If capture and playback are started on different channel (I2S/BT)
there is a possibilty that channel information passed from machine driver
is overwritten before the configuration is done in dma driver.
Example:
113.597588: cz_max_startup: ---playback sets BT channel
113.597694: cz_dmic1_startup: ---capture sets I2S channel
113.597979: acp_dma_hw_params: ---configures capture for I2S channel
113.598114: acp_dma_hw_params: ---configures playback for I2S channel
This is fixed by having 2 separate instance for playback and capture.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW register descriptions says:
"DMA Channel Reset...Software must confirm that this bit is
cleared before reprogramming any of the channel configuration registers."
There could be cases where dma stop errored out leaving dma channel
in reset state. We need to ensure that before the start of another dma,
channel is out of the reset state.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
25Mhz MCLK which was earlier used was of spread type.
Thus, we were not getting accurate rate. The 48Mhz system
clk is of non-spread type and we are changing to it to get
accurate rate.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We support dual channel, 48Khz. This constraint was set only for
da7219. It is being extended to DMIC and MAX98357a.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP->SYSMEM DMA happens at every I2S->SYSMEM period
completion. Thus, there is delay of x frames till
I2S->SYSMEM reaches a period length. This delay is
communicated to user space.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give position on ACP->SYSMEM DMA channel for
the number of bytes that have been transferred on
the basis of current descriptor under service.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In capture case we don't want ACP to SYSMEM dma
to be circular. This is because if an in place DSP
filter is applied to captured output then circular DMA
can overwrite the filter value with stale data.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes
sound/soc/amd/acp-da7219-max98357a.c: In function 'cz_probe':
sound/soc/amd/acp-da7219-max98357a.c:367:3: warning: 'ret' may
be used uninitialized in this function [-Wmaybe-uninitialized]
dev_err(&pdev->dev, "Failed to register regulator: %d\n",
ret);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DA7219 for our platform need to be configured for 1.8V.
Hence, we add a volatge regulator with supplies
of 1.8V in the machine driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having interrupts enabled for ACP<->SYSMEM DMA transfer, we are in
for an interrupt storm.
For both playback and capture interrupts should be enabled for
I2S<->ACP DMA.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Earlier, ch1 was used to define ACP-SYSMEM transfer and ch2 for
ACP-I2S transfer. With recent patches ch1 is used to define channel
order number 1 and ch2 as channel order number 2. Thus,
Playback:
ch1:SYSMEM->ACP
ch2:ACP->I2S
Capture:
ch1:I2S->ACP
ch1:ACP->SYSMEM
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the I2S channel names are fixed, and DMA data flow order is
consistent (ch1 then ch2), we can simplify channel start order:
start the upstream channel and then the downstream channel for both
playback and capture cases.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer() callback gets its value by reading the I2S BYTE_COUNT
register. This is a 64-bit runnning transaction counter. If a
transaction was aborted in the middle of a sample buffer, the counter will
stop counting on a number divisible by the buffer size. Since we actually
use it as a pointer into an aligned buffer, however, we do want to ensure
that it always starts at a number divisible by the buffer size when
starting a transaction, hence we reset it whenever starting a transaction.
To accomplish this, it wasn't necessary to zero bytescount at the
termination of each transaction, so remove this unnecessary code.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On capture, audio data is first copied from I2S to ACP memory, and then
from ACP to SYSRAM. The I2S_TO_ACP_DMA interrupt fires on every sample
transferred from I2S to ACP memory. That is it fires ~48000 times per
second when capturing @ 48 kHz. Since we don't do anything on this
interrupt anyway, disable it to save quite a few unnecessary interrupts.
The real "work" (calling snd_pcm_period_elapsed()) is done when transfer
from ACP to SYSRAM is complete.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On capture, audio data is first copied from I2S to ACP memory, and then
to SYSRAM. For each step the channel number increases, so the names in
the driver were wrong.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is always correct to subtract out the starting bytescount value. Even
in the case of 2^64 byte rollover (292 Million Years in the future
@ 48000 Hz) the math still works out.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6b116dfb46 ("ASoC: AMD: make channel 1 dma as circular") made
both channels circular, so this comment and logic no longer applies. Always
stop ch2 (the channel closest to the output) before ch1. This ensures
that the downstream circular DMA channel does not continue to play/capture
repeated samples after the upstream circular DMA channel has already
stopped.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ST/CZ SoC have 2 channels for capture in the I2SSP path.
The DMA though these channels is done using the same dma
descriptors.
We configure the channel and enable it on the basis of
channel selected by machine driver. Machine driver knows
which codec sits on which channel and thus sends the information
to dma driver.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a correction to match acutal hardware configuration.
The hardware configuration looks like:
I2S_BT -> SPK(Max) + DMIC(Adau)
I2S_SP -> DA7219 Headset
No actual products have been shipped with previous configuration.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix crash in those platforms whose machine driver does not expose
platform_info. For those platforms we rely on default value and
select I2SSP channel.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
channel 1: SYSMEM<->ACP
channel 2: ACP<->I2S
Instead of waiting on period interrupt of ch 2 and then starting
dma on ch1, we make ch1 dma as circular.
This removes dependency of period granularity on hw pointer.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
With in ACP, There are three I2S controllers can be
configured/enabled ( I2S SP, I2S MICSP, I2S BT).
Default enabled I2S controller instance is I2S SP.
This patch provides required changes to support I2S BT
controller Instance.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
System clock on the platform is 25Mhz and not 24Mhz.
PLL_OUT for da7219 codec to use DA7219_PLL_FREQ_OUT_98304
as it is for 48KHz SR.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
hw_param can be called multiple times and thus we can have
more clk enable. The clk may not get diabled due to refcounting.
startup/shutdown ensures single clk enable/disable call.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd structure freed early may result in kernel panic in dma close
call back. moved releasing memory for rtd structure to the end of
dma close callback.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added sram bank variable to audio_substream_data structure.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added pte offset variable in audio_substream_data structure.
Added Stoney related PTE offset macros in acp header file.
Modified hw_params callback to assign the pte offset value
based on asic_type.
PTE Offset macros used to calculate no of PTE entries
need to be programmed when memory allocated for audio buffer.
Depending upon allocated audio buffer size, PTE offset values
will change.
Compared to CZ, Stoney has SRAM memory limitation i.e 48k
It is required to define separate PTE Offset macros for
Stoney.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removed separate byte count variables for playback and capture.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added dma configuration parameters to rtd structure.
Moved dma configuration parameters initialization to
hw_params callback.
Removed hard coding in prepare and trigger callbacks.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to make audio_substream_data structure variable
consistent throughout the code, changed the name from
audio_config to rtd wherever applicable.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warning:
sound/soc/amd/acp-da7219-max98357a.c:46:12: warning:
symbol 'da7219_dai_clk' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit c88d311533 ("ASoC: amd: Enable da7219 master clock using common
clock framework") is using rtd->codec, but codec is replaced to component.
Let's use component
Fixes: c88d311533 ("ASoC: amd: Enable da7219 master clock using common clock framework")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DA7219 is clock master for other codecs. DA7219 has exposed clock
control by using common clock framework and same is used to enable
and disable clock for all codecs in the system.
TEST=aplay -D hw:0,0 -vv <file>
arecord -D hw:0,0 -f dat -d 5 -vv <file>
aplay -D hw:0,1 -vv <file>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BT I2S is a bi-directional dai, we will use the same
cpu dai for playback and capture.
TEST=aplay -D hw:0,0 -vv <file>
arecord -D hw:0,0 -f dat -d 5 -vv <file>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per design, non-circular dma also need to be
stopped explicitly for both playback and capture
scenarios.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Moved 16bit resolution condition check for stoney platform
to acp_hw_params.Depending upon substream required register
value need to be programmed rather than enabling 16bit resolution
support all time in acp init.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removed hardcoding in dma descriptor programming api's.
These changes are required to extend the logic to support
dma descriptor programming for multiple i2s controller
instances.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With in ACP, There are three I2S controllers can be configured.
(I2S SP ,I2S MICSP and I2S BT).These controllers can
support both playback/capture scenarios.
Default enabled i2s controller instance is i2s sp instance.
Renamed stream names and bytescount params as i2ssp.
These changes required to distinguish with other I2S controller
instance pcm substreams and bytescount params.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now we can replace Codec to Component. Let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown