SDHCI controller in ls1043a and ls1046a generate 40-bit wide addresses
when doing DMA. Make sure that the corresponding dma mask is correctly
configured.
Context: when enabling smmu on these chips the following problem is
encountered: the smmu input address size is 48 bits so the dma mappings
for sdhci end up 48-bit wide. However, on these chips sdhci only use
40-bits of that address size when doing dma.
So you end up with a 48-bit address translation in smmu but the device
generates transactions with clipped 40-bit addresses, thus smmu context
faults are triggered. Setting up the correct dma mask fixes this
situation.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Convert to use of_match_node method to fix up eSDHC clock for
ls1046a/ls1012a/p1010. Also add eSDHC clock fixup for ls1021a
according to its datasheet. The maxmum speed for ls1021a eSDHC
high speed mode is 46.5MHz.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD clock should be disabled for clock value 0. It's not
right to just return. This may cause failure of signal
voltage switching.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC is not a standard SD host controller. SDHCI_CAPABILITIES_1
register address is 0x44 while it's 0x114 (ESDHC_CAPABILITIES_1)
for eSDHC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ls1046a datasheet specified that the max SD clock frequency
for eSDHC SDR104/HS200 was 167MHz, and the ls1012a datasheet
specified it's 125MHz for ls1012a. So this patch is to add the
limitation.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The loop to poll ESDHC_CLOCK_STABLE bit with mdelay would waste time
because the time to stabilize is much less than 1 ms. This patch is
to use udelay instead to avoid time wasting.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's observed that eSDHC needed delay between tuning cycles for
HS200 successful tuning. This patch is to set 1ms delay for that.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC uses tuning block for tuning procedure. So the tuning
block control register must be configured properly before tuning.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC supports signal voltage switch from 3.3v to 1.8v by
eSDHC_PROCTL[VOLT_SEL] bit. This bit changes the value of output
signal SDHC_VS, and there must be a control circuit out of eSDHC
to change the signal voltage according to SDHC_VS output signal.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eSDHC could select peripheral clock or platform clock as clock source by
the PCS bit of eSDHC Control Register, and this bit couldn't be reset by
software reset for all. In default, the platform clock is used. But we have
to use peripheral clock since it has a higher frequency to support eMMC
HS200 mode and SD UHS-I mode. This patch is to add peripheral clock support
and use it instead of platform clock if it's declared in eSDHC dts node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
mmc0: Card stuck in programming state! __mmc_switch
mmc0: error -110 whilst initialising MMC card
Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.
Signed-off-by: Michael Walle <michael@walle.cc>
Fixes: 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's use the SIMPLE_DEV_PM_OPS macro when declaring/assigning the system
PM callbacks, as the code gets simplified.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates the
sdhci-of-esdhc driver to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A previous patch had removed esdhc_of_platform_init() by mistake.
static void esdhc_of_platform_init(struct sdhci_host *host)
{
u32 vvn;
vvn = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS);
vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT;
if (vvn == VENDOR_V_22)
host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;
if (vvn > VENDOR_V_22)
host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;
}
This patch is used to fix it by add/remove some quirks according to
verdor version in probe.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Fixes: f4932cfd22 ("mmc: sdhci-of-esdhc: support both BE and LE host controller")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC doesn't have a standard power control register, so when
writing this register in stack we should do nothing to avoid
incorrect operation.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support little endian eSDHC controller, we redefine both BE and
LE IO accessors. In the new accessors, use ioread*/iowrite* instead
of in_be32/out_be32 and will select accessors according to endian
mode in probe function.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For eSDHC(version < 2.3), the pre divider only could divide base clock
by 2 at least. Add workaround for this to avoid unexpected issue.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Fixes: bd455029d0 ("mmc: sdhci-of-esdhc: Pre divider starts at 1")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable interrupt mode to detect card instead of polling mode
for P1020/P4080/P5020/P5040/T1040 by removing the quirk
SDHCI_QUIRK_BROKEN_CARD_DETECTION. This could improve data
transferring performance and avoid the call trace caused by
polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For PowerPC esdhc pre divider starts at 1, fixing the increases
the actual clock from 40KHz to 50 KHz.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In these drivers, the driver specific .remove function just a simple
wrapper of function sdhci_pltfm_unregister(). So remove these wrappers
and just set .remove to sdhci_pltfm_unregister().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 0718e59ae2 ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).
Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't need these hooks in order to insert code in these paths, we
can just provide our own handlers and call the main sdhci handlers as
appropriate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add sdhci_set_uhs_signaling() and always call the set_uhs_signaling
method. This avoids quirks being added into sdhci_set_uhs_signaling().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Move the setting of mmc->actual_clock to zero into the set_clock
handlers themselves. This will allow us to clean up the calling
logic for the set_clock() method, and turn sdhci_set_clock() into
a library function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We don't need implementations to do this, since the only time it's
necessary is when we change the clock, and the only place that happens
is in sdhci_do_set_ios(). So, move it there, and remove it from the
iMX platform backend.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than having platform_reset_enter/platform_reset_exit methods,
turn the core of the reset handling into a library function which
platforms can call at the appropriate moment in their (new) reset
method.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
We need a lot of imx6 specific things into common esdhc_set_clock
for support SD3.0 and eMMC DDR mode which is not needed for power pc
platforms, so esdhc_set_clock seems not so common anymore.
Instead of keeping add platform specfics things into this common API,
we choose to move that code into platform driver itself to handle.
This can also exclude the dependency between imx and power pc on this
headfile and is easy for maintain in the future.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add suppport to get voltage from device-tree node for esdhc host,
if voltage-ranges was specified in device-tree node we can get
ocr_mask instead of read from host capacity register. If not voltages
still can be get from host capacity register.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The P2020 has a non-standard implementation of the SDHCI_HOST_CONTROL
register. This patch adds a QUIRK in the SDHCI header to signal that
a host controller has a non-standard SDHCI_HOST_CONTROL register. The
patch adds a check to the function esdhc_writeb in file
sdhci-of-esdhc.c, where it checks if the write is done to the
SDHCI_HOST_CONTROL register and th host has the above mentioned QUIRK,
then the function simply returns instead of writing to the register.
The patch also detects if the processor is P2020 (by looking in dev
tree) and if so, adds the QUIRK to the host->quirk2
Signed-off-by: Oded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support of connecting an MMC media using an 8-bit
bus width connection to Freescale's P2020 H/W SDHC controller. During
the probe function, the generic function mmc_of_parse is called to
detect whether the controller is configured with 8-bit bus width.
Also, the generic function detects if the non-removable property is
set in the device tree. The function esdhc_pltfm_bus_width was added
because the bus width configuration is platform specific.
Signed-off-by: Oded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDCLK is divided down from the host controller clock. Host
controller clock may be different from the maximum SDCLK, so
get it from the platform, instead of just using the max SDCLK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a param to allow users of sdhci_pltfm to allocate private space
in calls to sdhci_pltfm_init+sdhci_pltfm_register. This is implemented
in the same way as sdhci does for its users.
None of the users have been migrated yet and are passing in zero to
retain their private allocation.
- todo: migrate clients to using allocation this way
- todo: remove priv variable once migration is complete
Also removed unused variable in sdhci_pltfm_init fn
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdhci_pltfm_data struct is never modified within the sdhci_pltfm
module. So make the pdata parameter to sdhci_pltfm_init and
sdhci_pltfm_register const. This allows drivers to declare their
sdhci_pltfm_data struct as const.
This patch also makes the sdhci_pltfm_data declarations const where
possible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
A-003500: False ADMA Error might be reported when ADMA is used for
multiple block read command with Stop at Block Gap. If PROCTL[SABGREQ]
is set when the particular block's data is received by the System side
logic before entire block (with CRC) data is received by the SD side
logic, and also if ADMA descriptor line is fetched at the same time,
then DMA engine might report false ADMA error. eSDHC might not be able
to Continue (PROCTL[CREQ]=1) after Stop at Block Gap.
This issue will impact the eSDHC IP VVN2.3.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Laurentiu Tudor