Commit Graph

323 Commits

Author SHA1 Message Date
Linus Torvalds 9e5fca251f Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
  IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
  IB/qib: Allow driver to load if PCIe AER fails
  IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
  IB/qib: Fix extra log level in qib_early_err()
  RDMA/cxgb4: Remove unnecessary KERN_<level> use
  RDMA/cxgb3: Remove unnecessary KERN_<level> use
  IB/core: Add link layer type information to sysfs
  IB/mlx4: Add VLAN support for IBoE
  IB/core: Add VLAN support for IBoE
  IB/mlx4: Add support for IBoE
  mlx4_en: Change multicast promiscuous mode to support IBoE
  mlx4_core: Update data structures and constants for IBoE
  mlx4_core: Allow protocol drivers to find corresponding interfaces
  IB/uverbs: Return link layer type to userspace for query port operation
  IB/srp: Sync buffer before posting send
  IB/srp: Use list_first_entry()
  IB/srp: Reduce number of BUSY conditions
  IB/srp: Eliminate two forward declarations
  IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
  IB: Replace EXTRA_CFLAGS with ccflags-y
  ...
2010-10-26 17:54:22 -07:00
Hagen Paul Pfeifer 732eacc054 replace nested max/min macros with {max,min}3 macro
Use the new {max,min}3 macros to save some cycles and bytes on the stack.
This patch substitutes trivial nested macros with their counterpart.

Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-10-26 16:52:12 -07:00
Roland Dreier 116e9535fe Merge branches 'amso1100', 'cma', 'cxgb3', 'cxgb4', 'ehca', 'iboe', 'ipoib', 'misc', 'mlx4', 'nes', 'qib' and 'srp' into for-next 2010-10-26 16:09:11 -07:00
Eli Cohen c3aa9b186b IPoIB: Set dev_id field of net_device
Use the net device's dev_id field to encode the port number of the pci
device.  This can be used to to associate a net device with the pci
device's port. The encoding is: dev_id = port - 1.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-10-23 13:35:48 -07:00
Eli Cohen 7b4c876961 IPoIB: Skip IBoE ports
IPoIB is IP-over-Infiniband link layer. In the case of IBoE, the link
layer is Ethernet and IP can work directly over Ethernet, so disable
IPoIB for non-IB_LINK_LAYER_INFINIBAND ports.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-10-13 09:38:11 -07:00
Christoph Lameter fed1db33fe IPoIB: Set pkt_type correctly for multicast packets (fix IGMP breakage)
IGMP processing is broken because the IPOIB does not set the
skb->pkt_type the right way for multicast traffic.  All incoming
packets are set to PACKET_HOST which means that igmp_recv() will
ignore the IGMP broadcasts/multicasts.

This in turn means that the IGMP timers are firing and are sending
information about multicast subscriptions unnecessarily.  In a large
private network this can cause traffic spikes.

Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-09-28 11:09:23 -07:00
Linus Torvalds 6ba74014c1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
  phy/marvell: add 88ec048 support
  igb: Program MDICNFG register prior to PHY init
  e1000e: correct MAC-PHY interconnect register offset for 82579
  hso: Add new product ID
  can: Add driver for esd CAN-USB/2 device
  l2tp: fix export of header file for userspace
  can-raw: Fix skb_orphan_try handling
  Revert "net: remove zap_completion_queue"
  net: cleanup inclusion
  phy/marvell: add 88e1121 interface mode support
  u32: negative offset fix
  net: Fix a typo from "dev" to "ndev"
  igb: Use irq_synchronize per vector when using MSI-X
  ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
  e1000e: Fix irq_synchronize in MSI-X case
  e1000e: register pm_qos request on hardware activation
  ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
  net: Add getsockopt support for TCP thin-streams
  cxgb4: update driver version
  cxgb4: add new PCI IDs
  ...

Manually fix up conflicts in:
 - drivers/net/e1000e/netdev.c: due to pm_qos registration
   infrastructure changes
 - drivers/net/phy/marvell.c: conflict between adding 88ec048 support
   and cleaning up the IDs
 - drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
   conflict (registration change vs marking it static)
2010-08-04 11:47:58 -07:00
Or Gerlitz 7a52b34b07 IPoIB: Fix world-writable child interface control sysfs attributes
Sumeet Lahorani <sumeet.lahorani@oracle.com> reported that the IPoIB
child entries are world-writable; however we don't want ordinary users
to be able to create and destroy child interfaces, so fix them to be
writable only by root.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-07-06 14:23:22 -07:00
Ben Hutchings 39827be26b IB/{nes, ipoib}: Pass supported flags to ethtool_op_set_flags()
Following commit 1437ce3983 "ethtool:
Change ethtool_op_set_flags to validate flags", ethtool_op_set_flags
takes a third parameter and cannot be used directly as an
implementation of ethtool_ops::set_flags.

Changes nes and ipoib driver to pass in the appropriate value.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-04 11:48:14 -07:00
Linus Torvalds f8965467f3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
  qlcnic: adding co maintainer
  ixgbe: add support for active DA cables
  ixgbe: dcb, do not tag tc_prio_control frames
  ixgbe: fix ixgbe_tx_is_paused logic
  ixgbe: always enable vlan strip/insert when DCB is enabled
  ixgbe: remove some redundant code in setting FCoE FIP filter
  ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
  ixgbe: fix header len when unsplit packet overflows to data buffer
  ipv6: Never schedule DAD timer on dead address
  ipv6: Use POSTDAD state
  ipv6: Use state_lock to protect ifa state
  ipv6: Replace inet6_ifaddr->dead with state
  cxgb4: notify upper drivers if the device is already up when they load
  cxgb4: keep interrupts available when the ports are brought down
  cxgb4: fix initial addition of MAC address
  cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
  cnic: Convert cnic_local_flags to atomic ops.
  can: Fix SJA1000 command register writes on SMP systems
  bridge: fix build for CONFIG_SYSFS disabled
  ARCNET: Limit com20020 PCI ID matches for SOHARD cards
  ...

Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).

Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
2010-05-20 21:04:44 -07:00
Or Gerlitz d414371795 IPoIB: Allow disabling/enabling TSO on the fly through ethtool
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-04-21 17:17:30 -07:00
David S. Miller 871039f02f Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/stmmac/stmmac_main.c
	drivers/net/wireless/wl12xx/wl1271_cmd.c
	drivers/net/wireless/wl12xx/wl1271_main.c
	drivers/net/wireless/wl12xx/wl1271_spi.c
	net/core/ethtool.c
	net/mac80211/scan.c
2010-04-11 14:53:53 -07:00
Jiri Pirko 22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Jiri Pirko 3e4aa12f8a ipoib: remove addrlen check for mc addresses
Finally this bit can be removed. Currently, after the bonding driver is
changed/fixed (32a806c194 net-next-2.6),
that's not possible for an addr with different length than dev->addr_len
to be present in list. Removing this check as in new mc_list there will be
no addrlen in the record.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-22 18:33:11 -07:00
Or Gerlitz a48f509b26 IPoIB: Include return code in trace message for ib_post_send() failures
Print the return code of ib_post_send() if it fails to make these
debugging messages more useful.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-03-11 13:43:11 -08:00
Eli Cohen f0dc117abd IPoIB: Fix TX queue lockup with mixed UD/CM traffic
The IPoIB UD QP reports send completions to priv->send_cq, which is
usually left unarmed; it only gets armed when the number of
outstanding send requests reaches the size of the TX queue. This
arming is done only in the send path for the UD QP.  However, when
sending CM packets, the net queue may be stopped for the same reasons
but no measures are taken to recover the UD path from a lockup.

Consider this scenario: a host sends high rate of both CM and UD
packets, with a TX queue length of N.  If at some time the number of
outstanding UD packets is more than N/2 and the overall outstanding
packets is N-1, and CM sends a packet (making the number of
outstanding sends equal N), the TX queue will be stopped.  When all
the CM packets complete, the number of outstanding packets will still
be higher than N/2 so the TX queue will not be restarted.

Fix this by calling ib_req_notify_cq() when the queue is stopped in
the CM path.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-03-11 13:37:11 -08:00
Linus Torvalds 3ff1562ea4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
  IB/srp: Clean up error path in srp_create_target_ib()
  IB/srp: Split send and recieve CQs to reduce number of interrupts
  RDMA/nes: Add support for KR device id 0x0110
  IB/uverbs: Use anon_inodes instead of private infinibandeventfs
  IB/core: Fix and clean up ib_ud_header_init()
  RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
  RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
  RDMA/cxgb3: Increase the max CQ depth
  RDMA/cxgb3: Doorbell overflow avoidance and recovery
  IB/core: Pack struct ib_device a little tighter
  IB/ucm: Clean whitespace errors
  IB/ucm: Increase maximum devices supported
  IB/ucm: Use stack variable 'base' in ib_ucm_add_one
  IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
  IB/umad: Clean whitespace
  IB/umad: Increase maximum devices supported
  IB/umad: Use stack variable 'base' in ib_umad_init_port
  IB/umad: Use stack variable 'devnum' in ib_umad_init_port
  IB/umad: Remove port_table[]
  IB/umad: Convert *cdev to cdev in struct ib_umad_port
  ...
2010-03-03 07:33:17 -08:00
Jiri Pirko 6c74651c3b ipoib: returned back addrlen check for mc addresses
Apparently bogus mc address can break IPOIB multicast processing. Therefore
returning the check for addrlen back until this is resolved in bonding (I don't
see any other point from where mc address with non-dev->addr_len length can came
from).

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 01:34:28 -08:00
Jiri Pirko fbf219f1c8 infiniband: convert to use netdev_for_each_mc_addr
Due to the loop complexicity in nes_nic.c, I'm using char* to copy mc addresses
to it.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-26 04:22:27 -08:00
Alexey Dobriyan 3ffe533c87 ipv6: drop unused "dev" arg of icmpv6_send()
Dunno, what was the idea, it wasn't used for a long time.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-18 14:30:17 -08:00
Or Gerlitz 757bebb3f9 IPoIB: Remove TX moderation settings from ethtool support
As of commit f56bcd8 ("IPoIB: Use separate CQ for UD send
completions"), there are no TX interrupts.  Change the ethtool code
not to report TX moderation settings, so users will not be misled to
think they can control TX interrupt moderation.  Pointed out by Alex
Vainman <alexv@voltaire.com>

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2010-02-11 15:40:40 -08:00
David J. Wilder 0cd4d0fd9b IPoIB: Clear ipoib_neigh.dgid in ipoib_neigh_alloc()
IPoIB can miss a change in destination GID under some conditions.  The
problem is caused when ipoib_neigh->dgid contains a stale address.
The fix is to set ipoib_neigh->dgid to zero in ipoib_neigh_alloc().

This can happen when a system using bonding on its IPoIB interfaces
has switched its active interface from interface A to B and back to A.
The system that fails over will not correctly processes the 2nd
address change, as described below.

When an address has changed neighbor->ha is updated with the new
address.  Each neighbor has an associated ipoib_neigh.
ipoib_neigh->dgid also holds a copy of the remote node's hardware
address.  When an address changes neighbor->ha is updated by the
network layer (arp code) with the new address.  IPoIB detects this
change in ipoib_start_xmit() by comparing neighbor->ha with
ipoib_neigh->dgid.  The bug is that ipoib_neigh->dgid may already
contain the new address (A) thus the change from B to A is missed by
ipoib.  Here is the sequence of events:

    ipoib_neigh->dgid = A  and  neighbor->ha = A

The address is switched to B (the first switch)

    neighbor->ha = B

The change is seen in ipoib_start_xmit() -- neighbor->ha !=
ipoib_neigh->dgid so ipoib_neigh is released, and a new one is
allocated.

The allocator may return the same chunk of memory that was just
released, therefore ipoib_neigh->dgid still contains A at this point.

ipoib_neigh->dgid should be updated in neigh_add_path(), but if the
following conditions are true dgid is not updated:

        1) __path_find() returns a path
        2) path->ah is NULL

The remote system now switches from address B to A, neighbor->ha is
updated to A.

Now we have again : ipoib_neigh->dgid = A  and  neighbor->ha = A

Since the addresses are the same ipoib won't process the change in
address.  Fix this by zeroing out the dgid field when allocating a new
struct ipoib_neigh.

Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-12-09 10:03:00 -08:00
Linus Torvalds d7757be133 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IPoIB: Don't turn on carrier for a non-active port
  IB/mthca: Fix access to freed memory in catastrophic event handling
  mlx4_core: Pass cache line size to device FW
  RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
  IB/mad: Fix lock-lock-timer deadlock in RMPP code
2009-09-24 17:06:01 -07:00
Moni Shoua 5ee9512084 IPoIB: Don't turn on carrier for a non-active port
Multicast joins can succeed even if the IB port is down.  This happens
when the SM runs on the same port with the requesting port.  However,
IPoIB calls netif_carrier_on() when the join of the broadcast group
succeeds, without caring about the state of the IB port.  The result
is an IPoIB interface in RUNNING state but without an active IB port
to support it.

If a bonding interface uses this IPoIB interface as a slave it might
not detect that this slave is almost useless and failover
functionality will be damaged.  The fix checks the state of the IB
port in the carrier_task before calling netif_carrier_on().

Adresses: https://bugs.openfabrics.org/show_bug.cgi?id=1726
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-24 12:01:05 -07:00
Linus Torvalds d7e9660ad9 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
  netxen: update copyright
  netxen: fix tx timeout recovery
  netxen: fix file firmware leak
  netxen: improve pci memory access
  netxen: change firmware write size
  tg3: Fix return ring size breakage
  netxen: build fix for INET=n
  cdc-phonet: autoconfigure Phonet address
  Phonet: back-end for autoconfigured addresses
  Phonet: fix netlink address dump error handling
  ipv6: Add IFA_F_DADFAILED flag
  net: Add DEVTYPE support for Ethernet based devices
  mv643xx_eth.c: remove unused txq_set_wrr()
  ucc_geth: Fix hangs after switching from full to half duplex
  ucc_geth: Rearrange some code to avoid forward declarations
  phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
  drivers/net/phy: introduce missing kfree
  drivers/net/wan: introduce missing kfree
  net: force bridge module(s) to be GPL
  Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
  ...

Fixed up trivial conflicts:

 - arch/x86/include/asm/socket.h

   converted to <asm-generic/socket.h> in the x86 tree.  The generic
   header has the same new #define's, so that works out fine.

 - drivers/net/tun.c

   fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
   switched over to using 'tun->socket.sk' instead of the redundantly
   available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
   to the TUN driver") which added a new 'tun->sk' use.

   Noted in 'next' by Stephen Rothwell.
2009-09-14 10:37:28 -07:00
Jason Gunthorpe 5e47596bee IPoIB: Check multicast address format
Check that the format of multicast link addresses is correct before
taking them from dev->mc_list to priv->multicast_list.  This way we
never try to send a bogus address to the SA, which prevents badness
from erronous 'ip maddr addr add', broken bonding drivers, etc.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:23:40 -07:00
Roland Dreier 721d67cdca IPoIB: Drop priv->lock before calling ipoib_send()
IPoIB currently must use irqsave locking for priv->lock, since it is
taken from interrupt context in one path.  However, ipoib_send() does
skb_orphan(), and the network stack locking is not IRQ-safe.
Therefore we need to make sure we don't hold priv->lock when calling
ipoib_send() to avoid lockdep warnings (the code was almost certainly
safe in practice, since the only code path that takes priv->lock from
interrupt context would never call into the network stack).

Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:23:40 -07:00
Roland Dreier cd0bcf4cb9 IPoIB: Remove unused <rdma/ib_cache.h> includes
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-09-05 20:23:38 -07:00
Eric Dumazet 451f144398 drivers: Kill now superfluous ->last_rx stores
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02 23:07:36 -07:00
Eric Dumazet adf30907d6 net: skb->dst accessors
Define three accessors to get/set dst attached to a skb

struct dst_entry *skb_dst(const struct sk_buff *skb)

void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)

void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;

Delete skb->dst field

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-03 02:51:04 -07:00
Eric Dumazet 86d15cd833 net: unset IFF_XMIT_DST_RELEASE for qeth and ipoib
Last two drivers that need skb->dst in their start_xmit() function

Tell dev_hard_start_xmit() to no release it by unsetting  IFF_XMIT_DST_RELEASE

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-30 23:04:46 -07:00
Eric W. Biederman 26574401fe net: Fix ipoib rtnl_lock sysfs deadlock.
Network device sysfs files that grab the rtnl_lock unconditionally
will deadlock if accessed when the network device is being
unregistered.  So use trylock and syscall_restart to avoid this
deadlock.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-18 22:15:59 -07:00
Yossi Etigin e028cc55cc IPoIB: Disable NAPI while CQ is being drained
If NAPI is enabled while IPoIB's CQ is being drained, it creates a
race on priv->ibwc between ipoib_poll() and ipoib_drain_cq(), leading
to memory corruption.

The solution is to enable/disable NAPI in ipoib_ib_dev_{open/stop}()
instead of in ipoib_{open/stop}(), and sync NAPI on the INITIALIZED
flag instead on the ADMIN_UP flag. This way NAPI will be disabled when
ipoib_drain_cq() is called.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1587>.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-04-20 13:58:08 -07:00
Roland Dreier edb5abb1e2 IPoIB: Avoid free_netdev() BUG when destroying a child interface
We have to release the RTNL before calling free_netdev() so that the
device state has a chance to become NETREG_UNREGISTERED.  Otherwise
when removing a child interface, we hit the BUG() that tests the
device state in free_netdev().

Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-03-31 10:22:32 -07:00
Linus Torvalds 13220a94d3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
  ixgbe: Allow Priority Flow Control settings to survive a device reset
  net: core: remove unneeded include in net/core/utils.c.
  e1000e: update version number
  e1000e: fix close interrupt race
  e1000e: fix loss of multicast packets
  e1000e: commonize tx cleanup routine to match e1000 & igb
  netfilter: fix nf_logger name in ebt_ulog.
  netfilter: fix warning in ebt_ulog init function.
  netfilter: fix warning about invalid const usage
  e1000: fix close race with interrupt
  e1000: cleanup clean_tx_irq routine so that it completely cleans ring
  e1000: fix tx hang detect logic and address dma mapping issues
  bridge: bad error handling when adding invalid ether address
  bonding: select current active slave when enslaving device for mode tlb and alb
  gianfar: reallocate skb when headroom is not enough for fcb
  Bump release date to 25Mar2009 and version to 0.22
  r6040: Fix second PHY address
  qeth: fix wait_event_timeout handling
  qeth: check for completion of a running recovery
  qeth: unregister MAC addresses during recovery.
  ...

Manually fixed up conflicts in:
	drivers/infiniband/hw/cxgb3/cxio_hal.h
	drivers/infiniband/hw/nes/nes_nic.c
2009-03-26 15:54:36 -07:00
Stephen Hemminger fe8114e8e1 infiniband: convert ipoib to net_device_ops
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 19:19:14 -07:00
Jack Morgenstein 71d98b4628 IPoIB: In unicast_arp_send(), only free newly-created paths
If path_rec_start() returns error, call path_free() only if the path
was newly-created.  If we free an existing path whose valid flag was zero,
(but do not detach it from the list) we cause corruption of the
path list (of which it is a member), and get a kernel crash.

The simplest solution is to not free an existing path -- just leave it
in the list as-is (i.e., with its valid flag cleared).

Thanks to Yossi Etigin of Voltaire for identifying the problem flow
which caused the kernel crash.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moni Shua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-02-17 14:51:47 -08:00
Ben Hutchings 288379f050 net: Remove redundant NAPI functions
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-21 14:33:50 -08:00
Yossi Etigin 3c20962086 IPoIB: Do not print error messages for multicast join retries
When IPoIB tries to join a multicast group, and the SA module's SM
address handle is NULL (because of an SM change, etc), the join
returns with -EAGAIN status.  In that case, don't print an error
message unless multicast debugging is enabled.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-16 13:42:59 -08:00
Roland Dreier cbbe1efa49 IPoIB: Fix deadlock between ipoib_open() and child interface create
Fix a deadlock between child interface creation/deletion and ipoib
start/stop.  The former takes vlan_mutex, and then might take RTNL via
register_netdev()/unregister_netdev().  The latter is executed with
RTNL held, and tries to take vlan_mutex, which can lead to an AB-BA
deadlock.

Fix this by having the child interface creation/deletion code take the
RTNL first so vlan_mutex always nests inside RTNL.  We can use
register_netdevice() for child interfaces because we form the
interface name from the parent interface and hence don't need the '%'
expansion of register_netdev().

Reported-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-14 21:44:39 -08:00
Roland Dreier b8a1b1ce14 IPoIB: Fix hang in napi_disable() if P_Key is never found
After commit fe25c561 ("IPoIB: Don't enable NAPI when it's already
enabled"), if an interface is brought up but the corresponding P_Key
never appears, then ipoib_stop() will hang in napi_disable(), because
ipoib_open() returns before it does napi_enable().

Fix this by changing ipoib_open() to call napi_enable() even if the
P_Key isn't present.

Reported-by: Yossi Etigin <yosefe@Voltaire.COM>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-14 14:55:41 -08:00
Yossi Etigin 50df48f59d IPoIB: Do not join broadcast group if interface is brought down
Because the ipoib_workqueue is not flushed when ipoib interface is
brought down, ipoib_mcast_join() may trigger a join to the broadcast
group after priv->broadcast was set to NULL (during cleanup).  This
will cause the system to be a member of the broadcast group when
interface is down.  As a side effect, this breaks the optimization of
setting the Q_key only when joining the broadcast group.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-12 19:28:42 -08:00
Yossi Etigin a50df398cd IPoIB: Fix loss of connectivity after bonding failover on both sides
Fix bonding failover in the case both peers failover and the
gratuitous ARP is lost.  In that case, the sender side will create an
ipoib_neigh and issue a path request with the old GID first.  When
skb->dst->neighbour->ha changes due to ARP refresh, this ipoib_neigh
will not be added to the path->list of the path of the new GID,
because the ipoib_neigh already exists.  It will not have an AH
either, because of sender-side failover.  Therefore, it will not get
an AH when the path is resolved.

The solution here is to compare GIDs in ipoib_start_xmit() even if
neigh->ah is invalid.  Comparing with an uninitialized value of
neigh->dgid should be fine, since a spurious match is harmless (and
astronomically unlikely too).

Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-01-09 14:05:11 -08:00
Neil Horman 908a7a16b8 net: Remove unused netdev arg from some NAPI interfaces.
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter.  This patch cleans up that api by
properly removing it..

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-22 20:43:12 -08:00
David S. Miller 198d6ba4d7 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:

	drivers/isdn/i4l/isdn_net.c
	fs/cifs/connect.c
2008-11-18 23:38:23 -08:00
Yossi Etigin ff79ae8083 IPoIB: Fix crash in path_rec_completion()
Fix a crash in path_rec_completion() during an SM up/down loop.  If
more than one path record request is issued, the first completion
releases path->done, allowing ipoib_flush_paths() to free the path,
and thus corrupting it for the second completion.

Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") added the field path->valid and changed the test "if
(!path)" to "if (!path || !path->valid)".  This change made it
possible for a path with an outstanding query to pass the test and
issue another query on the same path.  Having two queries on the same
path leads to a crash.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1325>.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-11-12 10:24:39 -08:00
Yossi Etigin 93a3ab939b IPoIB: Fix hang in ipoib_flush_paths()
ipoib_flush_paths() can hang during an SM up/down loop: if
path_rec_start() fails (for instance, because there is no sm_ah), the
path is still added to the path list by neigh_add_path().  Then,
ipoib_flush_paths() will wait for path->done, but it will never
complete because the request was not issued at all.  Fix this by
completing path->done if issuing the query fails.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1329>.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-11-12 10:24:38 -08:00
Yossi Etigin fe25c56190 IPoIB: Don't enable NAPI when it's already enabled
If a P_Key is not present when an interface is created, ipoib_open()
will return after doing napi_enable().  ipoib_open() will be called
again from ipoib_pkey_poll() when the P_Key appears, after NAPI has
already been enabled, and try to enable it again. This triggers a
BUG_ON() in napi_enable().

Fix this by moving the call to napi_enable() to after the test for
P_Key presence.

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-11-12 10:24:36 -08:00
Harvey Harrison 5b095d9892 net: replace %p6 with %pI6
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-29 12:52:50 -07:00
Harvey Harrison 8c165a8383 infiniband: remove IPOIB_GID_RAW_ARG, IPOIB_GID_ARG, IPOIB_GID_FMT
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-28 23:02:37 -07:00
Harvey Harrison fcace2fe7a infiniband: ipoib replace IPOIB_GID_FMT with %p6
Replace all uses of IPOIB_GID_FMT, IPOIB_GID_RAW_ARG() and IPOIB_GID_ARG()

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-28 23:02:36 -07:00
Or Gerlitz 83bb63f62b IPoIB: Set netdev offload features properly for child (VLAN) interfaces
Child devices were created without any offload features set, fix this by
moving the code that computes the features into generic function which is
now called through non-child and child device creation.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>

-- v1 has a bug where the 'result' flag in ipoib_vlan_add may be used uninitialized
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-10-22 15:49:49 -07:00
Or Gerlitz 70c9c0db54 IPoIB: Clean up ethtool support
Add a get_rx_csum method.  Remove the driver's own get_tso method, as
the ethtool kernel code uses the default one if nothing is provided.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-10-22 15:49:29 -07:00
Roland Dreier 2767840a5c IPoIB: Always initialize poll_timer to avoid crash on unload
ipoib_ib_dev_stop() does del_timer_sync(&priv->poll_timer), but if a
P_key for an interface is not found, poll_timer is not initialized, so
this leads to a crash or hang.  Fix this by moving where poll_timer is
initialized to ipoib_ib_dev_init(), which is always called.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1172>.

Debugged-by: Yosef Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-10-10 15:58:52 -07:00
Roland Dreier 943c246e9b IPoIB: Use netif_tx_lock() and get rid of private tx_lock, LLTX
Currently, IPoIB is an LLTX driver that uses its own IRQ-disabling
tx_lock.  Not only do we want to get rid of LLTX, this actually causes
problems because of the skb_orphan() done with this tx_lock held: some
skb destructors expect to be run with interrupts enabled.

The simplest fix for this is to get rid of the driver-private tx_lock
and stop using LLTX.  We kill off priv->tx_lock and use
netif_tx_lock[_bh]() instead; the patch to do this is a tiny bit
tricky because we need to update places that take priv->lock inside
the tx_lock to disable IRQs, rather than relying on tx_lock having
already disabled IRQs.

Also, there are a couple of places where we need to disable BHs to
make sure we have a consistent context to call netif_tx_lock() (since
we no longer can use _irqsave() variants), and we also have to change
ipoib_send_comp_handler() to call drain_tx_cq() through a timer rather
than directly, because ipoib_send_comp_handler() runs in interrupt
context and drain_tx_cq() must run in BH context so it can call
netif_tx_lock().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-09-30 10:36:21 -07:00
Roland Dreier c9da4bad5b IPoIB: Fix crash when path record fails after path flush
Commit ee1e2c82 ("IPoIB: Refresh paths instead of flushing them on SM
change events") changed how paths are flushed on an SM event.  This
change introduces a problem if the path record query triggered by
fails, causing path->ah to become NULL.  A later successful path query
will then trigger WARN_ON() in path_rec_completion(), and crash
because path->ah has already been freed, so the ipoib_put_ah() inside
the lock in path_rec_completion() may actually drop the last reference
(contrary to the comment that claims this is safe).

Fix this by updating path->ah and freeing old_ah only when the path
record query is successful.  This prevents the neighbour AH and that
path AH from getting out of sync.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1194>

Reported-by: Rabah Salem <ravah@mellanox.com>
Debugged-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-09-25 15:26:15 -07:00
Yossi Etigin e8224e4b80 IPoIB: Fix deadlock on RTNL between bcast join comp and ipoib_stop()
Taking rtnl_lock in ipoib_mcast_join_complete() causes a deadlock with
ipoib_stop().  We avoid it by scheduling the piece of code that takes
the lock on ipoib_workqueue instead of executing it directly.  This
works because we only flush the ipoib_workqueue with the RTNL not held.

The deadlock happens because ipoib_stop() calls ipoib_ib_dev_down()
which calls ipoib_mcast_dev_flush(), which calls ipoib_mcast_free(),
which calls ipoib_mcast_leave(). The latter calls
ib_sa_free_multicast(), and this waits until the multicast completion
handler finishes.  This handler is ipoib_mcast_join_complete(), which
waits for the rtnl_lock(), which was already taken by ipoib_stop().

This bug was introduced in commit a77a57a1 ("IPoIB: Fix deadlock on
RTNL in ipoib_stop()").

Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-09-16 11:57:45 -07:00
Roland Dreier a77a57a1a2 IPoIB: Fix deadlock on RTNL in ipoib_stop()
Commit c8c2afe3 ("IPoIB: Use rtnl lock/unlock when changing device
flags") added a call to rtnl_lock() in ipoib_mcast_join_task(), which
is run from the ipoib_workqueue.  However, ipoib_stop() (which is run
inside rtnl_lock()) flushes this workqueue, which leads to a deadlock
if the join task is pending.

Fix this by simply not flushing the workqueue from ipoib_stop().  It
turns out that we really don't care about workqueue tasks running
during or after ipoib_stop(), as long as we make sure to flush the
workqueue before unregistering a netdev.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1114>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-08-19 15:01:32 -07:00
David J. Wilder b1404069f6 IPoIB/cm: Use vmalloc() to allocate rx_rings
There are users that are running UDP applications that require a large
receive queue size in order to get good performance.  To prevent
allocation failures for rx_rings when using non-SRQ mode and large
recv_queue_size (1K or larger), use vmalloc() instead of kcalloc() to
alocate rx_rings.

Signed-off-by: David Wilder <dwilder@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-08-08 15:51:29 -07:00
Roland Dreier e08198169e IPoIB/cm: Set correct SG list in ipoib_cm_init_rx_wr()
wr->sg_list should be set to the sge pointer passed in, not
priv->cm.rx_sge.

Reported-by: Hoang-Nam Nguyen <HNGUYEN@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-30 07:21:46 -07:00
Roland Dreier 9905922446 IPoIB: Correct help text for INFINIBAND_IPOIB_DEBUG
The help text for INFINIBAND_IPOIB_DEBUG refers to "ipoib_debugfs,"
which no longer exists.  Correct this to talk about the files under
debugfs that are really created.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-24 20:37:25 -07:00
Roland Dreier 99c3a5a9e3 IPoIB/cm: Connected mode is no longer EXPERIMENTAL
Connected mode is now tested and used by lots of people.  No need to
hide it under CONFIG_EXPERIMENTAL.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-24 20:37:25 -07:00
Or Gerlitz 01b3fc8b15 IPoIB: Include err code in trace message for ib_sa_path_rec_get() failures
Print the return code of ib_sa_path_rec_get() if it fails to help
debug errors.

Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-22 14:18:34 -07:00
David S. Miller 49997d7515 Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	Documentation/powerpc/booting-without-of.txt
	drivers/atm/Makefile
	drivers/net/fs_enet/fs_enet-main.c
	drivers/pci/pci-acpi.c
	net/8021q/vlan.c
	net/iucv/iucv.c
2008-07-18 02:39:39 -07:00
David S. Miller b9e4085768 netdev: Do not use TX lock to protect address lists.
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-15 00:15:08 -07:00
David S. Miller e308a5d806 netdev: Add netdev->addr_list_lock protection.
Add netif_addr_{lock,unlock}{,_bh}() helpers.

Use them to protect operations that operate on or read
the network device unicast and multicast address lists.

Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-07-15 00:13:44 -07:00
Eli Cohen bc3a290b51 IPoIB: Double default RX/TX ring sizes
Increase IPoIB ring sizes to twice their original sizes (RX: 128->256,
TX: 64->128) to act as a shock absorber for high traffic peaks.  With
the current settings, we have seen cases that there are many calls to
netif_stop_queue(), which causes degradation in throughput.  Also,
larger receive buffer sizes help IPoIB in CM mode to avoid experiencing
RNR NAK conditions due to insufficient receive buffers at the SRQ.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:52 -07:00
Eli Cohen e112373fd6 IPoIB/cm: Reduce connected mode TX object size
Since IPoIB connected mode does not NETIF_F_SG, we only have one DMA
mapping per send, so we don't need a mapping[] array.  Define a new
struct with a single u64 mapping member and use it for the CM tx_ring.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:52 -07:00
Eli Cohen bd3606715e IPoIB: Use dev_set_mtu() to change mtu
When the driver sets the MTU of the net device outside of its
change_mtu method, it should make use of dev_set_mtu() instead of
directly setting the mtu field of struct netdevice.  Otherwise
functions registered to be called upon MTU change will not get called
(this is done through call_netdevice_notifiers() in dev_set_mtu()).

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:51 -07:00
Eli Cohen c8c2afe360 IPoIB: Use rtnl lock/unlock when changing device flags
Use of this lock is required to synchronize changes to the netdvice's
data structs.  Also move the call to ipoib_flush_paths() after the
modification of the netdevice flags in set_mode().

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:51 -07:00
Roland Dreier 9eae554c17 IPoIB: Get rid of ipoib_mcast_detach() wrapper
ipoib_mcast_detach() does nothing except call ib_detach_mcast(), so just
use the core API in the one place that does a multicast group detach.

add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-105 (-105)
function                                     old     new   delta
ipoib_mcast_leave                            357     319     -38
ipoib_mcast_detach                            67       -     -67

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:50 -07:00
Eli Cohen d0de13622d IPoIB: Only set Q_Key once: after joining broadcast group
The current code will set the Q_Key for any join of a non-sendonly
multicast group.  The operation involves a modify QP operation, which
is fairly heavyweight, and is only really required after the join of
the broadcast group.  Fix this by adding a parameter to ipoib_mcast_attach()
to control when the Q_Key is set.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:50 -07:00
Eli Cohen 5892eff91a IPoIB: Remove priv->mcast_mutex
No need for a mutex around calls to ib_attach_mcast/ib_detach_mcast
since these operations are synchronized at the HW driver layer.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:50 -07:00
Eli Cohen c03d4731b5 IPoIB: Remove unused IPOIB_MCAST_STARTED code
The IPOIB_MCAST_STARTED flag is not used at all since commit b3e2749b
("IPoIB: Don't drop multicast sends when they can be queued"), so
remove it.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:50 -07:00
Moni Shoua ee1e2c82c2 IPoIB: Refresh paths instead of flushing them on SM change events
The patch tries to solve the problem of device going down and paths being
flushed on an SM change event. The method is to mark the paths as candidates for
refresh (by setting the new valid flag to 0), and wait for an ARP
probe a new path record query.

The solution requires a different and less intrusive handling of SM
change event. For that, the second argument of the flush function
changes its meaning from a boolean flag to a level.  In most cases, SM
failover doesn't cause LID change so traffic won't stop.  In the rare
cases of LID change, the remote host (the one that hadn't changed its
LID) will lose connectivity until paths are refreshed. This is no
worse than the current state.  In fact, preventing the device from
going down saves packets that otherwise would be lost.

Signed-off-by: Moni Levy <monil@voltaire.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:49 -07:00
Vladimir Sokolovsky af40da894e IPoIB: add LRO support
Add "ipoib_use_lro" module parameter to enable LRO and an
"ipoib_lro_max_aggr" module parameter to set the max number of packets
to be aggregated.  Make LRO controllable and LRO statistics accessible
through ethtool.

Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:48 -07:00
Ron Livne 1240673405 IPoIB: Use multicast loopback blocking if available
Set IB_QP_CREATE_BLOCK_MULTICAST_LOOPBACK for IPoIB's UD QPs if
supported by the underlying device.  This creates an improvement of up
to 39% in bandwidth when sending multicast packets with IPoIB, and an
improvment of 12% in cpu usage.

Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:48 -07:00
Roland Dreier a7d834c4bc IPoIB/cm: Fix racy use of receive WR/SGL in ipoib_cm_post_receive_nonsrq()
For devices that don't support SRQs, ipoib_cm_post_receive_nonsrq() is
called from both ipoib_cm_handle_rx_wc() and ipoib_cm_nonsrq_init_rx(),
and these two callers are not synchronized against each other.
However, ipoib_cm_post_receive_nonsrq() always reuses the same receive
work request and scatter list structures, so multiple callers can end
up stepping on each other, which leads to posting garbled work
requests.

Fix this by having the caller pass in the ib_recv_wr and ib_sge
structures to use, and allocating new local structures in
ipoib_cm_nonsrq_init_rx().

Based on a patch by Pradeep Satyanarayana <pradeep@us.ibm.com> and
David Wilder <dwilder@us.ibm.com>, with debugging help from Hoang-Nam
Nguyen <hnguyen@de.ibm.com>.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:47 -07:00
Eli Cohen f89271da32 IPoIB: Copy small received SKBs in connected mode
The connected mode implementation in the IPoIB driver has a large
overhead in the way SKBs are handled in the receive flow.  It usually
allocates an SKB with as big as was used in the currently received SKB
and moves unused fragments from the old SKB to the new one. This
involves a loop on all the remaining fragments and incurs overhead on
the CPU.  This patch, for small SKBs, allocates an SKB just large
enough to contain the received data and copies to it the data from the
received SKB.  The newly allocated SKB is passed to the stack and the
old SKB is reposted.

When running netperf, UDP small messages, without this pach I get:

    UDP UNIDIRECTIONAL SEND TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
    14.4.3.178 (14.4.3.178) port 0 AF_INET
    Socket  Message  Elapsed      Messages
    Size    Size     Time         Okay Errors   Throughput
    bytes   bytes    secs            #      #   10^6bits/sec

    114688     128   10.00     5142034      0     526.31
    114688           10.00     1130489            115.71

With this patch I get both send and receive at ~315 mbps.

The reason that send performance actually slows down is as follows:
When using this patch, the overhead of the CPU for handling RX packets
is dramatically reduced.  As a result, we do not experience RNR NAK
messages from the receiver which cause the connection to be closed and
reopened again; when the patch is not used, the receiver cannot handle
the packets fast enough so there is less time to post new buffers and
hence the mentioned RNR NACKs.  So what happens is that the
application *thinks* it posted a certain number of packets for
transmission but these packets are flushed and do not really get
transmitted.  Since the connection gets opened and closed many times,
each time netperf gets the CPU time that otherwise would have been
given to IPoIB to actually transmit the packets.  This can be verified
when looking at the port counters -- the output of ifconfig and the
oputput of netperf (this is for the case without the patch):

    tx packets
    ==========
    port counter:   1,543,996
    ifconfig:       1,581,426
    netperf:        5,142,034

    rx packets
    ==========
    netperf         1,1304,089

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
2008-07-14 23:48:44 -07:00
Roland Dreier f3781d2e89 RDMA: Remove subversion $Id tags
They don't get updated by git and so they're worse than useless.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-07-14 23:48:44 -07:00
Jack Morgenstein e1d50dce5a IPoIB: Test for NULL broadcast object in ipiob_mcast_join_finish()
We saw a kernel oops in our regression testing when a multicast "join
finish" occurred just after the interface was -- this is
<https://bugs.openfabrics.org/show_bug.cgi?id=1040>.  The test
randomly causes the HCA physical port to go down then up.

The cause of this is that ipoib_mcast_join_finish() processing happen
just after ipoib_mcast_dev_flush() was invoked (in which case the
broadcast pointer is NULL).  This patch tests for and handles the case
where priv->broadcast is NULL.

Cc: <stable@kernel.org>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-05-20 15:41:09 -07:00
Eli Cohen 57ce41d1d1 IB/ipoib: Fix transmit queue stalling forever
Commit f56bcd80 ("IPoIB: Use separate CQ for UD send completions")
introduced a bug where the transmit queue could get stopped and never
woken up.  The problem is that send completions are only polled at the
end of the xmit function, so if the send queue fills up and the xmit
path stops the queue, then there is no way for send completions to
ever get polled, and so the transmit queue stays stopped forever.

Fix this by arming the send CQ just before posting the last send
request that fills the send queue.  Then, when the completion event
handler is called, drain the send CQ.  Since it is possible that not
enough send completions are in the CQ, verify that the the net queue
has been woken up after draining the send CQ, and if not arm a timer
and drain again at the timer function.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-30 20:02:45 -07:00
Eli Cohen b4132efa1a IPoIB: Copy child MTU from parent
When creating a child interface, copy the MTU information from the
parent.  Otherwise when the child's multicast join completes, the MTU
will not be updated since the code does

	dev->mtu = min(priv->mcast_mtu, priv->admin_mtu);

and priv->admin_mtu will be set to 0.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-29 13:46:53 -07:00
Eli Cohen f56bcd8013 IPoIB: Use separate CQ for UD send completions
Use a dedicated CQ for UD send completions. Also, do not arm the UD
send CQ, which reduces the number of interrupts generated.  This patch
farther reduces overhead by not calling poll CQ for every posted send
WR -- it does polls only when there 16 or more outstanding work requests.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-29 13:46:53 -07:00
Shirley Ma bc7b3a36ba IPoIB: Handle 4K IB MTU for UD (datagram) mode
This patch enables IPoIB to use 4K UD messages (when the underlying
device and fabrics support a 4K MTU) by using two scatter buffers when
PAGE_SIZE is less than or equal to thhe HCA IB MTU size.  The first
buffer is for IPoIB header + GRH header, and the second buffer is the
IPoIB payload, which is 4K-4.

Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-23 11:55:45 -07:00
Roland Dreier 9fdd5e5bf6 IPoIB: Handle case when P_Key is deleted and re-added at same index
If a P_Key is deleted and then re-added at the same index, then IPoIB
gets confused because __ipoib_ib_dev_flush() only checks whether the
index is the same without checking whether the P_Key was present, so
the interface is stopped when the P_Key is deleted, but the event when
the P_Key is re-added gets ignored and the interface never gets
restarted.

Also, switch to using ib_find_pkey() instead of ib_find_cached_pkey()
everywhere in IPoIB, since none of the places that look for P_Keys are
in a fast path or in non-sleeping context, and in general we want to
kill off the whole caching infrastructure eventually.  This also fixes
consistency problems caused because some IPoIB queries were cached and
some were uncached during the window where the cache was not updated.

Thanks to Venkata Subramonyam <vsubramo@cisco.com> for debugging this
problem and testing this fix.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:35 -07:00
Eli Cohen 28d52b3cd8 IPoIB: Support modifying IPoIB CQ event moderation
This can be used to tune at run time the parameters controlling the
event (interrupt) generation rate and thus reduce the overhead
incurred by handling interrupts resulting in better throughput.  Since
IPoIB uses a single CQ for both RX and TX, RX is chosen to dictate
configuration for both RX and TX.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:33 -07:00
Eli Cohen 82c24c18af IPoIB: Add basic ethtool support
Just add the infrastructure so we can add functionality later.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:32 -07:00
Eli Cohen 40ca1988e0 IPoIB: Add LSO support
For HCAs that support TCP segmentation offload (IB_DEVICE_UD_TSO), set
NETIF_F_TSO and use HW LSO to offload TCP segmentation.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:27 -07:00
Robert P. J. Day 157de22946 IB: Use shorter list_splice_init() for brevity
Convert list_splice() + INIT_LIST_HEAD() to the equivalent list_splice_init()

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:09:26 -07:00
Eli Cohen 6046136c74 IPoIB: Use checksum offload support if available
For HCAs that support checksum offload (ie that set IB_DEVICE_UD_IP_CSUM
in the device capabilities flags), have IPoIB set NETIF_F_IP_CSUM and
use the HCA to generate and verify IP checksums.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-16 21:01:10 -07:00
Roland Dreier 10313cbb92 IPoIB: Allocate priv->tx_ring with vmalloc()
Commit 7143740d ("IPoIB: Add send gather support") made struct
ipoib_tx_buf significantly larger, since the mapping member changed
from a single u64 to an array with MAX_SKB_FRAGS + 1 entries.  This
means that allocating tx_rings with kzalloc() may fail because there
is not enough contiguous memory for the new, much bigger size.  Fix
this regression by allocating the rings with vmalloc() instead.

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-03-12 07:51:03 -07:00
Roland Dreier 4200406b8f IPoIB/cm: Set tx_wr.num_sge in connected mode post_send()
Commit 7143740d ("IPoIB: Add send gather support") made it possible
for tx_wr.num_sge to be != 1 -- this happens if send gather support is
enabled.  However, the code in the connected mode post_send() function
assumes the old invariant, namely that tx_wr.num_sge is always 1.  Fix
this by explicitly setting tx_wr.num_sge to 1 in the CM post_send().

Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-03-11 18:35:20 -07:00
Or Gerlitz b3e2749bf3 IPoIB: Don't drop multicast sends when they can be queued
When set_multicast_list() is called the multicast task is restarted
and the IPOIB_MCAST_STARTED bit is cleared.  As a result for some
window of time, multicast packets are not transmitted nor queued but
rather dropped by ipoib_mcast_send().  These dropped packets are
painful in two cases:

 - bonding fail-over which both calls set_multicast_list() on the new
   active slave and sends Gratuitous ARP through that slave.

 - IP_DROP_MEMBERSHIP code which both calls set_multicast_list() on the
   device and issues IGMP leave.

In both these cases, depending on the scheduling of the IPoIB
multicast task, the packets would be dropped.  As a result, in the
bonding case, the failover would not be detected by the peers until
their neighbour is renewed the neighbour (which takes a few tens of
seconds).  In the IGMP case, the IP router doesn't get an IGMP leave
and would only learn on that from further probes on the group (also a
delay of at least a few tens of seconds).

Fix this by allowing transmission (or queuing) depending on the
IPOIB_FLAG_OPER_UP flag instead of the IPOIB_MCAST_STARTED flag.

Signed-off-by: Olga Shern <olgas@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-03-11 14:12:03 -07:00
Pradeep Satyanarayana ec229e5e81 IPoIB/cm: Fix ipoib_cm_dev_stop() cleanup when drain times out
Commit efcd9971 ("IPoIB/cm: Factor out ipoib_cm_free_rx_reap_list()")
introduced a bug in ipoib_cm_dev_stop() when the receive drain times
out.  In that case, the function moves all the pending rx stuff into a
private list but then calls ipoib_cm_free_rx_reap_list(), which
handles a different list.

Fix this by moving everything to the rx_reap_list that will actually
get freed up.

This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=906>.

Signed-off-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-19 10:25:11 -08:00
Eli Cohen a9d1884925 IPoIB: Remove unused struct ipoib_cm_tx.ibwc member
struct ipoib_cm_tx.ibwc is unused since commit 1b524963 ("IPoIB/cm:
Use common CQ for CM send completions"), so remove it.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
2008-02-14 10:30:50 -08:00
Jack Morgenstein 167c42655c IPoIB: On P_Key change event, reset state properly
In P_Key event handling, if the old P_Key is no longer available, the
driver must call ipoib_ib_dev_stop() -- just as it does when the P_Key
is still available (see procedure __ipoib_ib_dev_flush()).

When a P_Key becomes available, the driver will perform ipoib_open(),
which assumes that the QP is in RESET, the cm_id has been
destroyed/deleted, etc.  If ipoib_ib_dev_stop() is not called as
described above, then these assumptions will be false, and the attempt
to bring the interface up will fail.

Found by Mellanox QA.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-14 10:15:06 -08:00
Eli Cohen 7143740d26 IPoIB: Add send gather support
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets.  The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.

We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.

Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-08 14:32:37 -08:00
Eli Cohen eb14032f9e IPoIB: Add high DMA feature flag
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't.  Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.

This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.

Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-02-08 13:39:26 -08:00