If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maximum delay for waking up card is 50 ms. Because of typo in
counter, this delay goes to 500ms. This patch fixes the bug.
Cc: <stable@vger.kernel.org> # 3.2+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.
On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.
With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k commit 2ef167557c
(ath9k: fix signal strength reporting issues) fixed an issue where the
reported per-frame signal strength reported to mac80211 was being
overwritten with an internal average. The same issue is also present
in ath9k_htc.
In addition to preventing the driver from overwriting the value, this
commit also ensures that the internal average (which is used for ANI)
only tracks beacons of the AP that we're connected to.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This USB ethernet adapter was purchased in anodyne packaging
from the computer store adjacent to linux.conf.au 2013 in
Canberra (Australia). A web search shows other recent
purchasers in Lancaster (UK) and Seattle (USA). Just like an
emergent virus, our age of e-commerce and airmail allows
underdocumented hardware to spread around the world instantly
using the vector of ridiculously low prices.
Paige Thompson, infected via eBay, discovered that the HG20F9
is a copy of the Asix 88772B; many viruses copy the RNA of
other viruses. See Paige's work at
<https://github.com/paigeadele/HG20F9>.
This patch uses her discovery to update the restructured Asix
driver in the current kernel.
Just as some viruses inhabit seemingly-healthy cells, the
HG20F9 uses the Vendor ID 0x066b assigned to Linksys Inc.
For the present there is no clash of Product ID 0x20f9.
Signed-off-by: Glen Turner <gdt@gdt.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tag all Huawei NCM devices as WWAN modems, as we don't know of any which
are not. This is necessary for userspace clients to know that the device
requires further setup on e.g. an AT-capable serial ports before
connectivity is available.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 86564c3f "bnx2x: Remove many sparse warnings" UDP
csum offload is broken for 57710/57711. Fix return value.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
CC: Ariel Elior <ariele@broadcom.com>
CC: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PIC was supposed to be a small signature appended to the
PhyDB data, but the signature isn't really static and thus
attempting to check it just causes the warnings spuriously
so remove them.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wakeup packet in the status response is padded out
to a multiple of 4 bytes by the firmware for transfer
to the host, take that into account when checking the
length of the command.
Also, the reported wakeup packet includes the FCS but
the userspace API doesn't, so remove that. If it is a
data packet it is reported as an 802.3 packet but I
forgot to take into account and remove the encryption
head/tail, fix all of that as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KcDx
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"All trivial, thanks to the stuff which didn't quite make it time"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_console: Initialize guest_connected=true for rproc_serial
virtio: use module_virtio_driver.
virtio: Add module driver macro for virtio drivers.
virtio_console: Use virtio device index to generate port name
virtio: make pci_device_id const
virtio: make config_ops const
virtio-mmio: fix wrong comment about register offset
virtio_console: Let unconnected rproc device receive data.
in bond_enslave(), check slave_cnt before actually using slave address.
introduced by:
commit 409cc1f8a4 (bond: have random dev address by default instead of zeroes)
Reported-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cpsw_add_default_vlan() look at the actual number of slaves for its
iteration, so boards with less than 2 slaves don't ooops at boot.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Some fixes that should go into 3.9:
1. Fix packet corruption when using non-coherent RX DMA buffers.
2. Fix occasional watchdog misfiring when changing MTU or ring size.
These are longstanding bugs and should be fixed in stable as well, but
I'd like to review other recent fixes first and send a separate request
for stable inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When stations are removed while packets are in the queue,
we drain the queues first, and then remove the stations.
If this happens in AP mode while the interface is removed
the MAC context might be removed from the firmware before
we removed the station(s), resulting in a SYSASSERT 3421.
This is because we remove the MAC context from the FW in
stop_ap(), but only flush the station drain work later in
remove_interface().
Refactor the code a bit to have a common MAC context
removal preparation first to solve this.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FH hardware will always write back to the scratch field
in commands, even host commands not just TX commands, which
can overwrite parts of the command. This is problematic if
the command is re-used (with IWL_HCMD_DFL_NOCOPY) and can
cause calibration issues.
Address this problem by always putting at least the first
16 bytes into the buffer we also use for the command header
and therefore make the DMA engine write back into this.
For commands that are smaller than 16 bytes also always map
enough memory for the DMA engine to write back to.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle, Wei Yongjun
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RAQw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband update from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
Wei Yongjun"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
IB/mlx4: Advertise MW support
IB/mlx4: Support memory window binding
mlx4: Implement memory windows allocation and deallocation
mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
mlx4_core: Disable memory windows for virtual functions
IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
IB/srp: Fail I/O requests if the transport is offline
IB/srp: Avoid endless SCSI error handling loop
IB/srp: Avoid sending a task management function needlessly
IB/srp: Track connection state properly
IB/mlx4: Remove redundant NULL check before kfree
IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
IB/iser: Enable iser when FMRs are not supported
IB/iser: Avoid error prints on EAGAIN registration failures
IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
IB/uverbs: Implement memory windows support in uverbs
IB/core: Add "type 2" memory windows support
mlx4_core: Propagate MR deregistration failures to caller
mlx4_core: Rename MPT-related functions to have mpt_ prefix
...
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
The device is ready if all the following are true:
(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up
(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b). We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation. We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed. We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent. (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The name of FEATURE_AUTOSUSPEND is very misleading and the actual
meaning is remote wakeup, but a device incapable of remote wakeup
still can support USB autosuspend under some situations, so rename
it to avoid misunderstanding.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b2d4b150(smsc95xx: enable dynamic autosuspend) implements
autosuspend, but breaks current runtime suspend, such as:
when the interface becomes down, the usb device can't be put into
runtime suspend any more.
This patch fixes the broken runtime suspend.
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The three below functions:
smsc95xx_enter_suspend0()
smsc95xx_enter_suspend1()
smsc95xx_enter_suspend2()
return > 0 in case of success, so they will cause smsc95xx_suspend()
to return > 0 and cause suspend failure.
The bug is introduced in commit 3b9f7d(smsc95xx: fix error handling
in suspend failure case).
Cc: <stable@vger.kernel.org> [3.8]
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using the same variable for iterating two nested loops.
Reported-by: Tijs Van Buggenhout <tvb@able.be>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unload, b43 produces a lockdep warning that can be summarized in the
following way:
======================================================
[ INFO: possible circular locking dependency detected ]
3.8.0-wl+ #117 Not tainted
-------------------------------------------------------
modprobe/5557 is trying to acquire lock:
((&wl->firmware_load)){+.+.+.}, at: [<ffffffff81062160>] flush_work+0x0/0x2a0
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff813bd7d2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
[ INFO: possible circular locking dependency detected ]
======================================================
The full output is available at http://lkml.indiana.edu/hypermail/linux/kernel/1302.3/00060.html.
To summarize, commit 6b6fa58 added a 'cancel_work_sync(&wl->firmware_load)'
call in the wrong place.
The fix is to move the cancel_work_sync() call to b43_bcma_remove() and
b43_ssb_remove(). Thanks to Johannes Berg and Michael Buesch for help in
diagnosing the log output.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>
tunnel_ip_select_ident() is more efficient when generating ip-header
id given inner packet is of ipv4 type.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement MW allocation and deallocation in mlx4_core and mlx4_ib.
Pass down the enable bind flag when registering memory regions.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add memory windows-related code to INIT_HCA and QUERY_HCA.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Do not enable memory windows allocation for virtual functions.
In addition, add a few safety checks, such as:
* Verifying the PD of a new MPT matches the VF.
* Making sure binding memory window isn't enabled for FMRs, and
that new memory windows are not FMR themselves.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix missing () & { }
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that vmxnet3's get_ringparam function was returning the summation of all
ring buffers on a NIC, rather than just the size of any one ring. This causes
problems when a vmxnet3 instance has multiple queues, as ethtool, when setting
ring parameters, first gets the current ring parameters to set the existing
values in the set_ringparm commannd. The result is, that unless both rx and tx
ring sizes are set in a single operation, which ever ring is not set will
silently have its ring count multiplied by the number of queues on the NIC until
it reaches a driver defined maxiumum value.
Fix it by not multiplying the rx and tx ring sizes by the number of queues in
the system, like every other driver. Tested by myself successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse warned about several functions that were unnecessarily global.
After making them static, discovered that several functions were actually never used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eilon Greenstein <eilong@broadcomo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ee873fda3b ("gianfar: Pack struct
gfar_priv_grp into three cachelines") moved the irq number and names
off into a separate struct and created accessors for them. However
it was never tested with NET_POLL enabled, and so some conversions
that were simply overlooked went undetected until now.
Make the netpoll ones also use the gfar_irq() accessors.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff907027b: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en driver allocates the number of objects for the CPU affinity
reverse-map based on the number of rx rings of the device. However,
mlx4_assign_eq() calls irq_cpu_rmap_add() as many times as IRQ's are
assigned to EQ's, which can be as large as mlx4_dev->caps.comp_pool. If
caps.comp_pool is larger than rx_ring_num we will eventually hit the
BUG_ON() in cpu_rmap_add().
Fix this problem by allocating space for the maximum number of CPU
affinity reverse-map objects we might want to add.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory to hold the network device tx_cq is not being allocated with
the correct size in mlx4_en_init_netdev(). It should use MAX_TX_RINGS
instead of MAX_RX_RINGS. This can cause problems if the number of tx
rings being used is greater than MAX_RX_RINGS.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7f7d6c282 (net: fec: Ensure that initialization is done prior to
request_irq()) placed fec_ptp_init() into a point that ptp clock was not
available, which causes a division by zero in fec_ptp_start_cyclecounter():
[ 17.895723] Division by zero in kernel.
[ 17.899571] Backtrace:
[ 17.902094] [<80012564>] (dump_backtrace+0x0/0x10c) from [<8056deec>]
(dump_stack+0x18/0x1c)
[ 17.910539] r6:bfba8500 r5:8075c950 r4:bfba8000 r3:bfbd0000
[ 17.916284] [<8056ded4>] (dump_stack+0x0/0x1c) from [<80012688>]
(__div0+0x18/0x20)
[ 17.923968] [<80012670>] (__div0+0x0/0x20) from [<802829c4>] (Ldiv0+0x8/0x10)
[ 17.931140] [<80398534>] (fec_ptp_start_cyclecounter+0x0/0x110) from
[<80394f64>] (fec_restart+0x6c8/0x754)
[ 17.940898] [<8039489c>] (fec_restart+0x0/0x754) from [<803969a0>]
(fec_enet_adjust_link+0xdc/0x108)
[ 17.950046] [<803968c4>] (fec_enet_adjust_link+0x0/0x108) from [<80390bc4>]
(phy_state_machine+0x178/0x534)
...
Fix this by rearraging the code so that fec_ptp_init() is called only after
the clocks have been properly acquired.
Tested on both mx53 and mx6 platforms.
Reported-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function brcmf_notify_vif_event()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unload sequence for mwifiex PCIE driver is as follows:
1. Invoking cleanup module from kernel results into
pci_unregister_driver
2. Kernel invokes PCIE remove() handler which disconnects all
interfaces.
3. One step during disconnect is to clean PCIE TX rings.
During this we read txbd_rdptr from FW.
While loading driver next time, we see pci_enable_device()
results into system freeze. This may have happened because we
accessed PCI device after unregistering from bus driver.
Removing this ioread() operation resolves this bug.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the system suspends with mwifiex wifi powered on, and is then woken
by an ICMP ping packet, the ping response is discarded by the kernel
because the kernel incorrectly thinks there is no carrier.
I can't see any valid reason to want to report loss of carrier here,
so remove the offending code.
Fixes http://dev.laptop.org/ticket/12554
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
include/linux/ssb/ssb_driver_gige.h
Also resolves a logical merge conflict in drivers/net/ethernet/broadcom/-
bgmac.c due to change of an API.
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Pull trivial tree from Jiri Kosina:
"Assorted tiny fixes queued in trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (22 commits)
DocBook: update EXPORT_SYMBOL entry to point at export.h
Documentation: update top level 00-INDEX file with new additions
ARM: at91/ide: remove unsused at91-ide Kconfig entry
percpu_counter.h: comment code for better readability
x86, efi: fix comment typo in head_32.S
IB: cxgb3: delay freeing mem untill entirely done with it
net: mvneta: remove unneeded version.h include
time: x86: report_lost_ticks doesn't exist any more
pcmcia: avoid static analysis complaint about use-after-free
fs/jfs: Fix typo in comment : 'how may' -> 'how many'
of: add missing documentation for of_platform_populate()
btrfs: remove unnecessary cur_trans set before goto loop in join_transaction
sound: soc: Fix typo in sound/codecs
treewide: Fix typo in various drivers
btrfs: fix comment typos
Update ibmvscsi module name in Kconfig.
powerpc: fix typo (utilties -> utilities)
of: fix spelling mistake in comment
h8300: Fix home page URL in h8300/README
xtensa: Fix home page URL in Kconfig
...
Merge misc patches from Andrew Morton:
- Florian has vanished so I appear to have become fbdev maintainer
again :(
- Joel and Mark are distracted to welcome to the new OCFS2 maintainer
- The backlight queue
- Small core kernel changes
- lib/ updates
- The rtc queue
- Various random bits
* akpm: (164 commits)
rtc: rtc-davinci: use devm_*() functions
rtc: rtc-max8997: use devm_request_threaded_irq()
rtc: rtc-max8907: use devm_request_threaded_irq()
rtc: rtc-da9052: use devm_request_threaded_irq()
rtc: rtc-wm831x: use devm_request_threaded_irq()
rtc: rtc-tps80031: use devm_request_threaded_irq()
rtc: rtc-lp8788: use devm_request_threaded_irq()
rtc: rtc-coh901331: use devm_clk_get()
rtc: rtc-vt8500: use devm_*() functions
rtc: rtc-tps6586x: use devm_request_threaded_irq()
rtc: rtc-imxdi: use devm_clk_get()
rtc: rtc-cmos: use dev_warn()/dev_dbg() instead of printk()/pr_debug()
rtc: rtc-pcf8583: use dev_warn() instead of printk()
rtc: rtc-sun4v: use pr_warn() instead of printk()
rtc: rtc-vr41xx: use dev_info() instead of printk()
rtc: rtc-rs5c313: use pr_err() instead of printk()
rtc: rtc-at91rm9200: use dev_dbg()/dev_err() instead of printk()/pr_debug()
rtc: rtc-rs5c372: use dev_dbg()/dev_warn() instead of printk()/pr_debug()
rtc: rtc-ds2404: use dev_err() instead of printk()
rtc: rtc-efi: use dev_err()/dev_warn()/pr_err() instead of printk()
...
After I came across a help text for SUNGEM mentioning a broken sun.com
URL, I felt like fixing those up, as they are now pointing to oracle.com
URLs.
Signed-off-by: Christian Kujau <lists@nerdbynature.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converting more ARM platforms to multiplatform support. This time, OMAP
gets converted, which is a major step since this is by far the largest
platform in terms of code size. The same thing happens to the vt8500
platform.
Conflicts include:
* Two mach/uncompress.h files are removed, the changes made to them
elsewhere can be discarded now.
* Moving the OMAP4 irq_match array has context clashes with turning
omap4_sar_ram_init into an omap_early_initcall()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nl4h
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform support from Arnd Bergmann:
"Converting more ARM platforms to multiplatform support. This time,
OMAP gets converted, which is a major step since this is by far the
largest platform in terms of code size. The same thing happens to the
vt8500 platform."
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
ARM: OMAP2+: Make sure files with omap initcalls include soc.h
ARM: OMAP2+: Include soc.h to drm.c to fix compiling
ARM: OMAP2+: Fix warning for hwspinlock omap_postcore_initcall
ARM: multi_v7_defconfig: add ARCH_ZYNQ
ARM: multi_v7_defconfig: remove unnecessary CONFIG_GPIOLIB
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
ARM: OMAP2+: Remove now obsolete uncompress.h and debug-macro.S
ARM: OMAP2+: Add minimal support for booting vexpress
ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support
ARM: OMAP2+: Disable code that currently does not work with multiplaform
ARM: OMAP2+: Add multiplatform debug_ll support
ARM: OMAP: Fix dmaengine init for multiplatform
ARM: OMAP: Fix i2c cmdline initcall for multiplatform
ARM: OMAP2+: Use omap initcalls
ARM: OMAP2+: Limit omap initcalls to omap only on multiplatform kernels
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use correct function to clear loopback mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZYQACgkQMUfUDdst+ylJDgCg0B0nMevUUdM4hLvxunbbiyXM
HUEAoIOedqriNNPvX4Bwy0hjeOEaWx0g
=vi6x
-----END PGP SIGNATURE-----
Merge tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial patches from Greg Kroah-Hartman:
"Here's the big tty/serial driver patches for 3.9-rc1.
More tty port rework and fixes from Jiri here, as well as lots of
individual serial driver updates and fixes.
All of these have been in the linux-next tree for a while."
* tag 'tty-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: mxser: improve error handling in mxser_probe() and mxser_module_init()
serial: imx: fix uninitialized variable warning
serial: tegra: assume CONFIG_OF
TTY: do not update atime/mtime on read/write
lguest: select CONFIG_TTY to build properly.
ARM defconfigs: add missing inclusions of linux/platform_device.h
fb/exynos: include platform_device.h
ARM: sa1100/assabet: include platform_device.h directly
serial: imx: Fix recursive locking bug
pps: Fix build breakage from decoupling pps from tty
tty: Remove ancient hardpps()
pps: Additional cleanups in uart_handle_dcd_change
pps: Move timestamp read into PPS code proper
pps: Don't crash the machine when exiting will do
pps: Fix a use-after free bug when unregistering a source.
pps: Use pps_lookup_dev to reduce ldisc coupling
pps: Add pps_lookup_dev() function
tty: serial: uartlite: Support uartlite on big and little endian systems
tty: serial: uartlite: Fix sparse and checkpatch warnings
serial/arc-uart: Miscll DT related updates (Grant's review comments)
...
Fix up trivial conflicts, mostly just due to the TTY config option
clashing with the EXPERIMENTAL removal.
Currently request_irq() is called prior to fec_enet_init() and fec_ptp_init(),
which causes the following crash on a mx53qsb:
Unable to handle kernel NULL pointer dereference at virtual address 00000002
pgd = 80004000
[00000002] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 Not tainted (3.8.0-rc7-next-20130215+ #346)
PC is at fec_enet_interrupt+0xd0/0x348
LR is at fec_enet_interrupt+0xb8/0x348
pc : [<80372b7c>] lr : [<80372b64>] psr: 60000193
sp : df855c20 ip : df855c20 fp : df855c74
r10: 00000516 r9 : 1c000000 r8 : 00000000
r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : df9b7800
r3 : df9b7df4 r2 : 00000000 r1 : 00000000 r0 : df9b7d34
Ensure that such initialization functions are called prior to requesting the
interrupts, so that all necessary the data structures are in place when the
irqs occur.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
MR deregistration fails when memory windows are bound to the MR.
Handle such failures by propagating them to the caller ULP.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MPT - Memory Protection Table - is used by both memory windows and
memory regions. Hence, all MPT references are relevant for both types
of memory objects. Rename the relevant functions to start with mpt_
instead of the current mr_ prefix.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Zlkx
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree changes from Grant Likely:
"All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (23 commits)
Revert "of: use platform_device_add"
kbuild: limit dtc+cpp include path
gpio: Make of_count_named_gpios() use new of_count_phandle_with_args()
of: Create function for counting number of phandles in a property
of/base: Clean up exit paths for of_parse_phandle_with_args()
of/selftest: Use selftest() macro throughout
of/selftest: Fix GPIOs selftest to cover the 7th case
of: fix recursive locking in of_get_next_available_child()
documentation/devicetree: Fix a typo in exynos-dw-mshc.txt
OF: convert devtree lock from rw_lock to raw spinlock
of/exynos_g2d: Add Bindings for exynos G2D driver
kbuild: create a rule to run the pre-processor on *.dts files
input: Extend matrix-keypad device tree binding
devicetree: Move NS2 LEDs binding into LEDs directory
of: use platform_device_add
powerpc/5200: Fix size to request_mem_region() call
documentation/devicetree: Fix typos
of: add 'const' to of_node_full_name parameter
of: Output devicetree alias names in uevent
DT: add vendor prefixes for Renesas and Toshiba
...
Pull workqueue [delayed_]work_pending() cleanups from Tejun Heo:
"This is part of on-going cleanups to remove / minimize usages of
workqueue interfaces which are deprecated and/or misleading.
This round drops a number of usages of [delayed_]work_pending(), which
are dangerous as they lack any form of synchronization and thus often
lead to buggy / unnecessary code. There are a couple legitimate use
cases in kernel. Hopefully, they can be converted and
[delayed_]work_pending() can be removed completely. Even if not,
removing most of misuses should make it more difficult to find
examples of misuses and thus slow down growth of them.
These changes are independent from other workqueue changes."
* 'for-3.9-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
wimax/i2400m: fix i2400m->wake_tx_skb handling
kprobes: fix wait_for_kprobe_optimizer()
ipw2x00: simplify scan_event handling
video/exynos: don't use [delayed_]work_pending()
tty/max3100: don't use [delayed_]work_pending()
x86/mce: don't use [delayed_]work_pending()
rfkill: don't use [delayed_]work_pending()
wl1251: don't use [delayed_]work_pending()
thinkpad_acpi: don't use [delayed_]work_pending()
mwifiex: don't use [delayed_]work_pending()
sja1000: don't use [delayed_]work_pending()
<<
Please pull mpc5xxx patches for v3.9. The bestcomm driver is
moved to drivers/dma (so it will be usable for ColdFire).
mpc5121 now provides common dtsi file and existing mpc5121 device
trees use it. There are some minor clock init and sparse fixes
and updates for various 5200 device tree files from Grant. Some
fixes for bugs in the mpc5121 DIU driver are also included here
(Andrew Morton suggested to push them via my mpc5xxx tree).
>>
If a qdisc is installed on a ppp device, its possible to get
a lockdep splat under stress, because nested dev_queue_xmit() can
lock busylock a second time (on a different device, so its a false
positive)
Avoid this problem using a distinct lock_class_key for ppp
devices.
Reported-by: Yanko Kaneti <yaneti@declera.com>
Tested-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the previous commit : f1f220ea1dda078, the BUSY state of buffer is wrongly
deleted. this patch just restore it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d37204566a.
This change is incorrect, as per Jan Beulich:
====================
But this is wrong from all we can tell, we discussed this before
(Wei pointed to the discussion in an earlier reply). The core of
it is that the put here parallels the one in netbk_tx_err(), and
the one in xenvif_carrier_off() matches the get from
xenvif_connect() (which normally would be done on the path
coming through xenvif_disconnect()).
====================
And a previous discussion of this issue is at:
http://marc.info/?l=xen-devel&m=136084174026977&w=2
Signed-off-by: David S. Miller <davem@davemloft.net>
It advertises a standard CDC-ETHER interface, which actually should be
driven by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sets the sysfs device_type to 'bond' for udev. This allows udev rules to
be created for bond devices. This is similar to how other network
devices set their device_type.
Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following inconsistencies in bond_release_all:
- IFF_BONDING flag is not stripped from slaves
- MTU is not restored
- no netdev notifiers are sent
Instead of trying to keep bond_release and bond_release_all in sync
I think we can re-use bond_release as the environment for calling it
is correct (RTNL is held). I have been running tests for the past
week and they came out successful. The only way for bond_release to fail
is for the slave to be attached in a different bond or to not be a slave
but that cannot happen as RTNL is held and no slave manipulations can be
achieved.
V2: As suggested bond_release is renamed to __bond_release_one with a
new parameter "all" introduced so to avoid calling unnecessary code while
destroying a bond, and a wrapper for it called bond_release is created
because of ndo_del_link. bond_release_all() is removed.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch b44 always allocates the 2 bytes needed for aligned
access on every platform, now it uses netdev_alloc_skb_ip_align().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netbk_fatal_tx_err() calls xenvif_carrier_off(), which does
a xenvif_put(). As callers of netbk_fatal_tx_err should only
have one reference to the vif at this time, then the xenvif_put
in netbk_fatal_tx_err is one too many.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether the phy-reset GPIO is valid, prior to requesting it.
In the case a board does not provide a phy-reset GPIO, just returns immediately.
With such gpio validation in place, it is also safe to change from pr_debug to
dev_err in the case the gpio request fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3ad machine state spinlock can be used before it is inititialized
while doing bond_enslave() (and the port is being initialized) since
port->slave is set before the lock is prepared, thus causing soft
lock-ups and a multitude of other nasty bugs.
[ Rename __initialize_port_locks() variable name to 'slave' -DaveM ]
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port->slave can be NULL since it's being initialized in bond_enslave
thus dereferencing a NULL pointer in bond_3ad_update_lacp_rate()
Also fix a minor bug, which could cause a port not to have
AD_STATE_LACP_TIMEOUT since there's no sync between
bond_3ad_update_lacp_rate() and bond_3ad_bind_slave(), by changing
the read_lock to a write_lock_bh in bond_3ad_update_lacp_rate().
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bastian Bittorf <bittorf@bluebottle.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the MAC address of a VM, from the adapter's embedded switch,
after the VM had been migrated out of this adapter/server.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set gso_size to MSS obtained from adapter to avoid incorrect estimation
of receive MSS, which would lead to delayed ACKs in some traffic patterns
Example:
Send two or three packets and wait for ack and only then send
remaining packets.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Cleanly seperate 83xx Legacy interrupt handling code from 82xx
o Update 83xx Legacy interrupt handling code to match with the spec
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Config interrupt is not needed for mailbox interrupts.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added detailed error messages for FW CDRP command failure
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory allocation using, kmalloc() fails, report appropriate error value.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an instance of DMA buffer on stack(being passed to
usb_control_msg) for the wireless USB version of the Agere Orinoco card driver.
It also fixes the missing audit for the return value of firmware download
routine. Found using smatch.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
struct {
u8 data[254];
struct usb_ctrlrequest dr;
};
Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.
Patch changes setup packet to be allocated separately.
[v2]:
- Use WARN_ON_ONCE instead of WARN_ON
Cc: <stable@vger.kernel.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA mode, collect VHT realated IEs from the Beacons or Probe
Responses and append similar VHT related IEs to association
requests.
For AP mode, get VHT related capability information and share it
with cfg80211 at the time of wiphy register. This information is
further used by cfg80211 and hostapd to start an AP with 802.11AC
support.
Currently only 8897 supports 802.11AC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They all can make one line.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading driver, we free all pending TX packets by flushing
TX ring. There is unhandled case for PCIE8897 while checking for
ring empty condition.
This patch adds the handling by calling mwifiex_pcie_txbd_empty().
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
This probably is the last big pull request for wireless bits
for 3.9. Of course, I'm sure there will be a few stragglers here
and there...surely a few bug fixes as well... :-) (In fact, I see
that Johannes has already queued-up a few more for me while I was
preparing this...)
Included are a number of pulls...
For mac80211-next, Johannes says:
"The biggest change I have is undoubtedly Marco's mesh powersave
implementation. Beyond that, I have a patch from Emmanuel to modify the
DTIM period API in mac80211, scan improvements and a removal of some
previous workaround code from Stanislaw, dynamic short slot time from
Thomas and 64-bit station byte counters from Vladimir. I also made a
number of changes myself, some related to WoWLAN, some auth/deauth
improvements and most of them BSS list cleanups."
"This time, I have relatively large number of fixes in various areas of
the code (a memory leak in regulatory, an RX race in mac80211, the new
radar checking caused a P2P device problem, some mesh issues with
stations, an older bug in tracing and for kernel-doc) as well as a
number of small new features. The biggest (in the diffstat) is my work
on hidden SSID tracking."
"Please pull to get
* radar detection work from Simon
* mesh improvements from Thomas
* a connection monitoring/powersave fix from Wojciech
* TDLS-related station management work from Jouni
* VLAN crypto fixes from Michael Braun
* CCK support in minstrel_ht from Felix
* an SMPS (not SMSP, oops) related improvement in mac80211 (Emmanuel)
* some WoWLAN work from Amitkumar Karwar: pattern match offset and a
documentation fix
* some WoWLAN work from myself (TCP connection wakeup feature API)
* and a lot of VHT (and some HT) work (also from myself)
And a number of more random cleanups/fixes. I merged mac80211/master to
avoid a merge problem there."
And regarding iwlwifi-next, Johannes says:
"We continue work on our new driver, but I also have a WoWLAN and AP mode
improvement for the previous driver and a change to use threaded
interrupts to prepare us for working with non-PCIe devices."
Regarding wl12xx, Luca says:
"A few more patches intended for 3.9. Mostly some clean-ups I've been
doing to make it easier to support device-tree. Also including one bug
fix for wl12xx where the rates we advertise were wrong and an update in
the wlconf structure to support newer firmwares."
For the nfc-next bits, Samuel says:
"This is the second NFC pull request for 3.9.
We have:
- A few pn533 fixes on top of Waldemar refactorization of the driver, one of
them fixes target mode.
- A new driver for Inside Secure microread chipset. It supports two
physical layers: i2c and MEI. The MEI one depends on a patchset that's
been sent to Greg Kroah-Hartman for inclusion into the 3.9 kernel [1]. The
dependency is a KConfig one which means this code is not buildable as long
as the MEI API is not usptream."
"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
For the ath6kl bits, Kalle says:
"There's not anything special here, most of the patches are just code
cleanup. The only functional changes are using the beacon interval from user
space and fixing a crash which happens when inserting and removing the
module in a loop."
Also, I pulled the wireless tree in order to resolve some pending
merge issues. On top of that, there is a bunch of work on brcmfmac
that leads up to P2P support. Also, mwifiex, rtlwifi, and a variety
of other drivers see some basic cleanups and minor enhancements.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPDMA interrupts are not properly acknowledged which leads to interrupt
storm, only cpdma interrupt 0 is acknowledged in Davinci CPDMA driver.
Changed cpdma_ctlr_eoi api to acknowledge 1 and 2 interrupts which are
used for rx and tx respectively.
Reported-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I removed a bit too much info last time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Theoretically, the card may not enter CTKILL:
In case the timer that iwl_prepare_ct_kill_task is setting,
will expire before tt->state revert to its previous state.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time event data structures are required also for P2P Device
interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW can differentiate between scans, according to the interface
type on which the scan was issues. Supply the interfaces type
information to the FW.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Occasionally, we would run into this warning:
iwlwifi 0000:02:00.0: U iwl_mvm_protect_session extend 0x2601: only 200 ms left
iwlwifi 0000:02:00.0: U iwl_mvm_remove_time_event Removing TE 0x2601
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0925, 60 bytes at 37[5]:9
iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Attempting to send sync command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Setting HCMD_ACTIVE for command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0926, 60 bytes at 38[6]:9
iwlwifi 0000:02:00.0: U iwl_mvm_time_event_response TIME_EVENT_CMD response - UID = 0x2601
iwlwifi 0000:02:00.0: I iwl_pcie_hcmd_complete Clearing HCMD_ACTIVE for command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: U iwl_mvm_rx_time_event_notif Time event notification - UID = 0x2701 action 1
wlan0: associate with 00:0a:b8:55:a8:30 (try 2/3)
------------[ cut here ]------------
WARNING: at drivers/net/wireless/iwlwifi/mvm/time-event.c:269 iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]()
Modules linked in: [...]
Call Trace:
[<c1046e42>] warn_slowpath_common+0x72/0xa0
[<c1046e92>] warn_slowpath_null+0x22/0x30
[<f8cad913>] iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]
[<f8cadead>] iwl_mvm_protect_session+0xcd/0x1c0 [iwlmvm]
[<f8ca2087>] iwl_mvm_mac_mgd_prepare_tx+0x67/0xa0 [iwlmvm]
[<f882a130>] ieee80211_sta_work+0x8f0/0x1070 [mac80211]
The reason is a problem with asynchronous vs. synchronous
commands, what happens here is the following:
* TE 0x2601 is removed, the TIME_EVENT_CMD for that is async
* a new TE (will be 0x2701) is created, the TIME_EVENT_CMD
for that is sync and also uses a notification wait for the
response (to avoid another race condition)
* the response for the TE 0x2601 removal comes from the
firmware, and is handled by the notification wait handler
that's really waiting for the second response, but can't
tell the difference, we therefore see the message
"TIME_EVENT_CMD response - UID = 0x2601" instead of
"TIME_EVENT_CMD response - UID = 0x2701".
Fix this issue by making the TE removal synchronous as well,
this means that we wait for the response to that command
first, before there's any chance of sending a new one.
Also, to detect such issues more easily in the future, add
a warning to the notification handler that detects them.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is helpful for debugging the time event warning,
but also in general to see what's going on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All station commands must include a valid MAC ID,
the ID 0 is randomly valid in some cases, but we
must set the ID properly. Do that by passing the
right station and using its mac_id_n_color.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the firmware to know when DTIM beacons arrive
we have to program the DTIM time in TSF and system
time in the MAC context. Since mac80211 now tracks
the different times (on demand), this becomes easy.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlwifi-next tree removed IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
while the mac80211-next tree removed
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upper case macros for various chip attributes are slightly
difficult to read and are a bit out of characterto the other
tg3_<foo> attribute functions.
Convert:
GET_ASIC_REV(tp->pci_chip_rev_id) -> tg3_asic_rev(tp)
GET_CHIP_REV(tp->pci_chip_rev_id) -> tg3_chip_rev(tp)
Remove:
GET_METAL_REV(tp->pci_chip_rev_id) -> tg3_metal_rev(tp) (unused)
Add:
tg3_chip_rev_id(tp) for tp->pci_chip_rev_id so access styles
are similar to tg3_asic_rev and tg3_chip_rev.
These macros are not converted to static inline functions
because gcc (tested with 4.7.2) is currently unable to
optimize the object code it produces the same way and code
is otherwise larger.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's the same value as tp->pci_chip_rev_id so use that
instead. This makes all CHIPREV_ID_<foo> tests the same.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch I get many unaligned access warnings per packet,
this patches fixes them all. This should improve performance on some
systems like mips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000, e1000e, igb, igbvf and ixgbe.
The e1000, e1000e, igb and igbvf are single patch changes and the
remaining 11 patches are all against ixgbe.
The e1000 patch is a comment cleanup to align e1000 with the code
commenting style for /drivers/net. It also contains a few other white
space cleanups (i.e. fix lines over 80 char, remove unnecessary blank
lines and fix the use of tabs/spaces).
The e1000e patch from Koki (Fujitsu) adds a warning when link speed is
downgraded due to SmartSpeed.
The igb patch from Stefan (Red Hat) increases the timeout in the ethtool
offline self-test because some i350 adapters would sometimes fail the
self-test because link auto negotiation may take longer than the current
4 second timeout.
The igbvf patch from Alex is meant to address several race issues that
become possible because next_to_watch could possibly be set to a value
that shows that the descriptor is done when it is not. In order to correct
that we instead make next_to_watch a pointer that is set to NULL during
cleanup, and set to the eop_desc after the descriptor rings have been written.
The remaining patches for ixgbe are a mix of fixes and added support as well
as some cleanup. Most notably is the added support for displaying the
number of Tx/Rx channels via ethtool by Alex. Also Aurélien adds the
ability for reading data from SFP+ modules over i2c for diagnostic
monitoring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In ehea.h the minimal entries is 2^7 - 1:
#define EHEA_MIN_ENTRIES_QP 127
Thus change the module param description accordinglly
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes have made it so that MAX_SKB_FRAGS is now never less than 16.
As a result we were seeing issues on systems with 64K pages as it would
cause DESC_NEEDED to increase to 68, and we would need over 136 descriptors
free before clean_tx_irq would wake the queue.
This patch makes it so that DESC_NEEDED is always MAX_SKB_FRAGS + 4. This
should prevent any possible deadlocks on the systems with 64K pages as we will
now only require 42 descriptors to wake.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that TXDCTL.WTHRESH is set to 1 when BQL is enabled
and EITR is set to more than 100k interrupts per second to avoid Tx timeouts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for reading data from SFP+ modules over i2c.
Signed-off-by: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces instances where a return code from i2c operations
were checked against a list of error codes with a much simpler
if ( status != 0 ) check.
Some whitespace cleanups included.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that the SW lock is released after all i2c
operations complete in the retry code path.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for the ethtool set_channels operation.
Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the ethtool get_channels operation.
Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_setup_tc code is essentially the same code we need any time we have
to update the number of queues. As such I am making it available always and
just stripping the DCB specific bits out when DCB is disabled instead of
stripping the entire function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue. The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for ixgbe to configure the XPS queue mapping on
load. The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner. This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.
I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs. This essentially treats the two
groupings like they are two separate traffic classes.
In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.
I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64. The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On several machines with i350 adapters the ethtool offline self-test sometimes
fails. This happens because link auto negotiation may take longer than the
timeout of 4 seconds. Increasing the timeout by 1 seconds resolves the issue.
Output from a failing i350 offline self-test:
while [ 1 ]; do ethtool -t eth2 offline; done
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 1
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to address several race issues that become possible
because next_to_watch could possibly be set to a value that shows that the
descriptor is done when it is not. In order to correct that we instead make
next_to_watch a pointer that is set to NULL during cleanup, and set to the
eop_desc after the descriptor rings have been written.
To enforce proper ordering the next_to_watch pointer is not set until after
a wmb writing the values to the last descriptor in a transmit. In order to
guarantee that the descriptor is not read until after the eop_desc we use the
read_barrier_depends which is only really necessary on the alpha architecture.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed. As a result, users suspect that there is something wrong with
NIC. If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed. In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pacth fixes the parsing of the eee_timer driver parameter.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb and ixgbe. Most of the changes
are against igb, except for one patch against ixgbe.
There are 3 igb fixes from Carolyn which were reported by Dan
Carpenter which resolve issues found in the get_i2c_client(). Alex
does some cleanup of the igb driver to match similar functionality
in ixgbe on transmit. Alex also makes it so that we can enable the use
of build_skb for cases where jumbo frames are disabled. The advantage
to this is that we do not have to perform a memcpy to populate the header
and as a result we see a significant performance improvement.
Akeem provides 4 patches to initialize function pointers and do a
re-factoring of the function pointers in igb_get_variants() to assist
with driver debugging.
The ixgbe patch comes from Emil to reshuffle the switch/case structure
of the flag assignment to allow for the flags to be set for each MAC
type separately. This is needed for new hardware that does not have feature
parity with older hardware.
v2: updated patches 4 & 5 based on feedback from Ben Hutchings and Eric
Dumazet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used in next GRE_GSO patch. This patch does
not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Before the device is opened, the carrier state should be off. It
will not race with the link interrupt if we set it before calling
register_netdev().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't set the default size to 128K if it is 5762. Instead, rely on the
size we obtain from NVRAM location 0xf0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip supports Energy Efficient Ethernet. The existing code only
supports a smaller set of devices with 5718 PCI ID. Expand support for
all devices with the same 5717 B0 chip ID.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch also adds a couple of fixes
- For the 57766 and non Ax versions of 57765, bootcode needs to setup
the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
Unfortunately, it does not have enough room in the selfboot case (i.e.
devices with no NVRAM). The driver needs to implement this.
- For performance reasons, the 2k DMA engine mode on the 57766 should
be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nvram functions are exported and used by some normal drivers. To
prevent name clashes with ofter parts of the kernel code add a bcm47xx_
prefix in front of the function names and the header file name.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4744/
Signed-off-by: John Crispin <blogic@openwrt.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRAuO3AAoJEHm+PkMAQRiGbfAH/1C3QQKB11aBpYLAw7qijAze
yOui26UCnwRryxsO8zBCQjGoByy5DvY/Q0zyUCWUE6nf/JFSoKGUHzfJ1ATyzGll
3vENP6Fnmq0Hgc4t8/gXtXrZ1k/c43cYA2XEhDnEsJlFNmNj2wCQQj9njTNn2cl1
k6XhZ9U1V2hGYpLL5bmsZiLVI6dIpkCVw8d4GZ8BKxSLUacVKMS7ml2kZqxBTMgt
AF6T2SPagBBxxNq8q87x4b7vyHYchZmk+9tAV8UMs1ecimasLK8vrRAJvkXXaH1t
xgtR0sfIp5raEjoFYswCK+cf5NEusLZDKOEvoABFfEgL4/RKFZ8w7MMsmG8m0rk=
=m68Y
-----END PGP SIGNATURE-----
Merge branch 'omap/multiplatform-fixes', tag 'v3.8-rc5' into next/multiplatform
The omap multiplatform support uncovered a bug in the cwdavinci_cpdma
code and was missing two drivers that are enabled now but are not
quite ready for multiplatform, as found by allyesconfig builds.
There is also a conflict generated by automated merge in
arch/arm/mach-omap2/drm.c between a bug fix that went into v3.8-rc5
and a different version of the same fix that went into the
omap/multiplatform branch. This merge removes the extraneous
#include that was causing build errors.
* omap/multiplatform-fixes:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the support for ARM AM33xx in multiplatform kernels
in 3.9, an older bug appears in ARM allmodconfig:
When the cpsw driver is built as a module with cpdma
support enabled, it uses symbols that the cpdma driver
does not export.
Without this patch, building allmodconfig results in:
ERROR: "cpdma_ctlr_int_ctrl" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_control_set" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_ctlr_eoi" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
This patch reshuffles the switch/case structure of the flag assignment to
allow for the flags to be set for each MAC type separately. This is needed
for new HW that does not have feature parity with older HW.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies igb_get_invariants function by moving all implemented
function pointers in this function to individual separate functions,
based on their functionalities, this would make debugging much easier.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes MAC function pointers for device configuration.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes NVM function pointers for device configuration.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes PHY function pointers for device configuration.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After reviewing the igb and ixgbe code I realized there are a few issues in
how the code is structured. Specifically we are not checking the size of the
buffers being used in transmits and we are not using the same value to
determine when to stop or start a Tx queue. As such the code is prone to be
buggy.
This patch makes it so that we have one value DESC_NEEDED that we will use for
starting and stopping the queue. In addition we will check the size of
buffers being used when setting up a transmit so as to avoid a possible buffer
overrun if we were to receive a frame with a block of data larger than 32K in
skb->data.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch correctly resolves the sparse warnings found with this
function.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the allocation function in igb_get_i2c_client to use
GFP_ATOMIC instead of GFP_KERNEL because we have a spinlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where we check for irq's disabled then exit after
explicitly disabling them with spin_lock_irqsave.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can enable the use of build_skb for cases
where jumbo frames are disabled. The advantage to this is that we do not
have to perform a memcpy to populate the header and as a result we see a
significant performance improvement.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Otherwise memory corruption occurs when using channel contexts (ATM when
param 'channel' > 1).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the casts of the first argument of memset.
Neaten the style by using the sizeof the actual variable
being memset not the sizeof the type of variable.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These messages don't seem to be errors but notifications
that some attribute isn't quite right.
Don't mark them as errors.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch check output of pci_map_single() calls. I missed them on
my previous patch "iwlegacy: check for dma mapping errors", which
fixed only pci_map_page() calls.
To handle remaining possible dma mappings errors, we need to rearrange
ilXXXX_tx_skb() and il_enqueue_hcmd() functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check output of dma_map_single functions which nowadays can fail (when
IOMMU is used). On write_beacon callbacks just print error, similar
like padding error is handled by rt2800_write_beacon.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for handling of PCIe sleep cookie depending
upon device properties. Some PCIe devices need sleep cookie probing
before accessing HW while some others don't. A new sleep_cookie
variable is defined as part of mwifiex_pcie_card_reg strcture and
set/reset as per device capability.
Sleep cookie is allocated/accessed/freed only when flag sleep_cookie
for this particular device is enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the number of drivers in the rtlwifi family has grown, the Kconfig
section for them has grown unwieldy. This change has two effects: (1)
Variable RTLWIFI_DEBUG is documented, and (2) the entries for the
drivers that depend on RTLWIFI are indented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ccode is not NUL terminated. Presumably insisting on a terminator makes
brcms_c_country_valid() return false when it's not intended. ccode[2]
is sprom->leddc_on_time.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a less obvious error on one hand, and prevents futher
similar errors by disambiguating and optimizing RxFCB indication,
on the other hand.
The error consists in NETIF_F_HW_VLAN_TX flag being used as an
indication of Rx FCB insertion. This happened as soon gfar_uses_fcb(),
which despite its name indicates Rx FCB insertion, started
incorporating is_vlan_on().
is_vlan_on(), on the other hand, is also a misleading construct because
we need to differentiate b/w hw VLAN extraction/VLEX (marked by VLAN_RX
flag) and hw VLAN insertion/VLINS (VLAN_TX flag), which are different
mechanisms using different types of FCBs.
The hw spec for the RxFCB feature is as follows:
In the case of RxBD rings, FCBs (Frame Control Block) are inserted by
the eTSEC whenever RCTRL[PRSDEP] is set to a non-zero value. Only one
FCB is inserted per frame (in the buffer pointed to by the RxBD with
bit F set). TOE acceleration for receive is enabled for all rx frames
in this case.
This patch introduces priv->uses_rxfcb field to quickly signal RxFCB
insertion in accordance with the specification above.
The dependency on FSL_GIANFAR_DEV_HAS_TIMER was also eliminated as
another source of confusion. The actual dependency is to priv->hwts_rx_en.
Upon changing priv->hwts_rx_en via IOCTL, the gfar device is being
restarted and on init_mac() the priv->hwts_rx_en flag determines RxFCB
insertion, and rctrl is programmed accordingly. The patch takes care
of this case too.
Though maybe not as self documenting as the inlining version uses_fcb(),
priv->uses_rxfcb has the main purpose to quickly signal, on the hot path,
that the incoming frame has a *Rx* FCB block inserted which needs to be
pulled out before passing the skb to the stack. This is a performance
critical operation, it needs to happen fast, that's why uses_rxfcb is
placed in the first cacheline of gfar_private.
This is also why a cached rctrl cannot be used instead: 1) because
we don't have 32 bits available in the first cacheline of gfar_priv
(but only 16); 2) bit operations are expensive on the hot path.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The controller's ref manual states clearly that when the hw Rx vlan
offload feature is enabled, meaning that the VLEX bit from RCTRL is
correctly enabled, then the hw performs automatic VLAN tag extraction
and deletion from the ethernet frames. So there's no point in trying to
increase the rx buff size when rxvlan is on, as the frame is actually
smaller.
And the Tx vlan hw accel feature (VLINS) has nothing to do with rx buff
size computation.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No return code is expected from gfar_process_frame(), hence
change it to return void.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group run-time critical fields within the 1st cacheline (32B)
followed by the tx|rx_queue reference arrays and the interrupt
group instances (gfargrp), all cacheline aligned.
This has several benefits. Firstly comes the performance benefit
by having the members required by the driver's hot path re-grouped
in the structure's first cache lines, whereas the unimportant
members were pushed towards the end of the struct.
Another benefit comes from eliminating a 24 byte memory hole that
was rendering gfar_priv's 2nd cacheline useless. The default gcc
layout of gfar_private leaves an implicit 24 byte hole after the
errata (enum) member. This patch fixes it.
The uchar bitfields were pushed towards the end of the struct
as these are not run-time performance critical (used for init
time operations). Because there is no other 2 byte member
around to couple the uchar bitfields memeber with, we will
have an addititnal 2 byte hole after the bitfields. This is
unsignificant however, and it doesn't influence gfar_priv's
size, because the whole structure is padded to be a 32B multiple.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device pointer (dev) to simplify the code and to
avoid double indirections, especially on the hot path.
Basically, instead of accessing priv to get the ofdev
reference and then accessing the ofdev structure to
dereference the needed dev pointer, we will get the
dev pointer directly from priv.
The dev pointer is required on the hot path, see gfar_new_rxbdp
or gfar_clean_rx_ring (or xmit), and this patch makes
it available directly from priv's 1st cacheline.
This change is reflected at asm level too, taking (the hot)
gfar_new_rxbdp():
initial version -
18c0: 7c 7e 1b 78 mr r30,r3
18d0: 81 69 04 3c lwz r11,1084(r9)
18d8: 34 6b 00 10 addic. r3,r11,16
18dc: 41 82 00 08 beq- 18e4
patched version -
18d0: 80 69 04 38 lwz r3,1080(r9)
18d8: 2f 83 00 00 cmpwi cr7,r3,0
18dc: 41 9e 00 08 beq- cr7,18e4
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The specs prescribe an immediate read of the interrupt mask after
disabling interrupts. This patch updates the driver to match the
specs.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the credit timer is left armed after calling
xen_netbk_remove_xenvif(), then it may fire and attempt to schedule
the vif which will then oops as vif->netbk == NULL.
This may happen both in the fatal error path and during normal
disconnection from the front end.
The sequencing during shutdown is critical to ensure that: a)
vif->netbk doesn't become unexpectedly NULL; and b) the net device/vif
is not freed.
1. Mark as unschedulable (netif_carrier_off()).
2. Synchronously cancel the timer.
3. Remove the vif from the schedule list.
4. Remove it from it netback thread group.
5. Wait for vif->refcnt to become 0.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reported-by: Christopher S. Aker <caker@theshore.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
netbk_count_requests() could detect an error, call
netbk_fatal_tx_error() but return 0. The vif may then be used
afterwards (e.g., in a call to netbk_tx_error().
Since netbk_fatal_tx_error() could set vif->refcnt to 1, the vif may
be freed immediately after the call to netbk_fatal_tx_error() (e.g.,
if the vif is also removed).
Netback thread Xenwatch thread
-------------------------------------------
netbk_fatal_tx_err() netback_remove()
xenvif_disconnect()
...
free_netdev()
netbk_tx_err() Oops!
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Christopher S. Aker <caker@theshore.net>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bd329e1 ("net: cdc_ncm: do not bind to NCM compatible MBIM devices")
added a test for a CDC MBIM altsetting, implementing the cdc_ncm part of
MBIM backward compatibility support. This intentionally made the driver
behave differently for CDC NCM devices with 2 alternate settings for the
Communication interface, depending on whether or not CONFIG_USB_NET_CDC_MBIM
was enabled. This is correct iff alternate setting #1 really *is* a MBIM
setting. If not, then NCM probing will use a different altsetting than before,
possibly causing probing failures depending on CONFIG_USB_NET_CDC_MBIM.
Fix by setting the altsetting back to default after the test, restoring the
previous behaviour for non MBIM devices.
This bug causes probing of Huawei E3276 devices to fail when the MBIM driver
is enabled, because these devices have a second alternate setting with no CDC
functional descriptors.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Reported-and-tested-by: Jonathan A. <yo.natan@hotmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT91RM9200 driver call devm_request_irq() and therefore should
depend on GENERIC_HARDIRQS to prevent link/compile errors on plaforms
without GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a user adds bridge neighbors, allow him to specify VLAN id.
If the VLAN id is not specified, the neighbor will be added
for VLANs currently in the ports filter list. If no VLANs are
configured on the port, we use vlan 0 and only add 1 entry.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTM_GETLINK dump the vlan filter list of a given
bridge port. The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some callers may want to know if PHY write succeed. Also make PHY
functions static, they are not exported anywhere.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code expects that the last word (with valid bit)
of an MCC compl is DMAed in one shot. This may not be the case.
Remove this assertion.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpdma_chan_destroy() on a NULL pointer is a no-op, so the NULL check in
cpdma_ctlr_destroy() can safely be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interrupts are disabled, an RX condition can occur but
it is not reported when enabling interrupts again. We need to check
RSR and use napi_reschedule() if condition is met.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch cef401de7b (net: fix possible wrong checksum
generation) fixed wrong checksum calculation but it broke TSO by
defining new GSO type but not a netdev feature for that type.
net_gso_ok() would not allow hardware checksum/segmentation
offload of such packets without the feature.
Following patch fixes TSO and wrong checksum. This patch uses
same logic that Eric Dumazet used. Patch introduces new flag
SKBTX_SHARED_FRAG if at least one frag can be modified by
the user. but SKBTX_SHARED_FRAG flag is kept in skb shared
info tx_flags rather than gso_type.
tx_flags is better compared to gso_type since we can have skb with
shared frag without gso packet. It does not link SHARED_FRAG to
GSO, So there is no need to define netdev feature for this.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker says:
====================
Eric noticed that the handling of local u64 ethtool counters for
this driver commonly found on Freescale ppc-32 boards was racy.
However, before converting them over to atomic64_t, I noticed
that an internal struct was being used to determine the offsets
for exporting this data into the ethtool buffer, and in doing
so, it assumed that the counters would always be u64. Rather
than keep this implicit assumption, a simple code cleanup gets
rid of the struct completely, and leaves less conversion sites.
The alternative solution would have been to take advantage of
the fact that the counters are all relating to error conditions,
and hence make them internally u32. In doing so, we'd be assuming
that U32_MAX of any particular error condition is highly unlikely.
This might have made sense if any increments were in a hot path.
Tested with "ethtool -S eth0" on sbc8548 board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the horribly coded of_count_named_gpios() with a
call to of_count_phandle_with_args() which is far more efficient. This
also changes the return value of of_gpio_count() & of_gpio_named_count()
from 'unsigned int' to 'int' so that it can return an error code. All
the users of that function are fixed up to correctly handle a negative
return value.
v2: Split GPIO portion into a separate patch
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
While looking at some asm dump for an unrelated change, Eric
noticed in the following stats count increment code:
50b8: 81 3c 01 f8 lwz r9,504(r28)
50bc: 81 5c 01 fc lwz r10,508(r28)
50c0: 31 4a 00 01 addic r10,r10,1
50c4: 7d 29 01 94 addze r9,r9
50c8: 91 3c 01 f8 stw r9,504(r28)
50cc: 91 5c 01 fc stw r10,508(r28)
that a 64 bit counter was used on ppc-32 without sync
and hence the "ethtool -S" output was racy.
Here we convert all the values to use atomic64_t so that
the output will always be consistent.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The gfar_stats struct is only used in copying out data
via ethtool. It is declared as the extra stats, followed
by the rmon stats. However, the rmon stats are never
actually ever used in the driver; instead the rmon data
is a u32 register read that is cast directly into the
ethtool buf.
It seems the only reason rmon is in the struct at all is
to give the offset(s) at which it should be exported into
the ethtool buffer. But note gfar_stats doesn't contain
a gfar_extra_stats as a substruct -- instead it contains
a u64 array of equal element count. This implicitly means
we have two independent declarations of what gfar_extra_stats
really is. Rather than have this duality, we already have
defines which give us the offset directly, and hence do not
need the struct at all.
Further, since we know the extra_stats is unconditionally
always present, we can write it out to the ethtool buf
1st, and then optionally write out the rmon data. There
is no need for two independent loops, both of which are
simply copying out the extra_stats to buf offset zero.
This also helps pave the way towards allowing the extra
stats fields to be converted to atomic64_t values, without
having their types directly influencing the ethtool stats
export code (gfar_fill_stats) that expects to deal with u64.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the MPC5200 FEC ethernet driver relied upon the bootloader
(U-Boot) to write the MAC address into the ethernet controller
registers. The Linux driver should not rely on such a thing. So
lets read the MAC address from the DT as it should be done here.
The following priority is now used to read the MAC address:
1) First, try OF node MAC address, if not present or invalid, then:
2) Read from MAC address registers, if invalid, then:
3) Log a warning message, and choose a random MAC address.
This fixes a problem with a MPC5200 board that uses the SPL U-Boot
version without FEC initialization before Linux booting for
boot speedup.
Additionally a status line is now be printed upon successful
driver probing, also displaying this MAC address.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode
Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
both the interface as timestamping information doesn't contain port
information.
Constrains
* Reserved VID of One port should not be used in other interface which will
enable switching functionality
* Same VID must not be used in both the interface which will enable switching
functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As CPTS is common module for both EMAC in Dual EMAC mode so making cpts as
pointer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Introduced parameter to add port number for directed packet in cpdma_chan_submit
* Source port detection macro with DMA descriptor status
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Here is another handful of late-breaking fixes intended for the 3.8
stream... Hopefully the will still make it! :-)
There are three mac80211 fixes pulled from Johannes:
"Here are three fixes still for the 3.8 stream, the fix from Cong Ding
for the bad sizeof (Stephen Hemminger had pointed it out before but I'd
promptly forgotten), a mac80211 managed-mode channel context usage fix
where a downgrade would never stop until reaching non-HT and a bug in
the channel determination that could cause invalid channels like HT40+
on channel 11 to be used."
Also included is a mwl8k fix that avoids an oops when using mwl8k
devices that only support the 5 GHz band.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This partially reverts commit 44ba973699.
rate_control_rate_init assumes the rate_init member of
struct rate_control_ops is not NULL therefore not initializing it leads to
an oops as soon the driver succesfully associates to an AP.
The removal of rate_update from 44ba973699
is ok because rate_update is checked for NULL before being
called.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the code more readable, and while at it also
add a missing "break" to avoid checking handlers
that cannot be used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>