This allows the user to specify DMA aggregation timout and block
count. Blocks are presumably always 512 bytes, so the minimum block
count is 6 for 802.11 packets.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gen2 chips as well as 8188eu seems to use this register for setting
DMA timeout threshold values, however the 8192cu is using
REG_USB_DMA_AGG_TO. Set both to be on the safe side.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Let the default to off until we have more data on the right default
tuning values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables aggregation on rtl8192cu and derivative parts. This uses
the same parameters as for rtl8723au.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement rtl8xxxu_gen1_init_aggregation(). Aggregation should be the
same for all gen1 parts. We may want to allow for tuning parameters in
the fileopes struct. For now this is based allocating 16KB RX buffers,
leaving 16000 bytes for actual packets, and the rest for the skb
overhead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old allocation didn't leave space for phystats in the buffer,
allowing the packet to be rejected if a frame size of size
IEEE80211_MAX_FRAME_LEN was received.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds support for allocating larger skbs for devices which
indicate they support it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements support for demuxing aggregated RX packets on gen1
devices, using the rxdesc16 format.
So far this has only been tested with rtl8723au devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This corrects the definition of rxdesc16 to correctly specify pkt_cnt
for aggregated packets. This is based on the code of the vendor
rtl8723au driver, as opposed to the struct definitions they use.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When handling aggregated packets, we'll get a new ieee80211_rx_status
for each cloned skb, so passing in the pointer from the outside
doesn't make sense.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is another prepatory patch to be able to handle aggregated RX
packets.
In order to avoid adding a prototype, this also moves the
rtl8723bu_handle_c2h() function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This needs to be handled locally in the parse_rx_desc() function in
order to be able to handle aggregated packets in the future.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB urbs will return with a status != 0 when rmmod'ing the driver. No
need to fill the log with messages from rtl8xxxu_int_complete()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
reg_eac and reg_ecc are only used if candidate is bigger than 0, and in
that case new values will be given to them. Removing the unused
assignments.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph specifier to dump small buffers in hex format instead of doing this
byte-by-byte.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
path_b_ok is being assigned but immediately after path_a_ok is being
compared to the value 0x03. This appears to be a typo on the
variable name, compare path_b_ok instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With two different h2c_cmd() functions, mbox_ext_reg and
mbox_ext_width are no longer needed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename it to rtl8xxxu_gen2_prepare_calibrate() and remove the calls to
it from rtl8xxxu_gen1_phy_iq_calibrate()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The H2C API is completely different between gen1 and gen2 parts, so
there is little point trying to treat this as a generic function. All
calls to *_h2c_cmd() will always come from a gen1 or a gen2 specific
function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic to most of the chips, so change the name to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is generic for most (if not all) gen1 parts, so rename
it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is nothing 8723au specific about this function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the code for rtl8188c, rtl8188r, and rtl8192c into it's own
file. This is purely a code moving exercise, there is no change to the
code itself.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the rtl8723a code into it's own file. This is purely a code
moving exercise, no code changes.
This device specific file is a lot smaller since the gen1 chips
(8723a, 8188c, 8188r, 8192c) share a lot more common code than the
gen2 chips.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the rtl8723b code into it's own file. This is purely a code
moving exercise, no functional changes. This did expose
rtl723a_h2c_cmd() as a function that should be refactored into a gen1
and a gen2 version.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the rtl8192e code into it's own file. This is purely a code
moving exercise, no code changes.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This renames the core file to rtl8xxxu_core.c in order to allow us to
keep the module nake rtl8xxxu.ko when refactoring the code into
multiple files.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is nothing 8723au specific about rtl8723au_iqk_phy_iq_bb_reg so
rename the array to rtl8xxxu_iqk_phy_iq_bb_reg.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This renames rtl8723bu_simularity_compare() to
rtl8xxxu_gen2_simularity_compare() to reflect it is used for all gen2
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This renames rtl8723b_channel_to_group() to
rtl8xxxu_gen2_channel_to_group() to reflect it is used by all
currently supported gen2 parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same mac_init_table, so
rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All gen1 parts use the same enable_rf() function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All gen1 parts use the same interface for setting TX power, so rename
the function to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All gen1 parts use the same init_phy_bb() function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All supported gen1 parts use the same phy_iq_calibrate() function
(unlike their gen2 counterparts). Rename the function to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same function for updating
the rate mask, so rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All supported gen1 parts use the same config_channel() function, so
rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same disable_rf() routine,
so rename the function to reflect that.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At least for now, all gen2 parts use the same disable_rf() function
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function to indicate it is applicable to most/all gen2
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function to reflect it is for all/most gen1 parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the name reflect this is for most/all gen2 parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update the name of rtl8723bu_update_rate_mask() to make it reflect
it's applicable for all/most gen2 N parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The references to some arrays in the rtl8xxxu driver were moved inside
of an #ifdef, but the symbols remain outside, resulting in build warnings:
rtl8xxxu/rtl8xxxu.c:1506:33: error: 'rtl8188ru_radioa_1t_highpa_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1431:33: error: 'rtl8192cu_radioa_1t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1407:33: error: 'rtl8192cu_radiob_2t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1332:33: error: 'rtl8192cu_radioa_2t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:239:35: error: 'rtl8192c_power_base' defined but not used
rtl8xxxu/rtl8xxxu.c:217:35: error: 'rtl8188r_power_base' defined but not used
This adds an extra #ifdef around them to shut up the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2fc0b8e5a1 ("rtl8xxxu: Add TX power base values for gen1 parts")
Fixes: 4062b8ffec ("rtl8xxxu: Move PHY RF init into device specific functions")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the disable_rf() functions were setting REG_TXPAUSE to 0xff to
stop transmission. Do it centrally before calling disable_rf()
instead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements an 8192eu specific enable_rf() function. The 8192eu is
not a combo device, so no need for doing the BT specific bits needed
by the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver relies on driver_info in struct usb_device_id, so allowing
adding a device via /sys/bus/usb/drivers/rtl8xxxu/new_id will cause a
NULL pointer dereference.
Set .no_dynamic_id = 1 to disable hot add of USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8188RU does not like PAPE to be enabled, while all the other gen1
parts seem to require it.
This makes the RTL8188RU able to associate for me.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This register is undocumented in the vendor code, but it is set
unconditionally for all 8192cu/8188cu/8188ru parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a long standing bug where mac80211 would send disconnect
packets to the device, after we had shut down the device.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In particular set APS_FSMCO_WLON_RESET in the right register, and do
not overwrite too much of REG_CR.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is simpler than checking for RTL8188C && hi_pa.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch was being missed since rtl_chip will never match RTL8188C
if hi_pa is true.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per the vendor driver, devices with an external PA needs limiting it's
TX power to 0x20.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Load the RF table in init_phy_rf(), which allows for applying device
specific RF hacks in the same place. Getting rid of more ugly if ()
clutter.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
several functions are not initializing a return status in ret
resulting in garbage to be returned instead of 0 for success.
Currently, the calls to these functions are not checking the
return, however, it seems prudent to return the correct status
in case they are to be checked at a later date.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This dongle was tested successfully by Andrea Merello
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Write the adjusted value back to the correct register
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This removes an unneeded hack for 8192eu, and allows for initializing
REG_FPGA0_XAB_RF_SW_CTRL at the same point as it is done for all other
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This removes a bunch of if () spaghetti and re-applies the USB bus
quirks for 8188/8192 that had gotten lost.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rather than scattering the code with #ifdefs, use the fileops
structure to hold device specific PBP values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was expired by the vendor driver, but we never ended up using the
backed up value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the loading of the AGC table into init_phy_bb() and reduces
the if() clutter.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This should get the order right and avoid patching something that is
later overwritten.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reduces the if () clutter. Longer term it probably makes sense to
split this between gen1 (8723au/8188cu/8192cu) and gen2
(8192eu/8723bu) devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old code incorrectly wiped out bits 0-23 by mistake when setting
the RX path for 1T parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu is a combo WiFi/BT dongle, and path B is not used for WiFi,
so no point in calibrating it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No actual code flow change, but no need to warn about something that
isn't a prioblem.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This caught a bug where too little memory was allocated for RX urbs
for parts using 24 byte RX descriptors
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This shouldn't affect little endian system, but may have prevented the
driver working on big endian systems for devices with the larger 24
byte RX descriptors.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead use tx_desc_size() to distinguish between gen1
(8723a/8192c/8188c) and gen2 (8723b/8192e) parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8192eu is a 2T part, so setting TX power for path A only, as done by
rtl8723bu_set_tx_power() is not sufficient.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Presumably 8192eu devices do not have leds, so do not enable them.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like the 8723bu, the vendor driver does not set FPGA0_TX_INFO for
8192eu in the init sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vendor driver does not set REG_PBP on 8192eu. Whether this is due
to the device not supporting it or simply an oversight in the vendor
driver is not clear.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Another flow order change to match the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Longer term we should switch all the chips over to use this function
instead of the random chip specific ifdef hacks.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This further reorganizes the init code flow to match that of the
8192eu vendor driver. This helps diffing the register write log
against that of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to debug 8192eu support, reorder some init code to match the
flow of the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adjust AFE before enabling PLL on 8192eu, probably also needed for
8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixup another case where the hard coded register value was used
instead of the name.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement workaround for LDPC RX hands on 8192eu. This was inspired by
workaround found in the 8192eu vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set HIMR[01] on 8192eu instead of HISR/HIMR. It's not obvious this
really matters for USB devices, but this matches the register writes
performed by the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set REG_AFE_XTAL_CTRL on 8192eu to the vendor driver value, and do not
skip setting REG_MAX_AGGR_NUM on 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu requires clearing/restoring bit 17 in REG_FPGA0_POWER_SAVE
before/after writing RF registers.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu does not use REG_AFE_PLL_CTRL in it's BB init sequence, so
provide device specific handling.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu efuse only has power data for path A and B. It follows the
same layout as 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pick PHY init table based on device before distinguishing between
1T/2T/high PA tables. The latter is only currently used for
8188cu/8192cu/8188ru.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu also requires it's own PHY init table.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jes Sorensen