This patch implements LED feature of directly attached disk for v2 hw.
As libsas has provided an interface lldd_write_gpio() for this feature,
we just need realise the interface following SPGIO API.
We use an CPLD to finish the hardware part of this feature, and the base
address of CPLD should be configured through ACPI or DT tables.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to ATA protocol, SET MAX commands belong to different frame
types. So judge features field of SET MAX commands to decide which
frame type they belongs to.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For v3 hw SAS, it supports configuring power state from D0 to D3 for entering
Low Power status and power state from D3 to D0 for quit Low Power status.
When power state from D0 to D3, HW will send FLR to clear the registers of
ECAM and BAR space, and when power state from D3 to D0, it will clear the
registers of ECAM space only.
So when suspend, need to do like controller reset (including disable
interrupts/DQ/PHY/BUS), and also release slots after FLR. When resume,
re-config the registers of BAR space.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We should do link reset of PHY when identify timeout or STP link timeout. They
are internal events of SOC and are notified to driver through interrupts of
CHL_INT2.
Besides, we should add an delay work to do link reset as it needs sleep. So,
this patch add an new PHY event HISI_PHYE_LINK_RESET for this.
Notes: v2 HW doesn't report the event of STP link timeout. So, we only need
to handle event of identify timeout for v2 HW.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use an general way to do delay work for a PHY. Then it will be easier to add
new delayed work for a PHY in future.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes it is required to know when the controller reset has completed and
also if it has completed successfully. For such places, we call
hisi_sas_controller_reset() directly before. That may lead to multiple calls
to this function.
This patch create a per-reset structure which contains a completion structure
and status flag to know when the reset completes and also the status. It is
also in hisi_hba.wq to do reset work.
As all host reset works are done in hisi_hba.wq, we don't worry multiple calls
to hisi_sas_controller_reset().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In certain scenarios we may just want to clear the ITCT for a device, and not
free other resources like the SATA bitmap using in v2 hw.
To facilitate this, this patch relocates the code of clearing ITCT from
free_device() to a new hw interface clear_itct(). Then for some hw, we should
not realise free_device() if there's nothing left to do for it.
[mkp: typo]
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This requires adding a pointer to
hold the timer's target task, as there isn't a link back from slow_task.
Cc: John Garry <john.garry@huawei.com>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Jack Wang <jinpu.wang@profitbricks.com>
Cc: lindar_liu@usish.com
Cc: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Benjamin Block <bblock@linux.vnet.ibm.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: John Garry <john.garry@huawei.com> # for hisi_sas part
Tested-by: John Garry <john.garry@huawei.com> # basic sanity test for hisi_sas
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
The CQ event is handled in tasklet context, and it could be delayed if
the system loading is high.
It is possible to run into some problems when executing a host reset
when cq_tasklet_vx_hw() is being executed.
So, prior to host reset, execute tasklet_kill() to ensure that all CQ
tasklets are complete.
Besides, as the function hisi_sas_wait_tasklets_done() is added to do
tasklet_kill(), this patch refactors some code where tasklet_kill() is
used.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add init code of hisi_hba->rst_work for v3 hw. Because v3 hw also need
it to recover controller when some hw errors occurs.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print AXI errors in v2 hw driver is repetitive.
This patch condenses the code by looping an array of errors.
Also, a formatting error in one_bit_ecc_errors[] and
multi_bit_ecc_errors[] is fixed.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a PHY_FUNC_LINK_RESET is issued, we need to fill the transport
identify_frame to SAS controller before the PHYs are enabled.
Without this, we may find that if a PHY which belonged to a wideport
before the reset may generate a new port id.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the size of memory we allocate for SATA breakpoint buffer is
incorrect.
The breakpoint memory size should be as follows: 32 (NCQ tags) * 128 *
2048 (max #devs) = 8MB
Currently we only allocate 0.5MB, but get away with it as we never
have SATA device index > 128 typically.
To conserve precious DMA memory (8MB may not be even available), limit
the number of devices per HBA to 1024, which means 4MB of memory
required for SATA breakpoint.
The 1024 device limit applied to all HW versions. For v3 hw, we need
to configure this value.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver version is not updated with changes to the driver, so it has
no value, so just get rid of it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a fix related to freeing a device in v2 hw driver.
Before, we polled to ITCT CLR interrupt to check if a device is free.
This was error prone, as if the interrupt doesn't occur in 10us, we miss
processing it.
To avoid this situation, service this interrupt and sync the event with
a completion.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The code to print ECC errors in v2 hw driver is very repetitive. This
patch condensed the code by looping an array of errors.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add DFX feature for v2 hw. We are adding support for
the following errors:
- loss_of_dword_sync_count
- invalid_dword_count
- phy_reset_problem_count
- running_disparity_error_count
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides fixes for the following issues:
1. Fix issue of controller reset required to send commands. For reset
process, it may be required to send commands to the controller, but
not during soft reset. So add HISI_SAS_NOT_ACCEPT_CMD_BIT to prevent
executing a task during this period.
2. Send a broadcast event in rescan topology to detect any topology
changes during reset.
3. Previously it was not ensured that libsas has processed the PHY up
and down events after reset. Potentially this could cause an issue
that we still process the PHY event after reset. So resolve this by
flushing shot workqueue in LLDD reset.
4. Port ID requires refresh after reset. The port ID generated after
reset is not guaranteed to be the same as before reset, so it needs
to be refreshed for each device's ITCT.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we allocate 3 sets of DMA memories from separate pools for
each slot. This is inefficient in terms of memory usage
(buffers are less than 1 page in size, so we lose due to alignment),
and also time spent in doing 3 allocations + de-allocations per slot,
instead of 1.
To optimise, combine the 3 DMA buffers into a single buffer from a
single pool.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Element phy_type is a bitmask and it only ever has 2 bits possibly set,
and it is overkill to define as a u64, so redefine as a u32.
This change resolves static code check complaint that "phy->phy_type &=
~PORT_TYPE_SAS;" would unintentionally clear the high 32 bits as well.
Structure hisi_sas_phy is also reordered to ensure packing efficiency.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a change for abort dev for v3 hw: add registers to configure
unaborted iptt for a device, and then inform this to logic.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the code to initialise the controller which is based on pci device
in hisi_sas_v3_hw.c
The core controller routines are still in hisi_sas_main.c; some common
initialisation functions are also exported from hisi_sas_main.c
For pci-based controller, the device properties, like phy count and sas
address are read from the firmware, same as platform device-based
controller.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move the functionality to retrieve the fw info into a dedicated device
type-agnostic function, hisi_sas_get_fw_info().
The reasoning is that this function will be required for future
pci-based platforms.
Also add some debug logs for failure.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since hip08 SAS controller is based on pci device, add hisi_hba.pci_dev
for hip08 (will be v3), and also rename hisi_hba.pdev to .platform_dev
for clarity.
In addition, for common code which wants to reference the controller
device struct, add hisi_hba.dev, and change the common code to use it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate get_ncq_tag_v2_hw() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate get_ata_protocol() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate get_ata_protocol() to a common location, as future hw versions
will require it. Also rename with "hisi_sas_" prefix for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently hisi_hba.lock is locked to deliver and receive a command
to/from any hw queue. This causes much contention at high data-rates.
To boost performance, lock on a per queue basis for sending and
receiving commands to/from hw.
Certain critical regions still need to be locked in the delivery and
completion stages with hisi_hba.lock.
New element hisi_sas_device.dq is added to store the delivery queue for
a device, so it does not need to be needlessly re-calculated for every
task.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently hisi_sas_device.device_id is a u64. This can create a problem
in selecting the queue for a device, in that this code does a 64b
division on device id. For some 32b systems, 64b division is slow and
the lib reference must be explicitly included.
The device id does not need to be 64b in size, so, as a solution, just
make as an int.
Also, struct hisi_sas_device elements are re-ordered to improve packing
efficiency.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is a workaround for a SoC bug where an internal abort command
may timeout. In v2 hw, the channel should become idle in order to finish
abort process. If the target side has been sending HOLD, host side
channel failed to complete the frame to send, and can not enter the idle
state. Then internal abort command will timeout.
As this issue is only in v2 hw, we deal with it in the hw layer. Our
workaround solution is: If abort is not finished within a certain period
of time, we will check HOLD status. If HOLD has been sending, we will
send break command.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch provides a workaround a SoC bug where SATA IPTTs for
different devices may conflict.
The workaround solution requests the following:
1. SATA device id must be even and not equal to SAS IPTT.
2. SATA device can not share the same IPTT with other SAS or
SATA device.
Besides we shall consider IPTT value 0 is reserved for another SoC bug
(STP device open link at firstly after SAS controller reset).
To sum up, the solution is: Each SATA device uses independent and
continuous 32 even IPTT from 64 to 4094, then v2 hw can only support 63
SATA devices. All SAS device(SSP/SMP devices) share odd IPTT value from
1 to 4095.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After resetting the controller, the process of scanning SATA disks
attached to an expander may fail occasionally. The issue is that the
controller can't close the STP link created by target if the max link
time is 0.
To workaround this issue, we reject STP link after resetting the
controller, and change the corresponding PHY to accept STP link only
after receiving data.
We do this check in cq interrupt handler. In order not to reduce
efficiency, we use an variable to control whether we should check and
change PHY to accept STP link.
The function phys_reject_stp_links_v2_hw() should be called after
resetting the controller.
The solution of another SoC bug "SATA IO timeout", that also uses the
same register to control STP link, is not effective before the PHY
accepts STP link.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently when a root PHY is deformed from a asd_sas_port we try to
release the slots in the LLDD, and fail.
Regardless, it is not right to release this early.
This patch removes the deformed function. As it was before, port
deformation is still done in hisi_sas_phy_down().
It would be nice to actually remove the hisi_sas_port_{de}formed() pair,
however we cannot as we need to know the asd_sas_port index libsas has
associated with an asd_sas_phy.
The hw does actually generate a port id for a PHY, but this seems to a
random number, so ignored for this purpose.
This patch also changes the code to link slots to the hisi_sas_device,
and not hisi_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Relocate the PHY init code from LLDD hw init path to
hisi_sas_scan_start().
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are some scenarios that we need to warm-reset to reset registers
of SAS controller. During reset we disable interrupts/DQs/PHYs, and
after reset we re-init the hardware and rescan the topology to see if
anything changed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce function to get hisi_sas_port from asd_sas_port.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the all the slot processing for the completion queue is done
in ISR context. It is judged that the slot processing can take a long
time, especially when a SATA NCQ completes (upto 32 slots).
So, as a solution, defer the bulk of the ISR processing to tasklet
context. Each CQ will have its down tasklet.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the function to set PHY min and max linkrate through
sysfs interface.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes the value of hisi_sas_device.running_req
would go negative unless we have the check for
running_req >= 0 before trying to decrement.
This is because using running_req is not thread-safe.
As such, the value for running_req may be actually incorrect,
so use atomic64_t instead.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently slots are allocated from queues in a round-robin fashion.
This causes a problem for internal commands in device mode. For this
mode, we should ensure that the internal abort command is the last
command seen in the host for that device. We can only ensure this when
we place the internal abort command after the preceding commands for
device that in the same queue, as there is no order in which the host
will select a queue to execute the next command.
This queue restriction makes supporting scsi mq more tricky in
the future, but should not be a blocker.
Note: Even though v1 hw does not support internal abort, the
allocation method is chosen to be the same for consistency.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hip06 D03 and hip07 D05 boards have different reference clock
frequencies for the SAS controller.
Register PHY_CTRL needs to be programmed differently according to this
frequency, so add support for this.
The default register setting in PHY_CTRL is for 50MHz, so only update
this register when the refclk frequency is 66MHz.
For ACPI we expect the _RST handler to set the correct value for
PHY_CTRL (we're forced to take different approach for DT and ACPI as
ACPI does not support fixed-clock device).
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimise by saving an avoidable read in the get_free_slot function. The
delivery queue write pointer will only be updated by software, so don't
bother re-reading what was already written in the previous call to
start_delivery function.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimise by saving an avoidable read in the cq interrupt. The queue
read pointer will only be updated by software, so don't bother
re-reading what was already written in the previous interrupt.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add main code for internal abort functionality.
The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.
Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.
Two modes of internal abort are supported:
- device
- individual command
For device, when the internal abort is issued all commands in the host
for that device are aborted. For a single command, only that command is
aborted if it is still in the host.
In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add methods to use HW specific versions of functions to allocate slot
and device. HW specific methods are permitted to workaround device id
vs IPTT collision issue in v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan