Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-20
This series contains updates to i40e and i40evf only.
Philippe Reynes updates i40e and i40evf to use the new ethtool API for
{get|set}_link_ksettings.
Jake provides the remaining patches in the series, starting with a fix
for i40e where the firmware expected the port numbers for the offloaded
UDP tunnels in Little Endian format and we were sending them in Big Endian
format which put the wrong port number to be put in the UDP tunnel list.
Changed the driver to use __be32 values instead of arrays for
(src|dst)_ip. Refactored the exit flow of i40e_add_fdir_ethtool() which
removes the dependency on having a non-zero return value. Fixed a memory
leak by running kfree() and returning immediately when we fail to add
flow director filter. Fixed a potential issue where could update the
filter count without actually succeeding in adding a filter, by moving
the ATR exit check to after we have sent the TCP/IPv4 filter to the ring
successfully. Ensures that the fd_tcp_rule count is reset to 0, before
we reprogram the filters so that we do not end up with a stale count
which does not correctly reflect the number of programmed filters. Added
a check whether we have TCP/IPv4 filters before re-enabling ATR after
flushing and replaying FDIR filters. Added counters for each filter
type in preparation for adding code to properly check the mask value.
Fixed potential issues by explicitly checking the flow type at the
start of i40e_add_fdir_ethtool(). To avoid possible memory leaks,
we now unconditionally delete the old filter, even if it is identical to
the new filter and ensures will always update the filters as expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code relied on i40e_match_fdir_input_set to determine when
determining whether to free the old filter. Change this code so that we
simply unconditionally delete the old filter, even if it's identical to
the new filter. This ensures that we don't leak any memory, and that we
always update the filters as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although we will fail the filter later due to checking flow_type which
will have a bogus invalid type, it is possible future refactoring will
remove this hidden failure case. Avoid a possible issue in the future by
explicitly checking the flow type at the start.
Change-Id: Ia98eb26f7b93ccbe38c7141e8f203ef496fc6598
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ATR exit check after we have sent the TCP/IPv4 filter to the ring
successfully. This avoids an issue where we potentially update the
filter count without actually succeeding in adding the filter. Now, we
only increment the fd_tcp_rule after we've succeeded. Additionally, we
will re-enable ATR mode only after deletion of the filter is actually
posted to the FDIR ring.
Change-ID: If5c1dea422081cc5e2de65618b01b4c3bf6bd586
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of setting err=true and checking this to determine when to free
the raw_packet near the end of the function, simply kfree and return
immediately. The resulting code is a bit cleaner and has one less
variable. This also resolves a subtle bug in the ipv4 case which could
fail to add the first filter and then never free the memory, resulting
in a small memory leak.
Change-ID: I7583aac033481dc794b4acaa14445059c8930ff1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the exit flow of the i40e_add_fdir_ethtool function. Move the
input_label to the end of the function, removing the dependency on
having a non-zero return value. Add a comment explaining why it is ok
not to free the fdir data structure, because the structure is now stored
in the fdir_filter_list.
Change-Id: I723342181d59cd0c9f3b31140c37961ba37bb242
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88 ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88 ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There was a typo that I had left in the code comments for the igb and ixgbe
functions that enabled build_skb support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit f9d40f6a99 ("igb: Revert support for build_skb in
igb") and adds a few changes to update it to work with the latest version
of igb. We are now able to revert the removal of this due to the fact
that with the recent changes to the page count and the use of
DMA_ATTR_SKIP_CPU_SYNC we can make the pages writable so we should not be
invalidating the additional data added when we call build_skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
At this point we have 2 to 3 paths that can be taken depending on what Rx
modes are enabled. In order to better support that and improve the
maintainability I am breaking out the common bits from those paths and
making them into their own functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the size of the frame limited we can now write to an offset within the
buffer instead of having to write at the very start of the buffer. The
advantage to this is that it allows us to leave padding room for things
like supporting XDP in the future.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for using 3K buffers in order 1 pages the same way
we were using 2K buffers in 4K pages. We are reserving 1K of room for now
to have space available for future headroom and tailroom when we enable
build_skb support.
One side effect of this patch is that we can end up using a larger buffer
if jumbo frames is enabled. The impact shouldn't be too great, but it
could hurt small packet performance for UDP workloads if jumbo frames is
enabled as the truesize of frames will be larger.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since there are potential drawbacks to the new Rx allocation approach I
thought it best to add a "chicken bit" so that we can turn the feature off
if in the event that a problem is found.
It also provides a means of validating the legacy Rx path in the event that
we are forced to fall back. At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the handling of page addresses so that we always refer to them using
a void pointer, and try to use the consistent name of va indicating we are
working with a virtual address.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We only need to sync the size of the frame that is read to test. We don't
need to sync the entire Rx buffer. This way the testing is more consistent
with how we handle things in the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to support the use of build_skb going forward it will be necessary
to place a maximum limit on the amount of data we can receive when jumbo
frames is not enabled. In order to do this I am adding a new upper limit
for receive based on the size of a 2K buffer minus padding.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case of the Tx rings we need to only clear the Tx buffer_info when
we are resetting the rings. Ideally we do this when we configure the ring
to bring it back up instead of when we are taking it down in order to avoid
dirtying pages we don't need to.
In addition we don't need to clear the Tx descriptor ring since we will
fully repopulate it when we begin transmitting frames and next_to_watch can
be cleared to prevent the ring from being cleaned beyond that point instead
of needing to touch anything in the Tx descriptor ring.
Finally with these changes we can avoid having to reset the skb member of
the Tx buffer_info structure in the cleanup path since the skb will always
be associated with the first buffer which has next_to_watch set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that instead of going through the entire ring on Rx
cleanup we only go through the region that was designated to be cleaned up
and stop when we reach the region where new allocations should start.
In addition we can avoid having to perform a memset on the Rx buffer_info
structures until we are about to start using the ring again. By deferring
this we can avoid dirtying the cache any more than we have to which can
help to improve the time needed to bring the interface down and then back
up again in a reset or suspend/resume cycle.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
In addition I have updated the code so that we only reset the Rx descriptor
length for descriptor zero when resetting a ring instead of having to do a
memset with 0 over the entire ring. By doing this we can save some time on
initialization.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we are already using DMA attributes in igb for Rx there is no reason
why we can't also apply DMA_ATTR_WEAK_ORDERING which is needed on some
platforms to improve performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.
Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our original filter limit of 8 was based on behavior that we saw from
Linux VMs. Now we're running Other Operating Systems under KVM and we
see that they commonly use more MAC filters. Since it seems weird to
require people to enable trusted VFs just to boot their OS, bump the
number of filters allowed by default.
Change-ID: I76b2dcb2ad6017e39231ad3096c3fb6f065eef5e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for DMA_ATTR_SKIP_CPU_SYNC and
DMA_ATTR_WEAK_ORDERING. By enabling both of these for the Rx path we
are able to see performance improvements on architectures that implement
either one due to the fact that page mapping and unmapping only has to
sync what is actually being used instead of the entire buffer. In addition
by enabling the weak ordering attribute enables a performance improvement
for architectures that can associate a memory ordering with a DMA buffer
such as Sparc.
Change-ID: If176824e8231c5b24b8a5d55b339a6026738fc75
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch clarifies the reason for removal of automatically
firmware-generated filter and explicit addition of filter which
accepts frames with any VLAN id.
Change-ID: Iabf180b6d61c4d8a36d3bcf8457c377a6f2aca0e
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the issue that RSS offloading only works on PF0 by
using the direct register writing of the hash keys for the VFs instead
of using the admin queue command to do so.
Change-ID: Ia02cda7dbaa23def342e8786097a2c03db6f580b
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ethtool -e will error out with a X722 interface
as its EEPROM has a scope limit at offset 0x5B9FFF.
This patch fixes the issue by setting the EEPROM length to
the scope limit to avoid NVM read failure beyond that.
Change-ID: I0b7d4dd6c7f2a57cace438af5dffa0f44c229372
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a solution to avoid adding too many queues to num_lan_msix.
A recent refactor of queue pairs accidentally added all remaining
vectors to the num_lan_msix which can have adverse performance issues,
due to enabling more queues than the number of CPU cores.
This patch removes the old calculation, and replaces it with a simple
algorithm.
1) add queue pairs up to num_online_cpus(), but capped at half of total
vectors
2) then add alternative features such as flow directory and similar
3) finally, add the remaining vectors back to queue pairs, but capped
such that the total number of queue pairs does not exceed
num_online_cpus().
Change-ID: I668abf67d5011a1248866daba8885f4ff00cb8d9
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
(KISS is Keep It Simple, Stupid. Or is it?)
The client interface vastly overengineered for what it needs to do.
It was originally designed to support multiple clients on multiple
netdevs, possibly even with multiple drivers. None of this happened,
and now we know that there will only ever be one client for i40e
(i40iw) and one for i40evf (i40iwvf). So, time for some KISS. Since
i40e and i40evf are a Dynasty, we'll simplify this one to match the
VF interface.
