
time: Rename udelay_test.c to test_udelay.c
clocksource: sirf: Remove hard-coded clock rate
The at91 cleanups changed a lot of files, this merges in the
latest cleanups to resolve the conflicts
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/clock.c
arch/arm/mach-at91/clock.h
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Currently the rtc suspend/resume timing is done using
y2038 problematic timespecs. So update the code to utilize
timespec64 types.
Signed-off-by: John Stultz <john.stultz@linaro.org>
As part of addressing "y2038 problem" for in-kernel uses, this patch
adds safe rtc_tm_to_time64()/rtc_time64_to_tm() respectively using
time64_t.
After this patch, rtc_tm_to_time() is deprecated and all its call
sites will be fixed using corresponding safe versions, it can be
removed when having no users. Also change rtc_tm_to_time64() to
return time64_t directly instead of just as a parameter like
rtc_tm_to_time() does.
After this patch, rtc_time_to_tm() is deprecated and all its call
sites will be fixed using corresponding safe versions, it can be
removed when having no users.
In addition, change rtc_tm_to_ktime() and rtc_ktime_to_tm() to use
the safe version in passing.
Signed-off-by: pang.xunlei <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This resolves some of the obvious conflicts between the at91 cleanup and
drivers branches.
Conflicts:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
drivers/rtc/Kconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It is only about a not so recent driver for old platforms: RTT as RTC driver:
- RTT as RTC driver enhancements and machine specific include files removal
- RTT as RTC driver conversion to device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUZg/EAAoJEAf03oE53VmQ/KAIAJi5Ky2ekaZ4FGWbDrnQBHV+
X0M/wvCdHw4D7VENo1W3U3ulf5r0XimeY6nnbmx3Ki0fTE2O3VyfLNzkjQtMf6iX
TfoJM9y4fWsY5AXnynYO1Gj/2CH6Xab79Kb5sxL8b9VvlUMxlsKoQOmUYHC775OX
YiBfp3dZYODkMyIIQmSkoZGj+kkgWbjMrp9CPueqVltha/EbfBP96Kib2G/aJVkb
F9QyOq8B/mpUk2P29L1hc9X0/tjwaLZsO97zzhYVj7VwZS9sbYztQgmUNdtEds4/
7EhMwSXxb9L5LkuoyuHFpRLMGzLrN9XBftE58s92hXwnM2KZE4eNo/JF0SGDOKo=
=POJG
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/drivers
Pull "First batch of drivers for 3.19" from Nicolas Ferre:
It is only about a not so recent driver for old platforms: RTT as RTC driver:
- RTT as RTC driver enhancements and machine specific include files removal
- RTT as RTC driver conversion to device tree
* tag 'at91-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
rtc: at91sam9: add DT bindings documentation
rtc: at91sam9: use clk API instead of relying on AT91_SLOW_CLOCK
ARM: at91: add clk_lookup entry for RTT devices
rtc: at91sam9: rework the Kconfig description
rtc: at91sam9: make use of syscon/regmap to access GPBR registers
rtc: at91sam9: add DT support
rtc: at91sam9: replace devm_ioremap by devm_ioremap_resource
rtc: at91sam9: use standard readl/writel functions instead of raw versions
rtc: at91sam9: remove references to mach specific headers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When removing old board !DT support, several Kconfig options were deleted.
Propagate this removal to drivers Kconfig files.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The patch implements the OPAL rtc driver that binds with the rtc
driver subsystem. The driver uses the platform device infrastructure
to probe the rtc device and register it to rtc class framework. The
'wakeup' is supported depending upon the property 'has-tpo' present
in the OF node. It provides a way to load the generic rtc driver in
in the absence of an OPAL driver.
The patch also moves the existing OPAL rtc get/set time interfaces to the
new driver and exposes the necessary OPAL calls using EXPORT_SYMBOL_GPL.
Test results:
-------------
Host:
[root@tul169p1 ~]# ls -l /sys/class/rtc/
total 0
lrwxrwxrwx 1 root root 0 Oct 14 03:07 rtc0 -> ../../devices/opal-rtc/rtc/rtc0
[root@tul169p1 ~]# cat /sys/devices/opal-rtc/rtc/rtc0/time
08:10:07
[root@tul169p1 ~]# echo `date '+%s' -d '+ 2 minutes'` > /sys/class/rtc/rtc0/wakealarm
[root@tul169p1 ~]# cat /sys/class/rtc/rtc0/wakealarm
1413274345
[root@tul169p1 ~]#
FSP:
$ smgr mfgState
standby
$ rtim timeofday
System time is valid: 2014/10/14 08:12:04.225115
$ smgr mfgState
ipling
$
CC: devicetree@vger.kernel.org
CC: tglx@linutronix.de
CC: rtc-linux@googlegroups.com
CC: a.zummo@towertech.it
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The RTT block is using the slow clock which is accessible through the clk
API.
Use the clk API to retrieve, enable and get the slow clk rate instead of
the AT91_SLOW_CLOCK macro (which hardcodes the slow clk rate).
Doing this allows us to reference the clk thus preventing the CCF from
disabling it during the "disable unused" phase.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove all references to AT91CAP9 SoC which has been removed.
Rework help message to remove any specific references to AT91SAM9 SoCs.
State that RTC_DRV_AT91SAM9_RTT and RTC_DRV_AT91SAM9_GPBR options are only
used when booting non DT boards.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The GPBR registers are not part of the RTT block and thus should not be
defined in the reg property of the rtt node.
Use syscon to provide a proper DT representation and reference the GPBR
syscon device in a new "atmel,rtt-rtc-time-reg" property which store both
the syscon device phandle and the register offset within the GPBR block.
When using non DT boards, we won't be able to retrieve the syscon regmap,
hence we need to create our own regmap using the memory region defined
in the 2nd memory resource assigned to the RTT platform device.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add of_match_table to the existing driver so that rtt nodes defined in at91
DTs can be attached to this driver.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Replace devm_ioremap calls by devm_ioremap_resource which already check
resource consistency (resource != NULL) and print an error in case of
failure.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Raw versions of writel and writel should not be directly used and should
be replaced by their relaxed versions (readl/writel_relaxed), which take
endianness conversion into account.
In this driver we prefer the standard readl/writel function which add the
appropriate memory barrier around the access (the performance penalty is
negligible for this kind of application).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In order to support multi platform kernel drivers should not include
machine specific headers.
Copy RTT macros in the driver code and remove any machine specific
headers.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As there is currently no-one to take care of this old !MMU target and as its
support in recent kernels is a bit rotten, remove this at91x40 support and the
board file associated with it (at91eb01).
There are modern ARM !MMU in Mainline now so this target is not interesting for
building tests anymore. It would be better to start from these modern ARM !MMU
platforms to reintroduce at91x40 support if needed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fix register value in bq32000 trickle charging.
Mike reported that I'm using wrong value in one trickle-charging case,
and after checking docs, I must admit he's right.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Mike Bremford <mike@bfo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unconditional initialization failure on non-exynos3250 SoCs.
Commit df9e26d093 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
introduced rtc source clock support, but also added initialization
failure on SoCs, which doesn't need such clock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds support for RTC device inside PM8941 PMIC. The RTC in this PMIC
have two register spaces. Thus the rtc-pm8xxx is slightly reworked to
reflect these differences.
The register set for different PMIC chips are selected on DT compatible
string base.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: simplify and fix locking in pm8xxx_rtc_set_time()]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 EFI updates from Peter Anvin:
"This patchset falls under the "maintainers that grovel" clause in the
v3.18-rc1 announcement. We had intended to push it late in the merge
window since we got it into the -tip tree relatively late.
Many of these are relatively simple things, but there are a couple of
key bits, especially Ard's and Matt's patches"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rtc: Disable EFI rtc for x86
efi: rtc-efi: Export platform:rtc-efi as module alias
efi: Delete the in_nmi() conditional runtime locking
efi: Provide a non-blocking SetVariable() operation
x86/efi: Adding efi_printks on memory allocationa and pci.reads
x86/efi: Mark initialization code as such
x86/efi: Update comment regarding required phys mapped EFI services
x86/efi: Unexport add_efi_memmap variable
x86/efi: Remove unused efi_call* macros
efi: Resolve some shadow warnings
arm64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
ia64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
x86: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
efi: Introduce efi_md_typeattr_format()
efi: Add macro for EFI_MEMORY_UCE memory attribute
x86/efi: Clear EFI_RUNTIME_SERVICES if failing to enter virtual mode
arm64/efi: Do not enter virtual mode if booting with efi=noruntime or noefi
arm64/efi: uefi_init error handling fix
efi: Add kernel param efi=noruntime
lib: Add a generic cmdline parse function parse_option_str
...
Commit b5ada4600d ("drivers/rtc/rtc-cmos.c: fix compilation warning
when !CONFIG_PM_SLEEP") broke wakeup from S5 by making cmos_poweroff a
nop unless CONFIG_PM_SLEEP was defined.
Fix this by restricting the #ifdef to cmos_resume and restoring the old
dependency on CONFIG_PM for cmos_suspend and cmos_poweroff.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of pushing each byte let's reduce stack usage by using %*ph specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Sergei Shtylyov, the pcf8563_irq function contains a
bug in the error handling: an interrupt handler is not supposed to
return an errno value but an 'enum irqreturn'.
Let's fix this by returning IRQ_NONE in case of a communication error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-4.9 found a potential condition under which the 'pending' variable
may be used uninitialized:
drivers/rtc/rtc-pcf8563.c: In function 'pcf8563_irq':
drivers/rtc/rtc-pcf8563.c:173:5: warning: 'pending' may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because in the pcf8563_get_alarm_mode() function, we check any
nonzero return of pcf8563_read_block_data, but in the irq function we
only check for negative values, so a possible positive value does not
get detected if the compiler chooses not to inline the entire call
chain.
Checking for any non-zero value in the interrupt handler as well is just
as correct and lets the compiler know what we are doing, without needing
a bogus initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MAX7802 PMIC has a Real-Time-Clock (RTC) with two alarms. This
patch adds support for the RTC and is based on a driver added by Simon
Glass to the Chrome OS kernel 3.8 tree.
[akpm@linux-foundation.org: add comment clarifying ffs() use]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
max77686_rtc_calculate_wday() is used to calculate the day of the week
to be filled in struct rtc_time but that function only calculates the
number of bits shifted. So the ffs() function can be used to find the
first bit set instead of a special function.
[akpm@linux-foundation.org: add comment clarifying ffs() use]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If devm_rtc_device_register() fails a dev_err() is already reported so
there is no need to do an additional dev_info().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The max77686 mfd driver adds a regmap IRQ chip which creates an IRQ
domain that is used to map the virtual RTC alarm1 interrupt.
The RTC driver assumes that this will always be true since the PMIC IRQ
is a required property according to the max77686 DT binding doc. If an
"interrupts" property is not defined for a max77686 PMIC, then the mfd
probe function will fail and the RTC platform driver will never be
probed.
But even when it is not possible to probe the rtc-max77686 driver
without a regmap IRQ chip, it's better to explicitly check if the IRQ
chip data is not NULL and gracefully fail instead of getting an OOPS.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MAX77686 RTC chip has two features called SMPL (Sudden Momentary
Power Loss) and WTSR (Watchdog Timeout and Software Resets). Support
for these features seems to be implemented in the driver but compilation
is disabled using a C pre-processor conditional.
This code has been disabled since the driver was original merged in
commit fca1dd031a ("rtc: max77686: add Maxim 77686 driver").
So, since this code has never been built, let's just remove it.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series add support for the Real Time clock present in the Maxim 77802
Power Managment IC. The version number is quite high because it
previously was part of a bigger series [0] that aimed to add support for
all the devices in the max77802 PMIC. But now that the max77802
dependencies were already merged for 3.17, the series were split but I
kept the version numbering.
While working on the max77802 rtc support a lot of feedback was given and
the issues pointed out also apply to a driver for a similar PMIC RTC
(max77686). So patches 01/06 to 05/06 in the series are cleanups for the
max77686 driver and patch 06/06 adds the support for the max77802 RTC.
The series were tested on an Exynos5250 Snow (max77686) and
Exynos5420 Peach Pit (max77802) machines.
This patch (of 6):
The max77686 includes an RTC that keeps power during suspend. It's
convenient to be able to use it as a wakeup source.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BQ32000 devices have "trickle chargers". Introduce a code to enable the
charger, based on device tree.
Without charger, RTC does not keep time after power off.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Pavel Machek <pavel@denx.de>
Cc: Jason Cooper <jason@lakedameon.net>
Cc: Matti Vaittinen <matti.vaittinen@nsn.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some DS13XX devices have "trickle chargers". Introduce a device tree
binding for specifying the trickle charger configuration for ds1339.
Only ds1339 dt binding is supported because this is the only chip I have.
I _assume_ the code would have worked on other allready supported chips.
However I cannot check the resistor values for the other chips or test
them. For other chips the driver code works as earlier Eg. it does not
check the dt bindings at all
Signed-off-by: Matti Vaittinen <matti.vaittinen@nsn.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the initial version of the RK808 PMIC. This is a power management
IC for multimedia products. It provides regulators that are able to
supply power to processor cores and other components. The chip provides
other modules including RTC, Clockout.
Add RTC driver for supporting RTC device present inside RK808 PMIC.
[akpm@linux-foundation.org: make tm_def static]
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Zhang Qing <zhangqing@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Samuel Ortiz <sameo@linux.intel.com> says:
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dmitry Torokhov <dtor@chromium.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. This allows to
mark all struct of_device_id below drivers/rtc const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for RTC of Exynos3250 SoC. The Exynos3250 needs source
clock(32.768KHz) for RTC block. If source clock of RTC is registerd on
clock list of common clk framework, Exynos RTC drvier have to control
this clock.
Clock list for s3c-rtc device:
- rtc : CLK_RTC of CLK_GATE_IP_PERIR is gate clock for RTC.
- rtc_src : XrtcXTI is 32.768.kHz source clock for RTC.
(XRTCXTI: Specifies a clock from 32.768 kHz crystal pad with XRTCXTI and
XRTCXTO pins. RTC uses this clock as the source of a real-time clock.)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add s3c_rtc_data structure to variant data according to SoC type. The
s3c_rtc_data structure includes some functions to control RTC operation
and specific data dependent on SoC type.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define s3c_rtc structure including necessary variables for S3C RTC device
instead of global variables. This patch improves the readability by
removing global variables.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use c99 initializers for structures.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into drivers
directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=POJD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others,
as well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Smzi
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"These are bug fixes for harmless problems that were not important
enough to get fixed in 3.17. The majority of these are OMAP specific,
but there are also a couple for Marvell mvebu, cns3xxx, and others, as
well as some updates for the MAINTAINERS file.
In particular, Robert Jarzmik and Daniel Mack now volunteered to help
out maintaining the PXA platform, Krzysztof Halasa took over the
cns3xxx platform, Carlo Caione is the maintainer for the new Amlogic
meson platform, and Matthias Brugger is now listed for the mediatek
platform he recently contributed"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: update Shawn's email address
MAINTAINERS: condense some Tegra related entries
MAINTAINERS: add Alexandre Courbot for Tegra
MAINTAINERS: CNS3xxx and IXP4xx update.
MAINTAINERS: Add maintainers entry for Mediatek SoCs
arm, vt8500, LLVMLlinux: Use mcr instead of mcr% for mach-vt8500
MAINTAINERS: add a third maintainer to mach-bcm
CNS3xxx: Fix PCIe read size limit.
CNS3xxx: Fix logical PCIe topology.
CNS3xxx: Fix debug UART.
MAINTAINERS: Add entry for the Amlogic MesonX SoCs
MAINTAINERS: update ARM pxa maintainers
ARM: at91/PMC: don't forget to write PMC_PCDR register to disable clocks
ARM: at91: fix at91sam9263ek DT mmc pinmuxing settings
ARM: mvebu: Netgear RN102: Use Hardware BCH ECC
ARM: Kirkwood: Fix DT based DSA.
ARM: OMAP2+: make of_device_ids const
ARM: omap2: make arrays containing machine compatible strings const
ARM: LPC32xx: Fix reset function
ARM: mvebu: Netgear RN2120: Use Hardware BCH ECC
...
commit da167ad763 ("rtc: ia64: allow other architectures to use EFI
RTC") inadvertently introduced a regression for x86 because we've been
careful not to enable the EFI rtc driver due to the generally buggy
implementations of the time-related EFI runtime services.
In fact, since the above commit was merged we've seen reports of crashes
on 32-bit tablets,
https://bugzilla.kernel.org/show_bug.cgi?id=84241#c21
Disable it explicitly for x86 so that we don't give users false hope
that this driver will work - it won't, and your machine is likely to
crash.
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org> # v3.17
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
When the rtc-efi driver is built as a module, we already register the
EFI rtc as a platform device if UEFI Runtime Services are enabled.
To wire it up to udev, and let the module be loaded automatically, we
need to export the 'platform:rtc-efi' alias from the module.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Salter <msalter@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Without proper alias kernel module is not loaded for rtc-efi driver.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: dann frazier <dannf@dannf.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nothing major, just handling the RTC driver changes needed for the A31/A23.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kOAE
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/drivers
Pull "Allwinner drivers additions for 3.18" from Maxime Ripard:
Nothing major, just handling the RTC driver changes needed for the A31/A23.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'sunxi-drivers-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
Now that we have Kconfig options for individual sunxi platforms, let
the rtc-sunxi driver depend on the platforms that actually have this
hardware, sun4i and sun7i.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch introduces the driver for the RTC in the Allwinner A31 and
A23 SoCs.
Unlike the RTC found in A10/A20 SoCs, which was part of the timer, the
RTC in A31/A23 are a separate hardware block, which also contain a few
controls for the RTC block hardware (a regulator and RTC block GPIO pin
latches), while also having separate interrupts for the alarms.
The hardware is different enough to make a different driver for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Merge more incoming from Andrew Morton:
"Two new syscalls:
memfd_create in "shm: add memfd_create() syscall"
kexec_file_load in "kexec: implementation of new syscall kexec_file_load"
And:
- Most (all?) of the rest of MM
- Lots of the usual misc bits
- fs/autofs4
- drivers/rtc
- fs/nilfs
- procfs
- fork.c, exec.c
- more in lib/
- rapidio
- Janitorial work in filesystems: fs/ufs, fs/reiserfs, fs/adfs,
fs/cramfs, fs/romfs, fs/qnx6.
- initrd/initramfs work
- "file sealing" and the memfd_create() syscall, in tmpfs
- add pci_zalloc_consistent, use it in lots of places
- MAINTAINERS maintenance
- kexec feature work"
* emailed patches from Andrew Morton <akpm@linux-foundation.org: (193 commits)
MAINTAINERS: update nomadik patterns
MAINTAINERS: update usb/gadget patterns
MAINTAINERS: update DMA BUFFER SHARING patterns
kexec: verify the signature of signed PE bzImage
kexec: support kexec/kdump on EFI systems
kexec: support for kexec on panic using new system call
kexec-bzImage64: support for loading bzImage using 64bit entry
kexec: load and relocate purgatory at kernel load time
purgatory: core purgatory functionality
purgatory/sha256: provide implementation of sha256 in purgaotory context
kexec: implementation of new syscall kexec_file_load
kexec: new syscall kexec_file_load() declaration
kexec: make kexec_segment user buffer pointer a union
resource: provide new functions to walk through resources
kexec: use common function for kimage_normal_alloc() and kimage_crash_alloc()
kexec: move segment verification code in a separate function
kexec: rename unusebale_pages to unusable_pages
kernel: build bin2c based on config option CONFIG_BUILD_BIN2C
bin2c: move bin2c in scripts/basic
shm: wait for pins to be released when sealing
...
The interrupt handler gets the driver data associated with the RTC
device and doesn't check it for validity. This can cause a NULL pointer
being dereferenced when and interrupt fires before the driver data was
properly set up.
Fix this by setting the driver data earlier (before the interrupt is
requested).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In rtc_suspend() and rtc_resume(), the error after rtc_read_time() is not
checked. If rtc device fail to read time, we cannot guarantee the
following process.
Add the verification code for returned rtc_read_time() error.
Signed-off-by: Hyogi Gim <hyogi.gim@lge.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for configuring the ISL12022 real-time clock via the Device
tree framework. This is based on what I've seen in the related ISL12057
driver, it has been tested and works on a Technologic Systems TS-7670
device which uses a ISL12020 RTC device, my device tree looks like this:
apbx@80040000 {
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
clock-frequency = <400000>;
status = "okay";
isl12022@0x6f {
compatible = "isl,isl12022";
reg = <0x6f>;
};
};
... etc
};
Signed-off-by: Stuart Longland <stuartl@vrt.com.au>
Cc: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds alarm support for the NXP PCF8563 chip.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This functions allow to factorize I2C I/O operations.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the rtc-efi driver is restricted to ia64 only. Newer
architectures with EFI support may want to also use that driver. This
patch moves the platform device setup from ia64 into drivers/rtc and
allow any architecture with CONFIG_EFI=y to use the rtc-efi driver.
Signed-off-by: Mark Salter <msalter@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In __rtc_set_alarm(), the error after __rtc_read_time() is not checked.
If rtc device fail to read time, we cannot guarantee the following
process.
Add the verification code for returned __rtc_read_time() error.
Signed-off-by: Hyogi Gim <hyogi.gim@lge.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In particular seeing zero in eft->month is problematic, as it results in
-1 (converted to unsigned int, i.e. yielding 0xffffffff) getting passed
to rtc_year_days(), where the value gets used as an array index
(normally resulting in a crash). This was observed with the driver
enabled on x86 on some Fujitsu system (with possibly not up to date
firmware, but anyway).
Perhaps efi_read_alarm() should not fail if neither enabled nor pending
are set, but the returned time is invalid?
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reported-by: Raymund Will <rw@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5516f09717 ("drivers/rtc/rtc-ds1742.c: remove redundant
of_match_ptr() helper") has description as: "'ds1742_rtc_of_match' is
always compiled in. Hence the helper macro is not needed".
It is not true, of_match_ptr() macro makes of_device_id parameter unused
and this constant is declared with __maybe_unused attribute, so normally
this variable should be discarded by linker. This patch revers this
commit, since there are no reason to compile of_device_id constant for
non-DT systems.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-moxart driver is only useful on MOXA ART systems so it should
depend on ARCH_MOXART as all other MOXA ART drivers already do. Add
COMPILE_TEST as an alternative to allow for build testing on other
systems.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the DS2404 entry together with the other Dallas entries, and add
Maxim so that it looks nicer (and more correct, too.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Sven Schnelle <svens@stackframe.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a patch to add support of nvram for maxim dallas rtc ds1343.
Signed-off-by: Raghavendra Chandra Ganiga <ravi23ganiga@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
This patch changes all absolute SYS_XY registers to offsets from the
SYS block base, prefixes them with AU1000 to avoid silent failures due
to changed addresses, and introduces helper functions to read/write
them.
No functional changes, comparing assembly of a few select functions shows
no differences.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7464/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add register definitions for DA9063 AD (0x3) silicon variant ID
the ability to choose the silicon variant at run-time using regmap
configuration. This patch also adds RTC support for the AD silicon
changes.
It adds both BB and AD support as regmap ranges and then makes the
distinction between the two tables at run-time. This allows both AD
and BB silicon variants to be supported at the same time.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
By using the generic IRQ support in the Register map API, it
is possible to get rid max77686-irq.c and simplify the code.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It is only a typo issue, the related commit:
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (for unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setalarm':
drivers/rtc/rtc-puv3.c:143: error: 'struct device' has no member named 'dev'
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
It is only a typo issue, the related commit:
"1fbc4c4 drivers/rtc/rtc-puv3.c: use dev_dbg() instead of pr_debug()"
The related error (unicore32 with allmodconfig):
CC [M] drivers/rtc/rtc-puv3.o
drivers/rtc/rtc-puv3.c: In function 'puv3_rtc_setpie':
drivers/rtc/rtc-puv3.c:74: error: implicit declaration of function 'dev_debug'
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
Signed-off-by: Xuetao Guan <gxt@mprc.pku.edu.cn>
In probe the configuration of driver for different chipsets was done in
two switch (pdata->device_type) statements. Consolidate them into one
switch statement to increase code readability.
Additionally check the return value of regmap_irq_get_virq and exit
probe on error.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joshua Kinard