Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_platform_ioremap_resource helper which wraps
platform_get_resource() and devm_ioremap_resource() together.
Generated by: scripts/coccinelle/api/devm_platform_ioremap_resource.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PM has been reworked, so eMMC gets now detected on R-Car H3 ES1.0 and
2.0 as well as M3-N without the workaround. Card detect and write
protect also still work. Remove the workaround.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add SD/MMC driver for Actions Semi Owl SoCs. This driver currently
supports standard, high speed, SDR12, SDR25 and SDR50. DDR50 mode is
supported but it is untested. There is no SDIO support for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SD Host controller on Milbeaut consists of two controller parts.
One is core controller F_SDH30, this is similar to sdhci-fujitsu
controller.
Another is bridge controller.
This bridge controller is not compatible with sdhci-fujitsu controller.
This is special for Milbeaut series. This has some functions.
For example, reset control, clock enable/select for SDR50/25/12, set
property of SD physical pins, retuning control, set capabilityies.
This bridge controller requires special procedures at reset or clock
enablement or change for further tuning of clock.
Signed-off-by: Takao Orito <orito.takao@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SDHC 0x7906 requires a hard reset to clear all internal state.
Otherwise it can get into a bad state where the DATA lines are always
read as zeros.
This change requires firmware that can transition the device into
D3Cold for it to work correctly. If the firmware does not support
transitioning to D3Cold then the power state transitions are a no-op.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In sdhci_do_reset we call the reset callback which is typically
sdhci_reset. sdhci_reset can wait for up to 100ms waiting for the
controller to reset. If SDHCI_RESET_ALL was passed as the flag, the
controller will clear the IRQ mask. If during that 100ms the card is
removed there is no notification to the MMC system that the card was
removed. So from the drivers point of view the card is always present.
By making sdhci_reinit compare the present state it can schedule a
rescan if the card was removed while a reset was in progress.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for CAN
interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage scaling
issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem
-----BEGIN PGP SIGNATURE-----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=Ei7j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
CAN interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage
scaling issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: update Cavium ThunderX2 maintainers
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
reset: fix reset_control_ops kerneldoc comment
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
reset: fix reset_control_get_exclusive kerneldoc comment
reset: fix reset_control_lookup kerneldoc comment
reset: fix of_reset_control_get_count kerneldoc comment
reset: fix of_reset_simple_xlate kerneldoc comment
reset: Fix memory leak in reset_control_array_put()
Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole
new staging driver.
The IIO fixes resolve some reported issues, all are tiny.
The staging driver addition is the vboxsf filesystem, which is the
VirtualBox guest shared folder code. Hans has been trying to get
filesystem reviewers to review the code for many months now, and
Christoph finally said to just merge it in staging now as it is
stand-alone and the filesystem people can review it easier over time
that way.
I know it's late for this big of an addition, but it is stand-alone.
The code has been in linux-next for a while, long enough to pick up a
few tiny fixes for it already so people are looking at it.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXcgvVg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylt6gCdG1hmZiOXhmoO1HBBFILqJkrzEVEAn3amZIJJ
n0gz5/FDfQVFGl/PpKCE
=u/mY
-----END PGP SIGNATURE-----
Merge tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes and staging driver from Greg KH:
"Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole
new staging driver.
The IIO fixes resolve some reported issues, all are tiny.
The staging driver addition is the vboxsf filesystem, which is the
VirtualBox guest shared folder code. Hans has been trying to get
filesystem reviewers to review the code for many months now, and
Christoph finally said to just merge it in staging now as it is
stand-alone and the filesystem people can review it easier over time
that way.
I know it's late for this big of an addition, but it is stand-alone.
The code has been in linux-next for a while, long enough to pick up a
few tiny fixes for it already so people are looking at it.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: Fix error return code in vboxsf_fill_super()
staging: vboxsf: fix dereference of pointer dentry before it is null checked
staging: vboxsf: Remove unused including <linux/version.h>
staging: Add VirtualBox guest shared folder (vboxsf) support
iio: adc: stm32-adc: fix stopping dma
iio: imu: inv_mpu6050: fix no data on MPU6050
iio: srf04: fix wrong limitation in distance measuring
iio: imu: adis16480: make sure provided frequency is positive
Here are a number of late-arrival driver fixes for issues reported for
some char/misc drivers for 5.4-rc7
These all come from the different subsystem/driver maintainers as things
that they had reports for and wanted to see fixed.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXcguaA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk9agCdHawCyOWaCfWrUF+66DfI0ql5HhQAoKI0n4yT
7N8GuJ5KsVKmtkkg9Oww
=CZY+
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of late-arrival driver fixes for issues reported for
some char/misc drivers for 5.4-rc7
These all come from the different subsystem/driver maintainers as
things that they had reports for and wanted to see fixed.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
intel_th: pci: Add Jasper Lake PCH support
intel_th: pci: Add Comet Lake PCH support
intel_th: msu: Fix possible memory leak in mode_store()
intel_th: msu: Fix overflow in shift of an unsigned int
intel_th: msu: Fix missing allocation failure check on a kstrndup
intel_th: msu: Fix an uninitialized mutex
intel_th: gth: Fix the window switching sequence
soundwire: slave: fix scanf format
soundwire: intel: fix intel_register_dai PDI offsets and numbers
interconnect: Add locking in icc_set_tag()
interconnect: qcom: Fix icc_onecell_data allocation
soundwire: depend on ACPI || OF
soundwire: depend on ACPI
thunderbolt: Drop unnecessary read when writing LC command in Ice Lake
thunderbolt: Fix lockdep circular locking depedency warning
thunderbolt: Read DP IN adapter first two dwords in one go
- fix a regression from this merge window in the configfs
symlink handling (Honggang Li)
-----BEGIN PGP SIGNATURE-----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=kgn+
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-5.4-2' of git://git.infradead.org/users/hch/configfs
Pull configfs regression fix from Christoph Hellwig:
"Fix a regression from this merge window in the configfs symlink
handling (Honggang Li)"
* tag 'configfs-for-5.4-2' of git://git.infradead.org/users/hch/configfs:
configfs: calculate the depth of parent item
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Make the tsc=reliable/nowatchdog command line parameter work again.
It was broken with the introduction of the early TSC clocksource.
- Prevent the evaluation of exception stacks before they are set up.
This causes a crash in dumpstack because the stack walk termination
gets screwed up.
- Prevent a NULL pointer dereference in the rescource control file
system.
- Avoid bogus warnings about APIC id mismatch related to the LDR
which can happen when the LDR is not in use and therefore not
initialized. Only evaluate that when the APIC is in logical
destination mode"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early
x86/dumpstack/64: Don't evaluate exception stacks before setup
x86/apic/32: Avoid bogus LDR warnings
x86/resctrl: Prevent NULL pointer dereference when reading mondata
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for scheduler regressions:
- Plug a subtle race condition which was introduced with the rework
of the next task selection functionality. The change of task
properties became unprotected which can be observed inconsistently
causing state corruption.
- A trivial compile fix for CONFIG_CGROUPS=n"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix pick_next_task() vs 'change' pattern race
sched/core: Fix compilation error when cgroup not selected
Pull perf tooling fixes from Thomas Gleixner:
- Fix the time sorting algorithm which was broken due to truncation of
big numbers
- Fix the python script generator fail caused by a broken tracepoint
array iterator
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix time sorting
perf tools: Remove unused trace_find_next_event()
perf scripting engines: Iterate on tep event arrays directly
Pull irq fixlet from Thomas Gleixner:
"A trivial fix for a kernel doc regression where an argument change was
not reflected in the documentation"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
Pull stacktrace fix from Thomas Gleixner:
"A small fix for a stacktrace regression.
Saving a stacktrace for a foreign task skipped an extra entry which
makes e.g. the output of /proc/$PID/stack incomplete"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace: Don't skip first entry on noncurrent tasks
config option GENERIC_IO was removed but still selected by lib/kconfig
This patch finish the cleaning.
Fixes: 9de8da4774 ("kconfig: kill off GENERIC_IO option")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=CZxY
-----END PGP SIGNATURE-----
Merge tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few regressions and fixes for stable.
Regressions:
- fix a race leading to metadata space leak after task received a
signal
- un-deprecate 2 ioctls, marked as deprecated by mistake
Fixes:
- fix limit check for number of devices during chunk allocation
- fix a race due to double evaluation of i_size_read inside max()
macro, can cause a crash
- remove wrong device id check in tree-checker"
* tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: un-deprecate ioctls START_SYNC and WAIT_SYNC
btrfs: save i_size to avoid double evaluation of i_size_read in compress_file_range
Btrfs: fix race leading to metadata space leak after task received signal
btrfs: tree-checker: Fix wrong check on max devid
btrfs: Consider system chunk array size for new SYSTEM chunks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl3GikoACgkQ+iyteGJfRsoJrwCeKcV3lXSF4pnmHPK9yjP3bL5Y
leMAnjgQrVHljuShcBCzgNgb1I/Ln/BB
=ziku
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- cpwd: fix build regression
- pm8916_wdt: fix pretimeout registration flow
- meson: Fix the wrong value of left time
- imx_sc_wdt: Pretimeout should follow SCU firmware format
- bd70528: Add MODULE_ALIAS to allow module auto loading
* tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: bd70528: Add MODULE_ALIAS to allow module auto loading
watchdog: imx_sc_wdt: Pretimeout should follow SCU firmware format
watchdog: meson: Fix the wrong value of left time
watchdog: pm8916_wdt: fix pretimeout registration flow
watchdog: cpwd: fix build regression
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
-----BEGIN PGP SIGNATURE-----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=8B/z
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Two NVMe device removal crash fixes, and a compat fixup for for an
ioctl that was introduced in this release (Anton, Charles, Max - via
Keith)
- Missing error path mutex unlock for drbd (Dan)
- cgroup writeback fixup on dead memcg (Tejun)
- blkcg online stats print fix (Tejun)
* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
block: drbd: remove a stray unlock in __drbd_send_protocol()
blkcg: make blkcg_print_stat() print stats only for online blkgs
nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
nvme-rdma: fix a segmentation fault during module unload
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Here's one more fix to keep a reference to the driver's module as long
as there are users of the PWM exposed by the driver.
-----BEGIN PGP SIGNATURE-----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=WelB
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"One more fix to keep a reference to the driver's module as long as
there are users of the PWM exposed by the driver"
* tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: Prevent unloading the driver module while in use
Commit 67692435c4 ("sched: Rework pick_next_task() slow-path")
inadvertly introduced a race because it changed a previously
unexplored dependency between dropping the rq->lock and
sched_class::put_prev_task().
The comments about dropping rq->lock, in for example
newidle_balance(), only mentions the task being current and ->on_cpu
being set. But when we look at the 'change' pattern (in for example
sched_setnuma()):
queued = task_on_rq_queued(p); /* p->on_rq == TASK_ON_RQ_QUEUED */
running = task_current(rq, p); /* rq->curr == p */
if (queued)
dequeue_task(...);
if (running)
put_prev_task(...);
/* change task properties */
if (queued)
enqueue_task(...);
if (running)
set_next_task(...);
It becomes obvious that if we do this after put_prev_task() has
already been called on @p, things go sideways. This is exactly what
the commit in question allows to happen when it does:
prev->sched_class->put_prev_task(rq, prev, rf);
if (!rq->nr_running)
newidle_balance(rq, rf);
The newidle_balance() call will drop rq->lock after we've called
put_prev_task() and that allows the above 'change' pattern to
interleave and mess up the state.
Furthermore, it turns out we lost the RT-pull when we put the last DL
task.
Fix both problems by extracting the balancing from put_prev_task() and
doing a multi-class balance() pass before put_prev_task().
Fixes: 67692435c4 ("sched: Rework pick_next_task() slow-path")
Reported-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Quentin Perret <qperret@google.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
When cgroup is disabled the following compilation error was hit
kernel/sched/core.c: In function ‘uclamp_update_active_tasks’:
kernel/sched/core.c:1081:23: error: storage size of ‘it’ isn’t known
struct css_task_iter it;
^~
kernel/sched/core.c:1084:2: error: implicit declaration of function ‘css_task_iter_start’; did you mean ‘__sg_page_iter_start’? [-Werror=implicit-function-declaration]
css_task_iter_start(css, 0, &it);
^~~~~~~~~~~~~~~~~~~
__sg_page_iter_start
kernel/sched/core.c:1085:14: error: implicit declaration of function ‘css_task_iter_next’; did you mean ‘__sg_page_iter_next’? [-Werror=implicit-function-declaration]
while ((p = css_task_iter_next(&it))) {
^~~~~~~~~~~~~~~~~~
__sg_page_iter_next
kernel/sched/core.c:1091:2: error: implicit declaration of function ‘css_task_iter_end’; did you mean ‘get_task_cred’? [-Werror=implicit-function-declaration]
css_task_iter_end(&it);
^~~~~~~~~~~~~~~~~
get_task_cred
kernel/sched/core.c:1081:23: warning: unused variable ‘it’ [-Wunused-variable]
struct css_task_iter it;
^~
cc1: some warnings being treated as errors
make[2]: *** [kernel/sched/core.o] Error 1
Fix by protetion uclamp_update_active_tasks() with
CONFIG_UCLAMP_TASK_GROUP
Fixes: babbe170e0 ("sched/uclamp: Update CPU's refcount on TG's clamp changes")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Patrick Bellasi <patrick.bellasi@matbug.net>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Ben Segall <bsegall@google.com>
Link: https://lkml.kernel.org/r/20191105112212.596-1-qais.yousef@arm.com
cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead. This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).
Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups. When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.
While c3aab9a0bd ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages. However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.
Skip the immediate switching if the associated memcg is dying.
This is a simplified version of the following two patches:
* https://lore.kernel.org/linux-mm/20190513183053.GA73423@dennisz-mbp/
* http://lkml.kernel.org/r/156355839560.2063.5265687291430814589.stgit@buzz
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: e8a7abf5a5 ("writeback: disassociate inodes from dying bdi_writebacks")
Acked-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
further restrict copy_file_range() to avoid potential data corruption
from Luis and a fix for !CONFIG_CEPH_FSCACHE kernels. Everything but
the fscache fix is marked for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl3FjtQTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHziyjfCACbNiRHpTWfuZ1iHXXCpo0tAixOT6i0
9ZlE8yiF6U6iH7uv/MuIeJ+Qeep9+6wwgJYEJKcF0e+Raiob7womDO+yeDx6RYrC
bqq6OLjJl8VbfeQWvJTmisGTPpvOsOKxxXIKG6vx1zJaJ69yENilFZ0biis14iTu
RRDvtSntc96OhZ3n8IXie2+f9purYeIKhiCZqx9WzYZOk5sb3zGyhqD+Wh5kxkEh
QzwwZ/G5RYvMMhL0o13uMZrjqozGTI9Qm09u7+EikIXFFtt+szEdgFd4pQPhsC1D
VmpdrvV4ml8JnbkENiZ7tlHCcICQJfgMWNcLVgHvD6808CJ0UP5Cq/jP
=34Iz
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Some late-breaking dentry handling fixes from Al and Jeff, a patch to
further restrict copy_file_range() to avoid potential data corruption
from Luis and a fix for !CONFIG_CEPH_FSCACHE kernels.
Everything but the fscache fix is marked for stable"
* tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client:
ceph: return -EINVAL if given fsc mount option on kernel w/o support
ceph: don't allow copy_file_range when stripe_count != 1
ceph: don't try to handle hashed dentries in non-O_CREAT atomic_open
ceph: add missing check in d_revalidate snapdir handling
ceph: fix RCU case handling in ceph_d_revalidate()
ceph: fix use-after-free in __ceph_remove_cap()
The "42f5cda5eaf4" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.
This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.
Fixes: 42f5cda5ea ("vsock/virtio: set SOCK_DONE on peer shutdown")
Cc: Stephen Barber <smbarber@chromium.org>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* we hit a failure path bug related to
ieee80211_txq_setup_flows()
* also use kvmalloc() to make that less likely
* fix a timing value shortly after boot (during
INITIAL_JIFFIES)
-----BEGIN PGP SIGNATURE-----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=jkY+
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three small fixes:
* we hit a failure path bug related to
ieee80211_txq_setup_flows()
* also use kvmalloc() to make that less likely
* fix a timing value shortly after boot (during
INITIAL_JIFFIES)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526 ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix `make nsdeps` for modules composed of multiple source files. Since
$mod_source_files is not in quotes in the call to generate_deps_for_ns(), not
all the source files for a module were being passed to spatch.
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9XXQ
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull modules fix from Jessica Yu:
"Fix `make nsdeps` for modules composed of multiple source files.
Since $mod_source_files was not in quotes in the call to
generate_deps_for_ns(), not all the source files for a module were
being passed to spatch"
* tag 'modules-for-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
scripts/nsdeps: make sure to pass all module source files to spatch
- Fix pte_same() to avoid getting stuck on write fault
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl3FPbsQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNOkjB/9sNekV5x5vtLSXLPXH7TEt2jsKPHKHoc5h
i9bnpZc8na50Sj9V4ugMs4mqa5qOw+m2sJEHXxVr5k/bNJv3gqEpWAlnb4bXgjDj
yukM9FQVBRNMdDFeP3Yjm9VuoWhId0L9OfqCq/N6xi2kN3Xp60Ms7drYQeweBdEa
dBj4x52o/lMo3h5JF0QmWKTD85Nz0f4GxX4gclBMqsg/VAQOMDho86mMsfecwgCA
y9WbJClsH3nBcV8bChx0oSGzM+lJBmP6OnlxKM9tyzTmhJJQw4FDUmHmlaFptMe4
DRqJnVi41tzv7p8As/aE4sY7rnWEKaitn0r7gCfei+ACJG0Ezmas
=3M1Z
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix pte_same() to avoid getting stuck on write fault.
This single arm64 fix is a revert of 747a70e60b ("arm64: Fix
copy-on-write referencing in HugeTLB"), not because that patch was
wrong, but because it was broken by aa57157be6 ("arm64: Ensure
VM_WRITE|VM_SHARED ptes are clean by default") which we merged in
-rc6.
We spotted the issue in Android (AOSP), where one of the JIT threads
gets stuck on a write fault during boot because the faulting pte is
marked as PTE_DIRTY | PTE_WRITE | PTE_RDONLY and the fault handler
decides that there's nothing to do thanks to pte_same() masking out
PTE_RDONLY.
Thanks to John Stultz for reporting this and testing this so quickly,
and to Steve Capper for confirming that the HugeTLB tests continue to
pass"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Do not mask out PTE_RDONLY in pte_same()
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Fixes: daa5abc41c ("pwm: Add support for Broadcom iProc PWM controller")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
These patches all fix various bugs, some of which people have tripped
over and some of which have been caught by automatic tools.
Matthew Wilcox (Oracle) (5):
XArray: Fix xas_next() with a single entry at 0
idr: Fix idr_get_next_ul race with idr_remove
radix tree: Remove radix_tree_iter_find
idr: Fix integer overflow in idr_for_each_entry
idr: Fix idr_alloc_u32 on 32-bit systems
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEejHryeLBw/spnjHrDpNsjXcpgj4FAl3E4tgACgkQDpNsjXcp
gj7YjQf6ArvGGHp3U+w1TRA4KCIrtUdGY4nceDQSYaJ2IVus+fHDQnwMCJb5Rjzw
3aFZKLrrsaWWGKTqqRDKD4zm6I6Mg1239WNCnJ8VQrSRepNQ7WxVXGFn560NDZ5b
u7zYXBm3CtlJpkX9JVbokii4LkjuwXzbuSh6cv+X3APBUQ3JXuGBmT7p2PLp0ol9
lNKUrxZCK+CJ7kJo5W81lCzZc6GY2USqwmuqudGACWMm1K24TRL52PeD8NU6IzKc
Mw9c7Osa0TlwjSaxObaRgLYzIZQoNbkrMTg0xNr8GZjJIn/yJIxqOBb4k3mZWQF1
5KmLfpLotItt25MP8jxgx+1N03jjvw==
=h6eN
-----END PGP SIGNATURE-----
Merge tag 'xarray-5.4' of git://git.infradead.org/users/willy/linux-dax
Pull XArray fixes from Matthew Wilcox:
"These all fix various bugs, some of which people have tripped over and
some of which have been caught by automatic tools"
* tag 'xarray-5.4' of git://git.infradead.org/users/willy/linux-dax:
idr: Fix idr_alloc_u32 on 32-bit systems
idr: Fix integer overflow in idr_for_each_entry
radix tree: Remove radix_tree_iter_find
idr: Fix idr_get_next_ul race with idr_remove
XArray: Fix xas_next() with a single entry at 0