First, be a Destroyer and remove all of the lists and locks required
to support multiple clients. Keep one static around to keep track of
one client, and track the client instances for each netdev in the
driver's pf (or adapter) struct. Now it's Almost Human.
Since we already know the client type is iWarp, get rid of any checks
for this. Same for VSI type - it's always going to be the same type,
so it's just a Parasite.
While we're at it, fix up some comments. This makes the function
headers actually match the functions.
These changes reduce code complexity, simplify maintenance,
squash some lurking timing bugs, and allow us to Rock and Roll All
Nite.
Change-ID: I1ea79948ad73b8685272451440a34507f9a9012e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for upcoming RDMA-capable hardware, add a client
interface to the VF driver. This is a slightly-simplified version
of the PF client interface, with the names changed to protect the
innocent.
Due to the nature of the VF<->PF interactions, the client interface
sometimes needs to call back into itself to pass messages. Because
of this, we can't use the coarse-grained locking like the PF's
client interface uses. Instead, we handle all client interactions
in a separate thread so the watchdog can still run and process
virtual channel messages.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some opcodes added & reordered to be in numerical order with the
rest of the opcodes.
This patch adds admin queue structs to support Wake on LAN feature
for X722.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acquire NVM lock before reads on all devices. Previously, locks were
only used for X722 and later. Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.
Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638
Signed-off-by: Aaron Salter <aaron.k.salter@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On architectures that have a cache line size larger than 64 Bytes we start
running into issues where the amount of headroom for the frame starts
shrinking.
The size of skb_shared_info on a system with a 64B L1 cache line size is
320. This increases to 384 with a 128B cache line, and 512 with a 256B
cache line.
In addition the NET_SKB_PAD value increases as well consistent with the
cache line size. As a result when we get to a 256B cache line as seen on
the s390 we end up 768 bytes used by padding and shared info leaving us
with only 1280 bytes to use for data storage. On architectures such as
this we should default to using 3K Rx buffers out of a 8K page instead of
trying to do 1.5K buffers out of a 4K page.
To take all of this into account I have added one small check so that we
compare the max_frame to the amount of actual data we can store. This was
already occurring for igb, but I had overlooked it for ixgbe as it doesn't
have strict limits for 82599 once we enable jumbo frames. By adding this
check we will automatically enable 3K Rx buffers as soon as the maximum
frame size we can handle drops below the standard Ethernet MTU.
I also went through and fixed one small typo that I found where I had left
an IGB in a variable name due to a copy/paste error.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ixgbe_set_rxfh() updates the rss_key copy in the driver
memory, but does not push the new value into the h/w. This commit
add a new helper for the latter operation and call it in
ixgbe_set_rxfh(), so that the h/w rss key value can be really
updated via ethtool.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix typos and add the following to the scripts/spelling.txt:
overwritting||overwriting
Link: http://lkml.kernel.org/r/1481573103-11329-29-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
applys||applies
The "applyes" in drivers/video/fbdev/aty/radeon_monitor.c is a different
pattern but it was fixed in this commit. The "This functions" in the
same line was fixed as well.
Link: http://lkml.kernel.org/r/1481573103-11329-24-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos and add the following to the scripts/spelling.txt:
varible||variable
While we are here, tidy up the comment blocks that fit in a single line
for drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c and
net/sctp/transport.c.
Link: http://lkml.kernel.org/r/1481573103-11329-11-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following message is logged from time to time when using i40e:
NOHZ: local_softirq_pending 08
i40e may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame. The problem is the same as what was
described in commit ec13ee8014 ("virtio_net: invoke softirqs after
__napi_schedule") and this patch applies the same fix to i40e.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix, or rather, avoid a sparse warning caused by the fact that
csum_replace_by_diff expects to receive a __wsum value. Since the
calculation appears to work, simply typecast the passed paylen value to
__wsum to avoid the warning.
This seems pretty fishy since __wsum was obviously annotated as
a separate type on purpose, so this throws the entire calculation into
question. Since it currently appears to behave as expected, the typecast
is probably safe.
Change-ID: I4fdc5cddd589abc16098176e8a61127e761488f4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists an intermittent bug which causes the 'Link Detected'
field reported by the 'ethtool <iface>' command to be 'Yes' when
in fact, there is no link. This patch fixes the problem by
enabling temporary link polling when i40e_get_link_status returns
an error. This causes the driver to remember that an admin queue
command failed and polls, until the function returns with a success.
Change-Id: I64c69b008db4017b8729f3fc27b8f65c8fe2eaa0
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller