The configuration space mapping on Tegra is somewhat special, and in order
to avoid wasting virtual address space the configuration space for each bus
needs to be stitched together from several blocks which form a single
continuous virtual address range for accessors.
Currently the configuration space is mapped upon the first access to one of
its registers. However, the mapping operation may sleep under certain
circumstances, so doing it from the configuration space accessors (they are
protected by a spin lock) will trigger a warning.
To avoid the warning, use the ->add_bus() callback to perform the mapping
at enumeration time when the operation is allowed to sleep. Also add an
implementation of ->remove_bus() that undoes the mapping established by the
->add_bus() callback. While it isn't currently possible to unload the
module, there is work underway to remedy this, and this code will come in
handy when that happens.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Modify the Microblaze PCI subsystem to work with the generic
drivers/pci/host/pcie-xilinx.c driver on Microblaze and Zynq.
[bhelgaas: changelog]
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The Xilinx AXI PCIe Host Bridge Soft IP driver was previously only
supported on ARM (in particular, on ARCH_ZYNC), and pci_fixup_irqs() is
available there. But Microblaze will do IRQ fixup in pcibios_add_device(),
so pci_fixup_irqs() is not available on Microblaze.
Don't call pci_fixup_irqs() on Microblaze, so the driver can work on both
Zynq and Microblaze Architectures.
[bhelgaas: revise changelog to show similarity to bdb8a1844f ("PCI: iproc: Call pci_fixup_irqs() for ARM64 as well as ARM")]
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The Xilinx PCIe host controller driver uses pci_common_init_dev(), which
is ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
[bhelgaas: revise changelog to show similarity to 79953dd22c ("PCI: rcar: Remove dependency on ARM-specific struct hw_pci")]
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Use the new of_pci_get_host_bridge_resources() API in place of the PCI OF
DT parser.
[bhelgaas: revise changelog to show similarity to 0021d22b73 ("PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT")]
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The settings in GPR8 are dependent upon the particular layout of the
hardware platform. As such, they should be configurable via the device
tree.
Look up PHY Tx driver settings from the device tree. Fall back to the
original hard-coded values if they are not specified in the device tree.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Some kinds of Layerscape PCIe controllers will forward the received message
TLPs to system application address space, which could corrupt system memory
or lead to a system hang. Enable MSG_DROP to fix this issue.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit cbce790059 ("PCI: designware: Make driver arch-agnostic") changed
the host bridge sysdata pointer from the ARM pci_sys_data to the DesignWare
pcie_port structure, and changed pcie-designware.c to reflect that. But it
did not change the corresponding code in pci-keystone-dw.c, so it caused
crashes on Keystone:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
pgd = c0003000
[00000030] *pgd=80000800004003, *pmd=00000000
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.4.2-00139-gb74f926 #2
Hardware name: Keystone
PC is at ks_dw_pcie_msi_irq_unmask+0x24/0x58
Change pci-keystone-dw.c to expect sysdata to be the struct pcie_port
pointer.
[bhelgaas: changelog]
Fixes: cbce790059 ("PCI: designware: Make driver arch-agnostic")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.4+
CC: Zhou Wang <wangzhou1@hisilicon.com>
This driver uses PCI glue that is only available on 32-bit ARM. This used
to work fine as long as ARCH_MVEBU and ARCH_DOVE were exclusively 32-bit,
but there's a patch in the pipe to make ARCH_MVEBU also available on 64-bit
ARM.
[bhelgaas: changelog; patch is coming but not merged yet]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a new driver which exposes a root PCI bus whenever a PCI Express device
is passed through to a guest VM under Hyper-V. The device can be single-
or multi-function. The interrupts for the devices are managed by an IRQ
domain, implemented within the driver.
[bhelgaas: fold in race condition fix (http://lkml.kernel.org/r/1456340196-13717-1-git-send-email-jakeo@microsoft.com)]
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe designware host driver is not used in system configurations
requiring the PCI_PROBE_ONLY flag to be set to prevent resources
assignment, therefore the driver code handling the flag can be removed
from the kernel.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Acked-by: Jingoo Han Jingoo Han <jingoohan1@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Some platforms don't support ATU, e.g., pci-keystone.c. These platforms
use their own address translation component rather than ATU, and they
provide the rd_other_conf and wr_other_conf methods to program the
translation component and perform the access.
Add a comment to explain why we don't program the ATU for these platforms.
[bhelgaas: changelog]
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Layerscape PCI host driver must recognize ls2085a compatible when using
firmware with ls2085a compatible property, otherwise the PCI bus won't be
detected even though ls2085a compatible is included by the dts.
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe rcar host driver is not used in system configurations requiring
the PCI_PROBE_ONLY flag to be set to prevent resources assignment,
therefore the driver code handling the flag can be removed from the kernel.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Commit 943ebae781 ("PCI: iproc: Add PAXC interface support") only allowed
device 0, which is a regression on BCMA-based platforms.
All systems support only one device, a Root Port at 00:00.0, on the root
bus. PAXC-based systems support only the Root Port (00:00.0) and a single
device (with multiple functions) below it, e.g., 01:00.0, 01:00.1, etc.
Non-PAXC systems support arbitrary devices below the Root Port.
[bhelgaas: changelog, fold in removal of MAX_NUM_PAXC_PF check]
Fixes: 943ebae781 ("PCI: iproc: Add PAXC interface support")
Reported-by: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
imx6_pcie_link_up() previously used usleep_range() to wait for the link to
come up. Since it may be called while holding the config spinlock, the
sleep causes a "BUG: scheduling while atomic" error.
Instead of waiting for the link to come up in imx6_pcie_link_up(), do the
waiting in imx6_pcie_wait_for_link(), where we're not holding a lock and
sleeping is allowed.
[bhelgaas: changelog, references to bugzilla and f95d3ae771]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100031
Fixes: f95d3ae771 ("PCI: imx6: Wait for retraining")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the remnants of the workaround for erratum ERR005184 which was never
completely implemented. The checks alone don't carry any value as we don't
act properly on the result.
A workaround should be added to the lane speed change in establish_link
later.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds the PHY reset into a common error path of
imx6_pcie_establish_link(), deduplicating some of the debug prints. Also
reduce the severity of the "no-link" message in the one place where it is
expected to be hit when no peripheral is attached.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move imx6_pcie_reset_phy() near the other PHY related functions in the
file. This is a cosmetic change, but also allows to do the following
changes without introducing needless forward declarations.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/trivial:
PCI: shpchp: Constify hpc_ops structure
PCI: Use kobj_to_dev() instead of open-coding it
PCI: Use to_pci_dev() instead of open-coding it
PCI: Fix all whitespace issues
PCI/MSI: Fix typos in <linux/msi.h>
For PCIe compliance, the PHY registers need setting as per the manual.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
If runtime PM is enabled in the kernel config, simply enable the clocks
once during probe.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Drivers based on the DesignWare core can override the config read accessors
by supplying rd_own_conf() and rd_other_conf() function pointers.
dw_pcie_rd_conf() calls dw_pcie_rd_own_conf() (for accesses to the root
bus) or dw_pcie_rd_other_conf():
dw_pcie_rd_conf
dw_pcie_rd_own_conf # if on root bus
dw_pcie_rd_other_conf # if not on root bus
Previously we checked for rd_other_conf() directly in dw_pcie_rd_conf(),
but we checked for rd_own_conf() in dw_pcie_rd_own_conf().
Check for rd_other_conf() in dw_pcie_rd_other_conf() to make this symmetric
with the rd_own_conf() checking, and similarly for the write path.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The pci_sys_data struct was previously used by pci_common_init_dev() and by
the ARM pcibios_align_resource(), but recent commits removed those uses:
cbce790059 ("PCI: designware: Make driver arch-agnostic")
b3a72384fe ("ARM/PCI: Replace pci_sys_data->align_resource with global function pointer")
cbce790059 removed the use of pci_common_init_dev() by DesignWare
drivers, including pcie-rcar.c, and b3a72384fe removed the use of struct
pci_sys_data by the ARM pcibios_align_resource().
Remove struct pci_sys_data from pcie-rcar.c.
[bhelgaas: changelog]
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the HiSilicon Hip06 SoC. Documentation has been updated to
include Hip06. Add Gabriele Paoloni as maintainer of the driver.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Fix all whitespace issues (missing or needed whitespace) in all files in
drivers/pci. Code is compiled with allyesconfig before and after code
changes and objects are recorded and checked with objdiff and they are not
changed after this commit.
Signed-off-by: Bogicevic Sasa <brutallesale@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Mark the dra7xx PCI host driver as broken. This driver was first merged in
v3.17 and has never worked. Although the driver compiles just fine, it is
missing an essential device reset. If the driver is included, the kernel
locks up hard shortly after booting, before any console output appears.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add PCIe MSI support for both PAXB and PAXC interfaces on all iProc-based
platforms.
The iProc PCIe MSI support deploys an event queue-based implementation.
Each event queue is serviced by a GIC interrupt and can support up to 64
MSI vectors. Host memory is allocated for the event queues, and each event
queue consists of 64 word-sized entries. MSI data is written to the lower
16-bit of each entry, whereas the upper 16-bit of the entry is reserved for
the controller for internal processing.
Each event queue is tracked by a head pointer and tail pointer. Head
pointer indicates the next entry in the event queue to be processed by
the driver and is updated by the driver after processing is done.
The controller uses the tail pointer as the next MSI data insertion
point. The controller ensures MSI data is flushed to host memory before
updating the tail pointer and then triggering the interrupt.
MSI IRQ affinity is supported by evenly distributing the interrupts to each
CPU core. MSI vector is moved from one GIC interrupt to another in order
to steer to the target CPU.
Therefore, the actual number of supported MSI vectors is:
M * 64 / N
where M denotes the number of GIC interrupts (event queues), and N denotes
the number of CPU cores.
This iProc event queue-based MSI support should not be used with newer
platforms with integrated MSI support in the GIC (e.g., giv2m or
gicv3-its).
[bhelgaas: fold in Kconfig fixes from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
On -RT and if kernel is booting with "threadirqs" cmd line parameter,
PCIe/PCI (MSI) IRQ cascade handlers (like dra7xx_pcie_msi_irq_handler())
will be forced threaded and, as result, will generate warnings like this:
WARNING: CPU: 1 PID: 82 at kernel/irq/handle.c:150 handle_irq_event_percpu+0x14c/0x174()
irq 460 handler irq_default_primary_handler+0x0/0x14 enabled interrupts
Backtrace:
(warn_slowpath_common) from (warn_slowpath_fmt+0x38/0x40)
(warn_slowpath_fmt) from (handle_irq_event_percpu+0x14c/0x174)
(handle_irq_event_percpu) from (handle_irq_event+0x84/0xb8)
(handle_irq_event) from (handle_simple_irq+0x90/0x118)
(handle_simple_irq) from (generic_handle_irq+0x30/0x44)
(generic_handle_irq) from (dra7xx_pcie_msi_irq_handler+0x7c/0x8c)
(dra7xx_pcie_msi_irq_handler) from (irq_forced_thread_fn+0x28/0x5c)
(irq_forced_thread_fn) from (irq_thread+0x128/0x204)
This happens because all of them invoke generic_handle_irq() from the
requested handler. generic_handle_irq() grabs raw_locks and thus needs to
run in raw-IRQ context.
This issue was originally reproduced on TI dra7-evem, but, as was
identified during discussion [1], other hosts can also suffer from this
issue. Fix all them at once by marking PCIe/PCI (MSI) IRQ cascade handlers
IRQF_NO_THREAD explicitly.
[1] http://lkml.kernel.org/r/1448027966-21610-1-git-send-email-grygorii.strashko@ti.com
[bhelgaas: add stable tag, fix typos]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de> (for imx6)
CC: stable@vger.kernel.org
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Kukjin Kim <kgene@kernel.org>
CC: Krzysztof Kozlowski <k.kozlowski@samsung.com>
CC: Richard Zhu <Richard.Zhu@freescale.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
CC: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Return values immediately when possible to simplify the control flow.
No functional change intended. Folded in unused variable removal as
pointed out by Fabio Estevam <fabio.estevam@nxp.com>, Arnd Bergmann
<arnd@arndb.de>, and Thierry Reding <thierry.reding@gmail.com>.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The PCIe driver reuses the Designware common code for host and MSI
initialization, and also programs the Qualcomm application specific
registers.
[bhelgaas: remove COMPILE_TEST Kconfig dependency]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Read back the ATU CR2 register to ensure ATU programming is effective
before any subsequent I/O or config space accesses.
Without this, PCI device enumeration is unreliable.
[bhelgaas: changelog, comment]
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Add fallback compatibility string for R-Car Gen 2 family. This is in
keeping with the fallback scheme being adopted wherever appropriate for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add fallback compatibility string for R-Car Gen 2 family. This is in
keeping with the fallback scheme being adopted wherever appropriate for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add the "renesas,pcie-r8a7795" property for the R-Car H3 device to the
pcie-rcar driver.
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Harunobu Kurokawa <harunobu.kurokawa.dn@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Now that we can build on arm64, revert commit 7c537c67d2
("PCI: rcar: Build pcie-rcar.c only on ARM").
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The main purpose of this change is to avoid calling pci_ioremap_io() as
this is not available on arm64. However, instead of doing the range
parsing in this driver we can utilise of_pci_get_host_bridge_resources().
This is similar to changes made to the generic PCI host driver in commit
dbf9826d57 ("PCI: generic: Convert to DT resource parsing API")
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, all iProc PCIe root complexes use PAXB-based wrapper, with
an integrated on-chip Serdes to support external endpoint devices. On
newer iProc platforms, a PAXC-based wrapper is introduced, for connection
with internally emulated PCIe endpoint devices in the ASIC.
Add support for PAXC-based iProc PCIe root complex in the iProc PCIe core
driver. This change factors out common logic between PAXB and PAXC, and
uses tables to store register offsets that are different between PAXB and
PAXC. This allows the driver to be scaled to support subsequent PAXC
revisions in the future.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
For 32-bit config reads (size == 4), hisi_pcie_cfg_read() returned success
but never filled in the data we read.
Return the register data for 32-bit config reads.
Without this fix, PCI doesn't work at all because enumeration depends on
32-bit config reads. The driver was tested internally, but got broken in
the process of upstreaming, so this fixes the breakage.
Fixes: 500a1d9a43 ("PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
PCI interrupt lines start at 1, not at 0. So, creates additional one
interrupt when register for irq domain.
Error when PCIe devices have 4 INTx:
WARNING: CPU: 1 PID: 1 at kernel/irq/irqdomain.c:280
irq_domain_associate+0x17c/0x1cc()
error: hwirq 0x4 is too large for dummy
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Check TLP packet successful completion status. This fix the issue when
accessing multi-function devices in enumeration process, TLP will return
error when accessing non-exist function number. Returns PCI error code
instead of generic errno.
Tested on Ethernet adapter card with multi-functions.
[bhelgaas: simplify completion status checking code]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Requester ID should use the Root Port devfn and it should be always 0.
Previously we constructed the Requester ID using the *Completer* devfn,
i.e., the devfn of the Function we expect to respond to the config access.
This causes issues when accessing configuration space for devices other
than the Root Port.
Build the Requester ID using the Root Port devfn.
Tested on Ethernet adapter card with multi-functions.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
TLP_LOOP is 500 and the "loop" variable was a u8 so "loop < TLP_LOOP" is
always true. We only need this condition to work if there is a problem so
it would have been easy to miss this in testing.
Make it a normal for loop with "int i" instead of over thinking things and
making it complicated.
Fixes: 6bb4dd154ae8 ("PCI: altera: Add Altera PCIe host controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
We previously used of_get_named_gpio(), which ignores the OF flags cell, so
the reset GPIO defaulted to "active high." This doesn't work on the Toradex
Apalis SoM with Ixora base board, which has an active-low reset GPIO.
Use devm_gpiod_get_optional() instead so we pay attention to the active
high/low flag. This also adds support for GPIOs described via ACPI.
[bhelgaas: changelog]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The "%pap" format adds a "0x" prefix, so using "0x%pap" results in output
of "0x0x...". Drop the "0x" prefix in the format string.
[bhelgaas: changelog]
Signed-off-by: Dmitry V. Krivenok <krivenok.dmitry@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Commit b3a72384fe ("ARM/PCI: Replace pci_sys_data->align_resource with
global function pointer") removed the struct pci_sys_data dependency from
the ARM pcibios functions that are part of the common ARM PCI arch
back-end, e.g., pcibios_align_resource(), so that struct pci_sys_data has
now become data that is only used internally by the ARM bios32 layer, i.e.,
pci_common_init_dev(), and by host controllers drivers callbacks, e.g.,
pci_sys_data.setup, that rely on the ARM bios32 API to probe.
PCI host controller drivers that do not rely on ARM bios32 calls to probe
do not need to have the pci_bus.sysdata pointer field pointing at a struct
pci_sys_data anymore, therefore it can be removed from the respective
drivers data structures.
Remove the pci_sys_data structures from the host controller drivers that do
not rely on ARM bios32 interface to scan the PCI bus, completing the
pci_sys_data clean-up and removing the related dependency on arch/arm
specific data.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Will Deacon <will.deacon@arm.com>
CC: Rob Herring <robh@kernel.org>
If the DTB specifies dma-ranges, use those values. Otherwise, default to
the values that were previously hardcoded into the driver.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
We are in a context where we can sleep, and the PCIe reset gpio may be on
an I2C expander. Use the cansleep() variant when setting the GPIO value.
Based on a patch from Russell King for pci-mvebu.c.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
The hisi_pcie_probe() function is incorrectly marked as __init, as Kconfig
tells us:
WARNING: drivers/pci/host/built-in.o(.data+0x7780): Section mismatch in reference from the variable hisi_pcie_driver to the function .init.text:hisi_pcie_probe()
If the probe for this device gets deferred past the point where __init
functions are removed, or the device is unbound and then reattached to the
driver, we branch into uninitialized memory, which is bad.
Remove the __init annotation from hisi_pcie_probe() and
hisi_add_pcie_port().
Fixes: 500a1d9a43 ("PCI: hisi: Add HiSilicon SoC Hip05 PCIe driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Zhou Wang <wangzhou1@hisilicon.com>
PCIE_IPROC_BCMA does not require CONFIG_OF in Kconfig, but
CONFIG_PCIE_IPROC does, so we can get a warning when building for an ARM
platform without DT support:
warning: (PCIE_IPROC_PLATFORM && PCIE_IPROC_BCMA) selects PCIE_IPROC which has unmet direct dependencies (PCI && OF && (ARM || ARM64))
It turns out that CONFIG_PCIE_IPROC never needs to be enabled by a user
anyway, we can simply rely on it being selected implictly through either
PCIE_IPROC_PLATFORM or PCIE_IPROC_BCMA.
Fixes: 4785ffbdc9 ("PCI: iproc: Add BCMA PCIe driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
"pp->io" is an I/O resource, e.g., "[io 0x0000-0xffff]"; "pp->io_base" is
the CPU physical address of a region where the host bridge converts CPU
memory accesses into PCI I/O transactions.
Corrupting pp->io_base by assigning pp->io->start to it breaks access to
the PCI I/O space, as reported by Kishon.
Remove the invalid assignment.
[bhelgaas: changelog]
Fixes: 0021d22b73 ("PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT")
Reported-and-tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
* pci/host-altera:
PCI: altera: Add Altera PCIe MSI driver
PCI: altera: Add Altera PCIe host controller driver
ARM: Add msi.h to Kbuild
* pci/host-designware:
PCI: designware: Make "clocks" and "clock-names" optional DT properties
PCI: designware: Make driver arch-agnostic
ARM/PCI: Replace pci_sys_data->align_resource with global function pointer
PCI: designware: Use of_pci_get_host_bridge_resources() to parse DT
Revert "PCI: designware: Program ATU with untranslated address"
PCI: designware: Move calculation of bus addresses to DRA7xx
PCI: designware: Make "num-lanes" an optional DT property
PCI: designware: Require config accesses to be naturally aligned
PCI: designware: Simplify dw_pcie_cfg_read/write() interfaces
PCI: designware: Use exact access size in dw_pcie_cfg_read()
PCI: spear: Fix dw_pcie_cfg_read/write() usage
PCI: designware: Set up high part of MSI target address
PCI: designware: Make get_msi_addr() return phys_addr_t, not u32
PCI: designware: Implement multivector MSI IRQ setup
PCI: designware: Factor out MSI msg setup
PCI: Add msi_controller setup_irqs() method for special multivector setup
PCI: designware: Fix PORT_LOGIC_LINK_WIDTH_MASK
* pci/host-generic:
PCI: generic: Fix address window calculation for non-zero starting bus
PCI: generic: Pass starting bus number to pci_scan_root_bus()
PCI: generic: Allow multiple hosts with different map_bus() methods
arm64: dts: Drop linux,pci-probe-only from the Seattle DTS
powerpc/PCI: Fix lookup of linux,pci-probe-only property
PCI: generic: Fix lookup of linux,pci-probe-only property
of/pci: Add of_pci_check_probe_only to parse "linux,pci-probe-only"
* pci/host-imx6:
PCI: imx6: Add PCIE_PHY_RX_ASIC_OUT_VALID definition
PCI: imx6: Return real error code from imx6_add_pcie_port()
* pci/host-iproc:
PCI: iproc: Fix header comment "Corporation" misspelling
PCI: iproc: Add outbound mapping support
PCI: iproc: Update PCIe device tree bindings
PCI: iproc: Improve link detection logic
PCI: iproc: Fix PCIe reset logic
PCI: iproc: Call pci_fixup_irqs() for ARM64 as well as ARM
PCI: iproc: Remove unused struct iproc_pcie.irqs[]
PCI: iproc: Fix code comment to match code
* pci/host-mvebu:
PCI: mvebu: Remove code restricting accesses to slot 0
PCI: mvebu: Add PCI Express root complex capability block
PCI: mvebu: Improve clock/reset handling
PCI: mvebu: Use gpio_desc to carry around gpio
PCI: mvebu: Use devm_kcalloc() to allocate an array
PCI: mvebu: Use gpio_set_value_cansleep()
PCI: mvebu: Split port parsing and resource claiming from port setup
PCI: mvebu: Fix memory leaks and refcount leaks
PCI: mvebu: Move port parsing and resource claiming to separate function
PCI: mvebu: Use port->name rather than "PCIe%d.%d"
PCI: mvebu: Report full node name when reporting a DT error
PCI: mvebu: Use for_each_available_child_of_node() to walk child nodes
PCI: mvebu: Use of_get_available_child_count()
PCI: mvebu: Use exact config access size; don't read/modify/write
PCI: mvebu: Return zero for reserved or unimplemented config space
* pci/host-rcar:
PCI: rcar: Fix I/O offset for multiple host bridges
PCI: rcar: Set root bus nr to that provided in DT
PCI: rcar: Remove dependency on ARM-specific struct hw_pci
PCI: rcar: Make PCI aware of the I/O resources
PCI: rcar: Build pcie-rcar.c only on ARM
PCI: rcar: Build pci-rcar-gen2.c only on ARM
* pci/host-tegra:
PCI: tegra: Wrap static pgprot_t initializer with __pgprot()
* pci/host-xgene:
PCI/MSI: xgene: Remove msi_controller assignment
Add Altera PCIe MSI driver. This soft IP supports a configurable number of
vectors, which is a DTS parameter.
[bhelgaas: Kconfig depend on PCIE_ALTERA, typos, whitespace]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Layerscape PCIe has its own MSI implementation.
Register ls_pcie_msi_host_init() to avoid using DesignWare's MSI.
[bhelgaas: add comment]
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Both LS1043a and LS2080a are based on ARMv8 64-bit architecture and have
similar PCIe implementation. LUT is added to controller.
Add LS1043a and LS2080a support.
[bhelgaas: move unused field removal into separate patch, include DT update]
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com> (DT update)
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de> (DT update)
Removed unused node, dev, and bus fields from struct ls_pcie.
[bhelgaas: split into separate patch]
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update the ls_add_pcie_port() signature to keep it consistent with the
other DesignWare-based host drivers.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
For the LS1021a PCIe controller, some status registers are located in SCFG,
unlike other Layerscape devices.
Move SCFG-related code to ls1021_pcie_host_init() and rename
ls_pcie_link_up() to ls1021_pcie_link_up() because LTSSM status is also in
SCFG.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Layerscape PCIe controller supports root complex (RC) and endpoint (EP)
modes, which can be set by RCW.
If not in RC mode, return -ENODEV without claiming the controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ls_pcie_establish_link() does not do any real operation, except to wait for
the linkup establishment. In fact, this is not necessary. Moreover, each
PCIe controller not inserted device will increase the Linux startup time
about 200ms.
Remove ls_pcie_establish_link().
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously, dw_pcie_host_init() created the PCI host bridge with
pci_common_init_dev(), an ARM-specific function that supplies the ARM-
specific pci_sys_data structure as the PCI "sysdata".
Make pcie-designware.c arch-agnostic by reimplementing the functionality of
pci_common_init_dev() directly in dw_pcie_host_init().
Note that this changes the bridge sysdata from the ARM pci_sys_data to the
DesignWare pcie_port structure. This doesn't affect the ARM sysdata users
because they are all specific to non-DesignWare host bridges, which will
still have pci_sys_data.
[bhelgaas: changelog]
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Use the new of_pci_get_host_bridge_resources() API in place of the PCI OF
DT parser.
[bhelgaas: changelog]
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Revert f4c55c5a3f ("PCI: designware: Program ATU with untranslated
address").
Note that dra7xx_pcie_host_init() now modifies pp->io_base, but we still
need the original value for dw_pcie_setup() in the path below, so this adds
a new io_base_tmp member. It will be removed later when dw_pcie_setup() is
removed.
dra7xx_add_pcie_port
dw_pcie_host_init
pp->io_base = range.cpu_addr
pp->io_base_tmp = range.cpu_addr # <-- added
pp->ops->host_init
dra7xx_pcie_host_init # ops->host_init
pp->io_base &= DRA7XX_CPU_TO_BUS_ADDR # <-- modified
pci_common_init_dev(..., &dw_pci)
pcibios_init_hw
hw->setup
dw_pcie_setup # hw_pci.setup
pci_ioremap_io(..., pp->io_base_tmp) # <-- original addr required
[bhelgaas: changelog]
Tested-by: James Morse <james.morse@arm.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Tested-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Commit f4c55c5a3f ("PCI: designware: Program ATU with untranslated
address") added the calculation of PCI bus addresses in pcie-designware.c,
storing them in new fields added in struct pcie_port. This calculation is
done for every DesignWare user even though it only applies to DRA7xx.
Move the calculation of the bus addresses to the DRA7xx driver to allow the
rework of DesignWare to use the new DT parsing API.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Currently "num-lanes" is read in dw_pcie_host_init(), but it is only used
if we call dw_pcie_setup_rc() while bringing up the link. If the link has
already been brought up by firmware, we need not call dw_pcie_setup_rc(),
and "num-lanes" is unnecessary.
Only complain about "num-lanes" if we actually need it and we didn't find a
valid value.
[bhelgaas: changelog]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sanity checks on "addr" input parameter in dw_pcie_cfg_read() and
dw_pcie_cfg_write(). These checks make sure that accesses are aligned on
their size, e.g., a 4-byte config access is aligned on a 4-byte boundary.
[bhelgaas: changelog, set *val = 0 in failure case]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Callers of dw_pcie_cfg_read() and dw_pcie_cfg_write() previously had to
split the address into "addr" and "where". The callees assumed "addr" was
32-bit aligned (with zeros in the low two bits) and they used only the low
two bits of "where".
Accept the entire address in "addr" and drop the now-redundant "where"
argument. As an example, this replaces this:
int dw_pcie_cfg_read(void __iomem *addr, int where, int size, u32 *val)
*val = readb(addr + (where & 1));
with this:
int dw_pcie_cfg_read(void __iomem *addr, int size, u32 *val)
*val = readb(addr):
[bhelgaas: changelog, split access size change to separate patch]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_cfg_write() uses the exact 8-, 16-, or 32-bit access size
requested, but dw_pcie_cfg_read() previously performed a 32-bit read and
masked out the bits requested.
Use the exact access size in dw_pcie_cfg_read(). For example, if we want
an 8-bit read, use readb() instead of using readl() and masking out the 8
bits we need. This makes it symmetric with dw_pcie_cfg_write().
[bhelgaas: split into separate patch, set *val = 0 in failure case]
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The first argument of dw_pcie_cfg_read/write() is a 32-bit aligned address.
The second argument is the byte offset into a 32-bit word, and
dw_pcie_cfg_read/write() only look at the low two bits.
SPEAr13xx used dw_pcie_cfg_read() and dw_pcie_cfg_write() incorrectly: it
passed important address bits in the second argument, where they were
ignored.
Pass the complete 32-bit word address in the first argument and only the
2-bit offset into that word in the second argument.
Without this fix, SPEAr13xx host will never work with few buggy gen1 card
which connects with only gen1 host and also with any endpoint which would
generate a read request of more than 128 bytes.
[bhelgaas: changelog]
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.17+
Set up the high part of the MSI target address to allow the MSI target to
be above 4GB on 64bit and PAE systems.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
On ARM64, setting the root bus number to -1 causes probe failure.
Moreover, we should use the bus number specified in the DT as we could have
multiple PCIe controllers with different bus ranges.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car PCIe host controller driver uses pci_common_init_dev(), which is
ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
Based on 499733e0cc ("PCI: generic: Remove dependency on ARM-specific
struct hw_pci").
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Make PCI aware of the I/O resources.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The pcie-rcar.c driver (controlled by PCI_RCAR_GEN2_PCIE) uses struct
pci_sys_data and pci_ioremap_io(), which only exist on ARM. Building it on
other arches, e.g., arm64/shmobile, causes errors like this:
drivers/pci/host/pcie-rcar.c:138:52: warning: 'struct pci_sys_data' declared inside parameter list
drivers/pci/host/pcie-rcar.c:380:4: error: implicit declaration of function 'pci_ioremap_io' [-Werror=implicit-function-declaration]
Build pcie-rcar.c only on ARM.
[bhelgaas: changelog, split to separate pci-rcar-gen2 from pcie-rcar]
Reported-by: Wolfram Sang <wsa@the-dreams.de> (pci_ioremap_io())
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci-rcar-gen2.c driver (controlled by PCI_RCAR_GEN2) uses struct
pci_sys_data, which only exists on ARM. Building it on other arches, e.g.,
arm64/shmobile, causes errors like this:
drivers/pci/host/pci-rcar-gen2.c: In function 'rcar_pci_cfg_base': drivers/pci/host/pci-rcar-gen2.c:112:34: error: dereferencing pointer to incomplete type
struct rcar_pci_priv *priv = sys->private_data;
^
Build pci-rcar-gen2.c only on ARM.
[bhelgaas: changelog, split to separate pci-rcar-gen2 from pcie-rcar]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add the Altera PCIe host controller driver.
[bhelgaas: whitespace, fold in DT and maintainer updates, OF_PCI
dependency from Arnd]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org> (DT binding)
Certain SoCs require the PCIe outbound mapping to be configured in
software. Add support for those chips.
[jonmason: Use %pap format when printing size_t to avoid warnings in 32-bit
build.]
[arnd: Use div64_u64() instead of "%" to avoid __aeabi_uldivmod link error
in 32-bit build.]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As we continue to push of_node towards the outskirts of irq domains,
let's start tackling the case of msi_create_irq_domain and its little
friends.
This has limited impact in both PCI/MSI, platform MSI, and a few
drivers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-17-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make the offset from the beginning of the "reg" property be from the
starting bus number, rather than zero. Hoist the invariant size
calculation out of the mapping for loop.
Update host-generic-pci.txt to clarify the semantics of the "reg" property
with respect to non-zero starting bus numbers.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Now that we advertise a PCIe capability, the Linux PCI layer will not scan
the bus for devices other than in slot 0. This makes the work-around to
trap accesses to devices other than slot 0 unnecessary.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a PCI Express root complex capability block so the PCI layer identifies
the bridge as a PCI Express device.
We expose this as a version 1 PCIe capability block, with slot support. We
disable the clock power management capability as this depends on boards
wiring the CLKREQ# signal.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add an implementation to handle clock and reset handling that is compliant
with the PCIe specification. The clock should be running and stable for
100us prior to reset being released, and we should re-assert reset prior to
stopping the clock.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use a gpio_desc to carry around the gpio, so we can then make use of the
GPIOF_ACTIVE_LOW property rather than carrying that around as well. This
also avoids needing to use gpio_is_valid() to check whether we have a GPIO;
checking for a non-NULL descriptor is simpler.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rather than using devm_kzalloc() and multiplying the element and number,
use the provided devm_kcalloc() helper for this.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We are in a context where we can sleep, and the PCIe reset gpio may be on
an I2C expander. Use the cansleep() variant when setting the GPIO value.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Split the PCIe port DT parsing and resource claiming from setting up the
actual ports. This allows us to gather all the resources first, before
touching the hardware. This is important as some of these resources (such
as the GPIO for the PCIe reset) may defer probing.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The mvebu PCI port parsing is weak due to:
1) allocations via kasprintf() were not cleaned up when we encounter an
error or decide to skip the port.
2) kasprintf() wasn't checked for failure.
3) of_get_named_gpio_flags() returns EPROBE_DEFER if the GPIO is not
present, not devm_gpio_request_one().
4) the of_node was not being put when terminating the loop.
Fix these oversights.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Move the PCIe port parsing and resource claiming to a separate function in
preparation to add proper cleanup of claimed resources.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use the port->name string which we previously formatted when referring to
the name of a port, rather than manually creating the port name each time.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If we have a missing required property, report the full node name rather
than a vague "PCIe DT node" statement. This allows the exact node in error
to be identified immediately.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Thierry Reding